Search Documents

By B. Arsenault

Aluminum coatings can provide galvanic cathodic protection for several metals and alloys, In order to be a suitable protective solution on structural components, the mechanical integrity of the component must be preserved, In particular, fatigue properties are a challenge for thermal-spray protective coatings on mechanical structures, To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc-sprayed protective coating, different surface preparations prior to arc spraying were considered, In the present work, a feasibility study was performed using laser ablation as a surface-preparation technique before or during arc spraying of coatings, This was collaborative effort between the LERMPS laboratory in France, the National Research Council Canada and the Royal Military College of Canada, Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate-surface-preparation techniques including laser ablation (Protal® process), grit blasting and shot peening. Results indicate that a combination of key conditions, including the use of nitrogen as the arc spray gas, shot peening, and proper laser energy density for ablation, provide high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates.

Jan 1, 2005

By Peter Chmara

The measurement of dust concentration in Ontario mines since 1926 has been accomplished by konimetry, based on South African experience and methods. The introduction of a voluntary program of semi-annual surveys of air conditions at all operations throughout Ontario mines created a need for an instrument that would assess konimeter spots rapidly and accurately. The development of the Electronic Scanner, it is felt, answers this need. A program whereby all konimeter spot samples taken at Ontario mines will be counted at the MAP AO field offices in North Bay is described.

Jan 1, 1969

By L. Lorio, B. Hilscher, P. Nayak, N. Yoon

"Mining has been a staple to technological advancement ever since the dawn of time. By harnessing the different physical and chemical properties that each mining commodity brings to the table, more and more innovation is developed and manufactured. As these non-renewable resources continue to be extracted, the industry as a whole faces a challenge in finding the next economical deposit as well as declining grade at the current operations. By means of pre-concentration, ore sorting aims to separate the barren material from the valuable ore to reduce energy consumption and tailings generation, while increasing the feed grade, concentrate grade, mill recovery, and revenue. In addition, ore sorting allows the modification of deposit geometallurgy in order to allow the creation of an optimal mill feed. This paper evaluates the applicability and challenges of ore sorting by utilizing the results from four different mines, and reviews them in detail. The mines include one underground and three open pit mines that are precious metal operations. In order to understand the applicability of ore sorting in these operations, initial rock-by-rock test results and different types of assays (atomic adsorption [AA], inductively coupled plasma [ICP], and fire assay) are utilized. Using the assay results, the grade recovery curves for ore sorting are generated and they are further improved by using and developing an ore sorting algorithm, which is discussed in this paper. The application and evaluation of ore sorting in greenfield and brownfield properties will also be discussed. The state of the art ore sorting technologies for both rock-by-rock and bulk sorting are also reviewed in this paper. The future technologies on the horizon, including different combinations of sensors, are explained. The sorting technologies include X-ray transmission (XRT), X-ray fluorescence (XRF), colour, infrared, electromagnetic, and laser induced breakdown spectroscopy (LIBS)."

Jan 1, 2017

By M. K. Aly

"ABSTRACTThis paper briefly describes the mining method proposed for the iron ore deposits in Wadi Shatti, western Libya. The iron ore produced will be used in the steel plant at Misurata on the Mediterranean coast. GeologyThe Wadi Shatti is located in the central part of western Libya. Flat iron-bearing sedimentary rocks are exposed with remarkable regularity in this valley. It occupies an area 200 km long by approximately 20 km wide trending in an eastnortheast direction between Jabal Fazzan in the north and Zel1af Sand Dunes in the south (Fig. I). Only a part of this valley has been ful1y explored by drilling on a 400- by 200-m pattern in an area of 18 km2 south of the town of Taroot. Farther to the south, no exploration by drilling can be done due to the presence of sand dunes .The iron-bearing bed is about 10to 15m thick, with a dip of 2 to 4 degrees in a southerly direction . The overburden consists mainly of clayey sandstones, 4 to 5 m thick, in the northern part, increasing to 35 m in the southern part. The iron ore bed consists of three different layers, from the floor upward: (1) Lower Reduced Ore (LRO), having a varying thickness of 1 to 7 m; (2) Magnetic Ore (MO), with a thickness varying from 4 to 12 m mainly in the central part of the area; and(3) Upper Reduced Ore (URO), with a bed thickness varying from 0 to 7 m."

