Search Documents

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By K. Chief

American Indian lands contain a vast amount of renewable and non-renewable resources that have consequently been mined (Smith and Frehner). Therefore, it is understandable that tribes are concerned about environmental impacts from mining and their ability to minimize and mitigate these impacts. This has created a need to better understand mining and its environmental impacts. The University of Arizona Superfund Research Program Mining educational modules developed educational modules for tribal colleges focusing on environmental impacts of mining, remediation of mining wastes, and sociocultural impacts of mining. Educational modules are independently packaged units of study designed to enhance the learning process and can be modified and adapted to different learning scenarios and objectives. In addition to providing specialized knowledge, the modules feature hands-on activities, incorporation of technology, student involvement, discussion, and exchange of ideas. Modules will aim incorporate traditional ecological knowledge and approaches that promote effective science learning for native students. Modules are designed to augment existing associates of science programs (e.g. biology, chemistry) currently offered at tribal colleges and can be modified for use in K-12 education and for non-tribal audiences.

Feb 23, 2014

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and Mineral Processing Systems (MPSI) merged, a unique opportunity occurred for two independent mill fabricators to compare design pro¬cedures and the research upon which they were based. Several semiautogenuous (SAG) mill analyses are compared using Boliden Allis and MPSI methods. The differences and similarities are then used in a correlation of critical stress definitions and the acceptable design and inspection criteria. Given the opportunity to compare the total philosophies and methods of several companies involved in the design and fabrication of grinding mills, it was important to first develop the comparison method and ground rules. One option was to compare analytical methods by details such as numerical techniques and accuracies. However, this option was discarded in favor of a more general approach. The question that was finally posed was in two parts. Given an identical mill requirement: • What would be the difference in the analytical design result, and to what aspect of the analytical process could this difference be attributed? • What would be the difference in approaches to obtaining the final hardware in subcontracting, both in specifying and Quality Assurance surveillance? By using this comparative approach, questions of relative conservativeness and reliability would automatically be answered.

Jan 1, 1992

By F. Mendaña

The characteristics of the igneous and metamorphic bedrock, extra-hard and abrasive, of the Guadarrama Tunnels, a bi-tube project of length 28.4 km without any intermediate attack, are first commented upon. Next, a detailed discussion is given of the most relevant aspects of the performance of the four double shield type TBMs. The experience of this leads to various recommendations to be borne in mind in future designs of TBM having to work in rock of similar characteristics.

Jan 1, 2007

By A. Kevin Beaton, Robert W. Laakso

The desire for dry passageways promotes the NATM as it provides a final support system most suitable for the installation of a waterproofing membrane. Waterproofing during construction is a cost effective way to enhance safety and function as well as increasing the life of an underground structure. The NATM approach utilizes the surrounding mass as an integral element of the "ringlike" support system. At the Pennsylvania Turnpike Commission Lehigh Tunnel No. 2 various rock classifications were determined to require support measures ranging from 2 to 12 inches of shotcrete along with spiling, wire mesh, deformed bar, lattice girders and rock bolts as needed. Field instrumentation and monitoring programmes are a key factor for the success of the NATM. When the support "shell" stabilizes smoothing shotcrete, waterproofing and a final liner can be placed.

Jan 1, 1991

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By S. E. Pérez-Fontes

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. The oxygen concentration in the process gas was set to 40% and 70% (by volume) and a heating rate of 40°C/min was used. Response variables included the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles and by thermochemical and mass balance calculations to reproduce the DSC and TGA data. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction as a function of time.

Jan 1, 2007

By Colin Rawlings, Simon Pepper, Maria Karakitsiou, John Mathews, Peter Townsend, Russell Bowler, David Keeble, Christopher Darton, Scott Sadler

National Grid needs to maintain a connection between two existing electricity sub-stations (Beddington & Rowdown) in the Croydon (south London) area, and allow the replacement of two 275 kV cable circuits that are buried under roads. This is to be achieved using a single 400 kV cable circuit within a 10 km (6.25 mile) long, 3 m (9.8 ft) diameter high voltage cable tunnel which is being driven through water bearing Chalk, at depths ranging from 5 m (15 ft) to 80 m (262 ft), with four access shafts(12.5 m (41 ft) in diameter) ranging in depth from 10 m (31 ft) to 40 m (131 ft). The Chalk in this area acts as a source of public drinking water supply (PWS) and is protected by areas designated Groundwater Source Protection Zones. To minimise the groundwater risk the design and construction of the cable tunnel and shafts has paid particular attention to the construction materials used, including testing of these construction materials prior to use, developing construction methods (including the design of the Earth Pressure Balance TBM) and maintaining a groundwater monitoring & testing programme prior to and during construction to ensure the integrity of the Chalk aquifer is maintained as a drinking water source. This paper describes the tunnel &shaft design and construction in relation to these particular groundwater environmental issues which set new precedents for tunnel assessment, design and construction requirements in the United Kingdom.

