Search Documents

By John W. Graham

To start my talk, I thought it might be helpful for us to define the term "aggregate", so I went to the dictionary. Webster has several listings under "aggregate", and I found the following: "1. A mass or body of units or parts somewhat loosely associated with one another." Well, I didn't like that term "loosely" so I read on. "2. Crystals of one or more kinds of mineral or rock fragments." That sounded better, but I still read on. "3. Any of several hard inert materials used for mixing with a cementing material to form concrete or mortar." That sounded even better, but it should be a little broader. So I would like to define "aggregates" for you as follows: "Hard, inert fragments of rock or minerals used alone or with cementing agents to form products essential to nearly all types of construction." Usually aggregates are sand, gravel, or crushed stone, but other minerals such as clay or shale can be heated and become aggregates. What are some of the construction uses? Well, we've already mentioned concrete, as used in streets and highways, sidewalks and parking lots, airports and all kinds of building construction, not to mention bridges and swimming pools, and docks and breakwaters, just to list some of the uses. Our way of life couldn't exist without concrete. And you can't have concrete without aggregates,

Jan 1, 1977

By T. Hackett

Western underground coal reserves are tremendous, but recovery in western seams can be poor because of mining problems caused by deep cover, geologic anomalies, and thick seams. For instance, many seams contain a rock parting too thick to be extracted economically with the coal. This forces the operator to mine the coal above or below the parting. Subsequently, the rock pressures induced by mining make the part left difficult or impossible to extract by standard mining methods. Because upper and lower parts of the seam are frequently of minable thickness, the presence of rock partings can result in a significant loss of coal. Given a longwall recovery of 60 pct and equal thickness for the two parts of the seam, overall recovery is reduced to less than 30 pct if one part only is mined. The coal left in place is unavailable to meet the nation's energy needs, or to produce revenues for coal companies or government. [ ] Multi-slice longwall mining has the potential to recover the portion of split seams that are now left in the mine. Using superimposed standard longwalls with chain pillars, overall recovery could be doubled, depending on panel and pillar widths. Using a combination of advancing and retreating longwalls in descending slices, overall recovery could be improved to more than 80 pct. Because of the potential for improved recovery, the Bureau of Mines is analyzing the ground control factors affecting multi-slice longwall under western mining conditions and is conducting field trials at a planned multi-slice operation.

Jan 1, 1987

By Robert E. Lovett

The truly educated man is better prepared to meet the challenge of the times. This challenge can be either beneficial or harmful depending upon one s orientation, Certainly man can no longer continue in the way of his father or even in the manner of his own previous experience as he seeks self-fulfillment, unless he is willing to sacrifice inner integrity--unless he is willing to compromise self-determination and self-expression. He must make a choice as society moves rapidly into high gear in the areas of automation and cybernetics. Industry, a unit of society, has a high stake in meeting this challenge, The better prepared and more mature its personnel, the better the end result as it attempts to meet the challenge. It therefore has a vital concern in proper training of such personnel, that their contribution will be of maximum quality. The specialized training required demands a broad liberal arts background which gives the individual a wider perspective upon which to base judgment. This greatly aids his development as he enters graduate school or goes directly into industry. In either case, his value to industry is enhanced. It would seem that the small liberal arts college provides the best environment for such a program, Consideration of several factors will, I hope, throw some light on the severity of the problem.

Jan 1, 1966

By F. P. Schwarz

Even in an otherwise care-fully done sampling procedure, reducing subsample weight, or splitting, when the grain size of material is too large commonly generates significant error. Such error can be estimated from the standard deviation of differences between values of PAIRED ASSAYS. Samples from split-ting steps immediately before comminution, and showing a restricted range of grade, generate paired assays. Splitting steps characterized by relative standard deviations exceeding 16% generate nonrepresentative data. Such steps should be redesigned to optimize reliability of assay-dependent studies. A sampling scheme can be graphically characterized, and then redesigned as appropriate, using a SAMPLING NOMOGRAPH. Use of the nomograph avoids continued replication of assays. Generally at a splitting step, excessive error can be reduced by comminuting more material. Unnecessary effort can be mitigated by comminuting less finely and/or by splitting to a smaller weight.

