Search Documents

By Joseph J. Diehl, Brian B. Khalighi

This paper discusses the Queens Water Tunnel, No. 3, Stage 2, being driven by a new Robbins High Performance (HP) Tunnel Boring Machine (TBM).The paper is divided into four sections. In the INTRODUCTION section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drive is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes, in the TBM OPERATION section, with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 1997

By Y. Okahara

The chlorination behaviors of pure iron and manganese oxides were investigated by combining a thermogravimetric analysis (TGA) technique with batch-boat roasting followed by leaching. Ferrous and manganeus oxides could be chlorinated readily, but, in the absence of a reductant, the higher oxides of both iron and manganese were difficult to chlorinate. Thermogravimetric analysis curves were drawn to illustrate the complexitites of the reactions, and the possible mechanisms were discussed. Then three manganiferous materials from the Cuyuna Range of Minnesota were treated by a process involving the selective chlorination of manganese followed by leaching. The results were interpreted in the light of the chlorination mechanisms observed on the pure iron and manganese oxides.

Jan 1, 1969

By T. P. Dolley

Domestic production of industrial sand and gravel in 2004 was about 29 Mt (32 million st), a 6-percent increase from 2003. This increase was buoyed by a robust construction sector of the U.S. economy. U.S. apparent consumption was 30.3 Mt (33.3 million st) in 2004, an in-crease from 2003. Imports were about 490 kt (540,000 st) in 2004, an 11-percent increase from 2003. Imports of silica are generally of two types. They include small-quantity shipments of very-high-purity silica or a few large shipments of lower grade silica that were shipped only under special circumstances (such as very low freight rates).

Jan 1, 2005

By D. Gu, B. Lin

Discussion of concept Breakage of rock by machine is one of the major methods of excavation. With the development of modern engineering techniques, the advantages of using this method have become even greater. Improving efficiency and reducing the cost of rock breakage is the main goal of mechanizing the rock-breaking operation. For a given stratum, the efficiency of a machine excavation depends, to a large extent, on the design and method of application of the tools used. In a planetary cutter head, the subcutter heads move like planets around the main drive shaft. The general structure of the cutter head is shown in Fig. 1. As shown in this illustration, the main drive shaft (1-1) is connected to the tie bar (1) and, thereby, to a gear (5) that meshes with a fixed-gear ring (2). The subcutter head (4) is rigidly connected to the gear (5) by the subcutter-head axis (2-2). When the main drive shaft (1-1) rotates, the subcutter head (4) rotates around the axis (2-2), under the action of the tie bar and with the help of sleeve pipe (3). At the same time, axis (2-2) also rotates around the main shaft (1-1). As shown in Fig 1, [a] is the angle between the main shaft and the subcutter-head axis. This angle determines the shape of the drilling face. If [a] equals zero, the drilling face will be a flat surface (Fig.1 (a) ), and if [a] is greater than zero, the drilling face will be a spherical surface (Fig. I (b)). For a planetary cutter head, the most important design parameter is the transmission ratio (i), which is defined as [i = (0210)1(1)] Where [(a] is the angular speed of rotation of the subcutter heads around their individual axes, and [o] is the angular speed of rotation of the subcutter-head axes around the main shaft. In Eq. (1), i is positive if the direction of rotation of a subcutter head around its axes is the same as the direction of rotation of the subcutter-head axes around the main shaft (see Fig. 1(b)). Conversely, i is negative when the two directions are opposite (see Fig. 1(a)). When i is positive, the cutters on the subcutter heads form epicycloid paths on the drilling face, as shown in Fig. 2(a). Conversely, if i is negative, the paths will be hypocycloid, as shown in Fig. 2(b). It should be noted

Jan 1, 1996

By Ian Farmer, Nigel Glossop, Philip Garritty

Performance of tunnel boring machines - usually expressed in terms of penetration per revolution - is determined by relations between machine thrust and torque, head diameter and rock strength. It can be shown that for a given machine power and head diameter there is only one rock strength at which the machine performs optimally. In weaker rocks the available torque limits performance and in stronger rocks, the available thrust. Performance data shows that, historically, machines have been designed to cut weaker rocks. Optimization of thrust is required to improve performance in stronger rocks.

