Search Documents

By K. Thuro, L. Wilfing, H. Kasling

"In mechanized tunneling, performance prediction is a crucial issue for estimating excavation costs and construction time of a tunnel project. The aim of this work is to compare the calculated parameters by penetration prediction models with the results of penetration tests during excavation by a Tunnel Boring Machine (TBM) at actual tunnel projects. This comparison helps to improve the existing prediction models (Gehring, 1995 and Rostami (Colorado School of Mines), 1997.) and to develop a new, so-called “Alpine Model” (research group ABROCK; Schneider et al., 2012).On-site penetration tests are a common tool to determine performance of a TBM in certain geological environments. During a test, the TBM is operated under defined conditions that allow comparing the results of different projects and machine types. There are two different types of penetration tests in use. The more common type, described by Bruland (1998a), is based on test drives at different thrust levels. The tests in this study are performed as start-stop-tests, meaning that the TBM starts from zero to the maximum possible thrust and reverse with slowly increasing respectively decreasing steps (Frenzel et al., 2012). To gain information about the interaction between TBM and rock mass, a detailed geological documentation including an analysis of the discontinuity pattern and laboratory testing for rock strength characterization are mandatory.Within the last year 16 penetration tests have been performed. The results are thrust- penetration curves (Figure 2) showing that up to a certain penetration rate only crushing occurs (subcritical penetration). From there the desired rock fragmentation process called chipping takes place (Frenzel et al., 2012). These two different fragmentation processes can be described best by a bilinear function as seen in Figure 3. Both, CSM- and Gehring-model, do not fit to the trend of the penetration rates determined during the excavation process as they are using potential or simple linear functions.Another parameter that has to be implemented into the new prediction model is the influence of discontinuities. In case of favorable orientation and spacing, discontinuities reduce the required thrust at same penetration rates. In contrast, unfavorable discontinuity systems can cause blocky faces and hence worse performance than predicted. Besides discontinuities, the toughness of rocks has to be taken into account when predicting the penetration as tough rocks need more energy to obtain complete failure than brittle rocks.Key advantage of these tests in comparison to existing are more data points in less time. By improving respectively extending the existing penetration prediction models with the stated parameters, the penetration prediction for TBMs can be more accurate and also wear calculation can benefit from this approach."

Jan 1, 2015

By Robert B. Parsons

"Two recent decisions by the Canadian courts could reduce the taxes paid by many profitable mines in Canada. At a time when the mining sector is hurting from an ever increasing tax burden and soft prices, the results of two cases are welcome news. Mining companies are well advised to check prior years' tax returns in the context of these developments. IntroductionSince 1976, the income tax legislation has provided a reduced rate of tax for taxpayers engaged in the mining of mineral resources, through the mechanism of the ""resource allowance"". The deduction given for the resource allowance effectively reduces the federal rate of tax by one quarter on resource profits. In general terms, ""resource profits"" are defined to include a taxpayer's income from: the production and processing in Canada of ore to any stage that is not beyond the prime metal stage (or the pellet stage or its equivalent in the case of iron ore); and, royalties computed with reference to the amount of value of production from mining operations in Canada.In computing income from these sources, the taxpayer must deduct expenses that may reasonably be regarded as applicable to those sources, with the exception of expenditures for Canadian exploration and development or financing costs.As a result of the mechanics of the calculation of the resource allowance, one quickly realizes that the lower the expenses deducted from the resource profits, the higher the resource profits and consequently the higher the 25% resource allowance. The impact of the recent court cases is to narrow the range of expenses which are required to be deducted in the determination of the resource profits.The two cases are outlined below."

Jan 1, 1991

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "Information-oriented construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of mountain tunnels (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electronic distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily control measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this suggested method. It then presents the typical results of a field verification test at a tunnel under construction and an example of evaluation of the ground conditions ahead of the face based on the 3D numerical analysis in three types of condition changes of ground deformation moduli.

