Search Documents

By O. S. L. Bruinsma, M. J. Matsela, D. J. van der Westhuizen

The free ligand (FL) model is an intuitive model to calculate the equilibrium concentrations in solvent extraction (SX) based on the distribution coefficient (Kd) at infinite dilution and the fraction of free ligand available for extraction. In this work, the FL model is validated to account for co-extraction of Ni and for designing the extraction and scrubbing sections of Co/Ni separation in a base metal refinery. Cyanex 272 is employed as a selective Co extractant in the process to yield high purity Ni. To enhance the loading capacity of the extractant, 50 mol% of NaOH is pre-loaded into it. Experimental and FL modelling results show that four equilibrium stages are required to purify the 99% Ni feed to a 99.97% Ni raffinate. The 53.59% co-extract with 26.76% free ligand is purified with a reflux scrub of 30 g Co/L in one equilibrium stage to 99.01%, Co in the scrubbed extract. The FL model as well as the Co/Ni/Na-analysis of the aqueous phase confirm that in the scrubbing section, Ni in the extract is mainly replaced by Co. Finally, in the one stage stripper the Co concentration in the scrubbed extract is increased from 5.6 g Co/L in the extract to 30.5 g Co/L that is partially used as reflux scrub liquor.

Dec 11, 2024

By F. C. Harris, S. J. Gaab, J. Sattarvand, S. Duzgun

Underground mines are inherently dangerous due to potential hazards such as fires, explosions, and caving of rock. Although these events are rare, once they occur a speedy and safe egress of mineworkers is critical to survival. Static evacuation systems use exit signs or directional lines but can get obstructed or be hardly visible in smoky or dusty conditions. This paper presents the investigation of the effectiveness of a smart evacuation technology in underground mining, where a real-time guidance system leads individuals on an optimised path to the egress while avoiding danger zones, compared to conventional practices. Participants simulated an evacuation from a virtual reality mine, using the conventional system and the smart evacuation system with real-time guidance. The highest reduction in evacuation time using the smart method amounted to nearly 40% on average. Moreover, 83% of participants preferred the smart guidance system, and agreed that it could enhance safety.

Sep 1, 2021

By S. Ganguly, R. Kononov

Carbothermal reduction of manganese oxides and manganese ores in the solid state was studied in hydrogen, helium and argon at different temperatures, ore compositions and carbon to manganese oxide ratios. Wesselsore (South Africa) and two grades of the Groote Eylandt ore (Australia) with different level of impurities were examined. Ores were characterised by XRD, X-ray fluorescence, optical microscopy and scanning electronmicroscopy. Isothermal and temperature programmed carbothermal reduction experiments were conducted in a fixed bed reactor in a vertical tube furnace, with on-line monitoring of gas composition by the CO-CO2 infrared sensor. The reduced samples were characterised by XRD, SEM and LECO analyses. Extent of reduction was calculated using data on the off-gas composition, and LECO carbon and oxygen contents in the reduced sample. Manganese oxides in the ore were reduced to a-Mn and carbides Mn23C6 and Mn7C3 depending on the carbon to ore ratio. The reduction rate of manganese ores in hydrogen was higher than in helium and argon. Key words: Manganese, Carbothermal Reduction, Hydrogen, Argon, Carbon Monoxide, Helium, Kinetics.

Jan 1, 2007

By T. Tholana, P. N. Neingo

"Mining companies globally are currently facing severe economic and financial challenges. In addition to global challenges, the South African mining industry has to face other operational challenges that are unique to the country and which threaten the survival and competitiveness of the industry. Profit margins are being squeezed by rising costs and decreasing commodity prices, while labour productivity is greatly affected by intermittent labour unrest. This paper analyses how the South African gold mining industry has performed pre-, during, and post the global financial crisis of 2008. The competitiveness of the industry in terms of labour productivity and industry cost curve position is analysed for the period 2006–2013 to assess the impacts of both the global financial crisis and labour unrest. An analysis of the South African gold mining industry is presented at company as well as mine level. Productivity measure in this paper is limited to labour productivity, in line with limited reporting on productivity. All the data analysed was obtained from the public domain. IntroductionSouth Africa dominated the world as the number one gold producer until 2009 when China took that position, and today South Africa ranks fifth after China, Australia, Russia, and the USA. According to Statistics South Africa (2009), South Africa still had about 30 years of production in the gold sector, a forecast that fluctuates based on the day’s modifying factors. Although South Africa has a comparative advantage in terms of minerals endowment, there are challenges faced by the mining industry that hinder translation of the comparative advantage into a competitive advantage. The industry continually seeks to address these challenges to remain competitive in global markets while addressing national and community needs.Neingo and Cawood (2014) argued that stakeholders in mining are continually concerned with mine management’s ability to translate use inputs effectively into quality outputs. They further suggested close monitoring of effective utilization of people, materials, and money to obtain maximum production of commodities under given conditions. Productivity is measured in various ways, including unit cost, output per employee, and output per unit capital equipment"

