Search Documents

By P T. Hick, T J. Cudahy, M S. Caccetta

Dust derived from mining and handling of ore has been identified as a major concern for the mining industry in Australia and may be critical to the future viability of some resource industries (CSIRO, 1999). Operational techniques to derive accurate measurements of anthropogenic dust on vegetation and infrastructure are necessary for the long-term management and monitoring of the environment surrounding mining operations. Airborne hyperspectral VNIR-SWIR systems can potentially provide these monitoring data. This paper outlines a method developed for deriving quantitative measurements of dust quantity on mangroves using remotely-sensed airborne hyperspectral data. The results show that it is possible to detect and quantitatively map iron oxide dust distribution using properly calibrated airborne visible to short wave infrared (VNIR-SWIR) data.

Jan 1, 2002

Railway cuttings require the highest care in design and construction, as the pro- bability of failure concept does not allow any risks to be taken with hundreds of lives being dependent on continued stability. The usual geological influences on stability such as bedding dip and faulting are often discus- sed, but other major problems may come from the presence of sheet joints, cross joints differential weathering and seasonal or daily changes of ground water level. The design of rail cuttings has taken little note of the problems imposed by cons- truction methods, and low cost quarrying methods may seriously weaken a designed shape. The presence of berms and drainage ditches is often difficult to achieve as blasting imposes cumulative stresses and jointing on rocks. Contractors face difficulties in bidding extensive rock cuttings as variations in rock properties are often concealed and overshoot- ing the toe of a batter can easily occur. Modern blasting methods offer some solutions, but the best guide to safe successful cuttings is extensive investigation and the continued involvement of engineering geology at the stages of feasibility, design, construction and maintenance. Two case histories show the influence of folding, faulting and construction methods in the case of slope failure and slope stability.

Jan 1, 1979

Underground measurements, observations and computed simulations, started a long time ago were concerning the study of : - occurence of typical rockburst, - inducing, stretching of main fractures in the roof of caved longwalls. They made obvious a foundamental phenomenon of inducing of strata fractures involving contact be- tween two layers quite different in their elastic characteristics : coalseam and rocklayer.. The start of primary cracks in maximum abutment zone takes place in the rock near the contact surface. It is opening of crevasses induced by traction stress component resulting of difference of rigidity of both materials and no sliding on in- terface. Occurence and stretching of these crevas- ses are a rheological phenomenon so that the rate of advance and stops of the face influence the distance between the crevasses and the stretching of these ones. The characteristics of these cracks in space and time affect mining conditions. So it is for fractures proximity and expan- sion inducing eventual blocks formation in longwall roofs in front of faces, for depth and delay of road- ways ribsides fracturing, inducing some rockbursts. In longwalls roofs, cracks initiated in front of a face can be either quite close or quite distant each from the other one, according to the depth of crushed coal in front of the face, which af- fects also extension of the cracks.

Jan 1, 1988

During the past five years there has been a transformation in the operating costs which apply to narrow vein mining. Mechanised methods including sublevel uphole retreat and narrow vein cut and fill are now proven. Other methods, such as vein mining by horizontal drilling from a raise platform are currently being tried in Australia.The important factors which affect the cost and appropriateness of each method include: ore continuity, the planarity of the wall contacts, relative hardness of ore and wall rocks and the dip bf the deposit.Drawing on current operating costs from a number of mines and on recent feasibility studies, a methodology for estimating the costs of narrow vein mining is presented. These costs are then placed in their economic context with regard to ore grade and mining rate.

Jan 1, 1993

By Cortes JP

In a dynamic environment such as the Star Mountains of Papua New Guinea Geotechnical Engineering for the Ok Tedi Project must be described as both interesting and challenging. To be effective a reasonable sized team of dedicated people is required with occasional supplementation by specialist consultants and an annual review process. Ok Tedi Mining Limited's (OTML) Geotechnical Section has a vision to be recognised as the leading mine-based geotechnical engineering section in PNG and to be world class by any international standards. This paper deals with the organisational and operational duties of the Geotechnical Section at the Ok Tedi Mine. One of our major roles is in the area of safety, and in particular in the early warning of natural and mining induced geological hazards that may affect safety and/or productivity. The major activities in- clude geotechnical inspections (pit, waste dumps, tunnels, re- gional), data collection activities and database management, geotechnical design and control work.

