Search Documents

By Alden B. Carpenter

The Dead Sea is the only relatively large body of surface water having bromide concentrations comparable to those in the brines of the Smackover Formation in Arkansas. The Dead Sea, like the Smackover brines, contains a great deal of calcium and is very low in sulfate and iodide. The relationships between potassium, divalent cations, and chloride indicate that over 20 percent of the bromide in the Dead Sea is derived from some source other than by the evaporation of sea water. A similar type of study of the Smackover brines in Arkansas indicates that approximately 60 percent of the bromide has been derived from some source other than sea water. Both the Dead Sea and Smackover brines are very low in iodide suggesting that the excess bromide has not been derived from organic matter. The origin of the excess bromide is probably the same for both of these brines, but the source of this bromide remains unknown.

Jan 1, 1978

By R. W. Bartlett

Computer deterministic models for predicting the time dependent extraction of copper by leaching fragmented rock (both in situ and heaped or piled) have been presented in the last two years by Bartlett1, Braun, Lewis and Wadsworth2 and Roman and Co-Workers.3 All of these models involve aqueous diffusion within the pores of the rocks from which the metal is being extracted. The rate of chemical dissolution of the ore mineral within the rock will also affect the kinetics in the case of sulfide copper ores and some of the more refractory oxide copper ores. Simulation is also needed for fine grain disseminated gold ores and low grade uranium ores that may be heap leached. The development of such leaching models has two major purposes: First, extraction estimates must be made for tong time periods particularly for situations where laboratory and field tests either cannot be made or where there is insufficient time for field testing. Second, the results of simulated leaching should indicate the relative importance of the extraction controlling parameters and, thereby, provide a better understanding of the complex leaching phenomena on heaped material being leached, and guide further experimental work.

Jan 1, 1974

By H. Barry Holt, Charles A. Bischoff

On November 15, 1990, President Bush signed the Clean Air Act Amendments of 1990. The new legislation is sweeping in its demands for cuts in smog, acid deposition, toxic air pollutants and ozone-depleting chemicals. The Amendments will siqnificantly alter air quality permitting and compliance and are estimted to cost billions of dollars to implement. This article provides an overview and summary of each of the eleven titles of the Amendments. It also addresses how the Amendments will be implemented.

Jan 1, 1991

By Ed H. Wipf, Kurt L. Bryan, O&apos

Flow sheets employing SAG Mills as the initial stage of grinding are commonly selected for comminution of ores. Several alternative technologies are available. The paper will provide a brief review of the latest alternatives to SAG mills. Included in this review will be a discussion of the comparable benefits of each technology. Commonly accepted disadvantages will also be presented.

Jan 1, 1998

When longwall equipment is being specified, a nominal capacity is generally given on which to base the design of the various face and out-bye systems and components. This capacity generally comes from a nominal annual capacity requirement based on realistic utilization rates. From illustrative examples of simple system simulation, this paper sets out to show that a single nominal capacity is not sufficient to size the different systems. The manner in which the Longwall is operated and the overall system configuration and availability can have a significant impact on overall productivity.

Jan 1, 2008

By Deepak Malhotra, Robert Dorfler

Modern engineering mill design has been refined over the years to the point where detailed ore and process specification criteria can be developed In the engineering design phase of the project. The plant Is then built to the detailed criteria and performance acceptance tested by the owner to see if the as-built mill meets the criteria, This performance testing is critical to the owner; the test must be systematic with sample collection coordinated throughout the plant. Despite the availability of systematic approaches to plant development, the new plants often fall short of design criteria. This paper discusses the key Issues a Project Manager/Process Engineer should Implement to ensure that plants meet design criteria.

