Search Documents

By Elwyn King, Donald J. Dodds

"...Unfortunately, the research activities in soil mechanics had one undesirable psychological effect. They diverted the attention of many investigators and teachers from the manifold limitations imposed by nature on the application of mathematics to problems in earthwork engineering. As a consequence, more and more emphasis has been placed on refinements in sampling and testing and on those very few problems that can be solved with accuracy. Yet accurate solutions can be obtained only if the soil strata are practically homogeneous and continuous...." This statement about soil mechanics was made by Karl Terzaghi, thirty years ago and applies to a greater degree today to the infant science of rock mechanics. More uncontrolled variables are added to the already many existing in soil mechanics. Variables, such as Macro-discontinuity and in situ stress levels. In no other field of engineering are the problems as site oriented. Presently this site dependance demands the investigator or rock mechanics engineer to get his hands dirty rooting in the muck of a tunnel floor trying to properly install or readout test apparatus in a comprehensive site investigation. This paper discusses such a site investigation designed to determine the problems and solutions inherent in the driving of the Trans Koolau Tunnel. The paper will describe the various types of tests to be performed, how the results are to be used and the interrelation of the various tests themselves.

Jan 1, 1997

By William J. Miles, Raymond E. Blair

Introduction There has been much publicity of the boom and bust in oil and gas well drilling in the US, and many comments on oil and gas gluts. Despite this, the drilling industry remains the largest consumer of functional industrial minerals. The boom years of 1981 and 1982, compared with the bust year of 1983, show a sharp reduction in the consumption of industrial minerals-1981, 7.4Mt (8.2 million st); 1982, 6.3 Mt (7 million st); and 1983, 4.4 Mt (4.9 million st). Industrial mineral use rebounded in 1984 to 4.7 Mt (5.2 million st). This was the second highest year in history in terms of wells drilled and third highest in footage drilled. Table 1 shows the history of drilling activity and mineral consumption from 1971 to 1984. The uses of functional industrial minerals in oil and gas well drilling were detailed by Miles and Blair (ME, 1983, October, pp. 1397-1400). As an update, this article addresses only the changes that have occurred in the industry in the past two-and-a-half years. It will be directed to mineral use and new products introduced to the industry. Drilling practices A partial explanation of where wells are being drilled with lower quantities of minerals consumed is: • In the boom year of 1981, there was a proliferation of number of suppliers chasing the same business. This resulted in multiple sourcing, multiple warehousing, and a huge increase in inventory that became surplus in the following years. The bust year, 1983, caused a severe shakeout in the number of suppliers of minerals and associated drilling fluids. • In 1981 and 1982, the wild speculation in the oil and gas industry led to drilling of speculative deep gas wells. Oil wells were drilled on a wildcat basis - in areas of unproven productivity. • Presently, the oil and gas well drilling industry is very active. But drilling is directed toward proven areas of production and working over old wells for increased production. This means a large number of wells are being drilled with lower average foot-

Jan 11, 1985

The National Mining Hall of Fame and Museum (NMHFM) in Leadville, CO will induct the class of 2011 on Sept. 10, 2011. Representing the coal, metallurgical/processing, research and development, marble and lead industries, this year?s inductees cover a diverse crosssection of the mining industry. William Francis Diamond, Wayne Hazen, Redfield Proctor and Jeffrey Zelms will join 210 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 24th Annual Induction Banquet and Ceremony. The members of this year?s class were selected for being visionaries, leaders and ambassadors both within their own sectors and across the industry at large. Diamond had an illustrious engineering and managerial career that spanned four decades with Island Creek Coal Co. During that time, he was responsible for the engineering and construction of the deepest coal mines producing in North America at the time.

Jan 1, 2011

By William M. Turner

Thermonics is a methodology of ground-water flow system analysis based upon the distribution of heat within the subsurface as influenced by moving ground water. Thermonics is based upon the Stallman Equation 1 (1) which describes the simultaneous transfer of heat through a porous medium which contains moving ground water. The Stallman Equation is:

Jan 1, 1980

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Occasionally, standing supports are used to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for standing supports to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. The Mine Roof Simulator (MRS) was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. Prop models were used to study the effect of a range of roof and floor materials — gray shale, shale and claystone — on the critical buckling loads of the steel props.