Jan 1, 2016

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser

Reprocessing of historic gold tailings is a common activity in South Africa, while base metal tailings offer similar reprocessing potential. The historic base metal tailings of the Namib Pb–Zn mine (Erongo Region, Namibia) still contain valuable resources of Pb and Zn in carbonate-rich matter. Micro-analysis of primary ore minerals identifies some galena as argentiferous and sphalerite as the principal host of Cd. This study demonstrates that knowledge of primary ore mineralogy helps to reveal the hosts of valuable commodities (Ag, Cd) and that field-portable X-ray fluorescence tools allow precise and accurate determinations of major and minor elements like Zn and Cd in such carbonate-rich material. Although there are limitations to directly determine the contents of certain element (i.e., As, Sb, In), linear correlations allow prediction of the likely abundance of these elements. Providing that the inter-mineral and inter-element relations are understood and there is consistency in sampling and analytical methodology, portable X-ray fluorescence analysis is an effective method to evaluate the chemical characteristics of base metal tailings for a range of major and trace elements.

Sep 9, 2024

By N. R. Shoko, J. Chirasha

Zimbabwe Alloys has been producing Low Carbon Ferrochrome since 1953. A number of operational and technical advances have been made since then. Some of these advances improved production significantly. Process control, however, remained a challenge not only in the production process itself but also in the handling of finished product. In addition the handling of the slag created an environmental problem. Process control issues were addressed by Zimbabwe Alloys Limited and Japan Metal & Chemicals (JMC) entering into a Technical Transfer Agreement. The aim of the technical transfer was to improve production, alloy quality and, thereby, the financial performance of Zimbabwe Alloys. In addition, the Low Carbon Ferrochrome production process was made environmentally friendlier by modifying the final slag handling methodology. The aspects that are covered and discussed in this paper are, ladle refractory lining changes, improved control of the process, changes in the alloy casting methodology and granulation of the final slag. The improved control of the process was enhanced by the conversion from ladle duplexing to argon purging, introduction of on-line sampling and introduction of second stage process. The combined effect of the above was a significant improvement on on-grade material production, production efficiencies, unit cost of production and a cleaner working environment.

Jan 1, 2004

The visit which took place on the 18th February, 1972 was a departure in that the places visited had no direct connection with the work in which members of the Institute are normally engaged. It was refreshing and stimulating to see important and involved operations normally outside ones own trend of life and to have experts to speak about technical, financial and matters of general interest concerning their work, not forgetting their troubles and problems and how they overcame them. Carlton Centre The members of the Institute were received by Mr D. Appleton, Public Relations Officer of the Carlton Centre Limited, who introduced Mr L. R. M. Fee of W. Rhodes Harrison, Architect in charge of the project; Mr W. C. E. Skilton of Murray and Roberts, the Engineer in charge of the construction of the complex and Mr A. Home the Senior Operating Engineer of Carlton Centre Limited. Each of these gentlemen addressed the members giving short rundowns on the project with special reference to their particular sphere of the undertaking. A variety of particularly interesting statistics relating to the planning construction and the ultimate operation and maintenance of the complex was given. Mining engineers present had an opportunity to compare the problems encountered by them associated with depth to problems encountered by the civil engineer in the construction of a building rising to such an enormous height. To some of the members a sense of similarity of the labour problems encountered must have been recognised. After tea the visitors were divided into groups, each under the guidance of an official, and then visited the highest floor accessible and thereafter the 19th floor where the internal arrangements for airconditioning, lighting, plumbing, power supply and communication arrangements were explained. Thereafter a visit to one of the seven basements which houses all machinery required to serve this enormous complex enabled the visitors to see the standby power arrangements as well as the refrigeration plant. The visit finished in time to proceed to the Crest Hotel in Hillbrow for lunch. To our hosts for the visit to the Carlton Complex a special vote of thanks is recorded. Strydom Tower In the afternoon the party proceeded to the Strydom Tower where Mr Knight from the Public Works Department who was the Engineer in charge of the construction of the tower gave details on the construction and the extraordinary methods which had to be adopted to achieve the desired objectives and to overcome known as well as unforeseen difficulties. The comparatively short time taken to complete the project and the good safety record appeared to impress the visitors. The final phase of the visit was taken care of by Mr Bothma of Telecommunications Department of the Post Office, who gave an extremely interesting explanation of the telecommunication organization of the Post Office with particular reference to the part the Hillbrow Tower plays in the South African telecommunication system. Both gentlemen answered many questions willingly and interestingly. Following the explanatory talks the visitors were shown the technical equipment housed in the two top levels of the tower. Short explanatory talks gave members an insight into the workings of one of the most important aspects of modern life. Even to the amateur photographer opportunities existed to view and photograph the city from the highest available observation point. We are indebted to Mr Gouws, the Regional Director of the Post Office for granting permission to visit sections of the tower normally not accessible to the general public and to our hosts for the manner in which we were received and entertained on the explanation of the many interesting features of this important installation. In conclusion, the programme for the day can be classified as interesting, of exceptional educational value, and an opportunity to see something of the engineering skills put into two vast and ambitious undertakings and the results achieved.

