Search Documents

By J. M. Font, R. G. Reddy

Jan 1, 2004

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006

By A. T. Haile

Detailed monitoring of the response of the rock mass between rockbolt reinforcement units subjected to a simulated seismic source has been successfully conducted. This work has shown the increase in amplification of the Peak Particle Velocity (PPV) with distance from a rock bolt unit, and, a minimum PPV for rockburst damage for the given site characteristics. This understanding, at this site, will allow the design of a suitable rock bolt spacing to prevent unravelling of the rock mass between the rock bolt units for a given level of seismicity. Or, alternatively, an estimation of the requirement for a suitable fabric support system, for the anticipated level of seismicity, can be made.

Jan 1, 2001

By J. Björkvall, S. Ångström, L. Kallin

In this paper results from industrial trials of CaC2 injection during stainless steel production in an electric arc furnace at Sandvik Steel is presented. The main purpose of the investigation was to analyse the effect of the injection on slag foaming and final chromium oxide concentration in slag. The results show that both an increase in slag foaming and a decrease of the final chromium oxide could be obtained during the charges with CaC2injection. On the basis of the results, the economical requirements are also discussed. Both the technical and economical requirements could be achieved for steels alloyed with Mo. In order to secure the economical requirements for all steel grades of interest, the injection technology must be further developed. It would also be important to utilize the positive effect of the slag foaming on the electric energy consumption. The work has been performed as a part of MEFOS frame research programme with participants from Sandvik Steel, AKZO Nobel and Avesta Polarit. Keywords: stainless steel, EAF, slag foaming, injection, CaC2

Jan 1, 2004

By J. Nell

An overview is given of the matte melting process used for the beneficiation of South African Platinum Group Metal (PGM) ores. Most producers use six-electrode furnaces to melt the concentrate and Pierce Smith converters to oxidize excess iron sulphide from the furnace matte. Concentrates from two reef-types (the so-called Merensky and UG-2 reefs) dominate the feedstock supply. Concentrate from the Merensky reef is low in chromium and do not pose significant melting problems. Concentrates from the UG-2 reef contain much higher levels of chromium, which results in the formation of chromium-rich spinels during melting. This is attributed to the low solubility of chromium in furnace slag under typical operating conditions (an oxygen partial pressure of 10-8-10-9bar at temperatures of 1550°C to 1600°C). During the converting process care is needed to avoid excessively oxidizing conditions, which result in cobalt, nickel and copper losses to the slag. High nickel losses result in the formation ofFe2NiO4(trevorite), which often forms solid solutions with FeCr2O4and Fe3O4. In future, the main challenge in the processing of South African PGM ores will be to cope with ever increasing levels of chromium in the concentrate. A short-term solution to the problem would be to melt the concentrate under slightly reducing conditions to promote the formation of CrO, which is more soluble in the slag than Cr2O3. A longer-term solution to the problem would be to abandon the current matte-smelting process in favour of an alloy-based process, which would offer total flexibility with respect to the amount of chromium that can be tolerated in the feed. Key words: Merensky, UG-2, furnace, slag, matte, converting, spinel, chromium.

Jan 1, 2004

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm)vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599 m3/s to 0.01081 m3/s. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase hold-up was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold-up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase hold-up was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold-up with the dimensionless axial distance and the gas injection rate was correlated by using the modified Froude number. The experimental values of the dispersed phase hold-up were found to be in reasonable agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By G. van Aswegen

Seismic monitoring became commonplace in the deep South African gold mines in the early 1990’s. The discipline has, to a large extent, developed beyond the ‘research’ stage, and a ‘Guide to Seismic Monitoring in Mines’ has been accepted by the Department of Minerals and Energy1. Although ongoing research is a requirement for the achievement of all the objectives of seismic monitoring in mines, sufficient knowledge exists to apply seismic monitoring for routine seismic hazard assessment as an aid to risk management. The design and management of seismic monitoring systems can be tested against requirements spelled out in the ‘Guide’. Assuming the seismic monitoring system performs as per requirement, the best practice for routine seismic hazard assessment in mines includes • Long term seismic hazard assessment: through back analysis of seismic data and correlation with numerical modelling output, reasonable tests for planned mine designs are possible. • Medium term seismic hazard assessment: o Spatial analysis through contouring of seismic strain related parameters, with superimposed contours or event plots of stress related parameters allow the delineation of potential instabilities in space. o Quantitative and statistical analyses of seismicity in smaller spatial units (usually encompassing production sites) allow the comparative seismic hazard rating of different areas/sites so that rock engineering input and risk management can be optimised • Short term seismic hazard assessment relies mainly on time history analyses of particular seismicity parameters. The temporal patterns are controlled by a combination of temporal and parameter filters, the optimisation of which determines the success rate.

