Search Documents

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By Yuji Tsuneno, Yoshikazu Mikami, Yasuo Takeuchi

A new device was successfully developed in order to overcome the difficulty of drilling longer holes for anchors in soft soil bedrocks or swelling bedrocks, which is one of the major impediments to rapid excavation by NATM (New Austrian Tunnelling Method). With higher rotation (1200 - 1800 r.p.m.) and lower percussion energy (4 - 6 kg.m), the new drill has following advantages: (1) Applicability covers soils and medium hard rocks with the same drifter. (2) Longer hole (more than 9m) is achievable only with air flushing even in cohesive soils or rocks. (3) Better borehole stability is obtainable even in earth or in fissured rocks.

Jan 1, 1981

By Jozef F. Zurawski

The paper discusses design and construction of a 1.8 meter (6 ft.) diameter tunnel installed under complex geology of Staten Island, New York. Contract T-13 is a section of the Oakwood Beach Water Pollution Control Project constructed for New York City Department of Environmental Protection. A knowledge of the subsurface conditions and difficulties experienced on the adjacent contracts called for an innovative approach to handle tunneling under 12 to 17 meters (40-55 ft.) of water in the variable subsurface conditions. This paper describes tunnel design and construction utilizing continuous grouting during advancement of tunnel boring machine and installation of liner plates.

Jan 1, 1993

By S. D. Abbott

Mines are filled with a mixture of gases, some of which are toxic, flammable, or explosive. Others serve as early reporters of impending problems. Mines monitor these gases in order to ensure the safe, efficient operation of the facility and avoid losses or disasters. Two different approaches to monitor these gases have historically been taken. One kind of device measures the amount of each gas present by using selective detectors (e.g. handhelds and spectrometers). Another kind separates the mixture of gases into the individual constituents, then measures the amount of each gas present (e.g. gas chromatographs). Handheld units are the most widely used, but gas chromatographs are the most powerful yet underutilized units available to enhance mining operations. There are many misconceptions about the nature, applicability and proper use of each type of device, and little data is available. Up to this point, many people had only the manufacturers? claims to guide them. This study was undertaken to clarify the range of applicability, important characteristics, and value in use of these units in real-world situations. An additional goal of the study was to provide ways to evaluate comparative data, and thus aid mining operations in choosing the most beneficial and reasonable ways to use such devices in various situations and contexts.

Feb 23, 2014

By Daniel W. Kappes

In late 1995 at the Randol symposium in Squaw Valley, I gave a paper which described the Itos project flowsheet. At that time, project construction was nearly completed and stmtup was close. This paper describes the ltos operation since then. To summa­rize things, startup occurred partially in late 1995 with full start­up of all components in about mid 1996. From then until now, April 1998, the plant has been running at partial capacity and has yet to achieve full production rates.

Jan 1, 1998

By K. Kim, H. Gao

A site-characterization strategy formulated for the probabilistic assessment of rock mass properties is presented. The strategy, which takes into account the variability of rock properties and the stochastic nature of the rock-failure process, entails determining probability distributions of rock properties by utilizing extreme value statistics and Monte Carlo simulation. Laboratory and, field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass can be estimated by using this proposed method. The results of the analysis can be incorporated into the design of underground structures. Then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1997

By William Gleason

During the past five years, mining operations have had access to press technology for piping and joint fittings that can save owners a significant amount of time when installing or replacing pipes by eliminating the need for welding or threading. Viega, with North American headquarters in Wichita, KA, entered the mining sector in 2009, adding to its already expanding industrial sector. Since then, the company?s global engineering department has paid considerable attention to its industrial division, bringing its expertise in plumbing solutions for residential and commercial buildings to the mining and mineral extraction industry. ?We have a lot of applications in the mining industry.?We have a lot of applications in the mining industry throughout the United States, Canada and Mexico and continue to expand in the mining industry,? Tom Shields, Viega?s director for industrial accounts explained. ?Since we made the decision to increase our presence in the industrial markets, we have been aggressive and more than 240 applications have been approved by our engineering department in Germany.? Getting approval from Viega?s engineering department is no small feat. During a tour of the manufacturing facilities in Ennest and Großheringen, Germany, Mining Engineering, as well as a select few other publications and clients, were shown Viega?s manufacturing process. At the Ennest facility, hundreds of millions of fittings are produced, and each one is inspected mechanically and with a laser at the end of the production line. With four production facilities in Germany and one in the United States, Viega is able to ship to anywhere in the world. The company distributes everything from fittings to stainless steel pipe.