Jan 1, 1980

By I. Farr, M. R. Mock, J. C. Robison

"HPAL and POX autoclave vapor-space gasses are vented through an autoclave PCV (Pressure Control Valve). The downstream steam-born mist of liquid droplets and solid particles travels in excess of 1000 m/s with megawatts of kinetic power at temperatures up to 160 C. The characteristics of downstream states often result in problems with corrosion, erosion, noise and vibration. Comprehension of those and related characteristics aids in improved pressure control, overpressure control and autoclave level control. We introduce compressible multiphase flow concepts and constructs germane to such flow including choked flow, continuous phase change, shock waves and supersonic flow plumes. Flow modeling based on first principles quantitatively predicts such flows providing a tool for component sizing and a method to estimate effects of water injection on flow. Insight deduced from modeling aids in mitigation of afore mentioned problems of which we share some from-site examples.INTRODUCTION First principles related to fluid thermodynamics and compressible flow have been employed akin to their application in the rocket industry. We will present the results of the application of those principles conceptually and authentically without mathematical rigour while using language of the pertinent disciplines. The autoclave (AC) vapor space over the slurry of a POX (Pressure Oxidation) or HPAL (High-Pressure Acid Leach) system (depicted in Figure 1) is vented via a PCV (pressure control valve) followed by certain ducting, and perhaps a nozzle, before exiting at atmospheric (typically) pressure. As indicated by its name the PCV controls the AC pressure as the flow control component of a pressure control loop."

Jan 1, 2017

By R. D. Browns

In his Budget Speech on March 31, 1 977, the Honourable Donald S. Macdonald expressed concern about the financing of investments through new equity issues. He mentioned the need to render more attractive participation in the equity market by investors in all in come brackets. One of the measures introduced in the budget to accomplish this goal is the proposal to increase the dividend gross-up and tax credit in respect of most dividends received by an individual from Canadian companies. The following comments and tables serve to illustrate the impact of this particular proposal.

Jan 1, 1977

By E. Yan, M. Mankosa, E. Wasmund

"Rougher flotation in sulfide ore applications is typically performed using conventional flotation machines. The trend over the last 100 years has been for these cells to become larger in volume with cells reaching sizes of 600 m3 and in some cases even larger. The associated foundation loadings, transport and installation requirements along with building size have also increased. In an economic environment where projects must be executed with dwindling capital supply, bigger is not always better. More recently, industry is being challenged to identify new technology that allows for improved flowsheets and financial returns through efficiency gains. To meet this challenge, a novel high-intensity two-stage flotation system known as the StackCell™ was tested to potentially achieve installation volume and required retention time gains when compared to conventional flotation circuits. The results from on-site pilot scale work conducted on typical copper concentrator rougher flotation feed showed retention time gains on the order of 6 to 9 times when compared with conventional flotation equipment. This finding has the potential of reducing capital demands for rougher flotation circuit designs when incorporating the StackCell. The results from test work will be discussed in this paper showing comparative test data generated with a Denver bench batch test, pilot StackCell and large conventional cells, all receiving the same feed.INTRODUCTION Over the last few years, a number of flotation devices have been described as two-stage or multi-stage flotation units. The idea behind multi-stage flotation devices is that flotation performance can be improved by utilizing cells with multiple specialized units in series, but not all units of the same type, as is practiced in trains of multiple tank cells or columns. Instead, each unit is specially designed to provide the optimized fluid environment for each stage of the sequential flotation process. This idea has been proposed based on a study of the fundamentals of the flotation process, and the realization that the process consists of discrete sequential processes, that are each optimized with dissimilar process conditions (Finch et al, 1995), (Zhou, 1996). Instead of executing each step simultaneously in a homogeneous fluid environment, where the conditions would be a compromise between particle collection and froth recovery, the multi-stage flotation unit operates in a set of segregated process environments, each with a set of conditions optimized for that step."

