Search Documents

By W. E. Hale

An area of about 7,000 square miles within the eastern part of the Grenville Sub-province is underlain chiefly by granitic gneisses. There are, however, some exposures of mafic rocks which warrant further investigation, and some attractive structures, particularly basins, which deserve additional economic consideration. T HIS paper describes in a very general fashion the economic and geological features of an area of about 7,000 square miles on the north shore of the Gulf of St. Lawrence in the eastern part of the Grenville Sub-province (Figure 1). The scarcity of published geological data on this part of the Cana-dian Shield (DePuyjalon, 1899 and Longley, 1944) justifies the presentation of these tentative results. It should be appreciated, however, that the information which follows was acquired in a rapid reconnaissance designed specifically to out-line what might be interpreted as favourable geological environments for the occurrence of economic minerals, rather than to produce an authoritative analysis of the geological history of the region.

Jan 1, 1962

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005

By C. Blawert

In spite of various corrosion studies on HPDC AZ91, there is no clear indication which microstructure gives the best corrosion performance. The skin with its fine microstructure is sometimes reported to have the best corrosion resistance, but there is no clear definition of the skin. If the skin is the outermost part of the casting and nothing is removed from it, then it is contaminated and the corrosion resistance is low. If the outermost skin is removed (about 25 µm) then a better corrosion resistance can be obtained. However this does not automatically mean that there is no other region in the bulk of the casting which could have a similar or even better corrosion resistance. Indeed, the corrosion measurements including potentiodynamic polarization and long term electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin about 100 pm thick. The thickness of this region is more or less independent from the thickness of the casting section. The surface region is free from any dendritic grain growth which influences the amount and distribution of the 13-phase and therefore the distribution of the most important alloying element Al. This could explain the different corrosion behavior. Further reason can be found in the enrichment of some impurities such as Fe in the near surface.

Jan 1, 2006

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

The introduction consists of back-ground information, of an historical and statistical nature, relating to the Thompson mine. The geological presentation is based on illustrations that are intended to provide a progressively closer look at the ore occurrence. The illustrations consist of an index map, a geological map of a 15-by 85-mile area including the Thompson mine, a series of four maps dealing with the geophysics and geology of a 6-by 4\f.j-mile area at Thompson, a mine level plan and corresponding section, two sto11e 11lans and corresponding sections, and photo-graphs and photomicrogra11hs of the various one types. T HE Thompson mine is located about 400 miles due north of Winnipeg. The ore deposit was dis-covered in February, 1956. Five years later on March 25, 1961, the Thompson production facilities were officially dedicated with the shearing of the first nickel produced at the Thompson refinery. Full production, at an annual rate of more than 75,000,000 lbs. of refined nickel, was attained later in the year.

Jan 1, 1963

By P. K. Kaiser, D. D. Tannant

"A support system for large ground convergence conditions or burst-prone ground must contain holding elements (rockbolts, cable bolts, etc.) that are strong yet capable of sustaining large deformations, i.e., they must absorb as much energy as possible. Steel wire rope anchored in a borehole by a friction bolt provides these desired yield characteristics if the frictional anchorage is placed deep enough into the rockmass, i.e., in non-yielding rock or beyond the expected depth of rock ejected during a rockburst. Pull-out tests were conducted on wire ropes anchored by inflated Swellex bolts to assess the feasibility of this support concept. The test results demonstrate that a Swellex bolt generates a frictional anchorage that allows the wire rope to slide at high loads and to absorb significantly more energy than either a Swellex bolt alone, or a cement-grouted cable.The rope/friction bolt combination can be engineered to provide the desired energy absorption and allowable deformation by varying the installed lengths of the friction bolt and the rope. For yielding rope support, the contact length between the rope and Swellex bolt must be short enough to ensure that the rope can slip well before its tensile capacity is reached. A safe maximum overlap length is about one metre for the wire rope used in this testing. When used as support in the backs of drifts, a swaged button on the ropes end must be used to ultimately mobilize the full rope capacity thereby protecting against gravity-driven falls of ground."