Jan 1, 2015

"The North Star and Don Jon copper deposits lie beneath the waters of Thompson Lake, which is 12 miles east of Flin Flon, Manitoba. The deposits were discovered during the years 1949 and 1951 by diamond drilling done in the vicinity of pyritic showings on the shores of two small islands in the lake. The Don Jon ore body lies 1, 700 feet southeast of the North Star orebody and is connected with the North Star mine workings by a crosscut on the 600-foot level (Figure 1 ).Production began on January 1, 1955, at a combined rate of 200 tons per day. The ore is trucked, on 24 miles of highway, to the Hudson Bay Mining and Smelting Co., Limited mill at Flin Flon.Regional GeologyRocks in the Thompson Lake area are Precambrian volcanics, ranging in composition from andesite to rhyolite, with related tuffs and breccia. These rocks have a general north-south trend and are steeply dipping. The area is part of the Lac Aimee fault block, which probably is the southward extension of a south-plunging syncline now thrust some miles to the north. This regional deformation has produced many subsidiary zones of intense shearing and crumpling. It is in two of these zones of shearing and drag-folding that the orebodies occur. The only recognizable intrusive is a narrow diorite sill which trends northeasterly near the west shore of Thompson Lake.The North Star MineA pyritic showing, carrying some chalcopyrite, was discovered around the year 1930 on the west side of a small island near the west shore of Thompson Lake. This ground was included in a group of claims acquired by the Hudson Bay Exploration and Development Co., Limited in 1947.In the years 1949 to 1951, a diamond drilling program outlined a copper sulphide orebody. This ore zone comes to surface beneath the lake, about 300 feet north of the pyritic showing on the island."

Jan 1, 1949

The concept and practices of co-extraction of coal and methane have emerged in recent years to improve coal mining safety and productivity, utilise methane resources, and reduce fugitive emissions in environments that involve multiple coal seams with low gas permeability. The system of co-extraction integrates two previously separate operations of coal extraction and methane drainage. The coal mining operation reduces the coal seam gas pressure and creates strata fractures that enhance gas migration and capture from mine workings and surrounding coal seams. An effective methane drainage operation produces a consistent and quality clean energy product and, at the same time, reduces the methane concentration in underground workings and the methane content and pressure in the adjacent coal seams. This is a significant benefit in preventing gas explosions and outbursts, and promotes a safer and more productive coal mining environment. In addition, the co-extraction with enhanced utilisation of coal mine methane directly leads to a reduction in greenhouse gas emissions. Presented in this paper are key results and outcomes of a major Asia Pacific Partnership project carried out from 2008?2012 by the Commonwealth Scientific and Industrial Research Organisation in collaboration with Huainan Mining Industry (Group) Co. Ltd., to develop and demonstrate advanced technologies at Pansan mine, Huainan, that promote the concept and practices of co-extraction of coal and methane. A comprehensive approach was adopted to assess fundamental strata and coal seam methane conditions during mining, and optimise mining sequences and coal mine methane capture systems. The project has not only demonstrated a practical approach and procedures of advanced co-extraction of coal and methane systems but also delivered significant benefits and outcomes in improved mining safety and efficiency, increased methane capture and utilisation, and reduced fugitive methane emissions at the Pansan mine. The total mine gas drained increased from 25.36 Mm3 in 2007 to 47.0 Mm3 in 2011, and the mine gas utilisation increased from 4.94 Mm3 in 2007 to 21.15 Mm3 in 2011. The improved methane capture resulted in reduced coal and gas outburst risks and methane concentration levels at the mine workings, provided a safe working environment for coal production, boosted the mining efficiency, and eliminated methane related incidents over the last few years at Pansan mine.

