Search Documents

By Sathit Tandanand

Geological differences among various coalfields restrain the applicability of subsidence prediction using empirical approaches previously developed. The Bureau of Mines assessed data collected from 16 longwall panels in the Northern Appalachian basin. Attention was focused on the effects of rock lithology, excavation width, and panel depth on the subsidence factor. The results show that the subsidence factor can be expressed in terms of the width-to-depth ratio by a simple exponential equation, which has a coefficient tentatively considered as the subsidence index. This index varies with the lithology of a particular site, and can be expressed in terms of percent distribution of weak and strong rocks in the overburden.

Jan 1, 1982

By W. M. Dressel

Over 2 million tons of steel furnace dust containing approximately 100,000 tons of zinc and 10,000 tons of lead are produced each year. Recycling of the dusts would conserve mineral resources, lessen land area requirements for disposal, decrease pollution problems, and aid in solving our balance of payment problem. Steelmaking dusts can be pelletized and thermally treated to remove lead and zinc and to reduce the iron oxide to form metallized pellets. In laboratory tests more than 99 pct of the zinc and 85 pct of the lead was volatilized from the dust by roasting at 1,000° C in carbon monoxide. The volatilized material can be collected and treated further for lead and zinc recovery. Reduction and volatilization of over 95 pct of the zinc and most of the lead was achieved by roasting self-reducing mixtures of steel furnace dusts and high carbon steelmaking wastes in an inert atmosphere at 1,100° C. Over 80 pct of the iron in the resulting pellets was metallized.

Jan 1, 1974

By H. L. Gibbs

A portable radon monitoring instrument capable of making on-the-spot measurements of the radon gas content of uranium mine atmospheres was designed and constructed. The monitor was tested in the laboratory and in operating uranium mines. Good correlation was obtained between the monitor readings and radon measurements made on mine atmosphere samples taken in radon bottles.

Jan 1, 1973

To improve the reliability of the Bureau developed bore-hole gage now widely used to determine the absolute state of stress in rock. Approach Use the knowledge gained by extensive field tests to design a more rugged and reliable Instrument using lighter and stronger materials. How It Works The original gage consisted of a stainless steel cylinder 1-3/8 Inches In diameter and 10-1/2 inches long. The new gage is made from titanium. This lighter material reduces the weight of the gage by 43 percent, which enhances the gage placement and depth of overcoring in vertical up? holes. For added strength, the titanium case and placement end are now threaded to the gage body instead of using screw fasteners. Three pairs of strain gaged transducers are positioned to measure the diametral deformation of a 1-1/2 diameter borehole at 60-degree intervals around the Inner surface of the borehole. Each transducer consists of a beryllium copper cantilever with a strain gage cemented on each side. These transducers are secured Into the gage body by a tapered shank for minimal creep. The transducers opposite each other are wired together to form a 4-arm external bridge circuit. A pair of transducers is referred to as a component. Any deformation of the borehole, which occurs during overcoring, is detected by pistons which translate the motion to the components. Each

Jan 1, 1982

Coal miners, especially roof bolter and continuous miner operators, work in a hazardous underground environment where they are often exposed to poor roof conditions. Nearly 500 rock fall injuries are reported each year, and 99% of them are caused by rocks falling from between the roof bolts. These loose rocks that injure miners are usually just a few inches thick, but on average weigh 280 pounds. NIOSH has found that most rock fall injuries can be prevented by installing roof screen during the bolting cycle. Roof screen is a sheet made of steel wires in a grid pattern. When screen is bolted up against the mine roof, it provides far more coverage than any common surface control used in the mines today. Because more mine roof is covered, there is less chance that a rock will fall and injure a miner. The facts about roof screen are shown in the new NIOSH video entitled “Make It Safer With Roof Screen.” Using extensive underground footage, the 7-minute video shows how well screen keeps loose rock from falling in difficult roof conditions. Techniques for installing screen from both outside-controlled and walk-thru roof bolting machines are shown. The video also provides safe handling tips, best practices, and information about machine technology that can greatly improve material handling. Throughout the video, a coal mine safety manager and a shift foreman talk about the tremendous difference that roof screen has made at their mines. An instructional booklet supplements the video with additional information. It presents compelling data from mines that have practically eliminated rock fall injuries with a roof screening program. Other sections of the booklet discuss in greater detail roof screen installation, tips for manual screen handling, a material handling system for roof screen, and use of the personal bolter screen, which can be easily handled by one person. Screen specification and custom ordering are described, including the sizes of screen, grid sizes, reinforcing (indicator) wires, edge cut options, and screen strength. A list of additional sources of information is also provided. Nearly every mine eventually encounters poor roof. Screen is one of the most powerful control techniques available. This new video will help make mine managers aware of screen, and it can help them in developing a roof screen installation program. It also serves as an information source and teaching tool for safety managers and trainers. The video can easily be integrated into new miner training programs or annual refresher training.