Jan 1, 2007

By K. Avarmaa, P. Taskinen

"The solubilities of rhodium (Rh) in a molten silver alloy in doré-smelting conditions for treating copper refinery slime at temperatures of 1,000 to 1,300 °C were measured using a high-temperature equilibration-quenching technique and direct phase analysis by electron probe X-ray microanalysis. The results obtained indicate that the solubility of rhodium in molten silver is very limited: only 0.04 to 0.26 weight percent at 1,000 and 1,300 °C, respectively. The thermodynamic properties of rhodium in molten silver were estimated from the solubility data. The compositions of the solid rhodium alloys in equilibrium with molten silver-rich doré metal were also measured in this study. The excess rhodium in the doré alloy will precipitate during the refining as solid, greater than 99 weight percent Rh.IntroductionSilver refining is a core step of the processes of anode slime treatment and precious metals recovery in copper refineries (Hait, Jana and Sanyal, 2009; Ludvigsson and Larsson, 2003). It separates the oxidic materials, such as nickel oxide (NiO) and barium sulfate (BaSO4), from metallics after the de-coppering and de-selenation steps of the anode slime, and refines the silver bullion from the undesired elements present (Cooper, 1990; Hyvärinen, Lindroos and Yllö, 1989). Doré metal is a silver-rich alloy which after the smelting step will be refined electrolytically, and the remaining constituents of gold as well as the platinum group metals (PGM) will be subsequently recovered in their own processing stages.Because of low concentrations of PGMs in copper, they are typically soluble in the doré metal in anode slime treatment. This can be concluded from their binary phase diagram data with silver (Massalski et al., 2007). One exception is sometimes encountered in the anode slime smelting operations if the smelter feedstock is rich in rhodium, as may be the case if the raw materials contain secondary raw materials such as e-scrap. The solubility of rhodium in solid silver is less than 0.04 weight percent (Królas and Sternik, 1995), and its solubility in molten silver is highly uncertain. The only experimental information in the literature (Królas et al., 1993; Elliott, 1985) suggests that the silver-rhodium alloy system at 960 °C forms a eutectic, which locates less than 2 °C below the melting point of pure silver (Arblaster, 2015). Early observations (Rössler, 1900) propose that rhodium is insoluble in molten silver even if solid silver-rhodium solutions have been recently produced on a nanoscale (Kusada et al., 2010).The aim of this study is to measure experimentally the solubility of rhodium in molten silver at doré metal smelting and refining temperatures. The silver alloy used to mimic the doré alloy contained silver and about 1 weight percent of the alloying elements copper, gold, palladium, rhodium and tellurium. The experiments were carried out in metal-slag equilibria with nitrogen-oxygen mixtures as the atmosphere, employing an equilibration-quenching technique and using direct phase composition analysis by electron probe X-ray microanalysis (EPMA) (Jak, Hayes and Lee, 1995)."

Jan 1, 2017

By George O. Lower

The use of cyanides in the extraction of gold and silver is well known.1 Such extractions employ con¬centrations of cyanide in the range of 0.02-0.25 % sodium cyanide equivalent in leaching cycles of 24-48 hours and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold and silver. 2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure. For example, on products in the flotation size range, the major portions (e.g. 65-85%) of the extractable copper frequently dissolved in 2-10 minutes. At coarser grinds, e.g. 100% minus 28 mesh and 100% minus 10 mesh, 75-85% of the total copper was extracted in 30 minutes.

