Search Documents

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By F. L. Wilke

In the german hard-coal mining industry the mechanization of longwall faces and the machinery used for the extraction process have reached such an extent, that an extensive increase in productivity and face performance is not likely to be expected. At present, the greatest amount of man-shifts is needed for operations such as tunneling, transportation and haulage (fig. 1.). The most restrictive parameter, especially considering the possible ad- [ ] vance rate of faces, is the comparatively low advance rate achieved in drifting operations. Therefore improvements in productivity and advance rates of drifting operations will have considerable influence onto the extraction rate of the faces. The importance of drifting operations - and especially the so-called "conventional drifting by drilling and blasting" within the scope of long- term planning strategy of the german hard-coal mining industry is reflected by the development factor. This factor is given by the ratio: cubic meters of rock excavated in drifting per 1.000 tons saleable coal produced. In 1973, which is considered to be the beginning of the oil-crisis, this factor was determined to be 17.7 m3/ 1.000 tons sale- able coal.

Jan 1, 1982

By Peikun Liu, Guangyu Sun, Raja V. Ramani, Shambhu Sharan, Raman Srikanth, Bharath K. Belle

The contribution of the various outby sources to the contamination of the panel intake air has been the subject of a relatively small number of studies. In this paper, after a brief review of past studies, results from recent experiments on rates of contamination of intake air by outby dust sources are presented. Present study indicates that each outby source by itself may not be a major contributor. The loading point in the continuous miner section did not appear to be of major concern from contamination point of view. Belt entry including transfer point contributes significantly to the intake air dust level, though reentrainment was not a major source of dust. In longwall panels, the stageloader-crusher was the most dominant source. The panel-to-main belt transfer point was not a major source. Taken collectively, the contribution of all outby sources can be significant. In one longwall section, at the beginning of the longwall face, the contribution of all the outby sources and the headgate cut-out operation was observed to be about 80% of the permissible exposure limit (2 mg/m3). In modem high production longwalls, the application of effective dust control measures to reduce the dust generated from the outby sources is essential to achieve compliance with the dust standards.

Jan 1, 1997

By Wan-Kyu Choi, Arpad E. Torma

The electrochemical reactions involved in a zinc sulfide flotation concentrate leaching with sulfuric acid in presence and absence of Thiobacillus ferrooxidans, as well as with ferric chloride - hydrochloric acid containing media, have been investigated. The cyclic voltammetric measurements revealed that many intermediate electrochemical reactions are involved in the zinc sulfide leaching. Using chronoamperometric and chronopotentiometric techniques, it was found that the leaching process is controlled by solid - state diffusion. The activation energy of solid - state diffusion process was determined by the Price's approach to be 21.3 kJ. The leaching mechanism is discussed in terms of solid - state properties (energy bondings) of the high energy gap solid zinc sulfide semiconductor and energy density states of redox systems of acidic leach media. A generalized model for the mechanism of zinc sulfide oxidation is present.

Jan 1, 1990

By S. Mertikas

The purpose of this paper is to set the stage for (1) the determination of the specifications and actions required for a successful development of a system for the management of waste deposits and contaminants resulting from activities in the mineral industries and landfills and (2) the appropriate infrastructure to be developed at the industrial level. The design of this system would be such that its application could be extended to other industries as well. Waste deposits and contaminants from activities in the mineral industries and landfills commonly cause damage to the environment. In addition to precautionary measures aiming to protect against environmental impact, early warning and immediate response to mining hazards and contaminants is a requirement for sustainable development. Hazard detection and control requires continuous and real-time detection techniques, as well as methods for tracing and predicting the motion of contaminants and waste products. The efficient accomplishment of these goals in the minerals industry requires developing an integrated system for environmental monitoring using remote sensing technologies, in combination with advanced image analysis and geostatistical techniques.

Jan 1, 2003

By S. Lin, Y. J. Wang

Based on systematic definitions of a generalized multiple fan ventilation system, the concepts of an augmented system, its solution curve and the operating points of the original system are introduced. The Quasi-Newton algorithm is applied in combination with the switching-parameter method to ensure a continuous search along an augmented-system solution curve and identify all the possible system operating points on it. Two example networks are analyzed to demonstrate those concepts and the application of the algorithm for identifying operating points of multiple fan ventilation systems.

