Search Documents

By Z. Jin, D. DePaoli, P. Zhang

"Phosphate beneficiation in Florida generates more than one tonne of phosphatic clay, or slime, per tonne of phosphate rock produced. Since the start of the practice of large-scale washing and desliming for phosphate beneficiation, more than 2 Gt of slime has accumulated, containing approximately 600 Mt of phosphate rock, 600 kt of rare earth elements (REEs) and 80 million kilograms of uranium. The recovery of these valuable elements from the phosphatic clay is one of the most challenging endeavors in mineral processing, because the clay is extremely dilute, with an average solids concentration of 3 percent, and fine in size, with more than 50 percent having particle size smaller than 2 µm, and it contains nearly 50 percent clay minerals as well as large amounts of magnesium, iron and aluminum. With industry support and under funding from the Critical Materials Institute, the Florida Industrial and Phosphate Research Institute in conjunction with the Oak Ridge National Laboratory undertook the task to recover phosphorus, rare earths and uranium from Florida phosphatic clay. This paper presents the results from the preliminary testing of two approaches. The first approach involves three-stage cycloning using cyclones with diameters of 12.4 cm (5 in.), 5.08 cm (2 in.) and 2.54 cm (1 in.), respectively, to remove clay minerals followed by flotation and leaching. The second approach is a two-step leaching process. In the first step, selective leaching was conducted to remove magnesium, thus allowing the production of phosphoric acid suitable for the manufacture of diammonium phosphate (DAP) in the second leaching step. The results showed that multistage cycloning with small cyclones is necessary to remove clay minerals. Selective leaching at about pH 3.2 using sulfuric acid was found to be effective for removing more than 80 percent of magnesium from the feed with minimal loss of phosphorus.IntroductionFlorida phosphate ore, or “matrix,” as it is called locally, contains three different mineral groups that have to be separated from each other: (1) phosphate minerals, (2) clay minerals and (3) quartz, or sand. As mined, the phosphate and sand particles are embedded in compacted mud, or clay-balls. Before separation can begin, all of the particles must be liberated from the matrix of mud. The very first unit operation in the beneficiation process is to disaggregate the various particles. This actually starts while the matrix is flowing through the multimile pipeline from the mine to the beneficiation plant. While in the pipeline, the matrix is exposed to shear forces as it passes through the various centrifugal pumps along the pipeline. These intense shear forces cause a significant percentage of the sand and phosphate particles to be liberated from the clay-balls by the time they arrive at the plant. Once they reach the plant, the first goal is to finish disaggregating the clay, and follow that by making a size separation at 1 mm. This processing is conducted in the washer, consisting of a large rotating trammel screen and a few stages of log washer, screens and hydrocyclones. In all of the currently operating beneficiation plants, the washer is a large structure that receives the matrix, screens it and then discharges a pebble phosphate product sized larger than 1.0 mm and a slurry of liberated clay, sand and phosphate particles that are smaller than 1.0 mm."

Jan 1, 2017

By I. Shah, L. G. Austin

A method for quantitative investigation of the phenomena involved in fine grinding of materials that follows the changes in the breakage rates of fine particles has been presented. For relatively hard, brittle, non-coating material like quartz, the slowing down effect of breakage rates starts to be significant at relatively coarse sizes, which goes often undetected in closed circuit grinding systems, producing relatively coarse product, say P80=75µm However, for fine grinding systems, as the -10µm fractions begin to build-up, and classification becomes more difficult, the build-up of fine sizes causes a slowing down effect Compounding this problem is the difficulty of obtaining accurate cumulative weight size distributions in the fine size region.

