Search Documents

By W. G. Spencer, E. Sulis, P. M. Tiley

"Dome Mine's No.8 shaft is located about 1 km northeast of Dome's No.3 shaft and mill complex in South Porcupine, Ontario.No.8 shaft was brought into production in 1984 to hoist ore and waste for the complete mine as well as to service the mine from the 1600 level and below. Access above 1600 level is provided by No. 3 shaft.The rectangular shaft has six compartments consisting of two skips, a cage, counterweight, manway, and a service compartment. The over-all size of the shaft is 14 ft 7 in. by 20 ft by 7 in. (Fig. 1). A 7th compartment for shaft deepening is incorporated in the bottom 500 ft of shaft. The shaft is 5470 ft deep. The loading pocket is located at 5300 ft and the dump 61 ft below the collar.Surface facilities consist of a concrete headframe and a structural steel hoistroom which houses the cage and production hoists . The service hoist is a 12-ft diameter double drum, with one 1750 HP DC motor, and the production hoist is a 15-ft diameter double drum with twin 1750 HP DC motors.Both hoists have a single clutch and a single reduction gear train built by Orenstein & Koppel, and equipped with Canadian General Electric drives. The cage hoist is equipped with a disc pinion brake.The skips were originally aluminum 14-ton capacity, Rolla-chute design with steel liners on three sides and 4 in. of rubber on the back, to absorb the loading impact. The original guide rollers consisted of fixed 10 in. pneumatic tires. The face-to-face units were eventually replaced with larger airplane-type tires mounted on a spring loaded pivot arm."

Jan 1, 1993

By David A. Grieve, David E. Pearson

"A rank-map of Crowsnest coalfield, showing the distribution of the bituminous coal measures and the locations of major structures, has been produced from vitrinite reflectance measurements on over600coal samples. The timing of coalification in relation to these major structures has also been determined.In the west-central portion of the coalfield a complete stratigraphic succession of coal measures which rides on major thrust surf aces is all of high-volatile bituminous rank, but despite the structural discordance no break in rank is discernible across these structures. The thrust faults therefore predate much of the coalification.Three major valleys expose cross sections of the folded coal measures and in each an increase invitrinite reflectance is demonstrable as individual seams are traced from ridge crest to valley floor. Thus, in these sections, a significant amount of coalification post-dates folding. The proportion of this post-folding coalification is found to increase toward the south of the coalfield.A late gravity-fault, exposed along the east crop of the coalfield, places high-volatile coal-bearing successions in contact with low-volatile coal and demonstrably is a reactivated thrust fault. Coalification at this locality occurred between these two different ages of faulting.The variations in rank and the subtleties of the coalification pattern have, together with systematic changes in the maceral composition of coal seams, had a profound effect on coal quality in the coalfield. Coking coals with a variety of properties occur together with some coals that have no caking capacity."

Jan 1, 1985

By Etienne Roy Grégoire

Since the early 1990s, the Canadian mining industry has been increasingly defined by the signing of Impact and Benefit Agreements (IBAs) between mining companies and Aboriginal peoples. While these agreements are intended to complement the legal system, they also serve to establish the legitimacy of mining projects and to encourage the harmonious integration of these projects into their social and environmental contexts. Beyond their practical implications, what are the effects of such agreements on the ability of Aboriginal communities to access the institutional space where the authorization of mining projects and the conditions of their implementation are decided? Can we view IBAs as a preliminary step towards the operationalization of the principle of Free, Prior and Informed Consent? This paper aims to explore the potential of IBAs as a sustainable solution to the legitimacy issues that result from the implementation of the formal regulatory framework governing mining activities in this jurisdiction. We highlight what constraints and opportunities the James Bay and Northern Quebec Agreement (JBNQA) engenders for local communities and draw attention to the ways in which the negotiation of the Raglan IBA and the environmental evaluation processes act upon each other. We find that certain structural problems - and problems of legitimacy ? related to mining in Northern Quebec cannot be solved by the sole signature of an IBA, which suggests the need for caution when considering such agreements as a panacea. The Raglan case demonstrates that IBAs, like other modes of regulation relying on the direct interface between companies and communities, would benefit from a stricter framework and more explicit ties with official regulation channels.