Jan 1, 1994

By L. Henry Smith, David C. Arthur

The Williams Mine is Canada's largest gold producer, with annual production of 14,000 Kg (450,000 ounces) from 2,300,000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs. The Mine Ventilation System is modified to include a new Vent Raise and Variable Pitch Vane-Axial Fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved. Heating costs associated with underground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, mine water and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors. System design, energy savings data and payback calculations are presented.

Jan 1, 1997

By R. Krishna

The basic ventilation equation of power equal a constant times quantity to the power three (P=constant x quantity3) makes it an extremely costly palliative as a long term measure. Provision of increased airflow is also limited by maximum tolerable levels of air velocity, the effect upon respirable dust and, in case of coal mines, spontaneous combustion. The paper high lights amelioration measures for climatic improvements at a lower cost. The paper has also shown a method for monitoring air pollution using laser technology.

Jan 1, 1997

By S. K. Mishra

Introduction The history of the Australian coal industry is almost as old as the history of Australia after new settlement. The first cargo of coal was exported from Newcastle to India in 1799. Coal has been mined in Australia for almost two centuries. But there are indications that the first coal was processed in 1877 in the Newcastle area. This is nearly 50 years after the first coal processing in Europe. Processing on any significant scale began in 1944 at the Newcastle Steel Works. In Queensland, however, coal processing did not begin until the second quarter of this century. The dramatic growth of mining and processing of Australian coal since the mid-60s is primarily due to the expansion of the export market in Japan, Asia, and Europe. Australian coals Black coal occurs in most of the major sedimentary basins of Australia. The better known deposits of commercial importance are in the Sydney, Bowen, Oakland, and Gailiee Basins. Apart from the Collie Basin in western Australia, other coal deposits of the Arckinga Basin in South Australia, the Bonaparte Basin in Northern Territory, and the Tasmania Basin are basically unexploited. The Sydney Basin of New South Wales and Bowen Basin of Queensland remain the major producers of black coal in Australia. Currently exploited or potentially commercial deposits of black coal in Australia occur in strata ranging in age from Permian to Tertiary. Estimated black coal reserves are summarized in Table 1. Coals from different ages have significant differences in their petrographic characteristics. Many of the Permian coals are usually rich in inertinite. Jurassic and Tertiary coals are typically rich in vitrinite content. Typical petrographic and chemical characteristics of some important Australian coking coals are summarized in Tables 2 and 3. The reserves of coking coals are restricted in the main to the Permian coals of the Sydney and Bowen Basins. Coal deposits in the latter are at shallow depth. A high percentage of these are being strip-mined. On the other hand, in the Sydney Basin, the majority of the reserves of good quality coking coals are at significant depth. The mining cost of these deposits is substantially higher than those in the Bowen Basin. It is usually possible to make strong coke with Australian Permian coals of vitrinite content much lower than the other international coals. But there are many major Permian deposits in Australia where low vitrinite content presents problems. As they are classified as marginal coking coals, optimization of their pro¬cessing plays an important role in meeting the market specifications of coking coal. The major reason for processing Australian coal is to reduce the ash content. Compared with British and some American coals, Australian coals are of relatively high ash content. Unlike American coals, more than 99% of the Australian coal deposits have sulfur content less than 1%. Consequently, sulfur control has never been a major problem. The coking quality of coal is improved simply through the ash reduction in the marketable product. However, with the increase in intensive mechanization and multi-stage handling of coal be-

Jan 9, 1985

By Jay Hilary Kelley

A ventilation system is described using dual aircourses: one zone occupied by working personnel, the other at the active working face. The two zones are separated by a partition or Shroud. The occupied zone to the rear of the face zone is ventilated adequately but with considerably less air because little gas, dust, or fumes are present. The face excavating zone is sealed and maintained at slightly more negative pressure preventing dust and gas generating from within to escape. Explosive mixtures within the face zone is rendered non-explosive by the introduction of inert gas therein. Each zone is vented separately to the outside of the mine. Because less total quantity of air is required for human breathing, etc, the total ventilation system can be drastically reduced in tan capacity, development entries, and air shafts, -- a great savings in costs.

Jan 1, 1991

By W. R. Hopkins

Over 95 percent of the world's refined copper is now produced by electrolytic processes. The bulk of this electrolytic copper comes via the conventional route for sulfide ores of concentration, smelting and electro-refining. A rapidly increasing percentage of world production is now achieved using hydrometallurgical routes involving dissolution of the copper values from minerals, purification of the resultant leach solution by solvent extraction and finally deposition as cathodes by electrowinning. The technology can now be considered mature and this paper endeavors to summarize recent developments which, from the authors' perspectives, are important.