Jan 1, 1992

By Clark Woodland, William E. Stanley

Mining companies have been required to enter a "new era of management" in the 1980's as they strive to become more efficient in an increasingly competitive market place. One response for many companies has been to modify their mine accounting systems to make them more effective for cost control and decision-making. This paper discusses some of the major issues in developing and implementing a standard costing system as part of improved management reporting and cost control procedures. It describes the key features and benefits of a computerized standard costing system with particular emphasis on budget-setting and variance analysis. It also identifies important factors to be considered in order to achieve successful project planning and Implementation.

Jan 1, 1987

By M. R. Rosen

A technique is presented for simple characterization of the performance of flocculents in various mining applications. The method utilizes three key parameters obtained from raw settling data and combines them into a single athematical parameter called the desirability coefficient. The first two parameters are the timesrequired for the slurry-supernatant interface -to fall to two selected fractions of the starting height, and the third is the clarity of the supernatant liquid. The relative values of the three parameters may be assigned different weights in order to make them correspond with laboratory and field performance requirements of a particular industry. Provision is also made of an, internal comparison of test flocculant data with that of a control.

Jan 1, 1980

By Donald R. Simon

Money... not many subjects are as personal or as emotional. Hessiod said it well in 700 B.C. "Money is life to us wretched mortals". Are you getting paid enough? Does your company reward its top people? Does coal or copper pay more? Production or engineering? How is the synfuels industry going to influence mining salaries? Do high salaries attract and retain the best people? Do modern compensation systems ensure fairness or destroy entrepreneurial spirit? With our tax system and high standard of living why are we so salary conscious? Salary is not only important for what it can purchase but it is also a yardstick, measuring how well we are doing. We all need money to pay the bills and maintain our standard-of-living, but once we reach a certain point the psychological ramifications become more important than the purely practical side. Even necessary payments like the mortgage and the car are a function of our egos. Are our choices of cars and homes based on simple transportation and shelter?

Jan 1, 1980

By Paul C. Jones

Summitville is an old mining district located south of Wolf Creek Pass in the southern San Juan Mountains of Colorado at an elevation higher than 3500 m (11,500 ft). The Summitville mine site is about 40 km (25 miles) southwest of Del Norte. The current mine, developed by Galactic Resources Ltd. and its subsidiaries in the mid-1980s, is on the north facing side of South Mountain. The area is drained by Cropsy Creek to the east and Wightman Fork to the north, both tributaries to the Alamosa River. Mining in the Summitville area began in 1870 when James Wightman discovered placer gold on what is now known as Wightman Fork of the Alamosa River. The first vein-type deposits were located in 1873 on South Mountain near the current Summitville Mine. Mining began in the district in 1875 and continued sporadically through 1942. Major mining episodes occurred from 1875 to 1894 and from 1926 to 1942. Total gold production from the mining district through 1949 totaled 7.5 t (240,000 oz). An additional 7.7 t (249,000 oz) were produced during Galactic's tenure. Natural degradation of the outcropping sulfide-rich veins in the area and the early mining activity, including development of the Reynolds, Dexter and Iowa drainage tunnels in the late 1890s, have polluted the streams draining the area with heavy metals and acidic water. Names of the various tributaries to Wightman Fork, such as Iron, Alum and Bitter Creek, testify to this natural pollution. This degradation has reduced, or killed, aquatic life in several area creeks, including Wightman Fork, for many years before recent mining activity.

Jan 1, 1993

By Mike Rhodes, Paul Miller, John W. Neale, Vishal Deeplaul, Barrie Hancock, Tony Pinches

The Beaconsfield underground gold mine is one of only a few new Australian gold projects to come into operation in the current climate of low gold prices. Up to 200,000 tonnes per annum of Tasmania Reef ore will be mined and processed over a minimum eight-year life to a depth of 900 metres below surface. The Tasmania Reef is a gold-bearing quartz-carbonate-sulphide vein occupying an old fault structure which transgresses a series of sedimentary beds. The sulphides are predominantly pyrite with lesser arsenopyrite, and also minor copper as chalcopyrite. Drilling to date below this level clearly indicates that the high-grade orebody is open at depth and that the mine life should be extended significantly over time. Since redevelopment of Beaconsfield mine began in the 1980's, extensive exploration has identified a resource of 1.5 million tonnes within a 450 vertical metre zone beneath the old workings, which extended more than 450 metres below the surface. Installation of an 800 litre per second capacity pump station 180 metres below the surface has been critical in overcoming one of the major hurdles experienced during previous operations in the early 1900's. A multi-stage development program, designed to bring the mine into full production, and incorporating construction of the on-site gold treatment plant incorporating bacterial oxidation, has now been completed. Prior to execution of a detailed engineering design of the Mintek-BacTech bacterial oxidation process, a programme of bacterial oxidation testwork was completed to provide a basis for fixing the process design criteria. A flow diagram of the Beaconsfield treatment plant is shown in Figure l. It comprises:

Jan 1, 2000

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor --will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Jan 1, 1997

By B. Moudgil, Hassen El-Shall

Particle shape and size distributions are among the most important parameters that affect the filtration efficiency of phosphogypsum in wet- process phosphoric acid production. Cost-effective enhancement in filtration rate is desired by phosphoric acid producers for higher plant capacity and lower operating costs. In this regard, numerous research efforts have been carried out in different laboratories as well as in pilot and plant testing. Nevertheless, changes in phosphogypsum crystal shape and size distribution deserve special attention. In this study, the results obtained in the presence of Crysmod and Hiflo-S5 surfactants are discussed. The influence of such additives on crystal morphology and size distribution are studied under different sulfate contents (supersaturation). The obtained data are correlated with process efficiency parameters such as filtration rate, digestion of rock, and recovery of phosphate values. Up to 60% increase in filtration rate is obtained. In addition, an increase in digestion efficiency and P205 recovery is achieved due to addition of surface active agents. The observed beneficial effects are explained in the light of the changes induced in crystal habit, size, and size distribution.

Jan 1, 1999

By L. Donovan Clark

The term "powder factor" is almost universally accepted as the measure of the efficiency of a blasting program. It represents the economics of blasting since it designates quantity of explosive (thereby providing quality control in rock fragmentation) in terms of the associated volume broken. It is the wide use of this concept that explains the interest shown in an approach to rock blasting preferred by A. W. and Z. W. Daw* in a treatise on 3 blasting (1) substantiating its use in the form, Q = CVW3 for single shot hole, where Q = quantity of explosive lb Cv = blasting coefficient W3 = unit volume of rock It is obvious that the term Cv could also be called the apparent powder factor should the equation be written in the form, Cv = Q/W3 (lb per cubic unit). However, while the approach was ingenious** and the practical applications straightforward, their original, rather limited experimental work, along with certain assumptions, was questioned.

Jan 1, 1970

By Sterling S. Cook

The U.S. Bureau of Mines is conducting core leaching experiments with sulfuric acid on oxide copper ores from the Cyprus Casa Grande and ASARCO Santa Cruz deposits in Arizona to further our understanding of the leaching process in supergene copper ores as it relates to in situ mining. Leach solutions from atacamite mineralization contained 5 to 30 g/l copper and few extraneous ions. Leachant from chrysocolla ores, with grades similar to the atacamite, contained 2 to 9 g/l copper and abundant extraneous ions. Quartz and K-feldspar had no impact on leach solution composition at any acid concentration (up to 40 g/l) while illite and sericite had minimal impact. Biotite, calcium-rich clay and limonite have a significant impact on solution chemistry when there is abundant free acid in solution. High acid concentrations increase acid consumption in ores with abundant biotite and limonite gangue. High acid concentrations can be used in ores with quartz, K-feldspar, and sericite gangues without increasing acid consumption per unit of copper removed.

Jan 1, 1988

By W. Jack Wilkes, Gilbert L. Butler

TRANSPORTATION TUNNELING The use of tunnels for transportation, namely rapid rail transit systems and highways is on the increase. How much that increase might be through the 1980's is the question that is discussed in this paper. In 1975, there were 218 route miles of subway tunnels for rapid rail transit and 154 lane-miles of highway tunnel. From the viewpoint of many transportation planners and designers, the tunnel is one of the tools which may be used to by-pass many types of obstacles: a mountain, a body of water, or a Central Business District (CBD). Therefore, the transportation tunnel is a rural as well as an urban solution with major emphasis on the latter because of the current transportation needs of our cities. In the case of rural locations, tunnels are usually constructed through mountains in order to eliminate miles of steep grades and dangerous curves, such as the Eisenhower Tunnel which cuts through the Continental Divide in Colorado along 1-70 and saves 10 miles and 40 minutes of driving time. Tunnels also provide an excellent transportation link across bodies of water in order not to interfere with shipping lanes. The Chesapeake Bay Tunnel and Bay Tubes of the BART system are excellent examples of this type of tunnel.