Aug 1, 2013

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012

By G. Macfarlane

"In 1985, a crushing plant, located in the feed preparation area of Kidd Creek's copper smelter, was modified. The plant, which originally had treated only copper-bearing materials for the smeller, at a rate of 10 tonnes per hour, was expanded to 40 tonnes per hour capacity and modified to treat silica ores to meet the smelter’s flux requirement and also gold ores from the company's Hoyle Pond property. In the storage area adjacent to the crushing plant a 300 tonne per day gold mill was constructed.This paper outlines the construction and first year of operation of the crushing plant and gold mill with emphasis placed on the capital and operating advantages to be gained by utilizing an existing metallurgical infrastructure.IntroductionThe Kidd Creek Mines Ltd. copper-zinc-silver orebody is located 24 km north of Timmins, in Northern Ontario . Mining of this massive sulphide de posit commenced in 1966 and, in the ensuing years, a concentrator and zinc plant were constructed at the metallurgical complex, approximately 17 km by rail from the mine site . At this same site, in 1981, a copper smelter and refinery were commissioned. The smelter which utilizes the Mitsubishi smelting process for the continuous production of blister copper from copper concentrate, has been comprehensively described in previous papers.At the time of the smelter construction, a small (10 tonnes per hour) crushing plant was installed in the smelter's feed preparation area. This plant was used to treat the copper-bearing revert material produced by the smelter, and, apart from periods when slags and matte were produced through furnace drainage at the end of each operating campaign, it was generally under-utilized. This fact, together with the requirement to devise a more cost effective method of providing silica flux for the smelting operation, was the basic rationale for modifying and expanding and crushing plan t. At the same time, development at Kidd's Hoyle Pond orebody had progressed to such a stage that a gold mill of 300 tonnes per day was warranted."

Jan 1, 1988

By M. H. Moys, C. Bhondayi, Eric Tshibwabwa

"The relationship between froth bubble size as represented by intra-bubble impact distances (IID) and flotation performance is investigated. Experiments using an artificial ore comprising of limestone as the floatable component and silica as the gangue material were carried out in pseudo-steady-state circuit. A method to measure IIDs developed by Bhondayi and Moys (2014) was then used to measure froth bubble sizes as a function of froth height, superficial gas velocity and feed rate (pulp residence time). Samples for flotation performance evaluation were also taken. Results indicate that as froth height increases, the average IID values increase resulting in a decrease in limestone recovery while the grade increases. Increasing gas rate results in lower IID values that are accompanied by high recovery and low limestone grade. The effect of feed rate on both flotation performance and average IID values depended on froth depth and gas rate. Average IIDs largely remained the same at the two feed rates investigated.INTRODUCTIONIt is regarded as obvious that froth bubble size distribution (FBSD) will have an effect on plant grade and recovery. As the average FBSD decreases, the bubble surface area flux will increase making possible an increase in recovery and a decrease in grade. The opposite trend will be involved if average FBSD is increased. However: no method for measuring FBSD has been available, so these trends have not been studied in any detail. Bhondayi and Moys (2014) developed a novel technique to measure or estimate froth bubble sizes. Although they established a potential to use this method in understanding froth performance, no data have been presented to assess the correlation between the estimates of bubble sizes and actual flotation performance. In this work experiments are done to establish how the change in froth phase bubble sizes affect flotation performance. Flotation performance will be evaluated using recovery and grade. How water recovery to the concentrate changes with changes in bubble sizes will also be evaluated. It is known that water recovery is approximately inversely proportional to the square of the overflowing bubbles sizes. It will be interesting to establish how the rate of change of bubble sizes changes with water recovery."

Jan 1, 2016

By M. Beech-Jones

The increased emphasis on the efficient utilization of capital and mineral resources has led to several new advances in the science of mineral separation. One example of a recent development is the application of high-capacity high-intensity wet magnetic separators to fine hematit e recovery by a leading Canadian iron ore producer. The iron ore recovery feasibilit , flow-sheet development, circuit operation and metallurgical performance are reviewed.