Aug 1, 2013

By Shinji Muraishi, Shinji Kumai, Yasutaka Kedo, Takashi Kambe

"Magnetic pulse forming (MPF) is one of the extreme high-speed forming processes. A metal sheet which is accelerated by electromagnetic force is collided onto a mold and fine and sharp details of the product can be obtained. The deformation mechanism of the MPFed metal cannot be understood only by the microstructure observation of the deformed metal. The deformation behavior of the metal should be investigated also by considering the local microstructure change with strain, strain rate and temperature change during deformation. Numerical analysis is an effective method to achieve this requirement. In this study, pure Al and Cu sheets were deformed by MPF. Impact velocity of the metal sheet was calculated by using ANSYS Emag-Mechanical. Based on the obtained impact velocity, the deformation behavior of the metal sheet was reproduced, and local strain, strain rate, and temperature were analyzed by using ANSYS AUTODYN. The relationship between the local microstructure change of Al and Cu sheets and the deformation parameters was examined.INTRODUCTIONMagnetic pulse forming (MPF) is one of the high-speed forming processes using electromagnetic force. Fine and sharp details of the product can be obtained, and springback after deformation is extremely reduced in comparison to the conventional forming processes(Psyk, Risch, Kinsey, Tekkaya, & Kleiner, 2011). Figure 1 shows a schematic diagram of MPF. A metal sheet is placed over the coil in the discharge circuit. The discharge current runs through the coil, and magnetic fieldis producedaround the coil. An eddy current is inducedin the metal sheet. Interaction between magnetic field and eddy current creates electromagnetic force. The metal sheet accelerated by electromagnetic forcecollides ontothe mold. Forming is completed in a few tens of micro-seconds.MPF is suitable for metals with a high electrical conductivity like Al and Cu.The MPFed metal may have characteristic microstructure because of high strain rate deformation."

Jan 1, 2018

By Tong Qin, Jinxia Zhang, Fusheng Niu, Limei Bai

"The interaction between a deformable bubble and a rigid particle in viscous liquids under microgravity conditions is studied by direct numerical simulation via an Arbitrary-Lagrangian-Eulerian (ALE) method. Due to the microgravity, the bubble will stay as a sphere in the fluid without external forces and its deformation is caused by the moving particle. In this study we assume the flow field is axisymmetric and the motion of the gas inside the bubble is neglected. The particle equations and the Navier-Stokes equations for the fluid are solved in a unified finite element framework. The particle obtains an impact velocity by an external force and the impact velocity is varied over a wide range. A ‘critical time scale’ T0 was identified for the interaction process. For successful contacts between particle and bubble, the time scale of their relative motion must be less than T0.INTRODUCTIONThe particle-bubble interaction is an important process in many applied industrial domains such as water treatment, froth flotation and liquid steel purification. It is a complex three phase process in that it embraces many research areas: fluid hydrodynamics, interfacial forces, particle and bubble behaviour and solution chemistry.Derjaguin and Dukhin(1961) clarified the particle-bubble interaction by introducing three-zone model for small and medium size particles. When the particle is far away from the bubble surface, the hydrodynamic forces are dominant. The particle is driven toward the bubble surface by the particle inertial and gravity. This region is regarded as Zone 1 and the interaction in this zone is a collision subprocess. As the particle gets close to the bubble, it exits a zone where the liquid flow around the bubble surface creates a tangential stream from the upper surface of the bubble toward the rear of the bubble. This is Zone 2 which is called the diffusiophoretic zone. In Zone 3, the particle is very closed to the bubble, surface forces like van der Waals, electrostatic and structural forces are considered. Contrast to Zone 1, Zone3 can be regarded as an attachment subprocess."

Jan 1, 2016

By Marc Bétournay

This article examines how fuel cell technology and related power distribution system fits within mine operating requirements. Considerations for improvement of power plant architecture and functions to yield production advantages are presented. Improvements to conventional mining approaches are also discussed.