Jan 1, 1997

By Dmitrievskaya TY, Cheremnykh PA, Kuftinova IV, Yaremenko VN

The comprehensive processing of raw materials and the tendency to waste-free production require the combination of various methods of concentrating mineral resources. Magnetic separation, an ecologically clean method of concentration, is one step in the technological cycle of ore processing, and cleaning and classifying of raw materials. Separators with superconducting magnetic systems cooled by liquid helium are the novel equipment for practical concentration. Recently, high-gradient (HGMS) and open-gradient (OGMS) magnetic separators using the effect of superconductivity have appeared. The separators of the first type are expedient in the head-end of the technological cycle, as they are most efficient for processing of particles 100 ¦m and greater in size. In this case the main task is to obtain pure tailings with a minimum amount of the useful component. This method allows the essential reduction in the cost of the subsequent crushing and grinding, because only the magnetic concentrate is directed to further processing. The separators of the VGMS type are used more efficiently in the final stages of the concentration cycle to condition the end product. The present work is devoted to the theoretical and experimental investigation of the motion of weakly magnetic particles in the working chamber of superconducting separators of the open-gradient magnetic separator (OGMS) and HGMS types. The flat OGMS is equipped by a magnetic system with NbTi racetracks cooled by liquid helium. The chamber is divided into zones by partitions parallel to the plane of the magnetic system. It is shown how, depending on the number of the zones and their depths, the extraction function of the OGMS varies and the transition from the OGMS to the HGMS occurs. The particles 2 mm and less in size are considered. The extraction parameter distribution of the particles was measured for a multicomponent weakly magnetic ore. It was experimentally shown that xD2 is the extraction parameter for the particles in the OGMS on condition that (p-po)D /l8/tl/g

Jan 1, 1993

By Swift J. D

A key parameter affecting the performance of gravity thickeners in hydrometallurgical processing operations is the aggregation state of the feed after the addition of a flocculant. New procedures which measure the settling ratelsize relationship and the size distribution of aggregates in their process liquors have been used to quantify the aggregation state of the feedwell, overflow and underflow streams in a tailings thickener. The data obtained have been related to the thickener's operation and to a change in the flocculant dosage. A comparison is also made between the settling rate/size relationships determined with these new procedures and the mud-line settling rates from cylinder tests.

Jan 1, 1991

The InLine Pressure Jig represents a breakthrough in digging technology Its design incorporates a unique combination of features previously utilised in conventional jig design. In particular, a moveable screen and circular bed are used to excellent effect. However, a major design innovation is the encapsulation of the circular bed within a vessel - allowing the equipment to operate under pressure. This innovation eliminates free water surface, improves the dynamics within the separation layer (crossflow) and provides significant cost savings in the handling of slurries. Recent research results have indicated its capacity to achieve high recoveries and upgrade ratios in the gravity separation of Minerals.

Jan 1, 1997

By Biswas AK

The solubility of nickel in matte smelt- ing slags, both as oxide and in the metallic form, is predicted using the results of a recent experimental work carried out with lime- free iron silicate slags as well as slags containing lime. Predicted solubilities are much lower than the nickel content of smelting slags, indicating that entrapped and possibly dissolved matte could be the major cause of nickel losses in such slags.

Jan 1, 1975

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

A number of suggestions have been made to improve the design of cells used for electro winning and electro refining of metals. Most of these designs have been aimed at increasing the current density used in order to improve cell capacity, although the purpose of some has been to produce electro deposited metals in a continuous manner. Improvements in the electrolyte flow pattern in conventional cells have resulted in an increase in the rate of mass transport of metal ions to the electrode surface; giving rise to lower concentrat- ion polarization and an improvement in the nature of the product obtained, Other cell designs are based on a moving electrode, usually a rotating disk, and these may include provision for removal of the product in a continuous manner, The maximum current density which can be used in an electro- lytic deposition process is determined by the limiting diffusion current, the physical nature of the, product, the purity of the product required and by the increase in power costs which result from the higher cell voltages, This paper examines the properties of an agitated bed of particles as an electrode system when used for a metal deposition Process,