Jan 1, 1979

By R. W. Boyle, W. Dyck

"Scientists throughout the world have observed radioactive disequilibrium in the uranium decay series. Radiometric and fluorometric determinations of U in plants from the Goldfields district and in sediments and rocks from the Beaverlodge district exhibit marked radioactive disequilibrium. The eU/U ratio in plants rooted in mineralized ground shifts from greater than unity to less than unity for those rooted in background soils. A similar shift is observed in the transition from rocks to stream sediments and to lake sediments in the Beaverlodge district.Results of a Rn-Ra-U survey of lake bottoms in the Key Lake district show that anomalous hydromorphic U from U mineralization is parallelled by anomalous Rn, even though there is much less Ra in the lake-bottom sediments than one would expect from the amount of U present. IntroductionDisequilibrium in the U decay series has been studied for many years and is observed in almost all surficial environments. Rosholt (1959) measured U, 234Pa, 23O'fh, 226Ra, 222Rn, and 210Pb in a large number of U ores and outlined six types of situations to explain disequilibrium. Davy (1974) outlines the geological significance of radioactive disequilibrium situations with respect to exploration. Levinson and Coetzee (1978) discuss possible mechanisms by which separations of parent and daughter elements are affected and suggest analytical pitfalls that may be encountered in the use of radiometric techniques when disequilibrium has occurred. Generally, it is the oxyphile and easily complexed parent 238U (with its associated isotopes 235 U and 234U) that is leached from rocks and soils at a faster rate than are the daughters, 230Th, 226Ra, 2loPb, and 206Pb. This mobilized U is adsorbed on sediments in streams and lakes, or enters groundwaters, where it is eventually precipitated under reducing conditions, occasionally in oregrade concentrations. This surface leaching and"

Jan 1, 1980

By P. Farsangi, A. Hara

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill on a daily basis. Consolidated rockfill is comprised of sized aggregate mixed with different ratio and amounts of binders. Consolidated rockfill, with closely controlled specification, is employed for subsequent pillar recovery and improved passive active/ ground support. With the same amount of cementing agents consolidated rockfill mass yields a higher, compressive strength, modulus of elasticity, cohesion, and angle of friction compared to a typical cemented hydraulic fill mass.The consolidated rockfill at Kidd Creek Mines is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars.The quality control of materials used in Kidd Creek's rockfill system could be effected in three stages of handling: (1) at the surface backfill plant; (2) during transportation; and (3) placement of the fill.The emphasis in this paper is placed on individual stope backfill design and quality control measures at Kidd Creek Mines to place fill in large-scale open stopes which eventually could be exposed on all four walls during pillar recoveries."

Jan 1, 1993

By G. Pouskouleli, T. A. Wheat

"The role and benefits of using statistical methodology in the development and optimization of materials and processes is examined. It is shown that considerable benefits accrue from the use of an appropriate design in which a number of factors (process parameters) are varied simultaneously while the system response such as percent recovery, degree of separation, purity, etc. is monitored and ultimately optimized.Compared with the commonly encountered one-factor-at-a time approach, this schema exploits reduced experimentation (thereby requiring reduced resources [staff, time, dollars, etc.]) yet yields quantitative information on the significance of each factor and their combinations on the measured response."

Jan 1, 1992

By Y. P. Wu

Steeply dipping seam refers to the coal seam with dipping angle in the range of 35?55°, which is well recognized to be very hard to mine by the mining industry all the world. In the last two decades, some fundamental researches were focused on the strata behavior of long-wall panel, complicated rock mass breaking process of the steeply dipping seam, overburden stress field developing and evolution, rock strata breaking and moving process, rock structure stability mechanism and control. Results show that it?s presenting macro stress arch-shell (MSAS) of the stress distribution of the overlying rock in steeply dipping seam. The MSAS is the spatial distribution of intensity envelope line under the strength criterion and has the geometry shape asymmetry as well as the stress distribution heterogeneity. The arch- shell base will forward as the working face mine forward and the shell roof will extend to higher overlying strata above the gob. In this paper, the stress arch-shell analysis model and coordinate system were established and analyzed the inclined masonry structure at different zone. Analysis results show that the rock damage at the key part of the arch-shell is the main factor which causes whole overlying rock structure failure. The rock structure instability modes have tension instability of the shell roof, compression-shear instability of the shell shoulder and composite instability of the shell base, meantime, instability coefficient is proposed to determine instability condition. The above research results enrich the complex coal seams mining theory and provide a theoretical basis for mining safely and efficiently in steeply dipping seam.