Mar 1, 2005

By A. J. Strazisar

The Bureau of Mines conducted a laboratory investigation to study the effectiveness of low-pressure steam and water spray in suppressing respirable dust at the tips of a saw-type cutting wheel. Suppression efficiencies were found to be proportional to the amount of the water or steam applied at the cutter tips. For equivalent water output rates, a maximum efficiency of approximately 80 percent was reached for both steam and water spray. Results from the steam and water spray tests showed an increase in suppression efficiency with an increase in particle size of 1 to 8 micrometers. The data indicate no advantages for using steam as a dust suppressant.

Jan 1, 1972

By Jack A. Touseull

The Bureau of Mines has developed a simple stereographic method of analyzing the orientation of single and intersecting planes of weakness in vertical pillars of parallel symmetry. From this method, it can be determined if planes of weakness transect the full horizontal cross section of a pillar. A major finding resulting from this method was that intersecting planes of weakness can transect the full horizontal cross section of a pillar even though the individual planes do not. This paper provides step-by-step instructions for using this method.

Jan 1, 1977

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By Will H. Coghill

Titanium is a well-known component of bauxite ores, sometimes occurring in sufficient quantity to mace its recovery worth considering. This question has been raised by some of the companies lixiviating bauxite ores. At the East St. Louis plant of the Aluminum Ore Co., a subsidiary of the Aluminum Co. of America, the waste sludge discharged daily contains over 75,000 pounds of Ti02. The sludge is all through 20-mesh, and a large proportion is slime. A supple of the waste was deslimed so that a gravity-concentration test of the "sand" could be made. The Aluminum Ore Co. cooperated in the work and made the chemical determinations In order to anticipate the results of table concentration a series of specific gravity fractions (float-and-sink) was made with heavy liquids. Acetylene tetrabromide was used for a density of 2.95, methylene iodide for 3.33, and thallium formate for 3.78, and the double salt of thallium formate-malonate made the separation at slimed sample appears in Table 1.

Jan 1, 1928

By McHenry Mosier

The Bell mine operated by the Warner Co. at Bellefonte, Pa., has an annual production of about 600,000 short tons of high-grade limestone. Since 1924, shrinkage stoping has been the mining method. Horizontal, long-hole diamond-drilling for production in stopes was started with one machine in July 1946. It is now standard practice. The burden on the holes is 10 feet. Diamond bits are noncoring EX-size in both concave and pilot types. The two types have little difference in drilling speed at the Bell mine. The diamond drills are mounted on 3-inch single-screw columns. Diamond drilling shows a marked increase in efficiency at the Bell mine, compared to percussion drilling, with respect to tons broken per drill shift, tons broken per foot of hole, and tons broken per pound of explosive. The advantages of diamond-drilling blast-holes also include (a) improved safety, greater footage per drill shift, (c) better frag- mentation of the broken, stone, and (d) reduction in amount of barring down required in stopes because the working places are limited to slots which have a relatively small area.