By Michael J. Miller

The demand and supply of wollastonite has gone through a dynamic period in the 1990's. A 10% -15% growth rate of demand stimulated interest in evaluating new projects. However, the mid-1990's brought declining prices for commodity applications and natural barriers to entry for technical applications, making many of these potential projects uneconomic. Successful projects that were brought to market were done so by incumbent producers. This work examines the competitive structure of the wollastonite market by evaluating the strategic decisions of the industry leader, NYCO Minerals Inc., and a new market entrant, Orleans Resources, in an attempt to identify the environmental threats and opportunities of this industry. Results suggest new entrants like Orleans Resources face significant entry barriers for technical applications, while NYCO Minerals could improve its profitability by having less exposure to commodity applications.

Jan 1, 1999

By R. S. Mateer

Linear programming on desktop computers is commonly used to optimize coal blending proportions. The objective function is usually the cost of the blend. The constraints consist of materials and heat balances as expressed as linear functions of the blend. This is illustrated in Example 1. Inclusion of a sulfur compliance constraint is more complex because the maximum permitted sulfur percentage is not a pre-specified constant. Rather, it is a function of the calorific power of the blend itself. The current limit of 1.2 pounds of sulfur dioxide per million Btu may be expressed as: Sulfur Max % = 0.6 • H/10,000 with H in Btu/lb.

Jan 1, 1994

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan, J. H. Kang

Previously we reported crushing or grinding crystalline silica results in silica-based free radicals on the particulate surface which can generate hydroxyl radicals in aqueous solution (1). Now we find that freshly ground silica is more cytotoxic to and a more potent activator of alveolar macrophages than similarly sized aged silica. Since the United States Department of Labor estimates that over 1.25 million American workers may be exposed to freshly ground crystalline silica arid nearly 60,000 may be at risk of developing some degree of silica-based occupational lung disease, then this is hardly a trivial problem. Occupations of concern include workers who come in contact with silica including miners of soft and hard minerals, stone quarry workers, glass workers and even millers who stone grind flour. Acute silicosis is manifested by inflammation, alveolar lipo-proteinosis, and the rapid development of respiratory disability that depending on the dose of silica can produce chronic silicosis which takes 20 - 40 years to develop. It is demonstrated by the appearance of concentric hyalinized nodular lesions and progressive development of dyspnea(3). Certainly the free radicals produced on the surface of freshly ground crystalline silica play a most important role in producing the acute and chronic symptoms of silicosis. When respirable-size freshly- ground silica (0.1 -- 5 microns in diameter) enters the deep alveolar spaces in the lung and contacts an aqueous environment, hydroxyl radical are generated and cellular damage is bound to occur. We have found that freshly ground silica can cause lipid peroxidation and lysis of erythrocytes(1). The objective of this investigation was to further elucidate the enhanced toxicity of freshly ground versus aged silica. It can be deduced from the data that not only is freshly ground silica more cytotoxic to alveolar macrophages but it is a more potent stimulant of these phagocytes. However the mere characterization of toxicity is not entirely helpful if there is not a useful means to detoxify the cause of the damage. We have identified an aqueously soluble substance that can be used in high dilution to detoxify the SiO(•) and Si(•) type of free radicals. This is the organosilane known as Prosil 28 (R). We have found that coating of the freshly ground silica can effectively reduce its toxicity. The importance of this observation is that such a coating could be used with water cooled drills. This may partially detoxify silica at the point of generation of the free radical, i.e., the generation of the fresh silica dust itself. Such a coating could be used in great dilution 1:103 or 1:104. The coating would be long lasting, inexpensive and should be non-toxic because of the great dilution.

