Search Documents

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By W. J. Fene, H. B. Humphrey, J. J. Forbes

"INTRODUCTION Loss of life from coal-mine explosions in the United States in 1949 was the lowest in any year since before 1870. Although fatality reports from coal nines before 1910 were incomplete,' the explosion fatalities from single disasters or individual States exceeded the 1949 total in each year as far back as 1870, when the records become fragmentary. Since 1890, the only other year in which fewer than 35 were killed was 1946, with a total of 32. Figure 1 shows the total yearly fatalities from explosions in all coal mines and those in anthracite mines alone since 1870. The fatalities in bituminous coal mines were not completely reported before 1910, but enough reports were issued by major coal-producing States to compile reasonably representative figures back to 1885. Any corrections would be additions to these totals.The reason for the moderate total of 46 explosion fatalities in 1948 and the low total of 8 killed in 1949 is thought to be the serious and careful attention devoted to elimination of coal-mine explosion hazards after the disastrous explosions in 1947. The standards now being observed generally with respect to ventilation, rock-dusting, and inspections for gas are better than those found earlier in even the mines having the best reputations for safety. Exceptions are still numerous, but they are fewer, month by month, because of the pressure of Federal and State inspections and a changing conception of the hazards that should not be permitted underground. The prevailing precautions have not eliminated all ignitions of gas or dust, but they have limited propagation to small explosions and have prevented serious loss of life.The number of ignitions (14) reported for the year was less than the average (24) for the 5 years 1944-48 and only half the average for the fiscal years 1929-44. Another favorable factor is that Bureau of Mines representatives were probably in closer contact with both small and large mines in nearly all coal-mining districts. Inspectors now assigned to individual districts are better able to keep informed on the happenings and the progress of safety in their districts. In 1948, one-fourth of the explosions were in mines that employed fewer than 10 men; this condition was duplicated in 1949."

Jul 1, 1950

By N. F. Le Jeuns

For a number of years the Bureau of Mines has conducted semi-annual surveys to determine the changes in motor gasoline being sold in the United States. It was pointed out in the previous survey that there was an apparent tendency toward greater uniformity in the character of gasoline marketed in the United States. This practically uniform tendency which continued from April, 1917 to January, 1923, has been interrupted in the, present survey, as shown by an examination of the column marked "Difference," as given in Table 1. The figures in this table were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10% ,(85 samples) having the highest end points and the 10% having the lowest end points mere grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10%" and the ?Minimum 10%? respectively. The same process was used on the other surveys.

Jan 1, 1923

By Jerry W. Ramsey

The Bureau of Mines studied two Pennsylvania anthracites using low-temperature carbon dioxide adsorption. A modified form of the Brunauer-Emmett-Teller equation was used to calculate specific surface areas. Two mesh sizes of each anthracite were used to determine how gamma irradiation at 106 and 108 rads, both in vacuum and in the presence of air, affected the carbon dioxide surface areas. Results show that anthracites have a system of pores that are essentially all interconnected rather than isolated; that anthracites differ from one another in specific surface, which may correlate with density; and that irradiation in vacuum has no discernible effect on specific surface of anthracite, but irradiation in air does produce changes in specific surface.

Jan 1, 1966

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgica1 and" chemical methods to recover valuable constituents from metallurgical dusts and slags. Under this program a technique was developed to recover iron from molten copper smelting furnace slags by carbon injection. Slags from gas-fired reverberatory and electric copper smelting furnaces were treated in an 800-kva electric-arc furnace by injecting coke breeze into the bottom of the molten bath. Over 95 pct of the iron and over 90 pct of the copper contained in the smelting furnace slags were recovered, while up to 85 pct of the carbon injected into the system was utilized. It is anticipated that the metal product containing approximately 95 wt-pct iron and 2 wt-pct copper will be a satisfactory medium for recovering copper by cementation.