Jan 1, 1995

By John Tribe

"This paper gives the organizational history of Luscar Ltd. and its various coal producing operations. Each 0/ the operations is then described individually. They include the Bienfait Mine, the Boundary Dam Mine, the Diplomat Mine, the Luscar Mine and the Coal Valley Mine. The company's plans/or expansion are also discussed. IntroductionLuscar Ltd. is an Edmonton-based energy company formed in 1967 through an amalgamation of two pioneer coal companies-Mountain Park Collieries and Luscar Coals Ltd. In 1912, Mountain Park Collieries initiated the development of an underground mine in the Coal Branch area of Alberta. This mine necessitated the establishment of a townsite and the provision of rail access. The second operation, Luscar Coals Ltd., was established in 1921 at Luscar, Alberta. This was also an underground operation and required the development of a rail spur and townsite. The product from both mines was used to fuel railway steam locomotives until the 1950's. The market demand for coal decreased as the use of the diesel locomotive increased, so that these operations were finally closed in 1954. Through the amalgamation of the two companies in 1967, however, Luscar Ltd. was formed to become an active participant in the revival of coal operations. Western Canadian Luscar Ltd. is involved in the exploration, development, production and marketing of coal, coal products, oil and gas. Luscar Ltd. is currently participating in five producing mines (Fig. I). The Diplomat Mine, approximately 125 miles southeast of Edmonton, was in production when it was acquired in 1949 by Luscar Coals Ltd. In 1966, the Bienfait Mine and char plant were added. The Luscar Mine, which is a 50/50 joint venture of Luscar Ltd. and the Consolidation Coal Company of Canada, and is operated by Cardinal River Coals Limited, started production in 1969 on the original Luscar Coals Ltd. mine site. The Boundary Dam Mine was opened in 1974. Both the Bienfait and Boundary Dam operations are located in the lignite coal fields of southeastern Saskatchewan. The most recent addition to the group is the Coal Valley Mine, 40 miles southwest of Edson, Alberta. It commenced commercial production in July, 1978 under the operation of Luscar Stereo (1977) Limited."

Jan 1, 1980

By Ronald E. Pike

"PREFACEAt the CIM Annual General Meeting in Quebec City, R.E. Pike of The Toronto-Dominion Bank described how the Canadian banking industry worked with the minerals industry to assemble the large capital requirements for resource projects in Canada and overseas. He developed a profile of the mining industry and Canadian banking, both being important sectors of the Canadian economy and global in context. He also outlined the banking and financing partnership that existed in the past. In looking to the future and challenge that lies ahead f or each industry, Mr. Pike questioned whether the financing practices of the 1970s will be acceptable over the next decade. In that regard, he highlighted the risks that impact on each industry and illustrated how that financing partnership might evolve in response to those forces. The folio wing is a synopsis of his paper.IntroductionThe Canadian mining and metals industry is prominent in the domestic economy and respected internationally. Any measure of its performance illustrates that status-percentage of GNP, employment, exports, capital investment, size relative to other producing nations, etc.Energy, Mines and Resources Canada has forecast that the non-fuel minerals industry will grow in real terms by an average annual rate of 3.0% over the period 1981 to 1991. Using the GNP as reference, that growth in non-fuel mineral production will represent 7.7% of GNP. In translating that growth to capital expenditure, the EMR Canada estimates the aggregate amount at $43.8 billion ('79 dollars) or approximately 12% of total business investment in Canada during the 10-year period.About half of the $43.8 billion will be devoted to the ferrous sector-$8.4 billion in iron ore mining and $12.4 billion in the steel industry. Capital investment in nonferrous s projects is estimated at $13.3 billion, and it is projected at $6.7 billion for industrial minerals. The residual $3.0 .billion is exploration spending."