By W. W. de Graaf, M. J. Ntsekhe

Klipspruit Colliery is experiencing coal losses, which leads to a negative impact on coal production and subsequently loss in revenue. This study aimed to identify the possible causes of coal losses in the No. 4 upper and lower seams. The objectives were to identify potential sources of coal losses through a literature survey, to identify areas where the coal losses occurred, to determine factors affecting coal losses, and to identify the most cost-effective methods to reduce coal losses. Highwall losses, top-of-coal losses, and coal edge losses were identified as the major areas of coal loss at Klipspruit. These losses were mostly attributed to the drilling and blasting practises of the pre-split, interburden waste, and the coal seams. Recommendations include re-visiting the current pre-split design and the tolerances adopted for the interburden and coal seam drilling and blasting design. It is furthermore recommended that Klipspruit implement a continuous improvement plan for the drilling and blasting and refresher training for the blasting crew and operators.

Jun 10, 2024

On 8th August, 1973, 57 members of the Institute visited Prieska Copper Mine at Copperton in the North Western Cape. After tea, the group was welcomed by the Management of the Mine, and Mr Grobler, the General Manager, gave an introductory talk. After they had been taken on a bus tour of the property, the members split up into groups and proceeded underground or to the concentrator. Of special interest to the mining members were the rock-handling methods in use at the mine. The stoping method that has been adopted is the continuous, long-hole sub-level open stoping system. The broken ore is moved with rubbertyred front-end loaders from the stope drawpoints to the ore passes. On the main tramming levels, the ore is collected by electric locomotives and discharged into the main shaft system at the bottom. At the shaft ore-pass system, a gyratory crusher that can accept rocks up to 1 m in diameter has been installed. The crushed product (minus 150 mm in diameter) will then be hoisted by a Koepe winder, which has a rated capacity of 900 tons per hour. The mine is also served by a declined roadway from surface, which facilitates the movement of heavy equipment. The most striking aspect is the productivity that can be achieved by the use of a trackless-mining system. For the production of 230 000 tons per month, it is estimated that 6 stopers and 7 developers will be required. The total labour force will be approximately 2500-2000 Bantu, 200 Coloured, and 300 Europeans. Training of maintenance and operating personnel is of the utmost importance, and it was interesting to note the extent to which non-White labour is being used in these occupations. Lunch was served at the single quarters, after which the group proceeded to the airfield for the return trip to Johannesburg. On behalf of the visitors, Professor de V. Lambrechts thanked Mr Grobler and his staff for the most interesting morning and for their hospitality,

