Search Documents

By B. J. Dalton

The Helium Research Center, Helium Activity, Bureau of Mines, is presently engaged in a critical examination of all of the PVT data on helium that appear in the literature. The long-range objective is the development of a single equation of state for helium that will allow all of the thermodynamic properties to be calculated and will reproduce all of the data within the accuracy with which the data are known. A preliminary objective is to obtain the best values of the second virial coefficients and to develop an equation that will reproduce the best values as a function of temperature. The method of treatment consists in expressing the PV product of a gas, for a given isotherm, in terms of a power series in either the pressure or the density and evaluating the constants by least squares solution. Associated with these functions whose coefficients have been evaluated by least squares, the following errors, or deviations, are of interest; the standard error of a single measurement; the standard error in each coefficient; and the standard error of the resulting function.

Jan 1, 1964

By Thomas V. Falkie, R. Venkataramani

Table

Jan 1, 1972

By W. R. Reed

Drilling with water has the potential to significantly reduce the respirable dust concentrations generated from small-diameter rotary drills when drilling blastholes on surface mining operations. However, water adverseky affects tri- cone drill bits commonly used in surface drilling operations, causing excessive wear and premature replacement. Consequently, dry drilling with a dust collector system has the most widespread use in the industry. Tests have been conducted by the National Institute of Occupational Safety and Health (NOSH), Pittsburgh Research Laboratory (PRL) on a newly designed device for smaller diameter drills that separates the water from the bailing air before it reaches the bit and thus provides the cost benefit of dry drilling while providing the benefit of wet drilling for dust suppression. The water that is delivered to the hole with the bailing air is separated from the air by a proprietary mechanical device that is encased in a drill sub (short section of drill rod/pipe) located immediately behind the cutting bit. A cascade cyclone and a real-time dust monitor were used to sample dust emissions from the holes. Dust concentrations and silica content were measured when drilling dry versus drilling wet. The tests show that drilling with this water separating sub can reduce both measured dust emissions from the boreholes and visible dust around the drill rig.

By Manuel Gomez

A general prediction model for the Hardgrove grindability index was constructed from 735 coal samples using the proximate analysis, heating value, and sulfur content. The coals used to develop the general model ranged in volatile matter from 12.8 to 49.2 percent, dry basis, and had grindability indexes ranging from 35 to 121. A restricted model applicable to bituminous coals having grindabilities in the 40 to 110 range was developed from the proximate analysis and the petrographic composition of the coal. The prediction of coal grindability within a single seam was also investigated. The results reported support the belief that mechanical properties of the coal are related to both chemical and petrographic factors of the coal. The mechanical properties of coal may be forecast in advance of mining because the variables used as input to the prediction models can be measured from drill core samples collected during exploration.

Jan 1, 1970

By G. S. Price

This paper, which describes the milling practice at the Page concentrator of the Federal Mining and Smelting Co., is one of a series being prepared by the Bureau of Mines. The Page mine and mill are located on Silver Creek, 3 miles west of Kellogg, Idaho, and 1 mile south of United States Highway No. 10. Supplies and concentrates are hauled by truck over an automobile road which connects Highway No. 10 with the property. The concentrator has capacity to treat 300 tons of ore per day and utilizes all-flotation methods of treatment. Power is supplied from the main line of the Washington Water Power Co. which runs from Spokane, Wash., to Kellogg, Idaho. Water is obtained from the mine and also from a well which is situated 1 mile distant from the concentrator and about 600 feet in elevation below the concentrator.

Jan 1, 1932

By J. B. Stephenson

The Bureau of Mines, under an interagency agreement with the Department of Energy (DOE), investigated the feasibility of hardfacing the critical surfaces of valves and similar devices by chemical vapor deposition. The purpose of this research was to increase the wear resistance of these components for use in the abrasive and erosive environment of coal gasification units. Tungsten and molybdenum coatings were produced on nickel-plated carbon steels and stain-less steels by hydrogen reduction of the metal hexafluoride at 325° to 600° C. Titanium nitride coatings were produced on low-carbon steels by the reaction of titanium tetrachloride, hydrogen, and nitrogen at 1,000° C. Titanium carbonitride coatings were produced on low-carbon steels by the reaction of nitrogen, hydrogen, and methane at 900° C. Tungsten, molybdenum and titanium nitride coatings were formed on 6-, 10-, and l2-inch (0.15-, 0.25-, and 0.30-meter) ball valve seats for evaluation in the low-Btu coal gasification pilot plant at the Morgantown Energy Research Center, Morgantown, W. Va.