Aug 1, 2013

By Simon Hanner

November 2005 Memorial University Newfoundland and Labrador Mines and Energy Review of Activities Exploration and Mining New Brunswick ?Université du Québec a Montréal McGill University 2005 Manitoba Mining and Minerals Convention Université Laval Quebec Exploration 2005 Saskatchewan Open House December 2005 University of Calgary University of Alberta 'Laurentian University 'Queen's University 'University of Toronto 'Ontario Prospectors Association January 2006 Mineral Exploration Roundup, BC March 2006 Prospectors and Developers Association of Canada Convention April 2006 University of Ottawa Carleton University

May 1, 2006

By H. D. S. Miller

"This paper introduces a new approach for the design of rib pillars. The approach involves an empirical method for pillar design and a discussion of the pillar stability used for open stope mining methods.The empirical method predicts the degree of stability of rib pillars. Pillar load is estimated using two and three dimensional numerical modelling. Rock strength and the shape effect of pillars are used to account for pillar strength. The method has been calibrated with case histories from Canadian open stope metal mines and is compared with other methods used [or pillar design.INTRODUCTIONThe role of rib pillars in open stope mining is to provide stability to a mining block by limiting rock mass displacements and restricting the exposure of a rock mass in stope backs and stope walls. They also provide flexibility in ore extraction by dividing a stope block into multiple working faces.The use of backfill in open stope mining methods has reduced somewhat the need for optimum pillar design. In contrast to permanent pillar methods, the dimensions do not need to be minimized because the pillars are usually recovered in a later stage of mining. However, the consequences of poor pillar design are often overlooked and can still be severe. A pillar that does not perform its intended role may result in excessive stope or pillar sloughing, difficult and expensive pillar recovery, loss of permanent access and remedial costs such as development rehabilitation, artificial support or low productivity.Pillar design concepts of the past were not developed for open stope mining conditions and generally have not been confirmed for open stoping. The focus of this paper is to introduce an empirical design relationship specifically for open stope pillars. It provides a stable, yielding or failed pillar assessment for a given design."

Jan 1, 1989

By S. Yannacopoulos, L. Bichler, P. Wanjara, J. Gholipour

Characterization of a virgin and in-service Inconel 718 alloy was undertaken to study the changes caused by the service conditions on the grain size, ?? phase, MN-type nitrides and MC-type carbides. The size, distribution and volume fraction of these phases and grain size were studied using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and electron backscattered diffraction (EBSD) analyses. A considerable difference in the grain size, as well as distribution and volume fraction of the precipitates was observed in the in-service material as compared to the virgin Inconel 718. As a result of these microstructural changes, a notable dissimilarity in hardness between the materials investigated was observed. The results presented in this study are important for proper development of repair parameters and heat treatment of in-service Inconel 718 material.

Jan 1, 2014

This paper examines the latest advances in mine hoist motor and drives systems. The technology employed for large hoists has migrated from the traditional DC technology to AC motors with cyclo convertor drives, and more recently, advances in pulse width modulation (PWM) drives have resulted in these being applied to large hoist drives. When combined with PWM drive technology, the induction motor presents the ideal solution for hoist applications This paper examines the factors in choosing a suitable PWM drive and motor for a hoist installation. Factors under consideration include: ? hoist duty cycle, ? drive rating restrictions, ? choice of power semiconductor device,, ? low speed operation, ? maintenance ? reliability The cage induction motor and synchronous motor are compared and it is shown that the induction motor is the motor of choice for large hoists.

May 1, 2010

By Dallas W. Davis

"Since May 1980, New Brunswick has called separate tenders for the right to explore and develop several potash prospects, as well as areas underlain by Alberta oil shale. These tender calls had in common the provision for a basic ad-valorem royalty, combined with sharing of cash flow after exceeding a 15-20% discontinued cash flow rate-of-return threshold. In the case of potash, the bidding variable was a share of cash flow, but for oil shale it was exploration expenditures committed, with the cash flow sharing to be negotiated at the time of application for a production lease. The Millstream potash occurrence, previously discovered by government drilling, received five bids (21.1% highest), the Dorchester ""grassroots area"" with four surmised drill targets apparently received no bids, and in the case of oil shale there were only two bids on the one block previously subjected to the most exploration.It is concluded that New Brunswick will not be successful in awarding the potash or oil shale rights in return for a comparable level of basic royalty and cash flow share as in the case of Millstream, unless it spends money in discovering prospects or sharing the exploration risk with companies. The approach is likely to work for oil shales only if current exploration proves the existence of much high-quality material or a definite trend of real increases in the price of oil is again established. Undoubtedly, it continues to be desirable to assure an on-going stable investment climate through award of potash and oil shale rights under terms which provide for a return that the public and future governments will consider fair. This could mean that some form or risk sharing with companies would be advisable."