Jan 1, 2018

By Joseph Daniels

When Dame Nature shook her horn of plenty and distributed her bounties over the face of the earth, she blessed the Pacific coast with many riches, but with these she added many offsetting disadvantages or handicaps, designed, no doubt, to effect a proper balance between wealth and economy. Nowhere is the application of the law of compensation more aptly illustrated than in the matter of fuel and power resources. A glance at the map of the Pacific northwest will show that west of the Coast Range batholith we are bounteously supplied with coal, with timber, with water power, and with tributary resources of oil from California. Alaska, British Columbia, Washington, all contain large resources of coal; Oregon and California to a lesser degree, but, compensating the golden state for its deficiency in this respect, oil was placed in the treasure ,chest. Timber, of wide variety and in lavish quantity, covers the forests from tidewater to mountain slope, and within this protected watershed area flow streams which give the Pacific coast states the largest single share of the potential water-power resources of the country. Something over 40 per cent. of the total estimated horsepower of the United States is to be found in the Pacific states, and British Columbia has 15 per cent. of the total for Canada; but of this total less than 10 per cent. has been developed.

Jan 1, 1924

By J. Drelich

We report structural forces measured for 10 nm silica particles deposited on alumina substrate and 5-80 nm alumina particles on mica using atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of the nanoparticles used. Additionally, selected force-separation results indicate that the forces involved between the AFM probe and individual nanoparticles can be studied using the nanoparticle-coated substrates.

Jan 1, 2006

By B. Haneman, J. A. Gorst, W. Slabbert

"The Bayer process involves the digestion of bauxite in caustic liquors at high temperature and pressure. Typically the digestion section of the plant involves the heating of liquors up to the digestion temperature followed by flashing of the digestion product to atmospheric pressure with the flashed steam used to pre-heat the incoming cold slurry. Despite the heat recovery, the digestion process is a high consumer of energy. The application of tube digestion technology in such plants has resulted in significant improvements in refinery energy efficiency with associated benefits of process simplification and refinery flow sheet capital cost reduction. This paper reviews the potential application of this technology to other metals within the non-ferrous industry.THE BAYER PROCESSA typical Bayer flow sheet is shown in Figure 1. The raw feed material bauxite (containing aluminium hydroxide as gibbsite Al(OH)3 and boehmite AlO(OH)) is digested in caustic liquors (caustic soda is the solvent) at high temperature and pressure. This process extracts the alumina and silica and any carbon present on the ore. The slurry is then flashed down to atmospheric condition allowing for heat recovery from the flashed vapour and producing slurry supersaturated in alumina.Following the digestion process the mud is removed via thickening and then pressure filtration to remove fine particulate and produce a clarified liquor with dissolved alumina in solution. The resulting pregnant liquor is then cooled allowing the alumina in solution to precipitate as aluminium trihydrate Al(OH)3. The precipitated hydrate is then filtered and washed and classified into fine and coarse fractions. The fine material is returned to the precipitation process as seed while the coarse fraction is calcined at high temperature to produce alumina. The filtrate from the filtration process (spent liquor) is then heated by the incoming pregnant liquor before being fed to an evaporation process which produced the strong caustic liquor required in the digestion process. Finally, the mud from the thickening process is washed to recover caustic and then fed to tailings ponds. The washer overflow is then mixed with the digester product to increase super-saturation."

Jan 1, 2012

By P. K. Kaiser

3-D virtual reality (VR) visualization has opened new opportunities for complex 3D (x, y, z), 4D (x, y, z, t) or even nD data interpretation. The integration of common earth models (3D geologic data), mine models (3D excavations and stress), extraction models (1D time sequencing or mine sequencing) and nD monitoring data (e.g., seismic event parameters) into a common mining process model provides a platform for experts in various fields to better design, evaluate, monitor and modify mine plans throughout a mine?s life; from feasibility, through operation, to closure. Viewing seismic data in a stereoscopic VR environment within a mining process model offers data interpretation processes previously unavailable at lower dimensionality. MIRARCO has developed data analysis and viewing processes specifically designed to enhance microseismic and seismic data interpretation in a collaborative, immersive VR environment; bringing mine personnel and expert consultants together to evaluate data and make strategic decisions for cost effective and safe mining. Seismic events cause immediate hazards (rockbursts) and microseismicity causes gradual hazards through its cumulative effect in rockmass degradation. The focus of this paper is on understanding seismicity from a mine safety and mine planning perspective; in particular, how seismic migration patterns relate to the rockmass response to mining. The benefits of innovation in seismic data interpretation are significant, e.g., for hazardous work area identification, allowing better formulation of re-entry policies and workforce allocation planning, as well as allocation of effective support systems to strategic areas of elevated risk. Better understanding of the overall response of a mine to extraction also facilitates mine planning and design, assisting in reducing production costs and thus in enhancing profitability.