May 1, 2007

By D. S. Robertson, G. E. Nutter, T. P. Podolsky

"IntroductionBasal Proterozoic quartz-pebble conglomerates are found both west of Elliot Lake, in Duncan, Jarvis and Aweres Townships, north of Sault Ste. Marie and to the east and northeast of Sudbury, Ontario. Locally, while well packed and pyrite-rich, they carry little to no uranium. Locally, they carry gold. These features generally are ascribed to variations in the source areas of the rocks.In two other areas of Canada, similar basal Proterozoic units contain quartz-pebble conglomerate beds with uranium.Sakami LakeLocation and HistoryThe Sakarni Lake uranium deposit is found in a narrow, northeast-trending, Archean greenstone belt located 95 miles southeast of Fort George, on James Bay, and 240 miles north of Matagami, Quebec (Fig. 1).The deposit was detected by Inco in 1971, during an airborne EM survey which carried a newly developed Inco spectrometer system flown at 450 feet. Ground investigation, in 1972, resulted in the discovery and sampling of quartz-pebble conglomerate which yielded assays as high as 0.19% U3O8.Extensive field exploration was conducted between 1972 and 1975. Sixty-five diamond drill holes, to a total of 13,969 metres, served to define the extent and economic potential of the conglomerates which extend over a total strike length of about eight kilometres."

Jan 1, 1986

By D. F. Sangster, P. J. Hood, G. A. Gross

"Some results are presented of an integrated geological and geophysical study of Precambrian magnetite-quartz iron-formation in the Kapiko Iron Range north of Nakina, Ontario. Detailed geological and topographical mapping was carried out in conjunction with detailed geophysical investigations such as vertical magnetic field, vertical magnetic gradient, hammer seismic, horizontal-loop electromagnetic and magnetic susceptibility surveys. In addition, oriented drill cores were obtained for magnetic polarization studies.Vertical-force magnetic anomalies within individual rock units showed a strong positive correlation with topographic relief. Moreover, magnetic intensity was found not to be quantitatively proportional to the magnetite content in the rocks, due to the presence of high remanent magnetization of the magnetite. Also, the remanent polarization direction was sub parallel to the plunge of the fold structure and mineral lineation in associated rocks.Vertical magnetic gradient measurements were found to be more accurate in locating buried contacts between magnetite-quartz iron-formation and country rock than the vertical magnetic force data.An in-situ magnetic susceptibility meter was used to measure the magnetite content of iron-formation, and the measurements were subsequently compared with vertical-force magnetic results.The results of the EM survey were inconclusive; some magnetite-rich zones produced anomalies in the out-of-phase component. whereas others did not. The reasons for such inconsistencies are not yet apparent.Longitudinal seismic wave velocities measured parallel to the bedding in magnetite-quartz iron-formation ranged from 10,600 ft/sec. to 14,500 ft/sec. The seismic velocity appears to increase with an increase in deformation of the rocks."

