Search Documents

By Worthen Bradley

This paper describing the metallurgical practice and costs at the reduction plant of the. Sulphur Bank Syndicate, Clearlake, Calif., is one of a series of papers on the treatment of ores being prepared by the Bureau f Mines. The reduction plant and mine of the Sulphur Bank Syndicate are on the eastern shore of Clear Lake, in Lake County, Calif., 4 miles from the town of Clearlake and 125 miles north of San Francisco.

Jan 1, 1931

By Harold E. Heide

Although the United States has been the largest consumer of tin, only a small quantity of tin was produced or. the North American Continent during peace times, and thy deficiency was made UP by foreign imports. Because the most important sources of tin wore cut off by the war with Japan, it became necessary to increase imports from South America and Africa and, if possible, develop domestic tin reserves. Most of the tin produced in North America has come from the Seward Peninsula, Alaska, and a substantial portion of this was produced from the Potato Mountain area. Tin was first identified as occurring in the Seward Peninsula by A. H. Brooks in 1900, when a part of heavy concentrates from Anikovik River and Buhna Creek, one of its tributaries, proved to be stream tin. 4/ His report was given considerable publicity by the daily press, and the first steamers north in 1901 carried a number of prospectors bound for the Seward Peninsula to search for tin. The deposits of stream tin on Buck Creek in the Potato Mountain area were discovered in the fall of 1901. 2/

Jan 1, 1949

By J. E. Zeilinger, John Nagy, Irving Hartman

"INTRODUCTION Experience and research have shown that an effective way to reduce structural damage from explosions is to provide adequate pressure-relief vents in the walls of equipment and buildings within which explosions might occur. In general, free or unrestricted openings represent the most efficient type of vent. However, in many manufacturing operations it is impractical to use free vents, and it becomes necessary to cover the openings with diaphragms or blow-out disks, hinged panels, or other devices, in order to give protection against weather changes, to prevent the efflux of dusts or vapors from equipment during normal operations, or for other reasons.A few data on the pressure-relieving capacities of hinged panels and a paper diaphragm were published in Bureau of Mines Report of Investigations 3924,4/ which covered the first phase of the dust-explosion venting study made by the Bureau. The present report describes recent experiments that were made to determine the relative effectiveness of an unrestricted vent and 22 types of closures, including various paper, cloth, and metal-foil diaphragms, hinged doors or panels, and several kinds of scored and unscored glass panes.The tests showed that many of the vent closures were effective in releasing the explosions rapidly during their incipient stage, so that the development of destructive pressures was prevented. Vents of this type should prove useful in safeguarding industrial equipment from severe explosion damage. The experiments disclosed that the venting capacities of the diaphragms are approximately inversely proportional to their static bursting strengths."

Jan 1, 1950

By H. W. GILLETr, E. L. Mack

The production of small heats of alloy steels on an experimental scale is often desirable in beginning the study of new alloy steels before large amounts of expensive alloys are used in heats of commercial size. Such small heats can sometimes be made up at crucible-steel plants, but few crucible-steel makers care to undertake experimental heats for other firms. Small electric furnaces offer some advantages over crucible furnaces for experimental work. Hansen1 in 1909 described a small 100-kilowatt single-phase, direct- arc furnace with a capacity of 50 to 300 pounds of steel, and such furnaces, of 200 pounds capacity or larger, are being successfully used by various firms for experimental work. They have the advan- tage of using the same metallurgical procedure as is used in prac- tice for larger electric furnaces. The very small sizes have the draw- back of lack of precision in controlling the carbon content of the steel. Small Rennerfelt two-phase, indirect-arc furnaces of 40 to 60 kilo- watts and small Industrial Electric Furnace Co. furnaces, single- phase with one electrode embedded in the hearth, of 25 to 50 kilo- watts, are also in use by a few firms for experimental work or for production on a very small scale. Hoskins carbon-plate resistor crucible furnaces are also sometimes used. Little seems to have been published on the use of these furnaces in making experimental alloy steels. Keeney' has given data on the making of uranium steels in a tilting Siemens furnace of 25 pounds capacity, and has described a small stationary Siemens furnace.

Jan 1, 1922

By R. V. Higgins

In a recent report3/ the authors presented a rapid method of calculating, by means of a desk calculator, the future performance of oil reservoirs in which the motivating agent was gas. The accuracy of the method was tested by data obtained from an electronic computer. Because of the accuracy obtained for the limited number of calculations performed, considerable interest has been expressed in the electronic computer program used to obtain the comparative data by an analytical solution. Accordingly, the computer procedures for the analytical solution are presented in this report. In an earlier report, 4/ a reservoir appraisal procedure was published in which an iterative method was used. Many requests were received for the computer program used to obtain the values given in that paper. That program, with some modifications, also is presented in this report. The modifications are given because of the progress that his been made in computers, and because much of the program for the analytical solution is usable for the iterative procedure.