Jan 10, 1973

By M. Rakoma

Following the blasting fatality on 17 December 2009, Landau Colliery was forced to change from the blasting practices that had been utilized since the start-up of the mine. Since then, attempts have been made to optimize blasting results. The challenge is rooted to the mining environment - during the early life of the mine, mining took place in virgin areas, whereas currently mining is taking place in areas overlying old underground bord and pillar workings. The underground bord and pillar workings aggravate phenomena such as spontaneous combustion, hot holes, and sinkholes. The 2009 fatality was attributed to hot holes causing premature detonation. Landau has been struggling with poor results from their overburden and coal blasts; leading to poor fragmentation of overburden and the PI parting that lies between the No.1 and No.2 coal seams. An extensive literature survey was completed in order to identify possible alternative solutions that could be evaluated for this unique mining environment, which demands a high degree of caution during mining to ensure factors such as dragline stability and personnel safety. The literature survey confirmed that the previous blasting technique, which was mainly characterized by air decking, was indeed the more efficient, although it was deemed unsafe because of the possibility of hot holes and the high sensitivity of detonators. Potential modifications to the blasting technique were modelled in a Microsoft Excel simulation that was available from the mine, and pit visits were conducted in order to determine whether implementation would be a problem. From the model it is evident that results can be improved by changing the current burden and spacing ratio. Visiting the pit revealed that the tie-in pattern and drilling inaccuracies are contributing to problem areas.

Jan 1, 2013

By S. Zhao, S. P. He, M. Y. Zhu, Y. Tao

"The effect of two refining slags (A: 1.0–1.8 CaO/Al2O3 ratio, 11–20 wt% SiO2; and B: 1.0–1.2 CaO/SiO2 ratio, 25–35 wt% Al2O3) on the inclusion morphology of a carbon structural steel (Q235B) was studied by controlling the balance between the steel and the refining slag at 1600ºC in a Si–Mo resistance laboratory furnace. The results showed that most of the inclusions in the molten steel balanced with slag A were formed by a lowmelting CaO–MgO–Al2O3–SiO2 system with a total oxygen content (T[O]) being fixed at 6–13 ppm. The inclusions in liquid steel balanced with the slag B were mostly formed by the CaO–MnO–Al2O3–SiO2 system, with T[O] controlled to 19–26 ppm. The overall size of the inclusions under balance conditions was higher in the steel reacted with the slag B than that reacted with slag A, with the latter showing more inclusions smaller than 3 um. In order to generate a large number of spherical CaO–MgO–Al2O3–SiO2 inclusions smaller than 3 ??m while decreasing the T[O] in the resulting steel, the composition of slag A should be used. This composition allowed improving the cleanliness of the slab, and is also advantageous for the castability of the molten steel. IntroductionThe sample used in this study was a typical carbon steel manufactured by CQ Steel. The galvanized, tinned, and plastic composite steel plates made of the original plates are used extensively for decorative panels, general dust pipes, drums, instrument cases, switchboxes, and train cars, among other uses. The target control composition is shown in Table I. The S and P contents are usually fixed during production below 0.020 and 0.025 wt%, respectively, with the aim of reducing longitudinal cracks on the slab surface."

Jan 1, 2017

Often plant performance suffers as a result of poor control. Poor control leads to low mill throughputs, poor classification and less than satisfactory concentrate grades and overall recoveries. By using the appropriate control tools, substantial gains in plant performance can be made. Mintek?s MillStar and FloatStar controllers have been implemented at various sites across the world. The MillStar controller incorporates leading technology that controls process units from the mill feed through to the flotation feed. Typical results show that milling circuit throughput is increased by 6-10 % and the final product grind size is tightly controlled, thereby enhancing flotation performance. The FloatStar controller is aimed at stabilising and optimising flotation circuits. Through improved level control alone, recovery improvements of up to 1 % have been achieved. Furthermore, by using on-line grade analysers, the controller stabilises final concentrate grades, whilst maximising flotation recovery.

Jan 1, 2005

By D. Weijie, S. Kai, Y. Hu, X. Ning, M. Shiyi, W. Junpeng, Z. Guihong, L. Xianjie

Flotation is one of the most important processes in the copper production industry. The copper grade in the concentrate is a pivotal indicator of the flotation process performance. However, it is difficult to achieve real-time measurement through hardware sensors. Based on the production data provided by an industrial operation, a novel soft sensor based on multi-layer perceptron (MLP) is proposed for effective monitoring of this pivotal indicator. The proposed soft sensor uses the nonnegative garrote (NNG) to perform global variable selection for MLP, while a local search (LS) approach is incorporated to improve the model presented by NNG. Simulation results show that the proposed algorithm has higher prediction accuracy and better model simplicity than other algorithms. Furthermore, the variables selected are consistent with the field experience, and the developed model can provide reference of feedback control for the optimisation of the process. Keywords: Flotation process of copper ore, nonnegative garrote, local search, soft sensor, multi-layer perceptron