Jan 1, 1966

By J. Groppo, W. Zhang, R. Honaker

"The flotation of monazite is depressed when using hydroxamic acid as a collector in the presence of calcium ions which may exist due to the dissolution of minerals such as calcite. Minor dosages of sodium hexametaphosphate (SHMP) were found to effectively depress calcite, whereas the flotation of monazite was not impaired in single mineral flotation tests. However, in a mixed mineral flotation system, monazite flotation was depressed significantly. The mechanism of hydroxamate adsorption on monazite and calcite, the depression mechanism of calcite on monazite, as well as the depression mechanism of SHMP on calcite and monazite were studied using micro-flotation, electro-kinetic, and adsorption tests. Findings indicate that the adsorption of hydroxamate on monazite was due to chemisorption while adsorption on calcite was a result of physical interaction. SHMP significantly increased the negative charges of calcite surfaces which depressed the adsorption of the hydroxamate anions on the calcite surfaces due to an elevated electrostatic repulsion force. When calcium-rich minerals such as calcite are mixed with monazite, the calcium ions dissolved from the mineral surfaces specifically adsorb onto the phosphate oxygen sites on the monazite mineral surfaces thereby causing depressing effects. The addition of SHMP to suppress collector adsorption on the calcite surfaces interacts with the calcium species that were specifically adsorbed onto the monazite surface, which prevents hydroxamic acid adsorption onto the rare earth oxygen sites due steric hindrance and results in the flotation depression of monazite. INTRODUCTIONAs one of the commercial rare earth ores, monazite has been widely exploited to produce additives for catalysts, batteries, alloys, etc. Because of the complexity and the fine nature of some monazite ores, methods such as gravity, magnetic, and electrostatic separation to treat beach sand monazite fail to produce satisfactory concentrates, suggesting the use of floatation is warranted (Cheng, Holtham, & Tran, 1993). The primary associated minerals of monazite ores include ilmenite, quartz, zircon, rutile, sillimanite (Dixit & Biswas, 1969; Pavez a& Peres, 1994, 1993). Using sodium oleate as collector for monazite has been reported in many studies (Cheng et al., 1993; Dixit & Biswas, 1969; Pavez & Peres, 1994, 1993). Several investigations have reported maximum floatability of monazite occurring at pH values between 8 and 9 (Cheng et al., 1993; Dixit & Biswas, 1969). A study conducted by Pavez and Peres (1994) compared the use of hydroxamate and sodium oleate for the treatment of a monazite ore and found that hydroxamate significantly improved the grade of rougher concentrate."

Jan 1, 2016

By Farzad Mohammadi, Patrick Littlejohn, David Sanguinetti

Arsenic levels in metal concentrates are increasing as mining companies turn to developing low grade and complex ores. When arsenic bearing minerals are smelted, arsenic deports as gases which must be neutralized by a scrubber system. The resulting scrubber effluent is high in dissolved arsenic and requires treatment before the wastewater can be discharged or re-used. Conventional arsenic removal relies on lime addition followed by calcium arsenate formation and precipitation as hydroxides. As an alternative, arsenic removal with sulphide precipitation is receiving more attention due to potential advantages of the technology. Process streams high in arsenic often contain concentrations of dissolved metals that may be selectively recovered during sulphidization, producing a product that can be reprocessed and reducing waste generation. This paper will review laboratory testing completed for arsenic removal through sulphide addition and precipitation of arsenic (III) sulphide in combination with metals recovery to offset arsenic removal costs.

Jan 1, 2014

By Michel Ruel, Ali Soltanzadeh

This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control and expert systems such as fuzzy logic controllers and neural networks. Three examples are presented: ARC (Advanced Regulatory Control) on pH in a comminution circuit, MPC (Model Predictive Control) for combustible management and FLC (Fuzzy Logic Control) on a Semi Autogenous Mill. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.

Jan 1, 2014

"Cobalt refining at Vale Canada (previously known as Inco) has been associated with Ni production. Because certain compounds of both metals carry risks for adverse health endpoints by inhalation exposure, it is critical to understand the aerosol concentrations of specific substances and the metallurgical processes through which they enter the air. Vale Canada has therefore decided to describe the histories of its Ni-related operations and to report industrial hygiene measurements when available. This paper describes electrolytic Co operations carried out at Port Colborne, Ontario (1954–1966), and provides aerosol measurements (1995–2008) for current Co electrowinning operations.RÉSUMÉ L’affinage du cobalt chez Vale Canada (anciennement Inco) a été associé à la production de nickel. Puisque certains composés de ces deux métaux comportent des risques d’effets néfastes pour la santé par exposition à l’inhalation, il est essentiel de comprendre les concentrations en aérosol des substances spécifiques ainsi que les procédés métallurgiques par lesquels ils entrent dans l’air. Vale Canada a donc décidé de décrire les historiques de ses opérations liées au nickel et de divulguer les mesures d’hygiène industrielle lorsqu’elles sont disponibles. Le présent article décrit les opérations électrolytiques effectuées sur le Co à Port Colborne, Ontario (1954–1966), et fournit des mesures de la teneur en aérosol (1995–2008) pour l’extraction électrolytique actuelle du Co."