Jan 1, 1991

By The SME Sustainable Development Committee

The evolution of sustainable development in mining is recognized as a key contributor to sustainable development (SD), which is defined as the ability of current generations to meet their needs without compromising the ability of future generations to meet their own needs (Brundtland, 1987). This includes, in equal parts, social, economic and environmental impacts ? triple bottom line (Munashinge and Shearer, 1995). Alternately, sustainability has been defined in relation to social, natural, human, physical and financial capital. Our way of life relies significantly on the materials provided by mining, while mining activity affects the triple bottom-line or the five capitals. The mining community and its professionals have come to realize the importance of engaging all stakeholders in the discussion on sustainability. SME, as the leading professional mining organization, has been involved in these discussions. The society has various initiatives in sustainable development for members and stakeholders. The objective of this article is to: provide historical context for current trends in mining and SD and share SME sustainability initiatives ? their goals and rationales ? with the broader mining community. This article is timely because the past year saw two landmark forums on sustainable development: Rio+20 ? the 20th meeting of the United Nations Conference on Sustainable Development, and MMSD +10, the Mining, Minerals and Sustainable Development project 10 years on. Furthermore, this year marks the 10th anniversary of the Milos Declaration on the minerals professional?s responsibilities in achieving sustainable development, forums in which SME was involved.

May 1, 2013

By R. S. Kasper

This paper reviews the procedure used to quantify the conveyor frictional resistance on a 3.9 km (2.4 mile) long overland conveyor belt. Field torque measurements of the three drives were used to help fine tune a computer simulation of the conveyor. This enabled the prediction of the effect on various conveyor components that cold temperatures will have on increasing the throughput tonnage.

Jan 1, 1995

By J. Brune

The need for reliable and adaptable underground mine communications has become a focal point for both the safety and logistics of a mining operation. New mine communication technology aims to connect personnel, equipment, and data together while setting up a network that can be utilized during normal operations and also in an emergency event. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) requires mine operators to establish post-accident, two-way communication between underground and surface personnel and electronic tracking for all mine personnel. Communications systems must be designed such that they can survive major mine accidents, including explosions, fires, inundations and ground falls. Typical, wire-bound communication technologies are vulnerable because wires are often destroyed in such accidents. Wireless technologies that work well on the surface, such as cellular telephone networks; have limited applicability underground because the wireless signals do not propagate through rock.

Feb 23, 2014

By Greg Struble

The Homestake Gold Mine is one of the deepest and most extensively developed hardrock mines in North America. The mine is divided into five divisions which produce a total of 1.7 million metric tons of ore per year. In the past, labor intensive mining methods such as open cut-and-fill, shrinkage, and timber stoping were utilized. In recent years there has been an extensive change to the more productive methods including Vertical Crater Retreat and Mechanized Cut-and-Fill. Also, the percentage of production from the lower divisions below the 4850 level is increasing while upper level reserves are beginning to decline. Combined, these factors have strained the ventilation resources to the limit. By early 1984 it became clear that future production trends would require a detailed study of future ventilation resources. By November of 1984 the Ventilation Department completed a study to project these future requirements. This paper will detail the first phase of a scheduled two phase upgrade: the installation of a new surface fan.

Jan 1, 1987

By J. Brune

The disaster at the Upper Big Branch (UBB) mine 2010 has demonstrated the destructive violence of a coal dust explosion by killing 29 miners in the worst mining accident the United States has experienced in almost 40 years. This explosion brought to light that the United States mining industry must strengthen explosion prevention and explosion hazard detection practices. Recent legislation such as the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) pushed the strengthening of explosion and disaster response and miner protection in addition to stricter regulations on the sealing of abandoned areas and on conveyor belt flame resistance. The focus of this new act was on how to respond to a disaster or explosion, yet not much improvement was made with respect to prevention explosion disasters. Researchers at the Colorado School of Mines have recently concluded extensive research into methane and coal dust explosion prevention practices and regulations as it may be applicable to underground mines in the United States. This research aims to forward more studies into the use and adoption of standards and procedures that have been utilized in countries with strong explosion prevention histories.