Jan 1, 2003

By R. G. Tarr

During an intense and accurate study of initiation systems used on an AngloGold mine, Mine A, poor drilling practices were revealed. Graphic results of all actual measurements taken are shown below. [ ] Accurate drilling of shot holes will determine whether a mining operation is payable or not and at what pay limit mining can take place. Losing 30 cm of a potential 120 cm-hole length will result in a number of consequences, i.e.: ?Higher stoping costs ?Drilling of one shot hole twice in every five shifts ?Increased explosive cost as a result ?Excess stress on hangingwall and footwall due to bad face shape ?Excessive blast damage before the area is worked out. No wonder we have such a high-risk operation. Drilling accuracy is crucial to the profitability on any mine as profits are directly related to the quality and utilization of the drilled shot holes.

Jan 1, 2000

By E. V. Lilford

The South African Minerals Development Act (?the Act?) has been promulgated and will come into full force and effect once it is gazetted. Thereafter, all Old Order mineral rights will have to be converted into New Order mineral rights within a 5-year period, probably by the end of 2008. The conversion of rights will be achieved only with the demonstrated inclusion of empowerment groups in the conversion applications. In addition to the Act, the first draft of the proposed Royalty Bill (?the Bill?) was released during the week beginning 17 March 2003. Comments on the Bill?s contents had to be submitted before 30 April 2003. The contents were to be considered in terms of applicability and acceptability to the South African minerals industry, where after proposed comments and suggested amendments were to be submitted to the relevant State Treasury office. Specifically referring to the Bill, the general response from the industry is one of concern. Since any royalty is tantamount to a tax, the general feeling is that the current mining taxation rates are already internationally competitive and to increase these effective rates, notably at differing rates depending on commodity type, will have an adverse impact on the South African mining industry. A number of these impacts can be mitigated to some degree, depending on the flexibility of the State to address the major concerns.

Jan 1, 2003

By Ravichandar. D., K. B. Nagashanmugam, M. S. Pillai

"Blast furnace performance depends strongly on the coke reactivity index(CRI) and coke strength after reaction (CSR) properties. An innovative and cost-effective method, known as the Salem Box Test, has been developed to prevent the mass production of inferior coke unsuitable for blast furnace use. This method consists of coal carbonization on a micro-scale and involves charging approximately 18 kg of coal blend in a stainless steel box, carbonizing it together with coal cake in the plant coke ovens, and testing the coke produced for CRI and CSR to determine its suitability for blast furnace use. Only coal blends that yield coke with CRI <25% and CSR >64% are permitted for mass production, and other coal blends are either rejected or the blending ratios adjusted in an attempt to upgrade them. The experimental results reveal that, for a given coal blend, the quality of coke produced by the Salem Box Test is comparable with that produced by bulk production, indicating that the test is acceptable as a screening tool for regular use. The present paper describes the methodology and application of Salem Box Test to predict the suitability of coke for blast furnace use at JSW Steel Limited, Salem Works (JSWSL), and illustrates its advantages in adjusting the coal blending ratio to produce superior coke, in detecting coal contamination, and in preventing bulk production of inferior coke."

Jan 1, 2015

By H. J. Glass

Collection, preparation, and analysis of blasthole chippings is expensive. Frequently, interpolation of grades at unsampled locations is considered using techniques like kriging. A pre-requisite for kriging is that an experimental variogram is established. In order to assess the quality of the experimental variogram, a measure is developed in this paper. The measure is derived from analysis of the time-honoured expression relating the variance, semivariance, and covariance. It reflects the weighted average deviation of the summed semivariance and covariance from the biased variance. The proposed measure allows assessment of the influence of key variables on the quality of the variogram. Using simulated data, it follows that the quality improves with an increasing number of samples, increasing density of the sampled locations, increasing regularity of the sampling pattern, and increasing uniformity of grades in the absence of correlation. Application to real data shows that the minimum number of samples could coincide with a marked decrease in the value of the measure. Establishing a threshold value is subject to further research. Keywords: variogram, variance, covariance, semivariance, minimization, sampling.

