Search Documents

By Erik Klohn

The El Soldado copper deposit occurs in volcanic rocks of alkaline affinity of Lower Cretaceous age. The orebodies are discordant and show strong structural and lithological control. The mineralizing event was accompanied by hydro- thermal alteration expressed as carbonatization, silicification, and chloritization. Individual orebodies contain bornite-chalcopyrite cores which are surrounded by haloes dominated by chalcopyrite and pyrite respectively. The sulfur isotope composition of copper sulfides strongly suggests the sulfur is of magmatic origin. Fluid inclusion studies show the mineralizing fluid to be a highly saline NaC1-CaC12, brine. No evidence of boiling was found. The deposit is most likely of epigenetic origin. Hydrothermal fluids were produced during crystallization of a sodium rich trachytic magma during the waning stages of an episode of alkaline magmatic activity. Similar copper deposits along the Chilean Coastal Range may also be associated with alkaline host rocks.

Jan 1, 1986

By Z. H. Xie, D. S. He, W. M. Xie

China has rich phosphate rock resources, but with their continuous depletion, the rich ore resources have become increasingly scarce, which makes the exploration of collophane more important. Medium- and low-grade phosphate rock cannot be utilized until their impurities have been removed through mineral processing. However, due to the similar physical and chemical properties of dolomite and phosphorus minerals, the separation of dolomite from phosphate

By Rongdong Deng

A tower-like magnetic system comprising eight permanent magnets was installed at the center of a flotation column to separate chalcopyrite and pyrrhotite minerals. A cyclonic flotation was installed within the underpart of the column to separate the pyrrhotite from the gangues. A three-product magnetic flotation column was fabricated to create a magnetic field and a cyclonic zone. The products were Cu concentrates, pyrrhotite concentrates and tailings. The theoretical magnetic field strengths and the magnetic forces were calculated. The results of the flotation experiments showed that the Cu grade increased from 14.20% without the magnetic field to 26.40% in the presence of the magnetic field and that the S grade in the pyrrhotite concentrates increased in the presence of cyclonic flotation. The separation efficiency of this magnetic flotation column was evident. Therefore, this three-product magnetic flotation column may have a potential application, due to its high separation efficiency.

By Donald P. Richards

Is a shaft the same as a tunnel and can it be approached in the same manner for design and construction? The most obvious difference between a shaft and a tunnel is that of orientation; whereas a tunnel is commonly near horizontal or slightly dipping, a shaft is commonly vertical or steeply inclined. As a result, design and construction methods employed for tunneling, in general, cannot be directly applied to shafts, although some of the basic concepts of behavior are quite similar. Many of the shafts that have been sunk in various parts of the world are owned by private mining companies. Each company has generally accumulated years of experience in shaft sinking and mining techniques pertinent to its particular geographic location. When a new shaft is to be sunk or an existing shaft deepened, the tendency often seems to be to continue to use the methods that have been used successfully in the past.

Jan 1, 1979

By Ari Glazer

"Every year the tunneling business is expanding and collaboration with the International Society of City and Regional Planners (ISOCARP) for the future design of cities and urban communities is in the making. During the last half of this century, billions of people migrated to cities, and it is estimated that by 2030 almost five billion people worldwide will reside in urban communities. Hence, “Underground development will be an important tool in reshaping our urban areas to meet the challenges of the future without destroying their heritage or worsening their surface environment” (Esaki, 2005). In 2013, the Organization for Economic Co-operation and Development (OECD) estimated life expectancy to be around 80 years, meaning that in less than a decade we will need to bury billions of people in cities and urban communities, while trying to retain the deceased’s beliefs and customs. Religion plays a major role in our lives, and many people worldwide still decline to cremate their body after their death; therefore, cemeteries are essential for city inhabitants. Rites and traditions usually call for burials to be near the place of residence, which allows the remaining family members and friends to visit the grave frequently, at least in the first years. This is a challenge that urban designers and architects must confront while trying to solve the problems of future urbanization. In recent years, population growth, the rising cost of land and the extensive preservation of green areas have made cemeteries a burden and a nuisance, particularly for large cities and communities. Many graveyards that were once on the city's outskirts have become lifeless islands in populated areas (Fig. 1), rarely visited by the second and later generations. Cities worldwide face the challenge of allocating less land to maintain current burial practices. In response, some cities have begun to bury their dead at a great distance from the community; others have started to stacked burials, one on top of the other, while still others are constructing buildings and even skyscrapers for the practice of burial (Fig. 2)."