Dec 1, 2022

By Noel C. Joughin, Orrie Fenn, Brian E. Protheroe

Work has shown that the use of high-pressure water jets enhances the performance of mechanical cutting in very hard rock. To assess the potential of this approach for use in conjunction with free rolling cutters, a series of tests has been conducted using both disc and button type cutters, to determine the relative effects, on cutter performance, of variations in relevant jet and cutting parameters. In these tests it was found that water jet assistance can result in reductions in the forces on a free rolling cutter typically of the order of 40%.

Jan 1, 1985

By R. Bishop, J. Baggett, J. Monsalve, J. Hole, N. Ripepi, A. Abassi

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karsts are complex and challenging ground control risks. Traditional methods of predicting karst locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features. Ground penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in material properties between limestone and open karsts causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries, however there is a lack of published research on underground mining GPR applications. The purpose of this work is to prove the viability of GPR in underground stone mines for karst detection, and to discuss the importance of karst detection ahead of mining. INTRODUCTION The Mine Safety and Health Administration (MSHA) currently lists 116 active underground stone mines in the United States, the vast majority of which extract limestone for crushed stone products. These limestone mines have the potential to encounter karst voids at some point in their operation, as most karstic regions of the United States develop in limestone rock masses (Kuniansky, Weary, & Kaufmann, 2016). Karsts, the cavities formed by the dissolution of carbonate rock, have long plagued the mining and tunneling industries, as well as been a hindrance on the Earth’s surface, producing sinkholes and ruining otherwise valuable land for construction and public use. The impact of karsts on the Gavarres tunnel in Spain is well documented by Alija et al; constant instability conditions, material spills into the tunnel, and unexpected cavities seriously delayed the project deadlines and “were not foreseen in the design” (Alija, Torrijo, & Qunita-Ferreira, 2013). At the water supply project in Sohngua River, China, Bin et al detail the presence of both water and sediment filled karsts which are sources of disastrous conditions at this tunnel (Bin, et al., 2017). A hydrological tunnel in Lebanon encountered numerous massive karsts in the tunneling path which required remediation via friction anchors, rockbolts, welded wire fabric, channel steel arch segments, invert steel beams, and shotcrete (Leech, Jaoude, & Ghanem, 2008). From a design standpoint, rock mass classification schemes, such as the RMR from Bieniawski and the Q-system from Barton, are not able to represent the true nature of a karstified carbonate rock mass, and therefore complex case-by-case analyses of underground conditions are necessary (Andriani & Parise, 2017).

Jan 1, 2019

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

By H. Wen

"Taking the long flame coal, gas-fat coal and anthracite as samples, we tested the adsorption quantity to single component gas of N2, CO2 and CH4 under atmospheric pressure phase at different temperatures. Then we analyzed the adsorption characteristics and models of different metamorphic coals. The results show that metamorphic grade, temperature and gases species are main factors to adsorption quantity of coal. The higher and lower metamorphic grade of coal have greatly influence on adsorption capacity while moderate grade of coal has opposite result. The coal adsorption amount to three single component gases under the same experimental condition is CO2> CH4> N2.The simulation precision order of four adsorption models is quadratic curve model > Freundlich isotherm model> Langmuir model >logarithmic curve model. Quadratic curve model and Freundlich isotherm model both can accurately describe the adsorption behaviors of N2 and CH4, different isothermal adsorption curve of CO2 needs two kinds or more models to describe. This has a reference value to the study of adsorption characteristics and models to single component gases.INTRODUCTION Adsorption is the interfacial phenomena that concentration of single or multiple components in the interface layer is different from the bulk phase (1964). Adsorption model is mathematical models to describe the adsorption characteristics of the adsorbent, mainly reflected to fitting effect of gas adsorption isotherm, which contribute to deeply understand the adsorption characteristics of adsorbent. Many scholars have carried out extensively experimental studies of the coal adsorption process from different angles. Zhao (2010) studied the influence of coal metamorphism to pore development of coal seam through a variety of experimental methods. Zhang (2006) analyzed the adsorption capacity and the controlling factors from three aspects of the coal rank, maceral and coal mass deformation. Cheng et al., (2002) studied the influence of pore size distribution of different rank coals to adsorption constants. Zhong (2002) carried out varieties of isothermal assay and established the prediction method of coal seam adsorption affected by a variety of conditions. R. M. Bustin (1998) proposed that we could not simply describe the change law of coal adsorption capacity and maceral content by a fixed parameter, and the adsorption capacity of the same coal rank also has great change. C. R. Clarkson et al., (1997) used four different adsorption models to describe the coal methane adsorption process, and the fitting precision of adsorption models is D-A equation >D-R equation > BET equation> Langmuir equation. Gasem, K et al., (2003) found that the fitted isothermal adsorption curve of D-A equation and BET equation are better than Langmuir equation under high pressure condition, while D-R equation and BET model are better to CO2 adsorption. In recent years, scholars’ at home and abroad research achievements of coal adsorption focused on high-pressure stage (about 0~15 MPa), mainly for coalbed methane exploitation, carbon dioxide trapping and sealing technology development, but the study of coal adsorption under atmospheric pressure phase is little. In this paper, we analyzed the adsorption characteristics and models under atmospheric pressure phase, it has a reference value to the study of characteristics and models to single component gas."