Jan 1, 1982

By E. Y. Dougherty

Introduction As practised during the last two years at the Vipond Consolidated gold mine, mining geology has meant the application of geology to the problem of finding, developing, and mining ore. This article reviews the results attained in Vipond mining geology as thus defined. Most effort was directed toward clarifying and interpreting the tangible physical causes of vein and ore localizations, and in the following pages these questions are dealt with in considerable detail. Discernment of the influence of rock folding and deformation on the localization of veins, and of the influence of certain structures and rocks in or near carbonaceous zones on the localization of ore-bodies, have been the main practical results of the studies. Consideration of some of the geological features of the Porcupine area, and of the geology and mining experience of the principal producing mines, has helped toward a perspective of Vipond's ore-finding problems. These features are first discussed. The background and procedure for Vipond mining geology, and the major results of the geological mapping, are then summarized. Then follows a résumé of tangible factors that influenced vein, ore-body, and gold localizations; and, next, explanations of the facts ascertained. Because they were found of little utility, many fascinating problems, such as the origin and mode of emplacement of the veins and lodes(l), the ultimate source of the ore, and the physico-chemical and mechanical agencies affecting vein and ore formation, are treated cursorily or are neglected in these notes.

Jan 1, 1934

By B. R. Conard

Copper refining at Vale Canada (previously known as Inco) has been associated with Ni production. Because Cu and Ni carry risks for adverse health endpoints through inhalation exposure, it is critical that their aerosol levels, and the metallurgical processes through which they enter the air, are understood. Because certain Ni substances have been linked to respiratory cancers, it is also important to characterize the amounts and types of Ni compounds in occupational settings. This paper describes electrorefining and electrowinning operations near Sudbury, Ontario (1930–present), and gives aerosol measurements (1978–present).

Jan 1, 2014

By P. W. Billwiller

Abstract The Britannia Mining and Smelting Company, Limited, have replaced diamond drills with percussion drills and tungsten: carbide bits for most of their blast hole drilling operations and have thereby reduced ore breaking costs. Two-inch Carset bits .are used, with one-inch hexagonal Atlas Chippewa alloy steel in 3-foot .and 6-foot lengths. Locally made couplings of Atlas SPS 245 alloy steel connect the rods. The machines used are 31½-inch automatic leyners with lugged or anvil block chucks. For drilling holes below the horizontal, the lugged machines with special adapter rods made from 114- inch solid round Atlas SPS 245 are required. These rods are lugged at one end and a water hole is drilled for six inches into the other end. Over this rod is placed a water swivel which permits the water or air to be sent directly into the steel. A decreased cost per foot, increased footage per shift, and the use of standard equipment and crews are some of the main advantages of tungsten carbide drilling over diamond drilling. Introduction Long-hole drilling with percussion drills and sectional steel was introduced in several American mines some twenty-five years ago. It did not prove very successful, however, because the rapid gauge loss in steel bits necessitated the use of very large starter bits. This in turn rapidly fatigued the straight carbon-steel then in use, made it difficult to maintain the couplings, and resulted in a slow drilling rate. The introduction of the tungsten carbide insert bit and alloy drill still has changed this picture and opened real possibilities for the application of percussion drills to blast-hole drilling. If this type of bit had been perfected ten years ago, much of the research work and experimenting done to apply diamond drills to ore breaking would have gone toward developing the application of the tungsten carbide bit to this problem.

Jan 1, 1950

By D. W. Heard

Electrospark Deposition (ESD) is a low heat-input, high energy density, micro-welding process. The short pulse duration and high-pulse frequency, in combination with the small amount of material transferred during each pulse, results in the evolution of extremely rapid cooling rates, believed to approach 105-106 °C/s [1]. This rapid solidification event results in the refinement of the microstructure to the nanostructured or amorphous level [2, 3]. Figure 1 displays the resultant microstructure of an Al-17%Si alloy deposited by the ESD process. Furthermore, it was determined that the microstructure of the deposit remained unchanged after subsequent layers were welded onto the presented layer. Freeforming of materials is a rapid prototyping process in which the deposited feedstock is built-up to the desired geometry in a near-net shape manner. Figure 2 displays the automated set-up employed produce three dimensional freeformed objects via multiple deposition trials of the ESD process. The automated XYZ table is equipped with CNC software to transform CAD renderings into three dimensional tool paths. Figure 3 displays an Al-12Si freeformed gear (2" diameter, 12 teeth) produced by the ESD process, prior to removal from the substrate. An SEM analysis of the freeformed component showed that the microstructure did not coarsen during the deposition of subsequent layers during the freeforming process, as depicted in Figure 4, resulting in the production of a bulk nanostructured component. This paper represents a summary of the capabilities of ESD to fabricate advanced materials possessing refined microstructure. In particular, results on the microstructural evolution obtainable for various wear-related systems will be presented. In addition, the feasibility of using the ESD process to freeform three-dimensional objects via multiple deposition passes will be presented and accompanied by a characterization of the properties of the freeformed component. [1] R. N. Johnson, "ElectroSpark Deposition: Principles and Applications," in Society of Vacuum Coaters, 2002, pp. 87-92. [2] J. Milligan, D. W. Heard, and M. Brochu, "Formation of nanostructured weldments in the Al-Si system using electrospark welding," Applied Surface Science, vol. 256, pp. 4009-4016. [3] S. Cadney and M. Brochu, "Formation of amorphous Zr41.2Ti13.8NilOCul2.5Be22.5 coatings via the ElectroSpark Deposition process," Intermetallics, vol. 16, pp. 518-523, 2008.