Jan 1, 1987

By Richard Crowell, James Gillaspie

A concentrate biooxidation process was successfully demon­strated in the field in a remote part of northwestern Mexico. A 275 tonne (300 st) biooxidation heap was constructed using GeoBiotics' proprietary GEOCOAT™ coated concentrate process. The pyrite/chalcopyrite/sphalerite concentrate was bioox­idized in the heap for 60 days. Cyanide leach recovery of the con­centrate increased from 68% gold recovery at a cyanide consump­tion of 1.6 kg NaCN/g Au (llO lbs/oz) in the as-received concen­trate, to 94% gold recovery at a cyanide consumption of 0.37 kg NaCN/g Au (27 lbs/oz) in the biooxidized concentrate. The heap was constructed at a rate of7 tonnes (7.5 st) concentrate per hour, using typical heap leach equipment and easily scalable methods. Heap operations demonstrated that energy dissipation in the humid summer environment was easily controlled by low pressure aeration and management of solution chemistry and application. Observations of the demonstration heap appear to support the presence of reflux of moisture within the biooxidation heap.

Jan 1, 1998

By P. Burmeister, R. A. Errath, A. Sapin

Sag Mills are becoming bigger in size almost every year. Concentrator plants are also becoming larger with more SAG and Ball Mills units with Gearless Mill drives installed in one plant. In contradiction to this development, concentrator plants are being built in increasingly remote areas, where the power supply and network conditions are not necessarily covering the needs for the operation of such plants. This paper describes sources of harmonic distortions and possible approaches to solve this problem. It also illustrates the permissible tolerances in terms of commutation of power electronics, based on already realized installations. Furthermore it explains how, and with which measures, harmonic currents created by non-linear loads with SAG and Ball Mill drives can be handled, and how harmonic standards can be fulfilled accordingly. Finally, this paper gives an overview about the technical impact of a strong versus weak network, and the economic relationship between them.

Jan 1, 2001

By Kimberley MacHardy, Ann Maest, Greg Lawson, James Kuipers

Although water quality predictions are often made in Environmental Impact Statements (EIS's) as part of the National Environmental Policy Act (NEPA), comparisons between predicted and actual water quality conditions are rarely reviewed. A comprehensive review of predicted and actual water quality conditions was conducted for a number of large U.S. hardrock mines with EIS’s. For mines with large differences between predicted and actual conditions, factors responsible for the deviations, such as characterization and modeling errors or engineering failures, were identified. Recommendations are made for how the NEPA process could be modified to better predict water quality at hardrock mine sites.

Jan 1, 2005

Start with your assessment of the minerals business —domestic mining as well as operational and consulting perspectives. As a third generation miner, I have been living the mining business for as long as I can remember. I have watched commodity prices produce boom and bust cycles in places like Price, Utah (coal), Douglas, Arizona (copper) and Eureka, Nevada (gold). It is unsettling to see how our industry has fluctuated, but it always seems to rebound if you can stick out the down cycles. However, our most recent dip in the cycle was, in my opinion, characteristically and permanently different. In the past, when prices went south, people hunkered down and waited out the cycle until things came back, much the same as they had every other time. Not this time. This time, we saw a consolidation of the industry in proportions never seen before. Mega-mergers like Exxon-Mobil, Phelps Dodge-Cyprus and Newmont-Normandy have changed the complexion of our industry forever. And that is true not just of the mining companies; it happened across the supporting business lines as well. As a midsized niche engineering and environmental service provider to the mining industry, companies like mine are few and far between these days. The lean cycle saw many of the small and midsized providers get gobbled up by consulting giants like URS and TetraTech. The mentality of a mega-company, whether a commodity producer or a goods or service provider, is different than that of their small- and medium-sized counterparts.