Jan 1, 1976

By Don Macfarlane, Brian Heer, Tom Martin

The Manapouri Power Station, commisioned in 1969, is located in Fiordland National Park in the South Island of New Zealand. It is the country’s largest hydro power scheme and can generate 700MW of electricity. The power station utilizes the hydraulic head of Lake Manapouri, using an underground power station and a 10 km-long tailrace tunnel was constructed by drill-and-blast to allow discharge to Doubtful Sound. Power generation fell short of expectations due to higher than expected friction in the tailrace system. To remedy this a second tailrace tunnel was constructed between June 1998and May 2002. It consisted of a 10 m diameter, 10 km long tunnel in predominately gneissic rock and was excavated using an Atlas Copco Robbins TBM. High water inflows, Owner/Contractor production incentives and a major claim settlement were handled during the 5 1/4 year project. This paper discusses TBM advance rates, utilization factors that increased in the second half of the project plus an innovative method for sealing Tunnel 1 to construct the bifurcation.

Jan 1, 2003

By S. Rupprecht

"INTRODUCTION This paper addresses the prevalence of poor public reporting practices of Coal Exploration Results, Coal Resources and Coal Reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or “saleable” tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal – therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (“ROM”) and Saleable coal tonnage, their associated qualities and other material and relevant information. Competent or Qualified Persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provide. “Companies are encouraged to provide information in their Public Reports, which is as comprehensive as possible” (CRIRSCO, 2013): too often this isn’t the case and material matters are either not reported or inadequately disclosed. According to the South African National Standard (SANS) 10320:2014 draft document - “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw Saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the Saleable Coal Reserve must be stated. The moisture basis of reporting shall be stated.” As an example to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are highlighted. The Kendal power station, commissioned in 1988, operates at a Calorific Value (“CV”) range of 19 to 20MJ/kg, an Ash content between 29 and 34% and Volatiles between 20 to 21%. Other power stations, such as Kriel or Hendrina, may require different qualities such as a CV range of 22 to 23MJ/kg, an Ash content between 20 and 28% and Volatiles between 22 to 23%. Thus, in terms of domestic saleable coal, it isn’t just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station” (Chetty, 2010). Sulphur content is also another important quality with the ideal coal content having a quality of less than 1% Sulphur."

Jan 1, 2018

By J. M. Goris

The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co., and the University of Utah, is conducting a field demonstration to evaluate the behavior of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-4BN stope. 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behavior of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modeled using the finite-element code UTAH III. Field data will be used to verify the modeling. In addition. a comparison between the effectiveness of conventional and birdcage cables will be made.

Jan 1, 1991

By Michael J. Hannan, Thomas F. Torries

The nature of industry structure is examined and the structure of the aluminum, copper, lead and zinc industries are described by the use of factor analysis. Capacity is defined and the relationship between industry structure and capacity utilization is examined. It is demonstrated that excess capacity is possible in industries with competitive or monopolistic characteristics, but the effects of the overcapacity are vastly different in the two cases. In a competitive industry, cycles of overcapacity with attendant fluctuating prices are expected. A change in industry structure from monopolistic to competitive characteristics over time causes profits and economic rents to be transferred from the producer to consumers of the mineral.

Jan 1, 1989

By Alan G. Mayton, Jon C. Volkwein

The U.S. Department of the Interior, Bureau of Mines, in cooperation with an American firm, has been contributing toward the creation of a new highwall mining system for extracting coal in active, unreclaimed contour strip mines in the United States. The prototype system features the computer-based, remote control, video operation of a thin-seam continuous miner. Haulage is accomplished remotely also with a 76-m (250-ft) long multiple-unit continuous haulage (MUCH) conveyor system on rubber-tire vehicles. One aspect of this multi-faceted effort has been to design a ventilation system for removing dust generated at the face during the extraction process. The remote mining system eliminates the need for personnel in the mined workings. Ventilation is required to remove visible dust from the area inby two video cameras. These cameras are located approximately 6 m (20 ft) from the face, one on either side of a modified Jeffrey 102HP continuous miner. Removing the dust from this area provides the remote operator with constant visual monitoring of coal extraction at the face and thus, insures the effective operation of the mining system. A ventilation system was designed for use in a mine opening with a maximum cross-sectional area of roughly 4 sq m (44 sq ft) excluding the mining machinery. This paper describes the ventilation system and discusses how it was developed in view of the constraints imposed by the mining equipment, mining conditions, and the extraction process.

Jan 1, 1989

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018