Search Documents

By R. Brough

"Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind - and Secondary Hills. There are, however, only a few Primary Hills in operation with ""solid"" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a Cost per ton basis and/or downtime for liner replacement would be to a high.In other words, solid rubber has limits as any other material. However, 'SKEGA started to think, why not try to use the best properties of rubber as well as steel and combine the two materials together.Nearly 10 years ago SKECA started to test this concept in Rod Mills. A steel cap was vulcanized on to the leading face of the lifter bars, to be installed close to the feed end head (fig. 1)."

Jan 1, 1988

By Y. T. John Kwong

Abstract - To exploit an ore deposit without unduly impacting the environment is a challenge that can only be met by the concerted efforts of traditionally independent teams working on a mining project. Not only is detailed geology required of geologists to help mine engineers to develop a mine plan that assures generation of the least possible amount of mine waste, but metallurgists also have to select the most environmentally friendly mineral processing schemes, and communicate with environmental engineers with regard to complications that process chemicals may pose on proper mine waste management. Traditional ore deposit models typically emphasize the geological and mineralogical aspects of ore genesis to facilitate exploration for similar deposits. Recent research has shown that potential environmental liabilities such as acid mine drainage and metal leaching can readily be predicted according to deposit types. The choice of mining methods, mineral processing schemes, and decommissioning options are also largely dictated by the composition and setting of an orebody to be mined. Integrating such related information into traditional ore deposit descriptions would lead to the development of comprehensive environmental ore deposit models. The latter would facilitate communication among staff of the varied components of a mine project and aid with the selection of a combination of methods and strategies that would assure minimum environmental risks and impacts, reduce the overall project cost, and enhance sustainable development.

Jan 1, 2003

By H. Polkowska-Motrenko

Analytical methods for the determination of uranium and other precious elements in ores, industrial wastes and by-products have been developed. The analytical techniques employed are NAA and ICP-MS. Two procedures of digestion were applied: microwave acid digestion and alkali fusion. Accuracy was checked by using CRMs. Results of analysis of the same samples by the elaborated methods have been presented and compared. The methods will be used for estimating the capacity of uranium production for the Polish nuclear power programme.

Aug 1, 2010

By C. Sorel

The PAREX code has been developed since the nineties by CEA and AREVA to describe the PUREX process implemented in the French fuel reprocessing plants. It enables the calculation, either in steady or transitory states, of the behaviour of the different elements of interest at each process step. The high customized structure of the software allowed the implementation of various phenomenological models describing solvent extraction systems dedicated to uranium purification from crude ore to spent fuel. After qualification of the implemented models, the code was used to perform the design of flowsheets, for safety demonstration analysis or for operational assistance.

Aug 1, 2010

Everybody would agree that a good roadway leads to more efficient haulages by reducing haul times, smoother and safer operation for operator and less wear and tear on tires and equipment, thus improving availability and overall costs efficiency. There is a number of factors that come into play to achieve this especially when developing a mine. Excavations of Ramps and Headings: Operators should follow surveyors and layouts accurately while driving ramps. To maintain constant grades on ramps, which leads to better design control of water and easier grading of roadways. Dips and dives lead to needless over excavations and unnecessary cost and disposal of waste rock. When dressing a ramp some areas may require 2 to 3 feet of material to correct the dips and perfect to constant grade. You may ask yourself, is this all necessary? A small exercise is to follow a loaded haulage truck up ramp. At the first hump, grade change, notice the down shift and notice how far the truck travels to regain the up shift and his speed. The difference is remarkably noticeable when the grade is constant. All this leads to less driveline shock, less horsepower demand, better fuel efficiency and more productivity. Drill & Blast Patterns to control water for Ramp Headings: The drill pattern needs to allow for a ditch. A slight cross fall to form a ditch can easily be done with the lifters. The preferred side of the ditch is always the inside curve of the ramp as it has less tendency to erode roadbed material. On a level, the ditch is dictated by the sump location. A blasted ditch will eliminate water pounding and keep the roadbed dry. Water trapped in roadbed is the major cause of rollout and de-stability of roadbed. If the water is allowed to drain in the middle of the ramp it will cause erosion, movement and loss of fines and an increase in grading intervals.

Feb 1, 2008

By G. Portillo

Electrospark Deposition (ESD) is a pulsed-arc micro-welding process characterized by using high current electrical pulses, of a short duration, to deposit an electrode material on a metallic substrate. The short duration of the electrical pulse allows for a low heat input over the substrate and an extremely rapid solidification of the deposited material. As a result, the ESD is capable of a wide variety of microstructures like micro-segregationfree solid solutions, nanostructured grains, metastable structures, and amorphous phases. The present work shows a microstructural analysis of rapidly solidified Al-Ni alloys coatings by the ESD process. Field Emission Scanning Electron Microscopy (FE-SEM) and X-Ray Diffraction (XRD) were performed to present the microstructural evolution as a function of the welding parameters. The phases and non-equilibrium metastable structures present in the alloys, and their distribution, were found to be a sensitive function of the alloy composition; hence its formation is governed primarily by thermodynamic considerations.