Jan 1, 2005

By E. F. Perry

Simulated weathering tests are used to estimate leachate quality of rocks containing varying concentrations of pyrite and carbonates at mines. This study reports the inter-laboratory results from the third phase of a three part effort to develop a standardized, reproducible simulated weathering test for coal mine overburden. Initial development in phases I and II included evaluation of different test apparatus, effects of particle size, gas composition, leaching frequency and other variables. Phases I and II results are reported by Brady et al (2004) and Hornberger et al (2004). In Phase III, a standard column leaching protocol was used by eight commercial, government and university labs to test five rocks of different lithology, pyrite and carbonate content. Ideally, a simulated weathering test should have three characteristics to be useful in mine drainage studies. These include the capability to produce repeatable results, accuracy in simulating field conditions, and a concise test protocol of weeks to a few months. Simulated weathering, or kinetic testing, produces an effluent that simulates mine drainage composition. This can be beneficial for predicting mine drainage quality in comparison to whole rock analyses. The effluent may be tested for the same water quality parameters as the drainage produced during mining, such as pH, acidity, alkalinity, sulfate, iron, manganese, aluminum or other parameters. If the physical, chemical, and biological conditions of the kinetic tests are representative of those found in the mine environment, leachate composition may be used to estimate the water quality parameter concentrations produced during mining. Hornberger and Brady (1998), and Geidel et al (2000), compiled comprehensive chapters on kinetic tests for mine drainage prediction. These sources included: (1) a chronology and synopsis of scientific literature on these kinetic tests as they have developed over approximately 50 years, (2) discussion of the influence of physical, chemical, and biological processes, and (3) general guidelines for test procedures, data interpretation, and recommendations for further research to develop standard methods. Most of the kinetic test methods in use today were substantially developed and applied more than 40 or 50 years ago, including leaching columns (Braley, 1949), humidity cells (Hanna and Brant, 1962), Soxhlet reactors (Pedro, 1961), and field scale tests (Glover and Kenyon, 1962). . The most commonly used kinetic tests for mine drainage prediction are leaching columns and humidity cells. While these kinetic test methods and others have been used in hundreds of mine drainage studies as shown in Hornberger and Brady (1998) and other references (e.g. Sorini, 1997), they have rarely been used in coal mine permitting by either regulatory agencies or the mining industry. The major impediment to routine use of kinetic test methods is the variation in the design and operation of these kinetic tests, and lack of a standardized, accepted (e.g. by EPA or ASTM) test method. Interpretation and data comparison from different studies can be difficult. METHODS Five rocks of varying lithology, mineralogy, carbonate and pyrite content were collected in bulk from Pennsylvanian age coal measures in Pennsylvania, West Virginia and Indiana. Mineralogical composition of the samples was characterized in detail by Hammerstrom et al (in press) using optical, X-ray diffraction, scanning electron microscopy and electron microprobe methods. Acid Base Accounting (Sobek et al 1978; Skousen et al, 1997, Kania, 1998) was performed on bulk samples for % total sulfur (%S) as a measure of pyrite and potential acid generation, and Neutralization Potential (NP) as an index of carbonate content. A modified NP test, following the procedure suggested by Skousen et al, 1997 was also conducted for four of the five samples. The modified NP test accounts for initial acid consumption, Fe oxidation, and subsequent Fe hydrolysis by the iron carbonate mineral siderite. Siderite, even though it is a carbonate gives zero net alkalinity. Lithologic, Acid Base Accounting and general mineral composition data for the five rocks are shown in table 1 (see Appendix). Whole rock elemental analysis for major and trace elements was conducted on a sub-sample of each rock type. One laboratory was contracted to mix, homogenize, and size the bulk samples and prepare sub-samples for all the participating labs. Splits were sent to eight labs, and each organization was provided a detailed set of instructions for column assembly and leaching procedure. The protocol was developed based on results from phases 1and 2 of this study. The principal features of the column assembly are: a specific composition of particle size by weight (table 2), weekly leaching cycles, and incubation under humidified air containing 10% CO2. Figure 1 shows the column construction. [ ] The particle size distribution of the crushed rock sample is largely an artifact of the crushing process, rather than a natural systems process like the particle size distribution of a soil or an unconsolidated sedimentary deposit. The standardized particle size distribution, shown in Table 2, promotes operational consistency of the weathering test procedure, and provides better control over reaction kinetics. Large amounts of fine particles within specific zones of the leaching columns have been found to impede uniform fluid flow and/or gas flow (Hornberger and Brady, 1998). Regarding reaction kinetics, the importance of surface area to volume ratios has been described in a previous phase of this study (Brady et al., 2004), and significant differences in crushed particle size distributions and effective surface areas were found among the lithologic units. Standardizing the particle