Jan 1, 2015

By John Keay, Douglas R. Shaw, Gregory J. Olso

Rhodes Mining NL, Perth, Australia, is developing the Lahoca Gold Project which is located in Hungary, about 30 km from the town of Eger. The preliminary resource is estimated to contain approximately 1.5 million ounces of gold. The project is being evaluated for an annual process capacity of 2 million tonnes. The test samples contain just over 2 g Ault and 6% sulfur as sulfide. Copper and arsenic levels are approximately 0.2 and 0.1 %, respectively. The ore is refractory due to submicroscopic gold occurrences and structural associations with pyrite. A small amount of the gold is finely encapsulated in quartz. Approximately 30% of the gold in the crushed ore is soluble in cyanide and up to about 55% is cyanide-recoverable with ultra­fine grinding. The ore has little preg-robbing ability. Metallurgical test work done by Colorado Minerals Research Institute (CMRI) and other investigators has shown that as much as 85 to over 90% of the gold was recovered by the relatively severe conditions of pressure oxidation or roasting of the whole ore or a flotation concentrate. The Lahoca ore responds to flotation with gold recoveries of 87% into a low grade concentrate. Subsequently, with a view toward defining a process route with potentially more attractive economics, Rhodes Mining and CMRI conducted an extensive review of biooxidation technologies and concluded that, in particular, heap biooxidation methods promised lower process costs which normally are associated with heap leaching. Based on the study, which included the analysis of the closely related practices of copper dump/heap bioleaching now well established in that industry, CMRI conducted simulated heap biooxidation experiments which evaluated factors such as ultra fine ore crushing, agglomeration techniques, heap design, forced aeration oxygen supply, and whether or not the heap is irrigated. Separate flask biooxidation tests at Little Bear Laboratories showed that the finely crushed ore is biooxidized readily, with a near linear relationship between sulfide oxidation and gold cyanide solubility. Gold recoveries of as high as 66% have resulted after biooxidation of crushed ore. This paper highlights the metallurgical developments of the Lahoca project, and focuses on recent biooxidation laboratory test work aimed at enhancing the treatment of crushed ore.

Jan 1, 1997

By Iga Trisnawati, Fitria Puspita, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Idi Amin, Andi Nurfaadhilah Ulfah

Laterite ores, rich in essential metals like nickel, iron and cobalt, are a crucial resource for modern technology. However, the extraction of nickel from laterite ores is a complex process due to their intricate mineral compositions and low nickel concentrations. This paper presents the results of a study to understand the leaching behavior of preroasted laterite ore and the impact of roasting on leaching kinetics. The ore was subjected to roasting at 280 and 610 °C for a duration of three hours, followed by leaching in sulfuric acid (H2SO4) under atmospheric conditions. The results show that preroasting the ore at 610 °C significantly improved the recovery of nickel during leaching, with recovery rate of up to 93 percent, and the leaching process of the preroasted ore was primarily controlled by diffusion through the ash layer. The activation energy values were found to be 20.97 kJ/mol for the ore roasted at 280 °C, and 18.97 kJ/mol for the ore roasted at 610°C. These findings suggest that preroasting can enhance the leaching performance of laterite ore, potentially paving the way for more efficient and sustainable nickel extraction processes.