Jan 1, 1977

By Oliver Bowels

Many inquiries are received by the United States Bureau of Mines for the names of elementary books on geology, mineralogy, methods of identifying minerals, prospecting, and similar subjects. In response to this demand the following brief bibliography has been prepared. As many of the inquiries are received from those who have limited technical knowledge of the subjects involved, the bibliography includes the simpler texts which present the subjects in nontechnical language. Other texts contain glossaries which define the technical terms used. A short note following the title indicates the character of each book, the number of pages, and the price. Thus, elementary mineralogists or geologists, prospectors, mineral collectors, nature students, or travellers may select the texts that best suit their requirements and their capabilities. To supply the needs of more advanced students, quite a number of the standard texts used in schools and colleges are included in a second group. A short list of books on economic geology and mineralogy has also been added.

Jan 1, 1929

By J. H. Perkins

The Bureau of Mines has conducted desorption work on fine coal particles at near atmospheric pressure. An apparatus Iris been developed that uses a capacitance manometer to measure desorption of methane from coal particles up to, 2 inches in diameter and pressures up to 1,000 psi. This will make it possible to duplicate the desorption process as it occurs in its natural underground environment.

Jan 1, 1969

By R. A. Keaens, L. C. IlsLey

For the purpose of this paper a junction box is defined as " a fused switch, inclosed in an explosion-proof compartment, provided with a ready means of connecting or disconnecting a trailing cable without exterior arcing." Junction boxes are intended for use &apos;at the end of trailing cables and are usually placed outby the last open break through in a coal mine. Where it is not safe to supply current through nips or a trolley, junction boxes suitably spaced along an entry permit tramming and movement of machines with safety, although not with any considerable speed. Junction boxes serve a threefold purpose: (1) They prevent dangerous arcing at the outby end of trailing cables; (2) they afford a safe, practical means of fusing or otherwise protecting the trailing cable; and (3) they provide an efficient means of transmitting power from the power circuit to the trailing cable. The first purpose is the most important from a safety standpoint. Dangerous arcing-that is, arcing capable of igniting gas-frequently takes place where trailing cab1c.s are attached to the power circuit. At either 250 or 500 volts only a very small arc is required to ignite mine gas. The usual method of connecting the trailing cable to the power circuit by cable nips or trolley taps does not make a good electrical connection; hence arcing may be expected at any time. Furthermore, junction boxes eliminate the personal hazard attendant upon the use of trolley taps by removing the possibility of accidental contact with trolley hooks or wire and the liability to injury due to manipulation of the device. In the general scheme of mine ventilation it is assumed that gas will not accumulate where junction boxes are placed, an assumption based on the normal operation of the ventilating system. In many

Jan 1, 1929

By G. Nuñez, M. A. Pathak, C. F. Stanley

"A 1986 report by the U.S. National Committee on Blomechanlcs (1) describes lung disease as a major national health problem. The report cites three areas that would benefit from a better understanding of the vibratory patterns of the lung. These areas are outlined below.1. In cases of respiratory distress, pressure driven artificial respirators are used. A new technique using high frequency respiration is quite promising, but the pressure distribution in the lung as a function of frequency is not yet known. At these frequencies of 1 to 60 Hz, the lung expands asynchronously (2) and a better understanding of these expansion nonunlformltles could provide valuable Information about the mechanics of high frequency ventilation.2. Listening to the sounds In the lung can yield valuable Information about the state of the lung. To improve the technique, a better understanding of how acoustic waves propagate through the lung is needed.3. The response of the lung as It Is subjected to acoustic excitation, dynamic loading or shock waves is not well understood. A better knowledge of these responees can lead to improved treatment for patients subjected to either explosive pressure waves or car crashes.4. Researchers are measuring the acoustic Impedance of the Iung to detect early states of dysfunction. Sneckenberger and Whitmoyer (3) have reported Impedances obtained at acoustic frequencies up to about 6000 Hz. However, It la not certain which parts of the lung are responding to the acoustic excitation.To Investigate the vibratory characteristics of the lung, excised rat lungs were excited via the trachea with acoustic waves at frequencies up to 6000 Hz. Thie paper describes an Instrumentation system, utlllzlng time-averaged holographic Interferometry, to detect and quantify the response of the lung surface to the acoustic excitation."