Jan 1, 1991

By D. Murray

"The Mine Improvement and New Emergency Response (MINER) Act included the need for improved chemical technologies to address respiratory protective device inadequacies and refuge alternative development. The National Institute for Occupational Safety and Health’s (NIOSH) National Personal Protective Technology Laboratory (NPPTL) invests in research and development to improve the carbon dioxide (CO2) scrubbing technologies built into these mine safety systems. Testing at NIOSH NPPTL is performed using a custom-designed test system containing a chemical reactor and sensors in a constant flow of simulated expired breath to evaluate chemical performance for the scrubber materials. Current testing procedures focus on device duration or capacity, but do not report criteria needed to effectively optimize chemical performance. In this presentation, testing results which identify the chemical performance roles for CO2 scrubber components will be reported, and specific component chemical activities will be linked to both duration and CO2 absorption capacities. Chemical components being evaluated include hydroxyl, superoxides, metal, and amine active sites, distributed in salts, zeolites, metal-organic frameworks, and microporous materials. INTRODUCTION CO2 absorbents and oxygen sources are at the heart of closed circuit breathing air supply systems used in mining escape and rescue operations. CO2 absorbent technology was first developed for diving rebreathers and has been in use for over a century. Typically these devices include a soda lime formulation of pellets in the 8-12 mesh range. Larger 4-8 mesh particles are used in medical grade “low-flow” applications, since these particles present a lower flow resistance regime more amenable for use with resting individuals. Potassium superoxide and lithium hydroxide formulations are also used, where in each case the formulations involve bulk solid pellets or materials affixed to surfaces. CO2 capture technologies are now under intensive study in the energy and automotive industries, where the pursuit of optimal combustion processes has led to the development of new materials to capture, convert and store CO2, oxygen and carbon monoxide gases. Recent advances in nano-structured and high surface area catalysis have produced novel materials demonstrating chemical performance improvements in these industries, and these improvements may now also be adapted to enhance chemical efficiency and performance in escape and rescue devices. Higher surface area materials offer promise for improving the efficiency, or decreasing the burdens associated with the use of closed circuit respiratory protective devices containing CO2 absorbents. Novel chemicals that display advantages in chemical performance or decreased burden will be examined for inclusion in developing systems such as the next-generation closed-circuit mining escape respirator or refuge alternatives."

Jan 1, 2018

By Karel Rössler, Petr Vítek

"The Ejpovice tunnels in Czech Republic were built by EPBM in soft Clyashale, and in weathered profile with low soil overburden. The segmented liner at the cross-passage openings required support, which would not interfere with the EPBM clearance envelope during the scheduled pull back of the EPBM through both tunnel tubes. For that reason support frames or radial bolting could not be used. Steel rods inserted into the neighboring segments during the ring assembly, and later grouted were tested and realized as an innovative solution. The paper presents practical experience gained with the segmented liner support during cross-passages construction. INTRODUCTION An innovative solution using the grouted dowels was developed and realized for sixteen cross-passage openings of the twin Ejpovice Tunnels, whose construction was part of the railway track Rokycany – Plzen modernization. The following paper described practical experience gained with the innovative support of cross-passage openings, which was realized by short steel dowels grouted within the segments of the EPBM segmented liner. The paper is a continuation of the paper published in WTC 2015, which described the design aspects of the grouted dowels support, while the following paper concentrated on the production, and the performance of the dowel support observed during the breakout for the cross-passages openings. The connection by grouted dowels was patented by Metrostav, a.s. Company THE EJPOVICE TUNNELS CONSTRUCTION The Ejpovice tunnels construction started in 2013. The start of the high speed train operation through the tunnels was planned for 2018. The project was funded by the state government with the support of European Union funds of up to 70%.The tunnels were excavated with one EPBM (Earth Pressure Balanced Machine) with the external diameter of 9.89 m. The segmental liner inner diameter was 8.7 m, and thickness of 0.4 m. First, the South tunnel tube was excavated from the East portal, then the EPBM was pulled back through the South tunnel, and the excavation was started from the same portal for the North tube. After the South tube was freed from the EPBM excavation operations the cross-passage construction started. Due to the short time schedule, in the North tube the cross-passage construction started while the tunnel was still under construction. Therefore, the cross-passage construction was performed concurrently with the segments transportation, and with the EPBM pull-back through the tunnel. There were 8 cross-passages along the tunnels with a maximum distance of about 500 m, Fig.1."