Jan 1, 2011

By R. Farhat

Coating systems that yield a thermally grown oxide (TGO) protective layer have been proposed as a potential method for extending the lifecycle of components exposed to high temperature corrosion. This is particularly relevant to the petrochemical industry, where any reduction in corrosion rates can yield substantial cost reductions. The primary goal of this project is to develop a coating repair procedure and to investigate the oxidation performance of the repaired location. Electrospark deposition (ESD) was used to repair spalled segments of TGO grown on MCrA1Y substrates using various electrodes possessing mixed crystal structures. Specifically, electrodes of NiCoCrA1Y (BCC-FCC mixtures) and CoNiCrA1Y (FCCBCC mixtures), were deposited and oxidized to develop the TGO using a heat treatment of 24 hours at 1000°C in air. This presentation will focus on the microstructural evolution of the base metal and ESD repair on damaged area, in both as- deposited and oxidized forms. Results of SEM and XRD analysis will be presented.

Jan 1, 2011

By M. Xiao Bo

In recent years, there has been a heightened interest in the hydrometallurgical processing of sulfide ores and concentrates (especially copper sulfide ores and concentrates) mostly in the USA and Chile. Currently, hydrometallurgical operations account for about 30% of the primary copper production. In the present research, the leaching phenomena of IOCG (iron-oxide hosted copper-gold) ores and concentrates were studied. The IOCG ore, which is characterized as having a predominant amount of magnetite with fine chalcopyrite, is currently the center of attention for new copper resources. Heap leaching of IOCG ore is desirable because of its low cost. However, the leaching characteristics of the ores and concentrates and the mechanisms of copper leaching require investigation. This study defines the factors, which affect the leaching operation, such as the ORP, pH and oxidizing agents. Based on these results, the optimal leaching conditions are provided for pilot column leaching test and ultimately, commercial operations.

Jan 1, 2007

By Michael J. Beare

Requirements of both local permitting and international fundraising are forcing increasing numbers of projects in Russia and CIS to carry out dual technical studies. The principal focus of Russian mining project design is to satisfy local regulatory requirements. However, the technical documents are not generally accepted by international banks for project finance outside Russia. Similarly, international study documents are not accepted for permitting in Russia. The purpose of this paper is to compare and contrast Russian and international approaches to mine technical studies and draw conclusions from this. The Russian design and permitting system is centered around two key statutory technical documents termed the TEO Konditsy and the TEO Project. These documents are subject to regulatory approval and are broadly equivalent to the international prefeasibility study and the feasibility study respectively. A comparison of study criteria suggests similar approaches are used for the main technical disciplines in project design by the time projects are at the point of construction, but there is divergence on environmental matters where the OVOS (Russian ESIA equivalent) differs from an ESIA in some significant areas. The key differences relate to project footprint, level of technical detailed required for baseline studies, level of public consultation, consideration and disclosure of information, labour, coverage of community and social issues and the preparation of a Social and Environmental Management System (SEMS). It has been noted that the Russian Design Institutes often leave the detailed economic analysis until after the TEO Konditsy. A common problem is design teams tend to look for ?technological solutions? without due concern for project economics. The end result of this can be mines that are overcapitalized and hence sub-optimal. It can be concluded that Design Institutes have the monopoly on Russian permitting reports and this is likely to continue. Similarly, Russian institutes generally do not prepare feasibility studies to international standards and this is likely to continue to be the case. Therefore to achieve the requirement of dual technical studies, the international consultants and Russian Design Institutes will need to cooperate on a joint work program. Key issues will be to ensure the most appropriate option studies are carried out at the right stages, that project economics are considered throughout the study, and that the environmental work program covers the additional studies necessary for the ESIA.

May 1, 2009

By Y. -B. Kang

New databases are being developed to provide the capability to evaluate the suitability of present and potential new Mg alloys for automotive applications through cost-effective calculations. An extensive and complete thermodynamic database is being prepared for Mg alloys formed from among 25 present and potential alloying elements. The database is being developed by critical evaluation, modeling and optimization of available phase equilibrium and thermodynamic data. It contains model parameters giving the thermodynamic properties as functions of temperature and composition. Using the FactSage thermodynamic software, users can access the database to calculate the amounts and compositions of all phases at equilibrium at any temperature and composition or to calculate any phase diagram section in multicomponent alloys, to follow the course of equilibrium or non-equilibrium cooling, to calculate corresponding heat effects, etc. A database of densities and lattice parameters of Mg alloys and intermetallics (as functions of temperature and composition) is also being developed in order to permit the calculation of volume changes during cooling and phase transformations, c/a ratios of the hcp phase, etc.