Jan 1, 1966

By Dan Martz, Bill Moler, David Young, Wally Chen, Matthew Crow, Steve Norris, Tolga Togan

Two 610 m (2000 ft) long tunnels were driven through water bearing silts, sands and clays beneath the Sacramento River using a 4.59 m (15.1 ft) diameter Earth Pressure Balance Tunnel Boring Machine (EPBM). Four sheet pile shored shafts were sunk with and without dewatering. The pre-cast concrete segmentally lined and grouted tunnels were driven down at 6% grades beneath the river flood protection levees, buildings, roads, a railroad and adjacent to a Freeway Viaduct. Details of the schedule, cost, shaft construction, TBM, tunnel construction, and installation methodology for the twin1.676 m (66 in) steel force main pipes and environmental constraints are provided.

Jan 1, 2007

The latest in mining technology and equipment will be show-cased this month at MINExpo International 2004. The event, billed as the world’s largest mining equipment exhibition, is set for Sept. 27-30at the Las Vegas Convention Center. MINExpo, sponsored by the National Mining Association (NMA), is held every four years in Las Vegas, NV. This year’s event is expected to attract more than 40,000 mining industry professionals and executives from around the world. And several key members of the U.S. Congress and other senior government officials are expected to attend. In addition, senior industry and government officials from Asia, Europe, Australia, Africa and South America will be on hand.

Jan 1, 2004

By Raymond W. Henn

The 32nd annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 13-17, 2011. The field demonstration portion of the course was conducted June 16 at Baski Inc.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods per-formed under various field conditions. As part of the field demonstration, the class was shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and recorded conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results.

Jan 1, 2011

By C. G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX/EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to copper concentrates and ores will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of chalcopyrite concentrate treatment with this unique industrially proven process will be delineated.

Jan 1, 2001

By N. Loganathan, Tan Boon Tee, Joe O’Carroll, Richard Flanagan

In recent years, tunnelling activities in Singapore have increased considerably with the construction of extensions to the existing sub-surface transport system, a deep tunnel sewerage disposal system, and tunnels for the laying power cables and other utilities. These tunnels are excavated through urban areas, adjacent to high-rise buildings, depressed road structures, beneath other tunnels, and buried services. Earth pressure balance (EPB) tunnel boring machines (TBM) have been used extensively in Singapore with great success. The risk associated with soft ground tunnelling, including tunnelling through Old Alluvium, can be minimized with an understanding of the geology, geotechnical parameters, and the tunnelling-induced behaviour of Old Alluvium (OA The purpose of this paper is to present some design and construction aspects of EPB TBM tunnelling through Old Alluvium.

Jan 1, 2005

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN

Pressure losses in mine ventilation systems are estimated using friction factors and shock loss factors. The efficient planning and designing ofmine ventilation systems depend on the accuracy of the friction factors as well as the shock loss factors that are taken into consideration. While there is a much more acceptable knowledge of what constitutes friction loss in mine roadways, the shock loss factors are in general readily not available for all possible contexts of flow separation phenomena in mines. One such special case of shock loss in mines is the train of mine cars in the airway. Mine cars are widely used for the transportation of material, and the information on shock loss factor for mine cars is limited. This paper examines the pressure loss occurring due to a train of mine cars in an airway using scale model studies and numerical investigations. Computational fluid dynamic (CFD) studies are conducted using four different turbulence models. The performance of different turbulence models is analyzed by comparing it with the experimental results. The study suggests that the boundary layer resolution method is significant in the simulation of shock loss. From the study, it is found that the shock loss factors from presently available model overestimate the pressure loss by 7 to 15 times. A better prediction model for the shock loss factor of a train of mine cars in the airway is proposed using the experimental results.

Jul 24, 2020

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type, and causes of accidents in Turkish coal-extracting industries using Analytic Hierarchy Process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type, and causes of accidents. For this purpose, 1st, 2nd, and 3rd level hazards consisting of location, type, and causes of accident were determined by using the data of fatal mine accidents in underground and open-pit coal mining in Turkey between the years of 2010 and 2020. And then the data were categorized, and each category was prioritized using the AHP technique. According to the weights calculated by AHP, the most dangerous main criteria at 1st level hazards in underground coal mining is ventilation operations (0.363), while the most dangerous sub-criterion at 2nd level hazards is firedamp explosions and other gas accidents (0.409). On the other hand, in open-pit coal mining, the most dangerous main criteria at 1st level hazards are slopes and benches (0.575), while the most dangerous sub-criterion at 2nd level hazards are landslides (0.429).

Dec 30, 2023