Aug 1, 2024

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010

By Thomas P. Meloy

There is much interest in the automation of entire comminution circuits, At the present technological level it is possible to automate a circuit but to date it has not been done, To successfully automate a circuit, a number of problems must be solved. Not all of them are engineering problems. The purpose of this paper is to discuss some of these problems, as certain the implications of these problems and indicate solutions to them. In this paper the term "automation" is used loosely but in the popular sense. Namely, that a plant is automated if a computer is used to control the basic flow of the materials as well as setting the critical parameters in the process. Specifically, the discussion will concern itself with the control of comminution circuits from the dumping of the ore into the primary crusher until the final interface between the comminution circuit and say, the flotation mill in the case of a sulfide ore.

Jan 1, 1965

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

By E. R. Mueller

The natural lives of machines and components vary tremendously! Maintenance managers struggle constantly to maximize their equipment lives while minimizing their maintenance costs, but they normally lack the tools and techniques they need to do this properly. This paper proposes a methodology based on probabilities of failure and expected values for repairs that recognizes the variation among individual machines and components as well as the high costs associated with catastrophic failures. It enables a user to determine the optimum change-out intervals for many types of equipment. The approach proposed here is sophisticated enough to be reliable but simple enough to be applied by the maintenance staff on the shop floor. It will complement existing preventive and predictive maintenance programs.

Jan 1, 1995

By Donald C. Moore

Introduction Asamera Minerals (US) Inc. and its joint venture partner, Breakwater Resources Ltd., discovered ore grade gold mineralization on their 20 km2 (5000 acre) Wenatchee, WA land position in February 1983. Due to the high grade nature of the discovery ore and the known reserves of ore in the "B Reef&apos; and "B West" zones previously outlined by other companies, a decision was made to construct a mine/mill operation near the known ore occurrences. Further drilling in the discovery area quickly expanded known gold occurrences to more than 3.6 Mt (4 million st) with tentative in-place ore grade of 7 g/t (0.25 oz per st) and minor silver values. Based on existing knowledge of the ore body and the rapidly increasing ore reserve, a decision to build a 1.8-kt/d (2000-stpd) mine and mill complex was made in the second quarter of 1983. A schedule was devised to begin immediate mine development, shaft sinking, environmental and land use permitting, and mill and tailings dam construction (Fig. 1). Meeting the scheduled startup date, April 1, 1985, required a fast track schedule in all areas. To this end, Asamera purchased the Oracle Ridge Partners concentrator. This was an assemblage of new equipment designed for use as a copper concentrator in southern Arizona. The purchase contained all of the major mineral dressing equipment - crushers, screens, rod and ball mills, etc. and an engineering package. It did not include most of the other required items, such as buildings, conveyors, pipelines, tanks, and pumps. At the same time, core samples were sent to two independent process development laboratories for initial flowsheet development. Due to the refractory nature of the carbonaceous ore, cyanide leaching was not feasible. Flotation was selected as the concentration process. Further testing showed that autoclaving of the flotation concentrate followed by cyanidation would result in overall recovery of about 85% gold. A mine manager was hired to begin assembling an operations staff, hire an environmental consulting firm, and begin mine development. Environmental and land use concerns were major obstacles due to the mine&apos;s close proximity to a city of 20,000 people. These concerns had to be rapidly defined so as to mitigate any adverse impacts from and mining processing operations. Baseline data dealing with weather, air and water quality, and sound were measured before start of mine construction. Concentrator and flowsheet development remained static until October 1983 while definition drilling and mine development proceeded. In late October, a process engineer was hired to coordinate development of a process flowsheet, purchase the remainder of the concentrator equipment, prepare a concentrator construction contract, finalize concentrator detail engineering, and combine environmental and process requirements with a tailings dam design. Process development There were only 17 months remaining to mill start up from the hiring date of the process engineer. Therefore, the process flowsheet had to be finalized rapidly. To accomplish this, samples of drill core from the highest grade (and therefore potentially the most commercial) ore zones were sent to an outside metallurgical laboratory to confirm beneficiation tests on the flotation process. Test results again showed that flotation would provide about an 86% gold recovery. Therefore, all further testing was concentrated on flotation and autoclave/cyanidation of flotation concentrates. Focusing on a well known process such as flotation was important in accomplishing the rapid design and construction of the concentrator. If, during these next phases, we were continually changing design concepts, layout, and process flow, the mill startup would have been delayed many months. Once a process flowsheet is selected the process engineer must obtain the process criteria needed to design the beneficiation system. For example, it was known in early December that the Oracle Ridge rod and ball mills were too small to grind 1.8 kt/d (2000 stpd) of Wenatchee ore. A decision had to be made to purchase a large, used ball mill and convert the Oracle Ridge ball mill to a rod mill. The process engineer must be cognizant of the process criteria needed to size and select equipment. If not, the process engineer must use the professional services of the equipment manufacturing companies to review the requirements that the equipment is asked to perform. For the Wenatchee system, this resulted in the adaptation of a ball mill to a rod mill with a weight limit of grinding rods to protect the mill bearings and drive trains. When a decision is required, the process engineer has to present the facts and options in a manner that allows a rapid decision. This information must include costs, equipment availability, and effect on the construction schedule. At the Cannon mine, there were process development details that resulted in decisions similar to the ball mill purchase. These included an increased flotation residence time from eight to 25 minutes, an increased thickener area requirement, a high pressure tailings pumping system, and area constraints in plant layout. All of these decisions had to be timely and required assistance from manufacturers&apos; service engineers, and knowledge of the alternate costs and effects on construction completion. Equipment procurement It was decided in early 1983 to build the ore milling facility with Oracle Ridge equipment, augmenting it with used equipment