Jan 1, 2006

By Z. D. Hora

Brick shales and refractory clays are mined at Sumas Mountain near Abbotsford. Sholes and stoneware clays elsewhere in the province have not been developed. THE SUMAS MOUNTAIN deposit near Abbotsford, 80 km east of Vancouver, has been in continuous production since 1905. The deposit is exposed in a small outlier and comprises a sequence of alternating beds of clay and sand. Beds are of Eocene age. Within the 400 m thick ness of sediments are seven distinctive conglomerate members, some up to 20 m thick, interbedded with fine grained sediments including claystones and siltstone , or "shales". Shale is quarried to produce a variety of bricks, sewer pipes and similar products; it is also used for cement. Several different shale beds have been mined over the years and exhibit a variety of fired colours ranging from buff-pink grey to deep red; pyrometric cone equivalents (PCE) range from 3 to 20. A layer of fireclay 3 to 4 m thick that occurs at the base of the sequence has pinkish white to light buff fired colour and PCE of 30 to 33. It is used as a 266 primary component to produce refractory bricks. The shale is quarried and processed by Clayburn Industries Limited of Abbotsford. Another similar but smaller outlier of the same geological formation is known from Blue Mountain, about 20 km northwest of Mission. Other ceramic clays in British Columbia are reported from Quesnel (7 m bed of white stoneware clay, PCE 17 to 19), Giscome Rapids (25 km north of Prince George, 10 m bed of stoneware clay to PCE 31) and anaimo-Comox area (buff to red firing "shales", PCE 8 to 10-1 12) . From 1959 to 1974 Cretaceous shale from Saturna Island in the Strait of Georgia was used to produce lightweight aggregate. Similar deposits of expanding shale are known from the vicinity of Duncan on Vancouver Island.

Jan 1, 1984

By Marcel Vallée

"Abstract-In recent years, several unsavory events in international mineral exploration, as well as several widely publicized project difficulties and failures have occurred. The report Setting New Standards has "raised the bar" and proclaimed a "commitment to continuous improvement... and change." We need to evolve from our "generally accepted" practices to more effective quality assurance policies, guidelines and standards. Several steps will be required to support the work of the "qualified persons" now wholly entrusted with technical and professional matters:• adopt a mineral development model and objectives appropriate to orient the selection of workmethods and verification procedures suitable to increase the profitability of these activities;• review the definitions and implications of the terms practice, guideline and standard;• review three quality assurance systems with emphasis on commitment of company management and complementary emphasis on systematic quality policies, plans and manuals (ISO 9000), continuous improvement through "profound knowledge" (Deming, 1986), and self-appraisal of continuous improvement and client satisfaction using the Qualimeter Guide (Québec Society for Quality);• determine, from the objectives of the mineral development model proposed and the problems often encountered, the requirements of resource/reserve estimation and the production feasibility study. To regain investors’ confidence and improve the returns from mineral development activities, an explicit commitment to quality by the board of directors and the management of every company is required.A number of mining companies have gained ISO 9002 certification for their operations but exploration companies should start by developing and implementing quality assurance guidelines and standards based on the ISO 9001 pattern, without achieving actual ISO certification in the short term. Both professional associations and industry organizations must be involved in the process of developing the required quality and continuous improvement guidelines and standards."

Jan 1, 1998

By Jennifer Young

Presentation Outline ? Introduction ? Aboriginal Inclusiveness ? Common interpretations, practices ? Aboriginal Community Expectations ? Lessons Learned ? Native Code of Conduct Introduction Jennifer Young ? Nestu'et (Mi'kmaq) means: becoming wiser, becoming more knowledgeable Aboriginal Inclusiveness ? Internal hiring strategies (affirmative action) ? Incorporating cultural awareness programs ? Approaches in governmental/organizational policy development Practices in negotiating economic development and fiscal sharing strategies

May 1, 2010

By Philip Peck

Mine closure issues ?Narrow issues: ?Environmental focus; ?Broad issues: ?Social issues and sustainability; ?Continued importance of mining; ?Historical legacies from closed mines; ?Barriers to development; ?Migration [ir]reversibility Dealing with closure issues ?A matter of choice ?Option 1: Engagein solving closure problems as best possible; ?Option 2: Exit, leaving the playing field to firms not interested in solving problems ?Option 3: Delay, till better time to enter or until early entry [by others] fails and pick property up cheap [?].