Jan 1, 1989

By P. A. Surgeon, R. R. Sayers

It is not the purpose of this report to try to describe all the work done during the past year for the improvement of health or the prevention of illness among miners , but to call attention to a few of the more outstanding investigations in which progress has been made . Among these , the investigations on the physiological effects of carbon monoxide , dust and ventilation , and temperature and humidity will be discussed . Carbon Monoxide . During the years 1920 and 1921 , much more work has been done on the various A survey phases of carbon monoxide than has been carried on for a number of years . of carbon monoxide poisoning in the American steel works , metal mines , and coal He conmines was made by Dr. Henry S. Forbes , of the Harvard Medical School . ** cludes from his survey that late after- symptoms following acute severe gassing rarely occur , and that almost always there is evidence of pre - existing pathological conditions when such effects do appear . He further states that he found no evidence of cumulative harmful effects resulting from frequent exposure . Dr. Forbes , Dr. Forbes , assisted by Louise Hompe , made a laboratory investigation in which anesthetized animals were exposed to carbon monoxide , illuminating gas , and benzol *** . The investigators conclude that , under the conditions of their experiments , there is no change in the coagulation time of the blood . It has been stated by many investigators that the blood of those affected by carbon monoxide does not clot as quickly as normal blood . While the investigation referred to above may not cover all the conditions , it is a valuable contribution to the subject as it indicates that the small hemorrhages found in the membranes covering the central nervous system , abdominal organs , etc. , at autopsy of those dying of carbon monoxide poisoning is probably not due to direct toxic action of the gas upon the blood .

Feb 1, 1922

Develop a method to evaluate the effectiveness of coal scam fire surface seals so that potential problems may be corrected at an early stage, before the integrity of the surface seal is lost. Background Surface seals are the primary coal seam fire abatement method being used in the western United States. Surface seals smother a fire by denying it oxygen. The seal is usually constructed by placing a mantle of soil, four to ton feet thick, over a coal scam fire area to exclude air from the fire. The soil is compacted to increase effectiveness, and a soil cement may be used to augment the soil. In some cases, burning coal may be excavated and separately smothered or otherwise extinguished in another area; in other cases, a trench maybe excavated and backfilled with incombustible material to isolate a fire. More often, a surface seal is simply applied over and around the entire known burning area. In the 1950&apos;s, the Bureau of Mines administered a large program to treat numerous coal seam Fires across the western United States. Methods used in this program were described in Bureau of Mines Information Circular (IC) 7932, dated 1959. More recently however, various coal seam fires have been treated with surface seals under the direction of state Abandoned Mine Land Reclamation authorities. It has frequently taken years to evaluate the effectiveness of surface seals. By the time problems become evident, it has often been too late to take corrective action within the scope of the original abatement project. For this reason, the Bureau of Mines developed a means for tracking temperature trends at coal seam fire projects to obtain a better and earlier handle on the effectiveness of surface seals.