Jan 1, 2016

By R. Mira, S. Rosa, P. Souza

This paper shows the historical data, local geology and mineralization, the mining methods applied, current production,, the planning staff, the resources of hardware and software available and the computer methods used. The activities are described starting with the driving of ramps/research levels, their dimensional parameters and positioning, driving of production sublevels with the same parameters plus those concerned with the stability of the rock mass during the development and the mining itself. Then, the detailing of the ore body is described together with the stopes planning, the openings stability analysis, and the drilling patterns and explosive types are discussed.

Jan 1, 1998

By A. V. Glembotsky, N. A. Greshnova, V. P. Seregin, V. A. Glinkin

Based on a new alternative depressant of zinc sulphide - dimethyldithiocarbamate- modern technology has been developed for the treatment of complex polymetallic ores. In addition to its general function (depression of sphalerite and iron sulphides to some extent), this double-acting reagent is a promoter for galena and silver minerals. Laboratory and plant tests, as well as industrial experience have all shown consistently higher silver recovery to the lead concentrate as compared with sodium cyanide, resulting in less pollution and a safer environment

Jan 1, 1995

By Mark W. Cadwallader

Heap leach mining requires liners in order to contain leaching solutions for both economic and environmental incentives. The use of HDPE geomembrane liners for heap leaching is discussed in this paper. Comparison is made to clay liners, with inclusion of economic considerations. Several heap leach projects incorporating geomembranes are discussed.

Jan 1, 1987

By Keith S. Olsen

Any discussion of barite mining is virtually impossible without considering, almost in the same breath, the many other variables, such as beneficiation, transportation, infrastructure and location that impact the economics of a particular barite orebody. My comments will be limited to just the mining aspects of barite orebodies and these observations must be considered in proper context with all other parameters affecting exploitation of a barite property prior to final decision on economic feasibility. In many instances low-cost mining situations are more than offset by high-cost beneficiation requirements. Likewise, there are cases of relatively high-cost mining associated with no or low-cost beneficiation requirements thus permitting economic exploitation. Barite orebodies and occurrences are almost as varied as the number of occurrences. As in most mining situations, the design of a mine plan and implementation of a proper exploitation program must be approached on a case by case basis. Proper and sufficient geologic control of a barite orebody must precede the development of a mine plan. Generally speaking, barite orebodies can and, at many times, do "strange" things; pinch with depth; almost never increase in size with depth, overturn, fault-off, change grade, etc. Due to the extreme variable nature of most barite orebodies, a mine plan and its implementation must be as flexible as possible. The ability to quickly adapt to variable conditions will greatly enhance the economics within a particular barite mining environment.

Jan 1, 1980

By Klaus Schönert

Experimental investigations of single particle and interparticle breakage show that the microprocess in mills demands an energy input between 1 J/g and 10 J/g, if particles below 100 pm have to be comminuted. A system analysis of grinding media and roller mills is given in respect to the energy supply to the microprocess and the influence of the back stream caused by the compression of the material inside the active volume. The back stream diminishes the probability for capturing the particles in very fine grinding processes. Some possibilities are discussed how to solve this problem.

Jan 1, 1989

By Alan D. Hoagland

The Flat Gap Mine is on Copper Ridge in the Appalachian Valley of East Tennessee, Large zinc orebodies occupy zones of solution and collapse breccias in lower Ordovician Kingsport limestone and dolomite, The principal ore mineral is sphalerite and the principal gangue is dolomite, The orebearing horizons are considerably more than 95% covered by thick residual clay, and geochemical prospecting under these conditions is an effective exploration technique which played an important role in the discovery and exploration of the Flat Gap Mine, The residual nature of the over-burden at Flat Gap is emphasized, Background heavy metals (mainly zinc) range from 50 to 200 ppm, and the anomalies range to 3000 ppm and more, About 80% to 9W0 of the soil zinc is in relatively insoluble form in solid solution with the hydrous iron oxides and in the crystal lattice of the clay minerals. Quite discrete zones in the soil with sharply contrasting metal value boundaries mark vestiges of bedrock mineralization, and such anomalous soil areas are often contiguous with partially weathered ore. It has not been possible on the basis of chemical criteria to distinguish between an anomaly formed from non-commercial mineralization and one formed from ore.