Jan 1, 2010

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By A. C. Ter-Oganesyants, N. N. Anisimova, G. P. Kotukhova, G. N. Dylko

The process utilized at Norilsk Nickel Polar Circle Division for treating slimes from the electrorefining of copper and nickel was developed in the late nineteen fifties and has survived without any fundamental changes. This technology is a combination of pyro and hydrometallurgical operations to produce PGM concentrates that are sent away for refining. The characteristic feature of the current technology is multiple-stage, extended cycle treatment with significant incomplete production, low labour and automation efficiency and poor hygiene and sanitary conditions. To eliminate all negative aspects mentioned above, specialists of Norilsk Nickel Polar Circle Division have developed a new hydrometallurgical process for treating electrolytic slimes. The main steps of the flow sheet developed are autoclave leaching of the slimes and electrochemical opening-up of a cake from autoclave leaching. The implementation of the new process will allow Norilsk Nickel Polar Circle Division to shorten the process cycle 4-5-fold thus reducing the volume of incomplete production, considerably increase labour efficiency, simultaneously improving working conditions, upgrade the final concentrate, reducing costs and increasing PGM recovery during refining and, ensure higher security of precious metals by employing automated processes and vacuum sealed units.

Jan 1, 2004

By J. J. Mather

NEPHELINE SYENITE is a feldspathic rock resembling granite in texture and hardness but it is white in colour and contains appreciable quantities of the mineral nepheline, the result of a silica deficiency. It is relatively common, with known occurrences in Russia, Scandinavia, India, Canada, United States, and other parts of the world. However, the particular deposit being mined at Nephton, Ontario, by American Nepheline Limited is unique in its remarkable uniformity and low content of iron bearing minerals, both qualities essential in a ceramic raw material. The orebody is a pear-shaped mass over five miles in length, up to a mile in width, rising in three prominent ridges as much as 300 feet above the surrounding lakestudded terrain. American Nepheline holdings, consisting of 2,200 acres, comprise some 85 per cent of the total mass.

Jan 1, 1957

By G Anders

Underground tests of slusher cables at first might seem to be quite simple and inexpensive. They do, however, take a long time and give results that may be ambiguous and unreliable. Also, because underground test conditions are not exactly duplicable, tests carried out at different times or in different mines could not be compared. An attempt was made to develop a laboratory test method that would provide for all factors affecting slusher cable performance underground in such a way as to make it possible to achieve comparable results from different series of tests by exactly duplicating test conditions. Such a method should also make it possible to vary individual factors systematically in order to give a proper assessment of the effect of changing conditions on cable performance. A set of tests, comparing the same two types of cable both underground and in the laboratory, is described. AN assignment at the Algom Nordic mine called for the comparison of two types of %-in. slusher