Apr 1, 2005

By P. W. A. Mayer

"As the push toward the northern regions of Canada steadily increases to exploit the rich mineral reserves, interest is steadily rising in respect to accessibility and climatic conditions and the problems posed thereby. In twelve years of operation, the Iron Ore Company of Canada, and associated companies, have found, through advanced technology, ingenuity and, most of all. need, some of the answers to the running of a profitable year-round open-pit mining operation."

Jan 1, 1966

By R. A. Kipp

THE dry concentration of ores and minerals is a subject on which there is very little engineering literature available. With the advent of flotation, practically all milling research was turned to this development as it held the answer to large-scale economic operations. However, there are many concentration problems that can be more adequately and economically handled by the dry methods that have been developed, and, consequently, I believe it is very advisable for mining men to become fully 'conversant with just what can be done in the dry state. Therefore, today, I should like to give a brief summary of the processes that are available and, in a general way, how they can be a p-p lied. I shall confine my remarks mainly to two dry processes: THE Am FLOTA'l'ION TABLE AND THE ELECTROSTATIC SEPARATOR Dry Magnetic Separators should probably also be included, but I am

Jan 1, 1961

By A. Khan, C. Ciriello

The purpose of this paper is to demonstrate the value of constraint modelling in optimization of mineral processing systems. This will be achieved by first understanding the overall concept of variation and constraints present in any system. Next, the value of using a Constraint Model in optimization is demonstrated through comparison of business cases. The benefit of understanding the severity of constraints and movement of the bottleneck within a mineral processing system will be understood through the use of a case study. Paper will conclude with a summary of all optimization benefits that utilization of a constraint model can bring.

Jan 1, 2015

By Loui Geoffroy, Philippe Gaultier, Martin Piotte, Claude Coache, André Drouin

"Automatic driving at high speed of an underground truck was tested at Brunswick mine in September 1995. Modifications to the truck included: a remote interface to control actuators, front and back video cameras to follow a roof mounted optical guide and proportional hydraulic controls on the steering.The mathematical model of the hydraulic system was adjusted using least square regression. The steering data, used in calculating the regression parameters, were acquired from the moving truck. The automatic steering control used three measured variables: lateral deviation, angular deviation and steering angle. Lateral deviations are obtained using the cameras, which are in continuous view of the guide, while steering angles are acquired from an extensiometer placed at the articulation point of the vehicle. Gain scheduling was used to compensate for vehicle speed and available hydraulic flow. Non-linear characteristics of the modeled hydraulic system were offset using open loop compensation.Speeds up to 23 km/h in forward direction and 13 km/h in reverse were achieved deviaduring continuous testing along one of the mine’s production drifts. Proportional steering was essential in achieving high speeds, as it enabled more precise positioning of the vehicle’s steering direction while reducing the abuses on cylinder and cylinder pins via diminished oscillations about the optical guide at high speeds."

Jan 1, 1997

By J. Ouellet

"ABSTRACTA brief background on in-situ testing of mine backfill, as well as pressuremeter testing is briefly described, and results from an in-situ testing on paste backfill are presented. A series of self-boring pressuremeter tests were done from the top of a backfilled stope in an underground mine. The tests were conducted along a 20-metre vertical line in the centre of the stope. Some 14 tests were performed along this depth. The instrument used was a Camkometer built by Cam Insitu, Cambridge. The instrument proved to be efficient and reliable for underground testing in a cemented paste backfill. The testing program was conducted within the planned schedule with a high success rate. The test done in this study permitted the measurement of paste backfill strength, stiffness and in-situ horizontal stress within the backfill. RésuméUn bref historique des essais in situ dans le remblai minier est présenté. L’essai pressiométrique est décrit succinctement et des résultats d’une campagne d’essai dans un remblai en pâte sont présentés. Un programme d’essais au pressiomètre auto-foreur a été réalisé à partir du sommet d’un chantier remblayé sous terre. Les essais ont été réalisés le long d’un ligne vertical d’environ 20 mètres pour un total de 14 mesures. Le Camkometer de la firme Cam Insitu de Cambridge a été utilisé. Cet instrument s’est avéré efficace et fiable pour tester le remblai en pâte cimenté sous terre. Le programme d’essai s’est déroulé à l’intérieur de l’échéancier prévu avec un taux de réussite élevé. Ces essais ont permis de déterminer la résistance, la rigidité de ce remblai ainsi que les pressions in-situ prévalant dans le remblai."