Jan 1, 1969

By Jackson D. G

Iron ore mineralisation in the Paraburdoo environs is known to extend almost continuously over a strike length of 55 kilometres. Six formations of the Mount Bruce Supergroup con- tain high grade mineralisation in varying degrees of importance. Ore is currently being mined from the Joffre and Dales Gorge Members of the Brockman Iron Formation, with smaller, less significant amounts, occasionally taken from the lowermost units of the Weeli Wolli Formation and the upper parts of the Mount McRae Shale. Regional mapping has demonstrated the existance locally of a major unconformity at the base of the Wyloo Group sediments out- cropping south of the minesite. The basal con- glomerates at the unconformity are sometimes mineralised at Paraburdoo. A supergene enrich- ment process controlled by structure, strati- graphy and topography is the only one which can satisfactorily explain the disposition and chemistry of the Paraburdoo iron orebodies.

Jan 1, 1979

By Greaves M. C, Amos M. D

A study was made of the instrumentation and technique of atomic absorption spectroscopy developed by Walsh of the Commonwealth Scientific and Industrial Research Organisation (CSIRO), Australia.The method was evaluated for the determination of silver in lead sulphide concentrate. The precision of the procedure developed is equal to that of the uncorrected fire assay method and the accuracy is greater.Brief mention is made of the use of this technique for the determination of silver and other elements in ores and concentrator products.

Jan 1, 1994

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995

This paper describes the effects of physical variables in dewatering of mineral slurries with air as the filtrate displacing medium. Using a mathematical model with material related constants measured in laboratory dewatering curves are simulated for vacuum and pressure filtration. Four different mineral slurries are studied. Basic dewatering curves with variation in air-pressure are shown with iso-energy lines. Variables such as air pressure, feed concentration, cake thickness and cake formation pressure are discussed.

Jan 1, 1989

By Mistra M, Hu JS, Wadsworth ME

The fluorite/oleate system has been studied extensively since the begin- nings of flotation research. The well-defined relatively simple crystal structure of fluorite and its ionic bonding make it a model system for study. Our understanding of fluorite/ oleate flotation chemistry continues to grow but as yet remains incomplete. Besides a review of our understanding of this system, recent findings are presented in this paper, and new research horizons are identified.

Jan 1, 1984

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

By Snowdowne J. B H

Rand Mines, Limited, located in Johannesburg, Republic of South Africa has recently completed feasibility studies which have lead to the initiation of two major coal strip mining ventures. A minicomputer based mine planning system was developed to perform the feasibility studies. The broad approach of this system is to utilise inter.-actively the specialist skills and interpretative abilities of mining engineers and geologists. This paper reports briefly on the outline of the system and at greater length upon certain aspects of its use.

Jan 1, 1977

By Williams RC

Overlying the coal deposits of the Sydney Basin are several lakes and other bodies of water. These include the Pacific Ocean, Lake Macquarie, the Tuggerah Lakes and the stored waters of the dams of the New South Wales Metropolitan Water Sewerage and Drainage Board. The coal beneath these bodies of water amounts to hundreds of millions of tons. Colliery workings have approached these areas of water and in some instances first 1"orkings of bord and pillar have taken place oi_eshh the water. he problem which now faces mine manage- and other interested authorities involves the determination of the maximum ;mount of coal which can be safely extracted from beneath the water. There are many factors to be considered including the depth of cover, seam thickness, geological details and strata movements.

Jan 1, 1972

By Turner T. M

The problem of metering fine particulate material at low flowrate is often encountered in metallurgical experiment. This note describes a feeder which wa developed to provide metered flows of copper sulphide concentrate in the range of 0'1-0'7 g/min.It is believed that the present device is easier to operate than previously described feeders (e.g. Hamor and Smith, 1971). It may have applications in the field of analytical chemistry, as well as in metallurgical investigations.

Jan 1, 1978