Jan 1, 1979

By J. W. Paul, A. C. Fieldner

"In cooperation with the New York and New Jersey State Bridge and Tunnel Commissions, the Bureau of Mines has just completed the construction of an experimental tunnel in the Bureau's experimental mine at Bruceton, Pa., near Pittsburgh, Pa. The purpose of this tunnel is to make a final study of the ventilation problems arising in the adequate ventilation of vehicular tunnels for automobiles and trucks, especially the 9000-foot tubes that are being designed. to handle the traffic between New York City and New Jersey under the Hudson River.Chief engineer, Clifford M. Holland, of the Tunnel Commissions has shown that there are three principal problems involved in planning the ventilation of this tunnel, namely - (1) The amount and composition of exhaust gases from motor vehicles; (2) The dilution necessary to render these exhaust gases harmless; (3) Determination of coefficients of airflow and horse-power required in ducts, bends and openings.Composition of automobile exhaust gases.The answer to the first problem was obtained by making road tests on 101 automobiles and trucks at the Pittsburgh experiment station. These machines were taken from service without any previous adjustment so that the composition and amount of the exhaust gas may be taken as representative of actual operating conditions prevailing in the tunnel. A report covering the results of these tests was submitted to the chief engineer of the Tunnel Commissions, on November 1, 1920, and 411 be published in the report of the commissions. Several papers a have also been published in the technical journals summarizing the important results as regards tunnel ventilation and also with reference to gasoline losses in present-day motor car operation due to the general use of unnecessarily rich mixtures"

Oct 1, 1921

By G. W. Birge

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Westmoreland County for coking tests was based, in part, on estimates of the coal reserves by Dowd,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in thousands of tons, as follows: [ ]

Jan 1, 1957

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V =kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By Bill M. Stewart, Philip W. Patton, Curtis C. Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines we revisited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

By John C. Edwards

Several experimental programs were conducted at the Pittsburgh Research Center to investigate the level of mine fire detection and alarm capability possible using state-of-the-art technology. These programs involved comparison of the response and alarm time of optical and ionization type smoke sensors to smoldering and flaming coal combustion in a smoke chamber. Coal combustion experiments conducted in the smoke chamber demonstrated that a CO concentration of 5 ppm above ambient corresponded to an optical density of 0.022m1. For the four smoke sensors for which a continuous analog signal was available, a smoke sensor alarm was defined as the average background signal plus ten times the peak-to-peak noise. This alarm criterion resulted in the association of the alarm for three of the four sensors with a smoke optical density of 0.022m-1. and 0.033m-1 for the fourth smoke sensor. The smoke sensors used in the smoke chamber studies were incorporated into large scale diesel fuel fire experiments conducted under normal ventilation conditions in the Safety Research Coal Mine (SRCM) at the Pittsburgh Research Center. These experiments showed that a diffusion mode smoke sensor alarmed earlier than a diffusion mode CO sensor; and, based upon the measurement of the optical transmission at the location of a pump mode ionization type smoke sensor that a pump mode ionization smoke sensor alarmed at an average smoke optical density of 0.021m" for the twelve experiments conducted. A series of 30 and 330 kW diesel fuel fire intensity experiments were conducted under zero airflow conditions in the SRCM. It was determined that :(I) thermal sensors are inadequate at 30 m from a 300 kW fire;(2) a diffusion mode ionization smoke sensor can be more effective for mine fire detection than a diffusion mode CO sensor;(3) recommendations can be made for sensor spacing in a mine entry based upon the measured CO buoyancy induced spread rates along the mine roof and the time for a developing coal fire to ignite a conveyor belt.

By James L. Konchesky

Crushed coal, consisting of a wide range of sizes, was effectively blended by recycling it through a bin equipped with a particle distributor. Vertical blending was accomplished by simply recycling the coal; it was not significantly influenced by the horizontal blending that was achieved by the distributor. The method was effective, even though the coal was wet and possessed poor flowing characteristics. Recirculation appears capable of providing uniform blends of solids that can be more efficiently processed. Recirculation also appears useful, preceding packaging operations, to insure for blending of solids into specification products. Continuous measurement of the bulk density of the coal by a gamma ray meter proved to be an effective monitor of vertical blending effectiveness.