Jan 1, 2016

By R. Q. Honaker

Although the fundamental principles of hindered bed classifiers are relatively simple, the complex interactions between the operating parameters provide a degree of difficulty that hinders the ability for on-line plant optimization. Thus, a dynamic population balance model was developed for determining the hindered settling velocity of particles varying in density and size. The steady-state results of the model include partition curves as a function of particle size and density as well as metallurgical data. A statistical comparison of the simulation results with those obtained from industrial units reveal a high level of accuracy with adjusted R2 values greater than 0.95.

Jan 1, 1999

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72×10−2 m3/ s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97×10−3 m3/ s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16×10−1 m3/ s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07×10−2 m3/ s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 15, 2023

By Gordon Kidd

Inflation and burgeoning costs are two among many factors which have generated a new surge of interest in "fringe benefits" (sometimes referred to as "supplementary remuneration" or "supplementary compensation"). Other specialized forms of compensation ("perks", in the vernacular) such as company cars, windowed offices, etc., which also are the subjects of current study, are outside the scope of this paper. For businesses, interest in fringe benefits is based on concern for employees? welfare, compliance with government requirements, and an increasingly burdensome impact on bottom lines. In 1980, according to Fred D. Lindsey in the October 1980 issue of Nation's Business, employee benefits will cost American employers an estimated $420 billion. To paraphrase Winston Churchill, "some fringes!" Indeed, few if any administrators consider employee benefits as fringes. Employee benefits impact other major areas of a company's operations as well. As listed by Beadle (1980), these areas include employee relations, collective bargaining, short-term costs, long-range funding, manpower planning, compliance with legislation, taxation for the company and for the employee, corporate image in the community, competitiveness for staff, communications, administration, claims cost containment, etc., etc.

Jan 1, 1980

By Vic Miller

Highly variable milling properties within a geologically complex porphyry copper deposit owned by Kennecott Corporation in Nevada made it necessary to estimate the copper recovery and concentrate grade in areas where actual test data was lacking. The estimation was made by first determining the relationships between the desired metallurgical properties and the ore's petrology (i.e. copper mineral type, rock type and copper grade). This relationship was then combined with the already estimated rock type, mineral type and copper grade data in the mineral block model to predict the milling properties.

Jan 1, 1983

By Trenton Cohen, Joseph McDivitt, Shimi Tzobery, Joseph Sinacori, Scott Zylstra

The 2-mile Beach Interceptor Sewer Tunnel was constructed in 1954 to then-current mining and construction standards. Due to its lifespan and deteriorating condition it is now being stabilized and rehabilitated using conventional excavation and ground support. At its southern end, below the prestigious Three Arch Bay community, the original tunnel alignment passes under a historic landslide where the tunnel was sand-backfilled and capped by bulkheads in 1957 due to severe and caving ground conditions. Video footage of the existing 21- inch clay pipe showed that the pipe is severely damaged, which could potentially cause a catastrophic pipeline failure and sewage spill into the Pacific Ocean. This paper summarizes the thorough investigation and design process, tunnel realignment construction and monitoring, and the notable cooperation between all parties to overcome the project risks.

Dec 1, 2022

By Jonathan G. Price

The 2011 report titled ?Energy Critical Elements: Securing Materials for Emerging Technologies? by the American Physical Society?s Panel on Public Affairs and the Materials Research Society surveys potential constraints on the availability of these elements and identifies five specific areas of potential action by the United States to ensure their availability: 1) federal agency coordination; 2) information collection, analysis and dissemination; 3) research, development and workforce enhancement; 4) efficient use of materials and 5) market interventions. Energy-critical elements (ECEs) are a class of chemical elements that currently are critical to one or more new energy-related technologies. A shortage of these elements would significantly inhibit large-scale deployment, which could otherwise be capable of transforming the way in which energy is produced, transmitted, stored or conserved. The report addresses elements that have not been widely extracted, traded or used in the past, and therefore are not the focus of well-established and relatively stable markets (such as carbon in coal or uranium as fuels, copper, aluminum, nickel and iron, all of which are clearly vital in energy applications).