Jan 1, 1964

By E. Swartzman

"IntroductionGENERALLY, the necessity for mining coals of higher impurity content, the drive for lower costs by intensive mine mechanization, changing market requirements, and the increasing competition of oil and natural gas, have continued to result in an upward rise in coal preparation, and have necessitated a more intensive study of coal preparation problems.Increasing adoption of •continuous mining equipment, for example, is introducing new problems in coal preparation. Limited experimental work in the United States (1) shows that the effect of the continuous miner on size distribution varies with the characteristics of the seam. In some seams, the fines problem is lessened, in others it is greatly aggravated. Generally there is a decrease in the relative amount of the top sizes (plus 2 in.) and a substantial increase in the intermediate sizes (down to about 1/8 in.). Contrary to expected results•, where continuous miners with vertical-moving cutting heads are used, an increase in impurities in the slack sizes does not necessarily occur where draw-slate is taken. This is because the draw-slate tends to be kicked out in lump form. However, if a seam contains bands •and lenses of impurities they are bound to be in the mined product."

Jan 1, 1952

By M. H. Govett, G. J. S. Govett

"The current American ""energy crisis"", occurring in the midst of a global debate on the adequacy of mineral supplies to support present and projected levels of world consumption, has focused attention on Canada as a major world producer of minerals. Exports of minerals account for approximately one-third of Canadian foreign earnings; more than half of these exports are to the United States. Although the United States is a net importer of most industrially important metals, with the exception of nickel and zinc, only a small part of American mineral imports are from Canada; these imports are minerals for which geographical proximity and strategic considerations are important. In the short-term, Canada is more dependent on her exports to the U.S. than America is on imports from Canada. It is argued that Canada, far from indulging in economic nationalism to preserve her resources, should expand her exports while the markets are available."

Jan 1, 1973

By STEPHEN V. FORGERON

The Loch Lamond celestite properties in central Cape Breton Island were mined by Kaiser Celestite Mining Limited from 1970 until 1976. Poor market conditions in J976forced operations to cease. Kaiser holdings included the Lake Enon, MacRae and A mac prospects. A total of about 272,000 tonnes of raw celestite have been mined. Celestite deposits are situated in the Loch Lamond Basin, specifically in Lower Windsor sedimentary rocks. Of the five formations in the Lower Windsor Group, celestite is found in the upper four. Celestite in the Enon Formation occasionally replaces shale that separates stromatolitic dolomite columns; elsewhere in the formation it occurs in association with siltstone and gypsum. Jn the B2 Limestone Formation celestite fills pores or grades between limestone and gypsum. It replaces both limestone and silty limestone conglomerate in the Loch Lamond Formation; this limestone is of unusually high grade (60 to 70% SrSO,J for the area. Evidence indicates that the Uist Formation may hold important celestite reserves. Original celestite mineralization probably resulted from evaporation of seawater on mudflats or 'sabkhas'. Secondary mineralization also may have occurred. Strontium ions could have been leached from pre-existing concentrations and overlying gypsum, moved downdip in groundwater and combined with sulphate rich waters to deposit as celestite in porous B2 limestones.

Jan 1, 1984

By B. K. Bhattacharyya, Morley. L. W.

"The primary purpose of conducting aeromagnetic surveys in mineral areas, and interpreting the data thus obtained, is to aid in the extrapolation of the geology from known to unknown areas-both in a horizontal and vertical direction. This paper describes one of the steps in the process of interpretation which has, in the past, been neglected-that of mathematically or quantitatively treating the data in two-dimensional map form. For this, several techniques are available.These techniques determine the downward and up-ward continuation fields, the second vertical derivatives and the fields reduced to the pole from the total magnetic field data. Second vertical derivatives and downward continuation fields increase the resolution and sharpness in the observed magnetic anomalies and tend to outline the surface traces of causative bodies with a reasonable amount of success in most cases. The 'reduction to the pole' is a mathematical process of calculating the field at the north pole from the observed field so that the un-desirable effects of the dip and declination of the earth's field and of rock magnetization are eliminated.New and accurate means of carrying out these calculations have been developed by the Geological Survey of Canada. In this paper are also presented the results of a method for obtaining the symbol and numerical map of the processed data with the help of the printer associated with the computer. The tedious work of digitizing magnetic field values in a map can be speeded up by the use of a semi-automatic coordinatograph, with the aid of which field values can be accurately transferred to punched cards."

Jan 1, 1966