Feb 1, 1948

By Travis Q. Lyday

Gold continued to dominate mineral production in the group of volcanic islands and atolls of Melanesia in the southern Pacific Ocean, which comprise the British Commonwealth nation of Fiji. The Fijian mineral sector, however, remained of minor importance in terms of export earnings, Government revenues, and employment to the economy of the country, which was primarily agrarian with sugar as its mainstay. The Vatukoula gold-silver mine on the north side of the main island of Viti Levu remained the largest and most important mining operation, as well as Fiji's only operating metalliferous mine. In October, Western Mining Corp. (Fiji) Ltd. (WMCF), a wholly owned subsidiary of Australian-registered Western Mining Corp. Holdings Ltd., increased its interest in the Vatukoula joint venture from 10% to 20% by exercising its option with Emperor Gold Mining Co. Ltd., also of Australia. The assumption of mine management operations at Vatukoula in 1983, with its attendant influx of additional capital and technological expertise, enabled WMCF to increase both efficiency and output at the mine during 1984. Higher output was obtained owing to an increase in underground ore production, which was partly offset by a reduction in opencut tonnage, as well as to modifications in the recovery circuit. Rate of recovery increased from about 15% to over 82% of the gold contained in the ore and from about 40% to 45% of the contained silver.

Jan 1, 1986

By an Slo, J. J. Forbes

"INTRODUCTION This is the first of a series of information circulars dealing with the control of roof and the prevention of accidents from falls of rock and coal. These circulars are being published to focus attention of the coal-mining industry on this most prevalent source of fatalities and injuries and to present factual information that should be helpful in reducing loss from these causes.Records of fatal accidents in the coal mines of the United States, from all causes, have been kept since 1906; during this period approximately 30,000 men have been killed by falls of rock and coal in the bituminous-coal mines, and more than 7,000 men have lost their lives in the Pennsylvania anthracite mines from the same causes. From 1906 to 1930, about 900 men were killed annually by falls of rock and coal in bituminous-coal mines, and about 200 men were killed annually in anthracite mines during the same 25-year period. From 1931 to the present time, the number killed annually from falls of rock and coal has averaged more than 500 men in bituminous-coal mines and about 125 men in Pennsylvania anthracite mines.Numerically the record of accidents from falls of rock and coal shows improvement, but on a percentage basis and on a million-man-hours-of-exposure basis little, if any, improvement has been made during the past 40 years. The cold fact is that, year after year, about 50 percent of all those killed in coal mines in the United States lose their lives from falls of rock and coal."

Apr 1, 1948

By Lloyd A. Morley, Robert Stefanko

This report was prepared by The Pennsylvania State University, College of Earth and Mineral Sciences, ' Department of Mineral Engineering, University Park, Pennsylvania, under USBM Grant No. GO-133077. The grant was initiated under the Coal Mine Health and Safety Research Program. It was administered under the technical direction of the Pittsburgh Mining and Safety Research Center with Mr. G. J. Conroy acting as the technical project officer. Mr. J. A. Herickes was the grant administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this grant during the period 19 June, 1973 to 17 June, 1975. This report was submitted by the authors on 18 July, 1974. This technical report has been reviewed and approved.

Jan 1, 1974

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory conducted a study of laser safety in potentially flammable environments. Researchers measured threshold igniting powers as a function of beam diameter for butane and propane-air mixtures by laser-heating targets placed on optical fiber tips using a 1064 nm laser. The minimum igniting powers for propane-air and butane-air were about 250 and 300 mW, respectively. Threshold igniting powers for propane-air were approximately proportional to beam diameter for beam diameters from 0.1 to 2.0 mm. Results suggest that relatively powerful beams may be used in these atmospheres without causing ignition, provided the beam diameter is controlled. Threshold ignition delay times using 91125 and 62.51 125 pm fibers were approximately proportional to the inverse square of the laser power. Ignition delays were about 45 ms or longer for laser powers up to 800 mW. Preproduction samples of a commercial optical fuse prevented ignitions under selected test conditions. A self-healing effect was observed for one sample. Comparisons are made with the results of other researchers. O 2006 Laser Institute of America. Key words: propane ignition, butane ignition, laser ignition, nonbeam hazards, fiber optic fuse

May 3, 2006

By Guy A. Johnson

This Bureau of Mines report summarizes the results of efforts to develop reasonably priced, reliable mine shaft fire and smoke protection hardware for metal and nonmetal mines. The hardware was incorporated into a viable prototype system that would minimize fire and smoke hazards. The design of the system had to be sufficiently flexible to be utilized in a wide variety of metal and nonmetal mine shaft and shaft station configurations. As a result of long-term, rugged field tests, an improved (second generation) system was developed. The hardware is now commercially available.