Jan 2, 1989

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By William G. Pariseau, Mark K. Larson, Heather E. Lawson

Rational design based on engineering fundamentals is essential for the layout of safe, stable shafts and tunnels. Shafts and tunnels including winzes, raises, adits, and crosscuts are lifelines to the underground and must be secure. The contribution of this paper describes a significant extension in existing software previously developed for five important design problems in strata-bound mines such as coal, trona, salt, potash, and some large, lead-zinc mines. This extension in software allows analysis to proceed in three easy steps: (1) preparation of a strata properties file, (2) generation of the finite element model, a mesh, and (3) finite element program execution. Circular, elliptical, and rectangular shaft sections are available for a single shaft, twin shafts, and shafts in a row. Spacing of twin shafts and shafts in a row is a free parameter (pillar width). Tunnel shapes are the same as shafts but include the conventional arched back section. Dipping strata of variable thickness, depth and orientation relative to the excavation of choice are allowed. The analyses are three-dimensional. An elastic-plastic material model based on associated rules of flow and an N-type yield condition for isotropic, transversely isotropic, or orthotropic rock are used for all strata. Example analyses from several hardrock mines are provided to illustrate the three-step process including mesh plotting and plotting of selected results. The goal of this software is to advance mine design technology for improved miner health and safety.

By J. Finch, J. Yianatos, N. W. Johnson, R. Espinosa-Gomez

A method of determining the maximum concentrate solids rate or carrying capacity is described for given column operating conditions. The method requires alteration of the feed rate of solids to the column at a fixed residence time by manipulation of the % solid of the column feed pulp or the bias rate. The carrying capacity was measured for five streams at the Mt. Isa Mines Pb/Zn and Cu concentrators. As a potential scale up parameter, the mass of solids per unit time per unit column cross section (Ca, g/min.cm2) is explored. Ca is tentatively related linearly to the 80% passing size (d80) of the concentrate. For d80 < 15 pm Ca was less than 4 g/min.cm2 (8 lb/min.ft2) which makes it a critical consideration in scale-up for such fine feeds. An alternative carrying capacity parameter, mass of solids per unit volume of gas Cg was not as useful as Ca since Cg varied inversely with gas rate.

Jan 1, 1988