Jan 1, 1989

By C. E. Jordan

The Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20-um size) in an effort to improve flotation efficiency in our domestic minerals industry. The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine particle, turbulent flotation model. For the mineral system investigated, improved flotation response was obtained under laboratory conditions by using small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1989

Overland conveyor belts that exhibit tracking problems under loaded and unloaded conditions can be tested to' determine the root cause of the mistracking. Moveable conveyors are more prone to mistracking due to structure alignment requirements. In addition, belting quality, splice straightness and carcass condition has a dramatic effect on the performance of a belt in relation to tracking. Methods are discussed that are proven to reduce belt mistracking and improve the operational reliability of the conveyor system.

Jan 1, 1995

Since 1992 the Grasberg Mine, located in the remote regions of Indonesia, has utilized the Modular Mining System. Over the last several years, major steps have been taken to maximize this productivity enhancement system. These steps include; the Automated Lineup, the Linear Program upgrade, tracking of Mean Time Between Failure, a MEDS system interface, a VMIS system interface, and implementation of the new Graphical Operator Interface Console with Global Positioning, This application of new technology and innovation has lead to improved performance, understanding and reporting, as well as the quality of the Indonesian Engineers. These efforts have contributed 10 Grasberg achieving one of the lowest mining costs in the copper industry.

Jan 1, 1998

Design models for belt conveyors used in mines predict both the belt power requirements and belt tensions. Conveyors with slightly downhill profiles are more complex to predict due to the way that models such as CEMA interpret friction. Performance of a particular conveyor in relation to other conveyors in the same system requires an analysis of natural stopping times, braked times and take-up location. A review of CEMA-based PC models is presented for design of underground multi-flight belt systems.

Jan 1, 1995

By Janusz S. Laskowski

The most important type of potash ores, sylvinite, contains sylvite, halite and a small percentage of insoluble gangue [sulfates (anhydrite), carbonates (dolomite), and clay minerals]. Primary normal long-chain amines are exlusively utilized to float sylvite from halite, but since mines are also adsorbed by insoluble slimes, the process requires prior desliming. This is carried out either by mechanical means, or by flotation of slimes and blocking off the adsorption centers on clays with the use of polyelectrolytes. Fractional crystallization is employed to produce fertilizer grade KC1 from disseminated ores with a high content of slimes. An extender oil is needed in addition to mine to float coarse sylvite fractions. The process is carried out in a saturated brine at mine concentrations exceeding the solubility limit and is strongly affected by temperature fluctuations. All these important features, which make this process differ from a conventional flotation, result from a high electrolyte concentration.

Jan 1, 1994

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By D. G. Abbott

This paper will describe the development, testing, performance evaluation, and in particular, the utilization for a mining application of revolutionary new mini-disc cutters for use in micro-tunneling and small-and medium-diameter tunneling or mining. It will begin by describing the engineering, testing, and development of rock cutting technology in conjunction with the Rock Boring Laboratories of the Colorado School of Mines. During initial tests, the five-inch cutters were able to penetrate limestone and welded tuff with compressive strengths of 9,000 psi to 24,000 psi. High excavation rates at low thrust and power were achieved with considerably less cutter wear than all previously available conventional discs. Eventually, the discs-with their modified carbide-insert cutting rings, high-load capacity bearings and cantilevered mountings-were able to facilitate the rapid and cost-effective installation of micro-and small-diameter pipes and tunnels in large cobbles and even solid rock, with compressive strengths exceeding 30,000 psi. This paper will also discuss the further development of the machine's cutter head and discs to full-scale site use on a range of tunnel machine sizes and soil conditions, including rock, boulders, and soft ground. Potential mining applications include the installation of tunnels to pro-vide ventilation, emergency escape routes, water drainage, compressed air, electricity, and sand-fill.

Jan 1, 1996

A thermomechanistic model was developed for the thermal decomposition of the enargite contained in a copper concentrate at 650° to 750°C in a fluidized bed with an inert atmosphere. At the particle level, the model permits one to predict the thermal profile inside the reacting enargite particles, as well as their thermal cycle. At the macroscopic level, a population-based model coupled to the bubbling-bed fluidized bed model allows one to predict the fractional conversion (dearsenification) of an enargite-bearing copper concentrate.

Jan 1, 2002

By K. R. Wood, P. M. Blythe, J. A. Finch, M. L. Lavallee

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1991