May 1, 2006

By J. Moyes

The Intec Copper Process is an internationally patented hydrometallurgical process for the extraction of pure copper and precious metals from sulfide concentrates. Developed and proven in Sydney, Australia at a cost of US$15m over the last ten years, the Intec Copper Process is now ready for commercial application. The Intec Copper Process has several notable advantages over both smelting and other hydrometallurgical processes. Starting from a base of substantially lower capital and operating costs than any other conventional or developing process, the Intec Copper Process is economically viable at capacity levels as low as 15,000tpa-Cu, and capable of accepting low grade and metallurgically complex concentrates. Precious metals are recovered within the Intec Copper Process circuit, without the need to re-treatment of the environmentally stable solid residues. The Intec Copper Process offers the lowest energy consumption of the available technologies, with no liquid emissions or production of noxious gases. Unlike smelting, sulfur is recovered in the solid residues in elemental form.

May 1, 2002

By E. Marcotte

"Technology developments and improvements are imperative to maintain a viable mineral processing industry. In order to achieve optimum implementation of technology in processing plants, safety conscious and efficient work forces are required. Effective management methods are required to prevent employee injuries, equipment or environmental damage and process losses. Good leadership also provides for employees to perform their work in the safest and most efficient manners to attain optimum recoveries of the valuable minerals and produce high quality mill products. Equipment and processes must be designed, operated and maintained as required to assure safe and efficient mineral processing.INTRODUCTIONThe Canadian mining industry must contend with many challenges to attain and maintain a competitive position in today's global market. Canadian Mineral Processors play a vital role in meeting the challenges and achieving optimum mineral productivity.Ongoing technology developments and improvements continue to be imperative to maintain a viable mineral processing industry. The efficient implementation of technology developments requires a safety conscious, skillful and productive work force.In addition to technical and human resources, challenges may also include governments, labour unions or environmental advocates who at times may appear to be misguided or unrealistic. Canadian Mineral Processors must not allow themselves to be overwhelmed by these apparent obstacles but must use their demonstrated ingenuity to achieve successful solutions.It should be recognized that the majority of the Canadian work force are, in fact, a potentially talented and skillful people with ambitions to excel. As leaders of people, we must provide the methodology, incentive and direction that will allow our work forces to realize their ambitions. If the potentials of our work forces are not recognized and leadership is not properly exercised much loss will occur. That is, safe effective and efficient work will not be achieved."

Jan 1, 1993

By Blair Hrabi

Introduction; ?Risks Associated with the Resource Estimation Process; ?Limitations of Available Data; ?Geological and Structural Control of Mineralization Trends; ?Recognizing Multiple Mineralization Controls and Complex Trends; ?Accurate Geodomaining; ?Conclusions.

May 1, 2013

World copper electrowinning tankhouse plant practices have been surveyed. This survey is a supplement to previous surveys that have been carried out in 1995, 1999, 2001, 2002 and 2003. On a world basis, process technology trends include the further installation of automated electrode handling systems including permanent cathode systems, automated cathode handling machines, fully automatic cranes and polymer concrete cells. Designs also have included larger electrode sizes and higher electrolyte flows and current densities. Overall these trends have further resulted in optimized tank house productivities and improved electrowon cathode purity. Most greenfield copper electrowinning projects are occurring in South America and Central Africa.

Jan 1, 2007

By S. D. Logan

This presentation describes a lightweight automobile body structure concept developed at DaimlerChrysler to support a high fuel-efficiency vehicle project. This body structure consisted primarily of large thin-wall magnesium castings and resulted in a more than 40% weight reduction with a minimal cost increase over a conventional steel structure while achieving significantly improved structural performance as evaluated through CAE simulations. One concept vehicle was built for the purpose of demonstrating concept feasibility. Several slides showing the prototype build process are presented. The presentation also describes several large thin-wall die casting body applications that are in current production or have been used in recent production automotive applications and identifies areas where further development could improve the chances of a magnesium intensive body structure becoming a production reality at a later time.

Jan 1, 2006

By A. Jain

During sheet forming, metal experiences not only multi-axial load, it also undergoes strain path changes. For example, metal in the flange region may be drawn, may bend and unbend through a bead, before bending around a die radius, etc. Compression data were obtained from AZ31 sheet after pre-straining in compression along an orthogonal direction. The compression directions correspond to the sheet product (rolling-RD, transverse-TD, and normal-ND) directions. Three cases are examined: slip dominated deformation (ND) followed by twin dominated (RD or TD) deformation, twin dominated (RD or TD) followed by de-twinning (ND), and twin dominated (e.g. RD) followed by cross-twinning or secondary twinning (e.g. TD). Slip induced pre-straining simply hardens the material, while twin dominated pre-straining alters the texture allowing the material to either de-twin or re-twin upon changing the strain path. Polycrystal plasticity modeling has been used to predict qualitative features of the flow curves during strain path changes.

Jan 1, 2006