Jan 1, 2015

By H. J. Rowley

THERE are many varieties of limestone, but for the general purposes of the pulp and paper industry, two classifications are sufficient: (1) High-calcium stone, which should be quite free from impurities and contain not less then 90 per cent calcium carbonate. (2) High-magnesium stone, containing not less than 25 per cent of magnesium carbonate. Before proceeding with detail on the use of limestone and lime in the industry, a few words regarding the pulp products made in Canada are desirable. By far the largest tonnage is made by grinding spruce and balsam logs on rotating sandstones or on artificial abrasive stones of the Norton or Carborundum types. This mechanical or groundwood pulp finds its largest use in the production of newsprint paper, of which it comprises about 80 per cent of the total fibrous substance employed-the remaining 20 per cent being unbleached sulphite pulp. No limestone or lime is directly employed in making groundwood pulp, as contrasted with the chemically prepared pulps, all of which require one or the other form of the base for their processing. Sulphite pulps comprise the next largest tonnage group. They are produced by boiling, under pressure and at elevated temperatures, spruce and balsam wood in chip form in solutions of bisulphites and sulphurous acid. The usual bisulphites employed are those of calcium and magnesium. Sodium, potassium, and ammonium bisulphites give progressively better pulps, but to date, in the absence of efficient recovery methods, cost has precluded their use.

Jan 1, 1939

By D. M. Watson

Mineral discoveries and subsequent extraction have led to the establishment of many small communities, some major towns and a few cities . In Canada, such developments have essentially occurred without benefit of long-range regional or local planning. In the past, this was not a cause for concern. Now, however, rising expectations and reorientation of social values have placed increasing responsibility on government and industry to ensure the long-term viability of communities and regions. Such responsibility means large investments by government in infrastructure and by industry in extractive and processing plants. Uncertainty in the interpretation of ore reserve estimates becomes a critical factor. The traditional methods of reporting reserves - "proven", "probable" , "possible" - may be useful in individual mine production planning, but they are inadequate for planning industrial and public infrastructure, The need for a better information base is critical, with clear and precise definitions of what is being reported, but we are a long way from achieving it. The challenge is therefore to develop a closer professional relationship between government and industry and to tie mineral development to long-range regional strategies.

Jan 1, 1977

"The Schist Lake mine, owned and operated by the Hudson Bay Mining and Smelting Co., Limited, is situated on the northwest arm of Schist Lake, 4 miles southeast of Flin Flon, Manitoba.The deposit was discovered early in 1947, during a diamond drilling program exploring small copper showings along the west shore of the lake. The orebodies came to surface between the mainland and the north end of Stitt Island.Production began in August, 1954, at an initial rate of 300 tons per day. Underground workings have been carried to the 1,700-foot level, where exploration work is now being done.General GeologyRocks of the area are Precambrian lava flows, with associated pyroclastic breccias and tuffs, and related minor intrusions. Their general strike is northwest and their dip is nearly vertical. Shearing is common and is related to the activity which caused intense folding and much faulting in the area. The larger faults and the fold axes trend a few degrees west of north. The lavas are mainly andesitic but a layer of sericite-carbonate schist, which is probably derived from a fine-grained, grey quartz porphyry, occupies most of Stitt Island and extends into the mine area. It is within this layer of schist that the ore deposit occurs (Figure 1).The OrebodiesThe ore occurs as tabular to lens-shaped bodies which strike northwest, dip nearly vertically, and plunge at 60 degrees to the southeast. The ore zone is 800 feet long and has been traced for a distance of 2,000 feet along the plunge (Figure 2). The maximum length of continuous ore within this zone is 200 feet. Widths of individual ore lenses vary from a maximum of 35 feet to a minimum of 2 feet.The ore consists of three distinct types: massive sphalerite-pyrite, massive chalcopyrite-sphalerite, and disseminated chalcopyrite-pyrite. The No. 1, or eastern, orebody is predominantly massive sphalerite-pyrite. The western part of the No. 2 orebody is massive chalcopyrite-sphalerite. The disseminated ore forms the eastern part and the lower end of the No. 2 orebody. All three types of ore, with patchy distribution, are found in the smaller lenses below the 1, 100-foot level.Metallic minerals, in order of deposition, are pyrite, arsenopyrite, chalcopyrite and sphalerite, galena, enargite, and gold. Both massive types of ore exhibit banding in many places, probably as a result of the selective replacement of schist. The disseminated ore was formed as a filling of the interstices in a brittle chert rock which appears to have been crushed by the same forces which produced the schist."