Jan 1, 1991

By Ben E. Argyle

"The tungsten area in southern Mecklenburg County, Virginia, was studied by the Bureau of Mines during the period August 1944 to March 1945. The explorations were an expansion of the work done by the Bureau in 1943 in the tungsten area of Vance County, North Carolina, which joins Mecklenburg County on the south.3/Outcrops of quartz veins in the area were searched for and examined, and the only Promising showing found (a vein on the Gladys N. Taylor tract) was explored by trenching, test pitting, and diamond drilling (fig. 1).Mecklenburg County, Virginia, is in the southeastern part of the State, bordering on North Carolina,U. S. Highways 1, 15, and 58 traverse the County, and State and County roads provide ready access to most parts of the area.In 1942, Joseph and Richard Hamme discovered tungsten-bearing quartz veins in Vance County, Forth Carolina, and started mining and milling the ore. The first concentrates were shipped in July 1943. In August 1943, the Hamme holdings were acquired by Haile Mines, Inc., who continued the mining operations.The Bureau of Mines began exploratory work in North Carolina in June 1943. Reconnaissance work showed that the mineralized belt extends north-ward into Virginia. The Kimball tract, which joins the Taylor property on the north, was explored in 1943 by trenching and drilling by the R. G. Lassiter interests of Raleigh, Y. C., with disappointing results.The topography of the district is mature and characterized by wide, shallow valleys and low, rounded ridges. The main ridges trend northeast. Most of the area ranges from 300 feet to 400 feet above sea level.The relief apparently is controlled by resistant quartz lenses and the associated hard, silicified zones. The enclosing schists and granites are usually deeply weathered. Consequently, most of the quartz veins are found on the ridges."

Apr 1, 1946

By K. R. Farley

A simplified method for the atomic absorption determination of antimony is described. Samples are dissolved in hydrobromic acid and diluted to volume with water. Solutions can be ready for analysis in about 10 minutes and are stable for at least 24 hours. The spectral line at 231 nanometers is used, and there is no effect on absorption resulting .from the presence of any concentration of HBr. Absorbance is linear with antimony concentrations up to 120 micrograms per milliliter. Sensitivity is 1.48 micrograms per milliliter per 0.0044 absorbance. Relative errors on National Bureau of Standards Standard Reference Materials were 3 percent or less, and relative standard deviations on 12 determinations of each of three flue dust samples were 4 percent or less (95-percent confidence limit).

Jan 1, 1980

By L. G. Marsh

The manufacture of lubricating oils from wax-bearing crude petroleums involves the removal and recovery of the paraffin wax contained in the lubricating distillates. During this process several intermediate products are formed, among them the mixture of waxes and oils known to the refiners as "foots oil." Because of its complex character, foots oil is little understood, and therefore methods of handling it in refineries are often inefficient. The Bureau of Mines is studying the manufacture of lubricating oils, and during the work has investigated the redistillation of foots oil. This report gives in brief the results of the investigation, and recommendations based upon it.

Jan 1, 1926

By W. W. Adams

During the calendar year 1927 the United States Bureau f Mines conducted, for the third consecutive year, a safety contest among more than 250 mines and quarries. Aside from its underlying purpose to promote safety, the object of the contest was to learn which mine or quarry had completed the year&apos;s work with the smallest proportionate loss of time from accidents to its employees. Competing companies were grouped into five classes, namely, anthracite mines, bituminous teal mines, metal mines, nonmetallic mineral mines, and quarries and open-pit mines. To the winning company in each group was awarded the bronze trophy "Sentinels of Safety," the gift of The Explosives Engineer magazine. The winner in each group was the mine or quarry whose record showed the smallest loss of time from accidents in proportion to the total amount of time worked by 411 employees. This proportion is designated the "accident-severity"3 rate; it indicates the number of days of disability resulting from personal injuries per thousand man-hours of work performed by all employees. Each company&apos;s standing was determined by the Bureau of Mines from detailed records furnished by the contestants. Records of the leading companies were made known to a committee of seven men well known to the mining industry but not connected with the Bureau of Mines. This committee selected the winning companies in accordance with rules governing the Competition. According to the contest rules, the competition for the trophy was restricted to mines employing at least 50 men underground and to quarries and open-pit mines employing at least 25 men in the pit. As several plants fell below these figures during the year, their records could not be considered in connection with the award of the trophy. Figures covering these plants are, however, included in the attached tables.