Jan 1, 1962

By R. L. Bleifuss, S. Zhong, H. E. Geotzman

Microwave heating of iron ore was investigated as an alternative to conventional reduction processes to solve the problem of slow heat transfer. Microwave heating and reduction tests were run on composite green balls made from coal and magnetite concentrate. Benchscale tests were run on both powdered and pelletized feeds using a 15 kW microwave generator. A significant increase in the reduction rate was obtained. With 20% excess stoichiometric carbon in the mix, more than 90% reduction of the iron ore can be achieved in about 10 min at temperatures of around 1,000°C. The reduction of iron ore with coal by microwave heating produces a pure, dust free, high-Btu flue gas that can be used in related thermal operations. Depending on the purity, the reduced iron product could be fed directly to an electric arc furnace for melting. In some cases, the removal of a slag phase may be required to eliminate excess silica and alumina.

Jan 1, 1997

By D. W. Fuerstenau

Experiments using an optically polished Pyrex disk and aqueous dodecylammonium acetate (DAA) films showed that the velocity with which the films recede increases markedly if the runs are repeated at short time intervals, where equilibrium cannot be reattained. This results from DAA molecules being desorbed from the disappearing liquid-air interface and being deposited on the solid-air interface being formed. Controlled experiments with Pyrex particles in a modified Hallimond tube showed a similar increase in flotation rate, again due to excess adsorption of DAA molecules that were transferred to the solid-air interface from the bubble on contact.

Jan 1, 2002

By Yiyin Ma, Yuqi Chen

Based on two in-situ measurements and mathematical analysis, the micro-climate in a large central underground pump and power station has been discussed in this paper. It is found from the research that the "semi- infinite" body model in the general heat transfer can closely represent the heat exchange process in the air flow-surrounding rock-adiabatic intermittent heat source complex in the station. Finally, computer simulations were made to calculate the micro-climate in a similar pump and power station where power machines operate intermittently. The simulation results are quite satisfactory. It can provide useful information for decision- making in the air conditioning of such stations.

Jan 1, 1991

The stability of mine roofs in permafrost zones is determined mainly by temperature and ice content. The deformation resulting from creep and temperature-dependent physical properties of frozen rock mass is the dominant component of total deformation. Roof bolts can consolidate the roof and control its deformation. In this paper, a finite-element model, for the analysis of the effects of roof bolting in a frozen rock mass is presented. The model includes the variables normally encountered when analyzing the effects of roof bolting in rocks. It also accounts for properties unique to frozen rock mass: creep deformation and the change in Young's modulus with changing temperature. The model shows that, as bolt spacing decreases, there is a trade-off between increased roof stability from increased mechanical support and decreased stability from increased conduction of heat into the frozen roof. This result was expected and shows that, for a given set of rock-mass conditions, including ice content, temperature, particle size, etc., there is an optimum bolt length and bolt density for minimum roof deflection.

Jan 1, 1997

By W. L. Han, Y. D. Zhang, X. C. Li

Meta-systhetic technique for large systems engineering has been placed on the agenda. The meta-systhetic A1 approach should involve the integration of digital and knowledge info, from qualitative to quantitative analysis, etc. Some algorithms of meta-systhetic technique such as ANN-ES and GA-ANN are introduced. A case study follows - mining conditions evaluation by meta-synthetic A1 methods, including: setting up the structure of evaluation indexes system, deciding their grade of membership by ANN-ES algorithm; determining the weight values of evaluation factors by GA-ANN algorithm; and developing the integrated evaluation model.

Jan 1, 2002

By R. R. Tatiya

The algorithms to model three stoping methods - sublevel, down- the-hole (DTH) and cut and fill stoping have been developed. These algorithms are capable of designing and performing economic analysis for one or more number of stopes in a continuous orebody. The design and economic analysis of each individual stope are first obtained. This is followed by the composite stope design layout and overall economics of the stopes under study. This paper describes only the stope design aspects of these models. The programs have been written using Fortran 77 with Tektronix graphical aids available at Imperial College Computer Centre (ICCC) London and are based on the basic data obtained from Khetri Copper Complex (KCC) and Rajpura Dariba (a zinc mine) in India. Minor modifications, however, may be necessary in some routines when used on other systems and for other mines.

Jan 1, 1989