Jan 1, 1972

By M. Kanefsky, A. Q. K. Rajput

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties but on the precise shape of the cross-correlation functions between the noise inputs. By using two polarity difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 11, 1981

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By J. M. Gomes

The Bureau of Mines has investigated the occurrence and recovery of by-product heavy minerals from sand and gravel operations as a means of assessing the Nation's resources. Sand samples from 63 locations in central and southern California were treated to yield heavy-mineral concentrates. The mineral compositions of the concentrates were characterized by chemical and mineralogical examinations. Additional large quantities of concentrates were prepared from selected deposits that contained significant quantities. Beneficiation studies were performed on these concentrates to recover individual mineral products. Gold was recovered by amalgamation; platinum-group metals and radioactive minerals by flotation; magnetite, ilmenite, and chromite by magnetic and high-tension separation techniques.

Jan 1, 1980

By Oliver Bowles

"A Product from Mica Mines.Mica commonly occurs in pegmatites which consist of large crystals of feldspar and quartz, mica constituting but a small proportion of the total rockMuch of the feldspar thus thro n out during the process of mining is pure and of high quality, end the Bureau of Mines has suggested that much of it could be utilized for ceramic purposes. Encouragement is given to such utilization by the fact that several mines now worked for mica were formerly operated for the production of feldspar. ""'here mines are not readily accessible to railroads feldspar utilization might not be feasible, for it is a much lower priced product than mica and cannot therefore bear as heavy transportation expense. '""here mines ire located close to railroads, however, such utilization would tend to reduce the cost of mica mining, and at the same time assist in the solution of the waste disposal problem.The Bureau has recently been informed that some of the feldspar from mica mines near Spruce Pine, N.C., is now being sold and shipped away. An extension of this by-product industry is to be recommended.A Mica Deposit in New York City.The Bureau recently received a mica specimen obtained from a. building excavation at 157th St. and Riverside Drive, New York City. The specimen was about 2 by 4 inches in size, and fairly clear though containing numerous hair cracks. It was obtained only 7 or 8 feet below street level. At greater depth and with more careful methods of excavation material of much better quality might be obtained. The material submitted could be used for mica washers but not for sheet mica. It is stated by an official of a prominent mica company that many such fragments are obtainable in this locality and the possibility of the occurrence of a good mica vein is thereby suggested."

Jun 1, 1920

By James A. Morgan

FIELD MEASUREMENTS OF NOISE WERE MADE ON THE PERIPHERY OF ENCLOSURES DESIGNED, MANUFACTURED AND INSTALLED BY INDUSTRIAL ACOUSTICS COMPANY, INC. ON THE SECONDARY TACONITE CRUSHER AT THE JACKSON COUNTY IRON COMPANY PLANT IN BLACK RIVER FALLS, WISCONSIN. NOISE REDUCTION ACHIEVED BY THE ENCLOSURES WAS SUFPICIENT TO PERMIT REDUCTION OF CRUSHER ROOM NOISE TO 90 DBA, PROVIDED THAT OTHER SOURCES ARE APPROPRIATELY TREATED AND ACOUSTICAL ABSORPTION IS PROVIDED IN THE CRUSHER ROOM. SECONDARY CRUSHER NOISE WAS REDUCED 10 TO 15 DBA BY THE ENCLOSURES.

Jan 1, 1980

By L. C. IlsLey

The observations made by Bureau of Mines engineers of permissible equipment installed in about 40 mines have indicated a chance for improvement in designs calling for the use of bolts , screws , studs , etc. , especially with respect to bolt sizes and protection from mechanical injury .

May 1, 1931

By John H. Soulé

"INTRODUCTION The Mining Branch of the Bureau of Mines has used the wagon drill to sample mineral deposits in New Mexico. This method of sampling was successful and con¬stituted an important phase of the work on five exploratory projects undertaken in 1943, 1944, and 1945. The deposits varied in topographic features, geology, mineral content, and in the physical characteristics of the rocks drilled. The altitudes ranged from 630 to 7,800 feet. Three hundred and seventeen holes totaling 6,852 feet were drilled. The deepest hole was 66 feet; the average depth was a little less than 22 feet.The results of the above-mentioned work form the basis of this report. Special attention is given to the later and more improved techniques used. This report was written with the expectation that the procedures might prove advantageous to others in the exploration and sampling of near-surface mineral de¬posits, and that a more extended use of the technique might result.AcknowledgmentsAcknowledgment is due Charles H. Johnson, chief of the Rolla Division, Mining Branch, for helpful suggestions in starting this work, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, W. R. Storms, engineer-in-charge of the Silver City, N. Mex., Field Office, and Donald H. Mullen, mining engineer attached to that office, for assistance in preparing and editing this report."

May 1, 1947