Jan 1, 1983

By K. Mohamed, G. Rashed

A conventional mechanical anchor bolt consists of a smooth bar threaded at the anchor end, with a conical wedge, and a mechanical shell anchor. When the smooth bar is torqued, the conical wedge pushes the shell anchor against the borehole wall. Coal mines use mechanical bolts in addition to other types of bolts to control the deformation and stabilize the yielded coal ribs. Limited research has been conducted to understand how a mechanical anchor performs in a coal rib. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted the study described in this paper to define the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of a mechanical rib bolt. Based on the strength of the coal seam and the conditions of the coal mines, the bolts were installed at different amounts of torque. A typical tri-linear load-deformation response was obtained from these tests. It was found that the anchorage capacity depends on the coal strength, and the anchorage stiffness depends on the installation torque. The outcome of this research provides essential data for rib support design. INTRODUCTION Rib falls are a serious hazard in underground coal mines. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Although resin bolts has been used increasingly in the last few years to control coal ribs, mechanical bolting (mainly expansion-shell bolts) is still used in many underground coal mines. Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 79% of the mines determine their rib support requirement based on the depth, mining height, and the loading conditions, of which 35% use the conventional mechanical bolts. Conventional mechanical bolts are preferable for rib support because they do not require the miners to be too close to the rib during rib bolting. Hence, using the conventional mechanical rib bolts can reduce the risk of injuries and fatalities during the installation process. The mechanical bolt or the point-anchored bolt is the oldest type of rock bolt that is still in use today. The point-anchored bolt is a tensioned bolt anchored down the hole with a mechanical expansion shell or a grouted medium (Peng and Tang, 1984). Figure 1 shows the components of the mechanical anchor bolt. The mechanical anchor bolt consists of a plug, a shell anchor, a headed smooth bar with the top end threaded, a bearing plate, a hardened washer, and sometimes a friction-reducing washer. The shell anchor can be either standard or bail type. The shell of the standard type is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the smooth bar is generally 5/8 in for the #5 bolt or 6/8 in for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the wedge down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall.

Jan 1, 2019

By Emily Wortman-Wunder

As the 2013 president of the Society for Mining, Metallurgy and Exploration, Inc., I am pleased to present the 2013 issue of the Transactions of the Society for Mining, Metallurgy and Exploration, Vol. 334. The timely publication of professional papers that promote the advancement of scientific and technical knowledge is critical for enabling technology transfer. SME plays a key role in this process through its publications. Communication within the mining community is the key to a successful profession and society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2013 Transactions contains 73 papers covering most every aspect of the mining life cycle and encompassing the diverse sectors of our industry including coal, industrial minerals, metals, health and safety and computational methods. It includes all 18 papers published in 2013 in the Technical Papers Section of Mining Engineering magazine (Vol. 65) and all 33 papers published in 2013 in Minerals & Metallurgical Processing (Vol. 30). Additionally, this volume contains 22 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. Some of the many research highlights from 2013 include discussions of perennial issues, such as how to adequately prepare the next generation of mining engineering students for the workforce (Frimpong et al., pp. 44-52) and how to predict and prevent coal mine bursts and bumps (Pariseau, pp. 60-68), the highly anticipated February Rare Earths issue of Minerals & Metallurgical Processing, and papers analyzing electrical injuries in the U.S. Mining industry (Homce and Cawley, p. 367-375) the latest in assessing the safety and efficiency of operations. All 73 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2013 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2013

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986

By Raymond T. Moore

The Federal Coal Mine Health and Safety Act of 1969 (FCMHSA) begins with this statement: "Congress declares that the first priority and concern of all in the coal mining industry must be the health and safety of its most precious resource -- the miner; . . ." At the Federal level this responsibility is shared by the Department of the Interior and the Department of HEW. The health research and standard setting activities under the Act are largely the responsibility of the Department of HEW, and with the exception of Title 4, Black Lung Benefits, have been delegated to our Institute, which I will refer to henceforth as NIOSH. In addition, we bear certain joint responsibilities with the Department of the Interior. These include dust sampling and respirator approval. To complete the picture, the Department of Labor has recently assumed Black Lung Benefit respon¬sibilities from the Social Security Administration under Title 4 of the Act.

Jan 1, 1974

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture properties of a number single and multiphase brittle materials has been investigated. The reduction in the impact fracture energies and particle strengths with and without pretreatment has been measured in precise single-particle experiments using the Ultrafast Load Cell. Variations in the fragmentation pattern caused by different pretreatments were assessed by measurements of the progeny size distributions. The differences in the effect of thermal treatment on single and multiphase materials are discussed based on the experimental results.