Jan 1, 2009

By F. S. Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors, lead to an understanding of the mechanisms causing roof problems. Factors such as unexpected rolls of the roof strata resulting in a gradual change from strong to weak roof; encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described. Strategies for overcoming these problems are discussed and detailed.

Jan 1, 2002

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009

Lime production is the largest single chemical use for limestone and dolomite. The term “lime” in this review refers to high-calcium and dolomitic quicklime, their hydroxide forms and dead-burned dolomite. This review is restricted to a discussion of the U.S. lime industry. Production and consumption In 2004, according to preliminary data, U.S. lime production was about 20.1 Mt (22.1 million st), an increase of 900 kt (990,000 st) compared with 2003. Production in2004 was valued at about $1.4 billion. Commercial sales of lime totaled 18.6 Mt (20.5 million st) and captive production was 1.5 Mt (1.65 million st). Total U.S. consumption was about 20.2 Mt (22.2 million st). The majority of U.S. lime trade was with Canada.

Jan 1, 2005

By P. Conrad

Experience has shown that, since the passage of the Surface Mining Control and Reclamation Act, over-compaction of spoil during the reclamation process has severely limited tree growth on reclaimed land. Researchers at the University of Kentucky have conducted a ten-year investigation at a surface mine in eastern Kentucky that monitored the changes in selected spoil physical characteristics for various reclamation and compaction alleviation methods. More specifically, research plots were developed for reforestation that employed three different levels of compaction and two different methods of ripping for overly compacted spoil. Each year measurements were made in the field of dry bulk density, using a nuclear density gage, and maximum penetration depth, using a recording cone penetrometer. In addition to good correlation between tree growth and selected spoil characteristics, the data demonstrated a gradual convergence of the measured spoil characteristic data over the study period.

Jan 1, 2008

By J. J. Gresham

Homestake’s first links with Australia were established in 1934 but it wasn’t until 1961 that the company established a formal presence in the country. After involvement and success in iron ore and nickel, Homestake made a strategic investment in the Kalgoorlie gold operations in 1975 and now owns 50% of Kalgoorlie Consolidated Gold Mines, operators of Australia’s biggest gold mine. In 1998 Homestake acquired the major Australian gold producer Plutonic Resources, is now firmly established as Australia’s second largest gold producer and is actively seeking further opportunities for growth in the Austral-Asia region. Homestake’s success in Australia has been the result of important strategic alliances, timely investments, a long term commitment to the region and perseverance during periods of depressed commodity prices.

Jan 1, 2001

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By R. L. Virta

Twenty-three companies mined kaolin in nine States in 2004. Production was estimated to be 7.6 Mt (8.3 million st) valued at $912 million, based on preliminary data. This was a slight decrease from 7.68 Mt (8.46 million st) valued at $939 million in 2003.Georgia was the leading producer state with an estimated 6.5 Mt (7.1 million st) in production. It was followed, in decreasing order of tonnage, by South Carolina, Alabama, California, Texas, Arkansas, Nevada, Florida and North Carolina. Georgia accounted for nearly the entire domestic water-washed, delaminated, and pigment-grade calcined kaolin production. Consumption Sales to the paper industry accounted for 49 percent of domestic sales and 64 percent of total sales. Other major markets for domestic sales were refractory products (10 percent), paint (5 percent), fiberglass (4 percent), catalysts (3 percent) and rubber (2 percent).Paper coating and filler markets accounted for about 87percent of export sales of kaolin.