Jan 1, 1949

By K. Sugawaral, W. Tongampl, K. Hiruta, Takasaki Y., A. Hosoi, T. Katol, A. Shibayamal

Printed circuit boards of discarded personal computers, televisions, mobile phones and so on contain a significant amount of valuable metals. For the recycle of valuable metals contained in the printed circuit board wastes (P CB W), the effect of temperature on chlorination-volatilization of metals under chlorine gas flow was studied. The experimental sample used was powder of two types: crushed PCBW (Sample 1) made from PC and industrial machines, and crushed-combusted PCBW (Sample 2) made from Sample 1. The principal element in Sample 1 and Sample 2 was copper, about 13 wt% and 20 wt% respectively. Sample 1 was composed of pure metals such as copper, tin and lead. In comparison, Sample 2 consisted of oxide metals such as copper oxide, tin dioxide and silicon dioxide. The two samples were heated at predefined temperatures (ranging from 300 °C to 900 °C) in chlorine gas. The chlorine gas flow into the furnace was set at a rate of 100 mL/min. As a result, copper in Sample 1 began to volatilize at 600 °C and completely vaporized at 700 °C. While in Sample 2, copper started to volatilize at 600 °C and reached 100% vaporization at 800 °C. For Sample 1, zinc finished volatilizing at 500 °C, while for Sample 2, zinc volatilization reached only about 80% (maximum). Also, lead, nickel and titanium showed similar results. Consequently the volatilization rate of Sample 1 is higher than Sample 2 and the temperature dependency was verified for copper, lead, zinc, nickel, antimony, titanium and chromium. In fact, the volatilization rate of these metals increased with the temperature. This result reflects the difference between pure metal and metal oxide, as Sample 2 was combusted before the chlorination-volatilization test. Moreover, the chlorination reaction may be accelerated by a reductive atmosphere because Sample 1 contains carbon. In this study, the volatilization behavior of some valuable metals in PCBW by chlorine gas was observed. Further improvement in the rate of volatilization can be achieved by optimizing the experimental conditions.

Jan 1, 2011

By E. R. Landry

This paper reviews the current state of electric furnace technology, with emphasis on some of the more recent developments. A large section of the paper is devoted to the use of increasingly high power inputs by arc furnace operators. Operating practices are then covered, including some of the newer techniques which have been tried.

Jan 1, 1967

By Cheng-Ting Chiang

Information integration and exchange for the entire building life cycle is one of the most important issues in the AEC industry. Although the Building Information Model (BIM) technology is widely utilized to address them, BIM is mainly concerned within the design and construction (D&C) phases. In the operation and maintenance (O&M) phases, however, the information integration and exchange issue becomes more complicated because software applications here require not only BIM but other information outside of the AEC domain, e.g., disaster mitigation. Nowadays, most BIM-related research focuses on the D&C phases and pays less concern on the O&M phases, hence there is a research need that can help seamlessly transfer the information between the D&C and O&M phases. In this research, a software framework using ontology was designed to deal with aforementioned problems. The BIM data from the D&C phases were used as a foundation to generate new models for different software applications for the O&M phases. The ontology technique was employed to assist the model transformation process between the original BIM and the models for applications. Finally, a disaster mitigation example was chosen to validate the framework, in order to make sure that the transformation process is comprehensive and useful from domain experts? perspective.

Aug 1, 2013