Jan 1, 2003

By C. M. van der Walt, J. F. van Rensburg, H. J. Groenewald

The South African platinum group metals mining industry faces considerable operational costs, with compressed air networks’ annual costs accounting for up to 35% of total electricity consumption. Amidst escalating electricity tariffs and volatile commodity prices, enhancing energy efficiency has become critical for economic sustainability. This study addresses the prevalent issues of mismanagement and inefficient use of compressed air on the demand side, such as leakages and unauthorised use for ventilation. While previous research has identified these inefficiencies, a gap exists in the continual monitoring and reporting of network performance to drive sustained improvements. This paper presents a practical solution developed and applied within a major South African platinum group metals mining group. The methodology focuses on a continual monitoring and reporting framework to improve demand-side management. The implementation of this solution has demonstrated significant financial and energy-saving potential. Key findings from case studies include: 1) the mitigation of R150,000 in costs over five days by rectifying a single instrumentation fault, 2) a potential annual energy saving of up to 5.6 GWh (R10.6 million) by enforcing valve closures during non-productive periods, and 3) an annual reduction of 3.7 GWh (R7.2 million) through improved underground ventilation controls. These outcomes underscore the value of a systematic, data-driven approach to managing compressed air consumption, offering a viable strategy for cost reduction and enhanced efficiency across the platinum group metals industry.

Mar 6, 2026

By G. S. Littlejohn

In anticipation of the flooding of an adjacent dolomitic groundwater compartment, five rough parallel sided boundary plugs at 58 and 50levels have been designed to resist safely hydrostatic heads of 1500and 1250 metres, respectively, over a service life of 100 years. Following a description of the engineering properties of the surrounding rocks, the paper details the design considerations relating to structural length and strength, hydraulic gradient, rock mass watertightness, constituent materials of mortar intruded concrete, pregrouting of permeable discontinuities within the surrounding rock mass, a bentonite barrier to resist aggressive mine water, plug tightening and design performance requirements. Routine quality control tests include permeability of the rock mass, fluidity, bleed and strength development of the intruded mortar, and temperature of the intruded concrete during curing. A special test programme includes determination of strength and stiffness of cored concrete and rock samples, shear strength of the rock/plug interface and associated in situ contact stress in order toe stimate the load safety factor against plug failure by shear.

Jan 1, 2006

By M. Reuter, C. Schuffeneger, T. Seppälä, L. Holappa

Reaction kinetics of solid-state reduction of chromite pellets (laboratory made and industrial) and lumpy ore was investigated by the thermogravimetric analysis (TGA) technique. Carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at both rising temperature and constant temperature in the range of 1450 - 1550°C. Scanning electron microscopy was employed to observe and analyse the structure and composition changes of the chromite samples. For the lab-made chromite pellets, the effects of particle size and bentonite addition on the reduction behaviour were studied. The pellet with smaller particle size gave a higher reduction rate. Bentonite addition had slightly negative effect on the reduction rate. When reducing industrial pellets, temperature and CO flow rate had positive influence on the reduction rate. Reduction of lumpy ore took place slower than reduction of a pellet. In all samples, chromite reduction proceeded longer in the outer part of the sample than in the centre part. The porosity of the chromite samples was determined before and after the experiments. The porosity of lumpy chromite increased significantly during the reduction. However, the porosity of lab-made chromite pellet decreases due to sintering effect. The reaction mechanism is discussed on the basis of experimental results and earlier investigations.

Jan 1, 2004

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 451 to 460 for the year ended 30 June 2002. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with statements of South African Auditing Standards. Those standards require that we plan and perform the audit to obtain reasonable assurance that the financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, ?assessing the accounting principles used and significant estimates made by management, and ?evaluating the overall financial statement presentation. We believe that our audit provides a reasonable basis for our opinion. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2003 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice. Auditors 29 July 2003 Council?s approval of the annual financial statements The annual financial statements for the year ended 30 June 2003 set out on page 451 to 460 were approved by the Council on 26 July 2002 and are signed on its behalf by:

Jan 1, 2003