Feb 23, 2014

This paper examines the feasibility of combining network modeling and computational fluid dynamics for modeling of underground mine ventilation systems. Both simulation methods have specific advantages and disadvantages for analysis of mine systems. Network modeling is widely utilized by many operations and allows for assessment of current systems and simulation for planning purposes. Alternatively, CFD has been utilized only marginally by operations and is typically a research tool, requiring considerable computational power, complex models, and careful analysis and calibration of results. Network modeling allows for a holistic approach to the ventilation system, giving quantity, velocity and pressure in every branch, but CFD modeling can resolve the flow regime in 2-D or 3-D, which is idea when examination of an area on a more detailed basis is useful, such as dust and gas control. Integration of the two can allow for more flexible systems analysis. The feasibility of integration, along with application to limited underground mine data are examined.

Feb 23, 2014

By J. A. Pontius

The Cresson Deposit is located in central Colorado within the historic Cripple Creek Mining District. The deposit has moved from its initial discovery in 1990 to full production in less than five years (current reserve nearly two million ounces). This accomplishment required a great deal of cooperative teamwork between the exploration, development, permitting and corporate groups. Nowhere was this cooperation more evident than in the construction of the geologic block model. The detailed modeling of gold and its metallurgical characteristics formed the foundation upon which critical financial and design decisions were based.

Jan 1, 1995

By J. F. Dresser

Managing environmental compliance at a complex facility has the potential to bring a high degree of personal and professional satisfaction to both the corporation and the individuals responsible for day-to-day operations. The decade of the 1990's, however, has seen the emergence of a nationwide trend of aggressive federal and state civil and criminal enforcement for environmental violations. This trend, spearheaded by the U.S. Department of Justice (DOJ) and the U.S. Environmental Protection Agency's (EPA) Office of Enforcement, has the potential to place the corporation, its corporate officers, and compliance personnel at collective professional risk, as well as a growing tendency to place accountability on individuals. Management of environmental compliance has been anecdotally compared to a shooting gallery at a carnival, with the following exception: At the shooting gallery, successfully hitting nine out of ten targets usually brings a reward and recognition of shooting skill; hitting nine out of ten environmental compliance expectations not only brings agency consternation and negative publicity, but the "gallery" will likely shoot back with stiff fines and possible criminal allegations. Faced with the challenges of the new environmental compliance shooting gallery, corporations and professionals are often left asking themselves, "How do we (or more appropriately, can we) win at this game?" This paper examines recent federal enforcement statistics and offers several suggestions for coping with the responsibility of managing environmental compliance in the 1990's.

Jan 1, 1992

By Kuda R. Mutama, Allen E. Hall

A wind tunnel investigation into the fundamental characteristics of jet fan performance is described. The effects of varying fan positioning in a square tunnel cross section are reported for two fan outlet diameters and velocities. Tests were conducted, also for a jet fan placed in a flow developed by an external fan operating in the same direction as the jet fan. The position of the jet fan relative to the tunnel walls was found to affect its performance. Performance parameters were determined and used to formulate theoretical equations based on momentum and energy considerations. The results identified a range of flow ratios which can be used to design an effective jet fan ventilation system and provide a basis for the selection of jet fans for practical mining applications

Jan 1, 1997

By R. K. Singhal, D. B. Stewart

A variety of equipment is being used for roadheading and tunneling in the mining industry. In United States drum-type continuous miners are used most extensively. In Europe and Canada mine roadways are driven mainly by roadheaders. The application of tunnel boring machines to coal mining is somewhat recent. Such machines are however being used on major projects driving main mine entries.

Jan 1, 1985