Jan 1, 2000

By C. J. Hall

This paper presents a basic motive column analysis of natural ventilation and shaft resistance, using the density depth diagram. The method makes use of tables showing the state of the air as determined by thermodynamic analysis. Several theoretical examples are given.

Jan 1, 1968

By Daan Maijer, Wade Marquardt, Robert MacKay, Steven Cockcroft, Farzaneh Farhang Mehr

"To comply with the new Corporate Average Fuel Economy (CAFE) standards, the automotive industry is aiming to reduce weight and increase the power and efficiency of small displacement engines through the application of forced induction technologies. As an example, there are now several 2.0 litre turbocharged engines in production, producing in excess of 240 hp. To meet the need for improved fatigue properties in the engine blocks used in these high-output engines, a new water-cooled chill technology is under exploration at UBC in partnership with General Motors and Nemak. A series of experimental techniques were used to assess the capability of the new chill to extract heat from an A319 casting in the vicinity of the main bearing bulk head. The results show that this method has the potential to achieve a reduction in secondary dendrite arm spacing thus meeting the new microstructural specifications for these engines.INTRODUCTION The automotive industry is working to meet the stricter efficiency requirements laid out within the CAFE (Corporate Average Fuel Economy) regulations (Bastani, 2012; Cole, 1995; Mackay, 2011; Miller, 2000), while at the same time not sacrificing performance. One approach is to increase the use of lightweight materials, which leads to a decrease in the overall vehicle weight and fuel consumption (Cole, 1995; Mackay, 2011; Miller, 2000). Other approaches include smaller displacement engines and gas-electric hybrid drivetrains. However, one trend that is becoming clear, is a greater emphasis on force induction gasoline engines. This allows for weight reduction to be achieved with smaller displacement engines without sacrificing performance. One consequence of this approach is that the engine block materials are subject to higher in-service thermal and mechanical cyclic loads (Cole, 1995; Miller, 2011; Heysler, 2001) The fatigue properties of an alloy are strongly affected by a number of the, as-cast, microstructure features including, Secondary Dendrite Arm Spacing (SDAS), porosity and eutectic lamella spacing (including intermetallic ß-Al5FeSi platelets) (Mackay, 2010a; Mackay, 2010b; Viet-Duc, 2015; Casellas, 2005). It is generally accepted they can act as fatigue initiation sites and that a reduction in their size will result in an improvement in fatigue performance. For a given alloy chemistry, one of the key parameters affecting the length scale of all three is cooling rate (Mackay, 2000)."

Jan 1, 2017

By B. R. Hart, S. S. Dimov, J. Fournier

Carbonaceous matter (c-matter) in sulphide ores can adversely affect the process of gold recovery during cyanidation due to its ability to adsorb, or preg-rob, gold from a cyanide leach solution. This paper describes a standardized procedure for characterization of c-matter in an ore sample providing detailed information on its composition, maturity and preg-robbing capacity. The procedure utilizes the following complementary analytical techniques in conjunction with several chemical tests and assays: SEM/EDX Raman spectroscopy and TOF-SIMS. Results of the test can be used as a predictive tool to estimate the impact the c-matter will have on the gold recovery process. A comparison between predicted preg-robbing behaviour and cyanidation test results are presented.

Jan 1, 2011

By John A. C. Fortescue

There is a need for better communication between scientists who plan and carry out mineral exploration research in glacial terrain and the exploration geologists who look for mines. In this paper, four ways in which workshops could be used to close this communication gap are described and discussed in relation to the solution of this problem in Canada.

Jan 1, 1973