Jan 1, 1995

By R. L. Pozzo, I. Iwasaki

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying Faraday's law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a non- magnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-

Jan 1, 1988

By M. K. Boateng, K. Awuah-Offei

"Language barrier in a workplace affects workers’ productivity and safety. The objectives of this paper are to: (1) review the various approaches for breaking language barriers among miners; and (2) analyze the costs and benefits of these approaches, and make recommendations on the way forward. The authors achieve these objectives by reviewing the current approaches in breaking language barriers among miners. The review reveals that some of these approaches can be expensive with less benefits. Thus, it is concluded that mining companies should carefully select the optimal approach to break language barrier. INTRODUCTION Multi-national mining companies have expanded their operations into non-traditional mining destinations to grow and meet market expectations. For instance, Newmont Mining Corporation has about 14 operations and projects located in Africa, Asia, Australia and America (Newmont Mining Corporation Operations and Projects, 2015). Similarly, Freeport-McMoRan operates about 14 mines in North America, South America, Southern Asia, and Africa (Freeport-McMoRan Inc., 2015). Some mining companies have also attracted expatriate workers into their workforce. For example, Ma’aden, the Saudi Arabian mining company, in its 2013 annual report states that 34% of its total employees are expatriates (Ma'aden, 2013). Expatriates constitute a key source of skilled labor and facilitate skill transfer. The success of many international operations relies greatly on expatriate performance (Erbacher, D'Netto & Espana, 2006). Even companies that do not expand their operations into other foreign countries still have to deal with language barriers due to changing language demography of the country and the areas from which labor is sourced. For example, the language composition of the workforce and languages used in South African mines is diverse with miners proficient in Afrikaans, English, Zulu, Xhosa and others to varying degrees (Research Focus (Pty) Ltd, 2011). As a result of these trends, most mines today operate with a multinational workforce. This means cultural differences, including language barriers, exist among the miners. Marschan-Piekkari, Welch and Welch (1999) emphasize the fact that language problems become prominent as companies internationalize and grow their operations into more countries. According to a survey by Forbes, language barrier affects operations. For example, business owners acknowledge that language proficiency may promote a safer work environment (Rubin, 2011). A research has shown that language and cultural barriers in a workplace contributes to reducing workers’ productivity, increasing accidents, and hurts employers’ ability to recruit, hire and retain workers (Morris, 2002). Hence, mines are making efforts to break language barriers in their operating environments. Ma’aden, for instance reported in 2013 that 1,506 of its employees received training in English as a second language (Ma'aden, 2013)."

Jan 1, 2016

By D. Jacobson

There are many different machine design parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the speed at which the cone gyrates. In June 2012, pilot tests were conducted to determine the production and operating conditions over a wide spectrum of speeds. mining operations will have variations in the ore characteristics and feed rates that result in non optimal use of the crushing energy and inconsistent process control. This study documents the measured variation in production and energy efficiency with two operating modes. Overall, the results match the theory, and the capacity and power fluctuated by 25% and 17%, respectively, when operated at full capacity, with an overall trend of slightly coarser discharge size distribution as the speed decreased. Using a fixed feed rate, the crushers had 4-14% higher production when operating at the optimal speed. Secondary analysis showed that the power draw consistency and magnitude of power spikes could also be improved by optimizing the cone speed. Varying the speed of the crusher can be used to tune the crusher during commissioning, adapt to changing ore conditions over long periods of time or be used as a dynamic input into an advanced control system. each action above would serve to make the crusher(s) more productive, more energy efficient, impove process control and would also have mechanical benefits for the machine

Dec 1, 2013

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

By John M. Karpinski

A method and equipment have been developed Tor measuring the impact strength of grains of brittle materials. It is shown that brittle materials develop a characteristic particle size distribution when fractured by impact. A simple mathematical model has been found to describe this distribution, and one of the parameters of the model has been designated the r value. The r value is directly proportional .to impact energy and, for fixed impact energy, it becomes a useful criterion of grain strength. Data are presented on the variation of the r value as a function of sample history, initial size, energy input and number of impacts, The results are interpreted in terms of the flaw theory of brittle fracture.

Jan 1, 1964

By W. G. Miller

A series of computer programs for the analysis and mapping of coal-related data has been developed at the Illinois State Geological Survey; these programs, known collectively as the Coal Data System, represent the latest achievements in computer processing of geologic data at the Survey. Building upon programs previously developed in the Survey's Computer Services Unit, they expand the scope of the computerized data base that the Survey has been using for analyzing coal-related data. The System was partially developed during a joint study by the Illinois State Water Survey and the Geological Survey entitled, ?Coal and Water Resources for Coal Conversion in Illinois.? 2 In that study the available coal reserves more than 42 inches thick in the two principal coal seams throughout the state were mapped. The System was used to calculate the coal reserves and to report the average number of tons of coal in place per square mile in each township (Figures 1 and 2). It also produced maps of the coal features of sufficient quality to be printed on material that was scribed as master copy for the printing of full-color 1:500,000 scale maps (see Figures 3 and 4).