Jan 1, 1960

By Frank A. Peters

With the current renewed interest in advancing the technology for producing alumina from domestic raw materials, revisions of previous cost estimates to provide planning data are urgently needed. Completely new cost estimates on a 1973 basis are included for four alumina-from-clay processes and one alumina-from-anorthosite process. These estimates are based on new or previously calculated material balances, recalculated heat requirements, and new equipment designs. The use of larger and more modern equipment has permitted a significant reduction in labor requirements as well as equipment costs. Chemical prices, labor rates, and utility rates typical of late 1973 are used in these cost estimates. In addition to the revised cost estimates, all 21 previously published alumina evaluations compiled by the Bureau of Mines were updated to show the effect of inflation using an inflation index and late 1973 chemical prices, labor rates, and utility rates.

Jan 1, 1974

By L. A. Grant

This paper describing the concentrator practice of the Montana Mines Corporation at Helena. Mont., is one of a series of articles on milling methods and costs being prepared by the United States Bureau of Mines. The Spring Hill mine and mill are located 4 miles south and west of Helena, Mont., near the head of Grizzly Gulch. The mine portal is on the east slope of the gulch, and the mill is directly opposite on the west slope. Grizzly Gulch is one of the tyro gulches which unite at the south end of Helena to form Last Chance Gulch, on which the main street of Helena is built.

Jan 1, 1931

By R. L. Solmer

During 1959-61, the Bureau of Mines investigated the strain and deformation induced in rock and concrete linings around mine openings by retreat panel caving at the Climax Molybdenum mine. Two concrete-lined slusher drifts on the Phillipson level of the mine were instrumented with both electrical strain gages and extensometers. Changes in strain and deformation were recorded over an 18-month period during the undercutting and caving of the mining panel. General agreement was found between the strain and deformation measurements and the hypothesis that the vertical component of the stress field on the openings is almost completely removed by undercutting. This phenomenon is a possible explanation for the structural failures that occur in the slusher drifts during the undercutting cycle.

Jan 1, 1965

By Elaine Cullen, Launa Mallett, Mike Jenkins, C. M. K. Boldt, Thomas Camm

The material in this Information Circular was presented at the National Institute for Occupational Safety and Health’s (NIOSH) open-industry briefing held during the 2004 Northwest Mining Association conference in Spokane, WA. The open-industry briefing discussed results of recently completed and on-going mine safety- and health-related research conducted at NIOSH’s Spokane and Pittsburgh Research Laboratories on the human side of mining—the miner. The first paper sets the stage for what mining has achieved and what we mean by “getting to zero.” The second paper, “Help Experienced Miners Become Great On-the-Job Trainers,” distinguishes between experienced miners and trainers. This paper provides some key concepts for turning great miners into great trainers. “The Power of Story-Telling in Getting Through to Miners” explains the history and importance of stories in the culture and training of miners. Finally, “Understanding Self in Stressful Working Environments,” describes the personal and social aspects of the working environment, much of which parallels familial theories. The downward trend of deaths in U.S. mining has been remarkable. The number of miners killed or injured each year has decreased steadily over the past 100 years. Some charts show these trends overlain with important events such as World War II and the Mine Safety and Health Act. However, this downward trend in mining fatalities has flattened out. How can you get to zero accidents? Do you concentrate on technological advances and equipment maintenance to avoid malfunctions? Do you concentrate on developing work processes and organizational structures that minimize risk? Do you combine them and take a systems approach that links one to the other with an evaluative loop? Safety efforts in mining have used all of these approaches. What more can we do to get to zero? Getting to zero will require two objectives: A clear and unshakeable belief that it can be done and attention to the human side of mining. Getting to zero is not a new idea; it has been used by mine companies and safety professionals for years as the safety goal. But getting to zero is not so much a physical goal as it is a belief that there are no insurmountable barriers to achieving the goal.

Jan 3, 2006

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease 'of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

By Warren D. Longwill

All known resources within the four proposed RARE II additions to the Yolla Bolly-Middle Eel Wilderness in northwestern California occur in the Gig Butte-Shinbone study area (fig. 1). No mineral resources are Figure 1.--NEAR HERE. known in the East Fork, Murphy blade, or Wilderness Contiguous units. About 2,400 tons (2,177 t) of subeconomic manganese resources averaging 9.5 percent manganese have been estimated at the Blue Jay Mine in the Big Butte-Shinbone unit. In addition about 9,700 tons (8,793 t) of subeconomic chromium-nickel-cobalt resources in thin laterite soil at the Grubstake Prospect contain about 1.27 percent chromium oxide, 0.45 percent nickel, and 0.03 percent cobalt. Adjacent Ultramafic rock outcrops have pods averaging 2.5 percent chromium oxide (Cr203); one pod contains about 40 tons (36 t) of indicated subeconomic resources.