Jan 1, 1928

By Basil Dimitriades

Five recently developed methods for determining nitrogen oxides in automotive exhausts have been evaluated from the standpoint of accuracy and applicability in current exhaust studies. Results showed that methods requiring conversion of nitric oxide to nitrogen dioxide as a part of the analytical procedure are subject to errors introduced by the instability of NO2. The extent of some of these errors has been determined and procedures have been developed to minimize undesirable influences. On the basis of the results obtained from this study, recommendations are made regarding procedures for batch type or continuous measurement of nitrogen oxides in exhaust streams.

Jan 1, 1968

By C. Q. Cupps

Rate of gas diffusion in reservoir oil has been investigated in an effort to explain the variation in oil characteristics observed in the Weber Sandstone reservoir, Rangely field, Colorado. Coefficients of gas diffusion were determined experimentally for the Rangely oil system and used in a mathematical simulation of gas diffusion during the probable life of the Rangely reservoir, estimated at 65 million years. The simulator involved solution of Fick&apos;s law for diffusion in two dimensions by the method of finite difference and successive over-relaxation. The results show that continuing gas diffusion is a logical explanation for the variation in oil characteristics at Rangely and that the pattern of gas distribution by diffusion in an asymmetrical reservoir will not conform to structural contours as originally proposed.

Jan 1, 1971

By D. E. Seizinger

The Bureau of Mines has developed analytical methods, primarily gas chromatographic, for measurement of exhaust oxygenates produced from selected simple fuels. The resulting data were used to estimate levels of carbonyls and noncarbonyl oxygenates in exhaust from gasoline fuels. Estimated noncarbonyl oxygenates in gasoline exhaust may comprise as much as 30 pct of total oxygenates which include unsaturated carbonyls and noncarbonyls believed to be significant potential pollutants.

Jan 1, 1972

By J. J. Forbes

The rapid increase in the quantity of coal being mined by stripping methods is one reason for the increased interest evinced by safety and other agencies in the hazards that are inherent in this Method of mining. The coal-mining laws of some States contain general provisions governing the mining of coal by open-cut methods, but none contains a complete list of specific safety regulations or laws for-the safe operation of such mines. The cool-mining laws of one State empower the head of the coal-mining inspection organization to proscribe regulations for coal-stripping operations and gave him the authority and power to enforce the rules and regulations promulgated by him.

Jan 1, 1944

By R. R. Sayers

Carbon monoxide poisoning is one of the most widely distributed and most frequent causes of industrial accidents . Carbon monoxide gas is a product of incomplete combustion , and since it is without color , odor , or taste , its presence is frequently unsuspected in many places where it exists . It is an ever present danger about blast and coke furnaces , smelters , and foundries . It may be found in buildings having a leaky furnace or chimney , and in buildings where a gas stove is used without a proper flue connection , such as is often found in tenements , tailor shops , and boarding houses . Hospitals receive annually a great number of victims of poisoning , either by accident or in an attempt at suicide , from artificial illuminating gas . People may be affected by leaks wherever water gas is formed or used . The exhaust gases from gasoline motors under average running conditions usually contain 5 to 7 per cent carbon monoxide , and sometimes as much as 13 per cent ; deaths from running an automobile engine in a closed garage are not infrequent . A similar danger may arise in operating gasoline engines in launches without sufficient ventilation . The gas is formed also in stoker rooms , in gun turrets on battleships , in petroleum refineries , and by the Lablanc soda process in cement and brick plants . In underground mines carbon monoxide may appear as the result of shot firing , mine explosions , or mine fires , and in tunnels where automobiles , coal or oil - burning locomotives are operated . In spite of the common occurrence of carbon monoxide poisoning there appears to be no uniformly recognized treatment for a person overcome by carbon monoxide . In the rescue work of the United States Bureau of Mines , however , a method has been developed which has been supported by laboratory investigation , and has proved successful in practical experience , over a period of years . As outlined in this article , the method is useful in the hands of first -aid men as well as physicians .

Dec 1, 1921