Jan 1, 1978

By E. O. Binyon

The Blue Metal corundum-andalusite deposit, in the Buckskin Mining district, Douglas County, Nev., was explored by the Bureau of Mines in 1945. The results of that work were presented in Report of Investigations 3895, exploration of the Blue Metal Corundum Property, Douglas County, Nev. published in August 1946. That report also describes the property in detail, giving location, ownership, history, geology, and data on beneficiation tests. Further exploration was carried on in April and Way 1947, the results of which are presented in this report. The work consisted of 175 feet of drift and crosscut, bringing the total to 398 feet of underground working, as shown in figures 1 and 2. The 23-foot drift, which was the last work of the initial project, was extended 99 feet northward along the shear zone, and three crosscuts, spaced at approximately equal intervals along the drift, were driven to country rock on the hanging and foot walls of the zone.

Jan 1, 1948

To provide a means for mechanically separating and recovering nonferrous metals continuously from non-magnetic reject material produced at scrap automobile shredding facilities. Approach The Bureau of Mines developed a water elutriator system that separates metals from shredded scrap auto-mobiles based on differences in specific gravities. A premium-quality product, containing aluminum, magnesium, lead, zinc die cast, copper, copper alloys, and stainless steels, is obtained. How It Works Mixed nonmagnetic reject material currently being separated at automobile shred-ding facilities is introduced onto the top of an upwardly flowing vertical column of water. The water, overflowing a weir in the top of the vertical column, carries with it the floating, lightweight waste materials, mostly combustibles, while the heavier pieces sink through the rising water. Medium-density substances such as glass, rubber, and heavy plastics are carried off through a side port, located in the upper third of the column. The cleaned, mixed metal product sinks to the bottom and is continuously removed from the base of the column with a bucket elevator having perforated buckets. All three categories of material are removed from the system on separate wire mesh belt conveyors. Most of the water drains through the belts into a holding tank and, after settling, is recirculated back through the elutriator column. The purity and recovery of the metal product are influenced by two elutriator operating variables: the flow rate of water through the vertical column, and the height of the overflow weir at the top of the column.

Jan 1, 1983

By H. M. Lawrence

The recovery of phosphate rack from the ores in the land-pebble district of Florida is a simple washing and screening operation. In the gashing plants coarse phosphate only is saved. Log-Washer overflows and screen-undersize products containing an appreciable content of fine phosphate are discarded. The phosphate grains in the material discharged to waste are generally finer in size than the mesh--14 to 20 mesh or 0.346 to 0.03 inch--of the finest screen in the washer. The operators state that the washers ordinarily recover from 50 to 60 per cent of the phosphate content of the matrix mined. Any increase that can be effected in the recovery of phosphate would be of advantage to the industry and would conserve the mineral resources of the country. In considering possible methods that might increase the recovery obtained in phosphate-washing plants the application of flotation, if it could be successfully developed, seemed to warrant investigation.

Jan 1, 1928

By Fred N. Kissell

Methane-flow and pressure data taken from a mine in the Pocahontas No. 3 coalbed are compared with flow rates from lump coal obtained in laboratory experiments. From this, it is concluded that the main source of gas is the intact coalbed rather than a "crushed zone" near the working face. The permeability and sorption capacity of the intact coalbed are calculated and gas emission rates are theoretically accounted for.

Jan 1, 1972

By Murray Weintraub

The Bureau of Mines investigated the aerodynamic factors that control the functioning of the blowcase devices used in pneumatic processes for dispersing solids. Alumina powder of 8-micron mass-mean diameter was placed in 0.75- inch-diameter by 10-inch-long cylinders} and a blowcase technique was employed. It was determined that dimensions and gas rates for discharging the powder from the cylinder by a stream of gas may be calculated by assuming a fluidization mechanism and extrapolating residues to a desired finite quantity or to zero at the terminal velocity. The state of agglomeration of a powder at discharge may be determined from measurements of the velocity required for zero residue.

Jan 1, 1967