Jan 1, 1981

By C. H. Elder

An analysis of the geologic structure of an area of Buchanan County, Va., was made by the Bureau of Mines using imagery from an airborne AN/APQ-97 side-looking radar system to evaluate that mapping technique for delineating structural features that may cause mining problems. Side-looking airborne radar (SLAR) was found to be a useful remote sensing tool for geologic structural analysis, Fault and joint systems identified by lineaments and linear patterns in the imagery were verified by surface and in-mine observations. Little Paw Paw fault was extended 10 miles by SLAR lineament analysis. A 22-mile fault, here named the Bishop-Bradshaw Creek fault, was mapped by lineament analysis and verified by observation of the fault on the Bishop Coal Co. mine map and on offset patterns of commercial gas production along the fault and surface observation of lineament along the fault. Three major super-imposed joint sets and several fault or fractured zones were identified by SLAR lineament analysis, showing more complex structure than earlier mapping indicated. SLAR imagery accurately delineated structural features that are known to affect gas migration and accumulation and that weaken the rock forming the immediate roof to mine workings, causing mining problems and potentially hazardous environment in the mines.

Jan 1, 1974

By Martin Hertzberg

The concept of limit burning velocities is used to formulate a quantitative theory of flammability limits. Competing processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. There are four competing processes and one complication: (a) Free, buoyant convection, (b) conductive-convective wall losses, (c) radiation, (d) selective, diffusional demixing (the complication), and (e) flow gradient effects (flame stretch). These complexities are unraveled by creating an idealization that is initially freed from these competing processes. The ideal serves as a standard, and its burning velocity (Su), ideal is a unique function of the initial thermodynamic variables of state. By adding each process individually, it is possible to evaluate their significance, quantitatively, in terms of a limit velocity (Su)a , b , c , or e , and to explore the nature of their cooperative interactions. The larger the limit velocity, the more significant the process. The apparently diverse observations of flammability behavior are readily unified within this simple, conceptual framework.

Jan 1, 1976

By William M. McKewan

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Ropes of sizes ranging from 3/4 to 2 in. in diameter and from 2 to 35 ft in length were tested to determine their breaking strength, elongation, and torque. This was done to characterize the test equipment on ropes used in mine hoisting systems.

Jan 1, 1990

By P. M. Sullivan

At its College Park Metallurgy Research Center in Maryland, the Bureau of Mines has installed and is operating a 5-ton-per-hour pilot plant for continuous mechanical separation of values contained in raw urban refuse. The entire sys tern was assembled using commercially available equipment. The process relies on multistage processing including shredding, air classification, screening, gravity concentration, and electrostatic separation. Compactor trucks deliver raw refuse collected along typical routes in metropolitan Washington, D.C., to the pilot plant. The loads are separated into concentrates of (1) light-gage iron, (2) massive metals, (3) glass, (4) putrescibles and waste combustibles, (5) paper, and (6) plastics. While some refinements remain to be made in the processing system flow-sheet, the data obtained to date have been highly encouraging, indicating favorable economics for commercial-size plants.

Jan 1, 1973

By R. L. Benner

A compound stability diagram was constructed by the Bureau of Mines for the Zn-Fe-S-O system to show the phases that should be thermodynamically stable at various temperatures, oxygen pressures, and SO2 pressures. The diagram was demonstrated to have good qualitative value for predicting stable phases that may, in turn, be related to the recovery of zinc in the leaching phase of the electrolytic zinc process. The study showed that roasting temperature is the most Significant variable in preventing roaster formation of zinc ferrite, which is directly related to subsequent extraction of zinc in the leaching step.

Jan 1, 1966

By Walter W. Hyde

This paper describing the mining and preparation of sand and gravel for a number of special markets by the East Texas Gravel Co., Dallas, Tex., is one of a series being prepared on the subject by the United States Bureau of Mines. These articles are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole, but on the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1931

By J. F. Barkley

The work covered in this report was done to meet the requests from many Government agencies for information on alleviating sludge difficulties in No. 6 (Bunker C) fuel-oil storage tanks. Accumulated sludge at times caused serious loss in tank capacities; pumps became overloaded or lost suction; strainers often required very frequent cleaning; fuel-oil heaters in some instances became fouled and inefficient; and gobs of sludge that passed the strainers interfered with good combustion. The requests also included questions regarding the usefulness in general of oil "additives" for preventing sludge and the relative merits of the many trade-named additives being marketed. Realizing that preventing such difficulties would result in substantial savings to the Government, an investigation was begun with the limited funds avail-able. Although various claims are made for No. 6 fuel-oil additives other than preventing sludge, only an investigation as regards the storage tank-sludge problem has been possible.

Jan 1, 1955

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969