Jan 1, 1983

By Theo Mayer

Presentation Outline Define data visualization in the context of workflow Present other industries? application and demonstrated benefits Provide conceptual tools to help you address a visualization strategy Hold 10,000 foot view ? to touch on many issues

May 1, 2008

By W. M. Lupton

"Internal grinding mill entries are routinely done by mill personnel during scheduled maintenance periods. Reasons for entry include mill liner life profiles, liner inspcections and replacement and grinding media investigations. These entries require employees to adhere to safety regulations and policies including special permitting, testing, procedure-following practices and the wearing of proper personal protective equipment.A realized semi-autogenous mill entry safety hazard is the unpredicted breakage and occasional shattering of large diameter grinding media while personnel are inside. This was a concern to both media user and supflier. American Barrick's Holt McDermott Mine has improved mi l operational procedures and the media manufacturer has assisted by their developments to essentially eliminate this problem.This paper presents the improvements instituted; and the author's wish to communicate this potential hazard to other large diameter SAG ball users or potential users.INTRODUCTIONAmerican Barrick' s Holt McDermott mine is situated on Highway 101, some 70 kilometers northeast of Kirkland Lake, Ontario, 120 km east of Timmins and 90 km northwest of Rouyn Noranda, Quebec. The mine draws 160 employees from these surrounding areas to extract and process the underground ore, and recover near 60,000 ounces of gold per year. The mill department is completing it's fifth year of operation this spring.The company and the employees are proud of the safety improvements realized over the short history of the mine. Post accident/incident reviews and pro-active safety awareness programs have substantially reduced the mine's accident frequency and severity to date.One of the mill department's objectives is to provide a safe working environment for mill personnel, which includes the interior of the grinding mills."

Jan 1, 1993

By G. S. Dobby, J. A. Finch

"A significant development in froth flotation technology has been the emerging industrial acceptance of column flotation during the past few years. Flotation columns are being employed now in several Canadian base metal concentrators and they are being considered f or a wide range of flotation applications throughout North and South America. Since the operating principles of a column differ markedly from those of conventional flotation machines, and have been poorly understood, scale-up of columns has been difficult. This paper describes a methodology f or translating laboratory column data to industrial operation.The scale-up model utilizes kin etic data that is obtained from a series of laboratory column experiments; the laboratory column can be as short as 2 m. For modelling purposes the column is considered to consist of two zones: the collection zone, where particle recovery occurs, and the cleaning zone, a packed bubble bed generated by downward flowing wash water. Mixing conditions in the collection zone have been characterized using the results of tracer experiments on plant columns at Mines Gaspe. The same experiments demonstrated the nearly complete suppression of entrained gangue minerals that is attained in the cleaning zone. The model explicitly accounts for both the collection zone and cleaning zone recoveries and allows for the effects of bubble overloading. Results of column scale-up experiments at Gibraltar Mines are presented."

Jan 1, 1986

By Dave N. K., T. P. Lim

"A fast, reliable and accurate method for radium-226 determination in environmental water samples has been devised, using an alpha spectroscopic technique. The correlation between barium-133 and radium-226 in the barium-radium sulphate precipitation mechanism was studied and in the limited experimental recovery range, the coefficient of correlation was r = 0.986. A self-absorption study for various barium carrier concentrations was also undertaken to obtain the least broadening of alpha energy line widths. An optimum value of 0.3 mg barium carrier was obtained for chemical recovery in the range of 85%.IntroductionWith the increase in uranium mining activities, the migration and spread of radioactivity via various environmental pathways is of great concern. Because of its inherent biological hazard and relatively long half-life, (approximately 1620 years), raidum-226 is frequently monitored as a measure of radioactive contamination of the environment. It is, therefore, necessary to modify existing methods for rapid determination of radium-226 in environmental samples for quick corrective measures in the event of seepage, dam leakage or discharge violations."

Jan 1, 1981