Jan 1, 1975

By S. P. Lucido, I. Iwasaki

The potential of controlling heavy metal ions in effluents from discontinued mining operations and waste rock piles has been investigated. A fresh water green alga, Cyanidium caldarium, was found to have the potential to remove Cut' from solutions while exhibiting high tolerance to acid conditions which are commonly encountered in copper-nickel mine drainage. The process has the potential for application as a low maintenance metal decontamination system. The growth requirements and copper removal characteristics of this microorganism are described.

Jan 1, 1991

By V. R. Manukonda, I. Iwasaki

Selective flocculation of iron ores is extremely sensitive to the type and amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and the selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1988

By William R. Groseclose, Cecil E. Tackett

Since 1965 when the first mole was used on Bureau work, the Bureau of Reclamation has completed 17 tunnels of over 5,000 feet in length. The longest was 12.8 miles. Total length of the 17 tunnels was 376,207 feet, or over 71 miles. The finished diameter varied from 7 feet 0 inch to 18 feet 0 inch with 82 percent (58 miles) being less than 12 feet 0 inch in diameter when lined. All of these tunnels except one are gravity flow, water conveyance tunnels with relatively flat gradient. One is a low-head pressure tunnel. All were constructed by contracts resulting from fixed-price bids. Starting in 1964 the Bureau of Reclamation initiated the practice of giving several options in the specifications on methods of tunnel excavation. Since that time, construction work has been completed on 17 tunnels. Of this number, 11 were mole excavated and 6 were excavated by conventional drill and blast methods. In general, there has been 2 feet of mole excavation for every 1 foot of drill and blast. Cost comparisons are based on only 13 tunnels because the Bureau has 4 recently completed tunnels that have pending claims; therefore, final cost data are not available. Some definite trends show from the data available; however, the number of completed tunnels in some categories is so small the results cannot really be considered a trend. As more data become available, the indications will become more reliable. The information is presented to indicate general trends and comparisons and cannot be meaningfully used for a one-on-one comparison because of individual tunnel differences not considered.

Jan 1, 1974

By Manfred Hager

The ability of conveyor belts to transport large mass throughputs economically over previously unprepared ground has resulted in this system achieving great and extensive use. A significant component in this development is the conveyor belt itself. The development of high strength steel cord conveyor belts involves the optimising of splice design, the use of excellent rubber material especially in the splice, good craftsmanship during splice production and modern field vulcanisation equipment. The durability of a splice for belts of class St 3000 up to St 790 is expressed by the fatigue strength under dynamic stress. The results obtained with a test method and equipment developed by the University of Hannover indicate the present state of the art in this field. Belts of high nominal strength used on inclined long distance conveyors reach splice fatigue strengths of about 3000 N/mm. The design should only exploit approximately 50% of the fatigue strength determined in the tests as maximum operating stress. IMPORTANCE OF CONVEYOR BELT SYSTEMS The use of conveyor belt technology has expanded considerably over the last decades in the bulk goods transportation sector. Because of the favourable transport costs and the technology's adaptability to specific topographies, belt conveyors frequently represent the most economic solution. When flows of goods are large, as in German lignite mining operations, where masses of up to 40,000 t/h are given, it is the only technically feasible alternative. The use of belt conveyor systems allows the sensible distribution of the waste and the production of the coal (Hager, 1981). But this transportation alternative is also suitable when the masses involved are smaller. Whereas conveyor belts were only suitable for loose bulk goods up until a few years ago, today they are frequently also used for hard rock open cast mines, e.g. in the production of copper ore. Because of the favourable transport costs it is frequently still economic to use mobile crushers with a throughput of up to 10,000 t h 6 which breakdown the large blocks produced y explosives into transportable grain sizes. In many operations, trucks are only used to provide flexibility between the excavator and the crusher, i.e. over short routes, and the long, frequently steep, transport paths to the processing plant or to the spreader are undertaken by belt conveyors (Einenkel et al., 1992). The advantages of belt conveyors, i.e. to cope with large mass flows over inclines and down slopes of up to 1:4 have resulted in this system gaining very extensive use throughout the world. The conveyors can be installed over for the most part unprepared ground with suitable vertical radii, adapted to the locally available belt material. In the process individual conveyor belts with lengths of up to 15 km, and in the underground sector with lift heights of up to 1 km, have been built and operated. This great variety of application possibilities is complemented by a limited ability to pass through horizontal curves. This can be achieved with the help of design measures on the conveyor whilst bearing in mind the characteristics of the belt. STRESSING OF CONVEYOR BELTS IN DIFFERENT TYPES OF PLANT The advantage of conveyor belts compared with other systems is also to be found in the large available service-time window, i.e. the excellent reliability and the low costs of energy consumption and maintenance. It is in particular the reliability of a belt transport system which depends to a great degree on its main component, that is the belt - in all its different types and variations. For this reason, the belt is also given the greatest attention in the development of the individual components, because it is the belt which must be designed optimally with regard to various factors. The specific properties of the conveyor belt then assert a considerable influence on the design and sizing of most other components in a