Jan 1, 2005

By H. Sevim, M. K. Mohanty, Y. P. Chugh

The economics of “Conventional” and “Advanced Fine Coal Cleaning” (AFCC) circuits for refuse pond reclamation as well as active mine/preparation plant applications have been evaluated. The benefits of innovative tailings management schemes on the profitability of mining enterprises have also been evaluated as a part of this study. Analyses have been conducted for scenarios involving generation of two different product qualities of 5.81%, a quality that was obtained during AFCC circuit operation at SIU, and a more typical 8% product ash. The inability of the conventional circuits to achieve profitability while producing the lower ash content product is revealed from this approach. The spiral-only circuit is unable to produce a 5.81% ash product. A different version of the same circuit involving spirals and column flotation produced the desired product quality but could not maintain profitability. The AFCC circuits on the other hand, achieve net present values greater than $6 million, with return on investment in excess of 50%, in the water-only as well as dense medium mode, with and without tailings management. Addition of tailings management system to any of the circuits is found to enhance the project economics. The comparison of water-only and dense-medium applications of the AFCC circuits indicate a better suitability of the dense-medium circuit for producing premium quality products. Application of AFCC circuits in active mines offer better economics compared to applications in refuse pond recovery operations. The superior project economics are a result of reduced overhead cost and use of existing material handling facilities. Sensitivity analysis reveals the significance of capacity utilization on project economics.

Jan 1, 2002

By S. Kim Juniper

"This presentation aims to serve as a primer on conservation, research and regulatory organizations interested in the environmental impact of deep-sea mining. It will also consider a recent, early-stage proposal for an experimental SMS mining operation aimed at increasing our understanding of mining impacts and ecosystem recovery.Over the past 5 years, as deep-sea mining has been moving closer to reality, it has attracted growing attention from deep-sea biologists, conservation groups and operators of deep-sea research vehicles and observing systems. Several new international research organizations have emerged that have a direct interest in deep-sea biodiversity conservation, and the environmental impact of ocean mining. These include INDEEP, which evolved from the 10-year Census of Marine Life program, the Deep Ocean Stewardship Initiative that has recently hosted several high profile international meetings, and the VentBase forum of academics, industry and regulators that aims to develop environmental best practices and informational documents for all stakeholders involved in Seafloor Massive Sulphide (SMS) mining. InterRidge, currently hosted by China, represents a decades old partnership of deep-sea biologists and economic geologists who discovered the more than 100 known hydrothermal vent fields and SMS deposits on midocean ridges and in other settings of seafloor volcanism. In 2012 InterRidge formed an industry liaison group to examine how the mid-ocean ridge researcher community could contribute to the development of environmentally responsible practices for the exploration and exploitation of SMS deposits. While initial meetings with industry were promising, InterRidge members are currently debating the relative merits of sharing exploration know-how and understanding of vent ecosystems with industry, against the need to maintain their independence as stewards of deep-sea ecosystems."

Sep 1, 2014

Sandvik built its first stone crusher in 1896 and has since grown to become a world leader in mining equipment. ?We are the best in the world, and we can now be even better at making our cone and jaw crushers in different models,? Olle Lundberg, production engineer at the Sandvik Mining factory in Svedala, Sweden told freelance journalist U. Samuelsson, of mekpoint.com. As a specialty manufacturing business under the umbrella of the Sandvik Group, Sandvik Mining is a leading global supplier of equipment, tools, services and technical solutions for the mining industry. Its expertise covers the areas of rock drilling, cutting and crushing, as well as loading, hauling and the handling of materials. Lundberg, along with five colleagues, will write CNC programs for the lathes and machining centers that manufacture Sandvik?s specially constructed casting. In 1999, Sandvik chose ESPRIT computer-aided-manufacturing (CAM) software by DP Technology to program its array of machine tools, and has worked with ESPRIT reseller Holotech, based in Örebro, since 2003.

Jan 1, 2014