Jan 1, 2020

By S. Rolseth, J. Thonstad

The traditional electrolyte for aluminium electrolysis is based on molten cryolite (Na3AlF6), acting as solvent for the raw material, alumina (Al2O3). Over the years there has been a trend to increase the content of excess aluminium fluoride (AlF3) to the cryolite-based electrolyte, in order to enhance the current efficiency of the process. In most cases one has ended up at 11?13 wt% excess AlF3because higher contents makes it difficult to control the heat balance of the process. This problem may be overcome if sensors are developed that will allow online control of electrolyte temperature and composition, and we may then see a surge towards still higher AlF3contents. In the development of new anode materials to replace the carbon anode with inert, oxygen-evolving anodes, focus is on anode corrosion, and a low electrolyte temperature is then highly desirable. While the conventional process operates at around 960°C, electrolyte temperatures as low as 750°C are being tested. This is achieved by having large excess contents of AlF3(40 wt%). The consequences of using such electrolyte compositions are discussed.

Jan 1, 2004

By J. H. Zietsman, M. W. Erwee, Q. G. Reynolds

Pyrometallurgical furnaces, essential for metal extraction, operate at temperatures exceeding 1600°C and represent complex multiphase systems that challenge direct industrial research. Multiphysics models play a key role in shedding light on their intricate behaviours, supporting the refinement of design and operational strategies. Integral to the operation are the tap-holes, which facilitate the removal of molten products and are routinely opened by lancing, a process comparable to the use of a cutting torch, where high temperatures result from oxygen reacting with an iron lance. When the lance pierces the clay, oxygen gas enters the furnace, which could influence the behaviour of the molten material inside. In this work, a multiphase fluid flow model was used to investigate bulk flow dynamics, with a focus on the effects of the lancing process on the inside of the furnace, immediately behind the tap-hole. Incompressible and compressible multiphase fluid solvers were used and compared with respect their performance – the intention was to assess whether using a compressible solver would yield a different solution to the incompressible one. It was concluded that there are negligible disparities in bulk fluid flow behaviour between the solvers for the case studies examined, indicating that solver selection might be less consequential for certain aspects of oxygen lancing.

Apr 16, 2024

By R. Thomason

Thank you Dr Barcza, President of the South African Institute of Mining and Metallurgy, for inviting me to share our experiences in Australia as regards the competency movement and my Association?s experience in assisting engineers become managers. This is my second visit to South Africa, and I am struck by the similarities between our countries. This extends to the professional issues associated with engineering and competencies in particular. I propose to outline two exciting stories today. ? Development of competency standards for professional engineers in Australia. ? Development of a management programme which has assisted professional engineers regain positions of leadership in Australian industry and government. First of all I would like to outline the Association of Professional Engineers, Scientists and Managers, Australia(APESMA).

Jan 1, 1997

By A. Nuric, S. Nuric, L. Kricak, M. Negovanovic, S. Mitrovic

"SynopsisRotary drilling with rolling tricone bits is the most widely used method for drilling large-diameter blast-holes in large surface mining operations. This drilling method is applicable to a wide range of soft to hard rock materials. This paper presents a fuzzy model for predicting the penetration rate of tricone rotary blast-hole drilling. The model is based on data obtained during the drilling of blastholes in rocks with various uniaxial compressive strengths in the Veliki Krivelj open pit mine, Bor, Serbia. The model was developed using the fuzzy logic toolbox of MATLAB with the Mamdani inference system. The fuzzy model was tested with 23% of the total dataset. The results obtained show the high reliability of predicting the penetration rates. Although there are possible limitations in applying the model to other open pit mines because of differences in rock properties, the prediction methodology applied in this paper can be used in many other predictions of the penetration rates.IntroductionAccording to Tamrock, rotary blast-hole drill operations depend on four important elements:•,Torque in the drill string drive sufficient to turn the bit in any strata encountered•,A high bit loading capability (pulldown force) sufficient for optimum penetration•,An air volume sufficient to remove chips generated during the drilling and to provide cool air to the drill bit bearings•,The selection of the proper type of bit for the material being drilled (Tamrock, 1984).The effects of rock mass parameters on the choice of the type of tricone bits were investigated by Kricak (1997)."

Jan 1, 2015

By R. E. Wilmot

This paper is based on the experiences, over many years, of numerous authors in the South African mining industry and of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and, when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a case where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions in a new mining operation and concludes with two follow-up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2007

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006