Jan 1, 2011

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By James H. Vignos

An optical instrument designed for the on-line measurement of the size distribution of coarse particles (3-500 mm) being transported on a conveyor belt is described. Included is a discussion of the measurement technique, as well as test data verifying the legitimacy of the basic sensing approach. Field data indicating the instrument's ability to make useful measurements in an industrial environment are also presented. Applications in the mining and mineral industry, for which this instrument was orginally developed, are outlined, with particular emphasis given to the areas of crushing and grinding control.

Jan 1, 1979

By C. V. Baltzer, E. L. J. Bingham

Compliance with the EPA's emerging Clean Water Act regulations can be challenging. Open pit copper mines in Arizona have found themselves in a tangled web of changing rules, regulations, and guidance documents regarding storm water and process water discharges. Large mining properties must come up to speed on a myriad of issues including the definition of zero discharge, what constitutes a process related spring or seep, and tailings and waste rock Best Management Practices. The example of the Pinto Valley Mine in Arizona is used to illustrate National Pollution Discharge Elimination System regulatory issues.

Jan 1, 2001

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

By Y. Luo

"It is generally known that spontaneous combustion potential is a function of coal rank, with low-rank coals having high susceptibility to self-ignition and high-rank coals having low potential. To establish this functional relationship and use it as an engineering tool to identify the propensity of coal to self-heat, both rank and spontaneous combustion potential should be quantified. ASTM D388 is normally used to classify coals by rank, but this classification system can only serve a qualitative analysis. To classify coals by their potential for spontaneous combustion, the self-heating temperature (SHT) method originally developed by the U.S. Bureau of Mines (USBM) was used by Litton and Page (1994) to correlate coal rank with spontaneous combustion potential. In that method, the SHTs of coal determined by an adiabatic experiment are linked with proximate analysis results through a proposed concept known as the “moist fuel ratio.” This ratio is a function of moisture, volatile matter and fixed carbon, all of which have widely different content percentages in different ranks of coal and have strong relationships with coal rank. However, the method is highly empirical, and there is large standard deviation between experimental data and calculated results. The equation correlating the coal quality parameters to determine SHT should be improved with more experimental data.This paper reports on the development of a new system for predicting the spontaneous combustion potential of U.S. coals, based on coal composition data from the U.S. Geological Survey’s coal quality database. First, the user is provided with a quantified classification of coal rank. Second, based on experimental SHT data covering a wide range of ranks from lignite to low-volatile bituminous coal, the original USBM correlation for predicting SHT is improved for the respective rank of coal. The relationship between the rank and SHT of U.S. coals was developed and plotted. The plot diagram can be used for a quick estimate of the SHT of a U.S. coal and as a cost-effective tool for the initial risk assessment of a new mine development."

Jan 1, 2015

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Khaled Mohamed

Resin-grouted bolts serve as a crucial means of stabilizing yielded coal ribs in underground coal mines. A comprehensive investigation into their efficacy was undertaken by a collaborative effort between the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST). This study involved pull-out tests in multiple locations, including six coal mines and the NIOSH research mine. A total of seventy-three (73) tests were conducted, of wide range of anchorage lengths, ranging from a short encapsulation length of 0.305 m to a fully grouted encapsulation length of 1.524 m. The test findings indicate that when short encapsulation bolts are installed at high rotation speeds, their anchorage capacity is significantly reduced, leading to failure at the bolt-grout interface. Conversely, when these bolts are installed at lower rotation speeds, they exhibit greater capacity, with failure occurring at a higher anchorage load equivalent to the yield load of steel rebar. No matter what the rotational speeds were used during bolt installation in this study, the fully grouted bolts consistently experienced failure at the ultimate load of the steel rebar. Most of the tests carried out on partially grouted bolts with anchorage lengths of 0.610 - 0.914 m have shown behavior patterns like the fully grouted bolts, although exhibiting reduced stiffness. The outcomes of this research offer a profound insight into the ways in which resin-grouted bolts enhance the stability of coal mine ribs.

Feb 1, 2024

By W. W. Edgerton

Construction projects may be delivered under one contract package or multiple packages divided by discipline, geographic location, or other characteristics. Dividing the construction into contract bid packages is called contract packaging, and is a vital and strategic aspect of effectively delivering tunneling projects. The process of contract packaging considers many factors, including the type of project, location, and owner?s priorities. This paper describes the key facets of the contract packaging process used recently on several tunnel projects, reports, where possible, on the success of the process, and concludes with recommendations for applying this process to achieve the right contract package.

Jan 1, 2008

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010