Jan 1, 1993

By Eleanora I. Robbins, Motoaki Sato

Many problems associated with acid mine drainage (AMD) are caused by the complex way molecular oxygen (O2) oxidizes reduced matter at surface temperatures. In aqueous solution, O2 kinetically "prefers" to go through the formation of hydrogen peroxide (H2O2) as an intermediate. Being innately unstable, H2O2 is quickly decomposed back to water and oxygen in the presence of dissolved Fe and Mn, both catalysts for the decomposition. Direct addition of H2O2 to AMD produced similar results. Ozone (O3) is a much faster and stronger oxidizer than either O2 or H2O2. In the laboratory, O3 rapidly precipitated Mn, Fe, Ni, Co, Pb, and Ag even in acidic solutions. The experiments indicate that AMD can probably be processed with ozone and metal oxides/hydroxide recovered in flow systems using only septic-tank-size reactors and small sedimentation ponds.

Jan 1, 2000

By M. Ramachandran, R. G. Reddy

"A direct route for the reduction of magnesium oxide to magnesium using thermal plasma processing, with methane as the reducing gas, has been systematically evaluated. A feasibility study of the reduction reaction has been performed on the MgO-CH4 system at different methane concentrations and temperatures. The effects of changes in the key process parameters, such as the oxide-to-methane ratio and plasma power, on the yield of magnesium have been systematically evaluated. A maximum yield of about 61 mol% Mg was obtained using power of 20.0 kW and a molar ratio of MgO:CH4=1:1. Phase, morphological, elemental and binding energy analyses were performed on the product powders to understand the reduction reaction. Surface oxidation was observed in smaller magnesium particles in all the experiments, while the in-situ sintering of magnesium rods was observed at a molar ratio of MgO:CH4=1:1.5. Magnesium carbide (Mg2C3) was observed in the product, and its mechanism of formation is proposed using phase equilibrium data and a predominance diagram.IntroductionMagnesium has an excellent combination of low density and high strength. These properties have increased worldwide demand for and use of magnesium. Two major processes are used in the commercial synthesis of magnesium metal. The first method is electrolytic reduction and the second is thermal reduction using Pidgeon process. These processes can be classified as traditional techniques, but there are numerous emerging technologies that aim at reducing the production cost of Mg, its environmental impact and energy consumption. Thermal plasma processing is one emerging technique that has great potential in all the abovementioned key areas of magnesium production.Traditional reduction techniques. Two major reduction techniques, namely electrolytic and thermal reduction, have been used in the commercial production of magnesium. Electrolytic reduction is typically carried out in electrolytic cells from magnesium chloride (obtained from seawater or well and lake brines) (Tripp, 2009). The following simplified reaction shows the reduction of magnesium chloride to liquid magnesium and chlorine gas:"

Jan 1, 2015

By A. W. Khair, S. S. Peng

Discussion by J. Parker Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa(4000 and 7000psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic'? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition of moisture, from sprays or from humid air? Did moisture weaken the rock? Did it cause the rock to expand quickly, thus to induce internal compressive stress? How can the near-vertical cutters, as shown in the photographs, be attributed to primarily horizontal stresses? Did the cutters follow any particular pattern in the development panels, which might be related to a particular stress pattern? For example, did they always appear alongside the stiffest pillar? Or always along the northwest rib? Was there any evidence of the pillars and entries "rotating" under the influence of differential horizontal stresses? How much did the entries and pillars rotate as the longwall face approached and passed? After rooffalls, did the openings assume shapes which would indicate a preferred shape in that stressfield and geology? Did crosscuts always survive without damage, as shown in the sketch?

Jan 1, 1992