Search Documents

By Robert H. Oliver

Flowsheet flexibility in new 750 TPH coal cleaning plant provides three unusual capabilities. Two compartment drum coarse H.M. washer can be adapted to provide two stage separation. Coarse section of plant can be operated without fine section when washing surface mined coal. Fine section can operate with flotation cells bypassed if strip coal oxidation kills the froth. Plant can be fed by belt from bulk storage, front end loader from storage piles and truck from the mines. Raw coal and each of four washed products can be fed by belts to three separate loading points on two separate railroads.

Jan 1, 1979

By B. Salopek

The greatest part of crushed stone, gravel and sand production is extracted through open pit operations, whereas gravel and sand are also partially extracted from riverbeds. Its obvious that such a mining activity provokes some changes in the configuration and environmental characteristics of the region, in the temporary or permament disapperance of vegetable or animal species and in the creation of noise, dust and waste water. However, the above-mentioned mining operations shouldn not have only negative effects on the landscape and land potential, but they can discover and predetermine the potential of the exploited areas for various communal purposes after exploitation (eg. sports and recreation centers, campsites, resorts, fish-farms, etc.). In this paper, the production of construction aggregates in plants located in the vicinity of Zagreb, the capital of Croatia is presented. The advantages and disadvantages of aggregates? production in urban areas in the spirit of sustainable development are discussed.

Jan 1, 2003

By A. G. Kim

Increasing transportation costs, clean air regulations and the decreasing availability of landfill space are factors in the increased interest in the utilization of low cost disposal sites for coal combustion residues (CCR). Inactive surface and underground coal mines can satisfy the conditions for stable CCR disposal sites, and subsurface CCR injection can be beneficial in reducing the amount of acid mine drainage (AMD) often produced at such sites. The material is expected to add alkalinity to the subsurface environment and to decrease the permeability and porosity of the buried spoil. Both mechanisms can reduce the amount of acid normally generated at a mine site. The Bureau of Mines is cooperating with an independent coal company in a test of subsurface injection of a mixture of fly ash, from conventional power plants or from fluidized bed combustion (FBC) , with AMD sludge into a reclaimed surface mine. Changes in water quality parameters and the concentration of heavy metals in water samples from wells and seeps are being used to assess the effect of CCR injection. The preliminary results discussed here indicate that improvement in subsurface water quality was related to fly ash injection and that components of the fly ash were stable in the acid environment.

Jan 1, 1994

By F. Vallianatos

The main objective of the present investigation is to demonstrate the potential of ERT (Electrical Resistivity Tomography) and HVSR (Horizontal to Vertical Spectral Ratio) methods as geophysical tools for the monitoring of subsurface cavities. The survey sites are located in Akrotirion Peninsula, almost 7 km east of Hania town in Crete Island, Greece. At this site, the surface expression of a known cavity with a diameter of about 25 m is visible. The true geometrical characteristics of the cavity were unknown since there are no boreholes in the area. The focus of this survey was primarily of a qualitative nature and the objective was to determine if ERT and HVSR could be used to identify and map near surface cavities (less than 30 meter in depth) in a limestones kartsic area such as Akrotirion Peninsula. A 2D/3D model of the resistivity distribution is given for the area under investigation. Furthermore, analysis of microtremors data provides a profile of the seismic response of the tectono-karstic voids.

Jan 1, 2006

By R. A. Hill

A brief explanation of the theoretical functioning of a regenerative system followed by its application to firstly, shuttlecars and then continuous miners and its effect on performance thereof with regard to handling, production and safety.

Jan 1, 1986

By Enrique Fernandez

The success of the excavation of a sewage tunnel in a very extreme geological conditions, from river deposits and sandy layers to hard dolomite, and several meters below the estuary under the sea water influence, shows that the choice of a right equipment together with the use of chemical products like foam and polymers enable to dig tunnels in unexpected areas and give solution to the environmental problems. The paper describes the excavation and support process as well as the adopted solutions in every material and during the cross through the intermediate shafts, also under sea influence.

Jan 1, 2003

By Ramkrishna Agarwal

A low grade iron ore is mined underground at Grace Mine using the panel caving method. Most of the development work is located in footwall. The runways for LHD equipments are heavily supported with steel sets on five foot centers. The sets are embedded in two to three feet of concrete. The initial cost of support is one of the largest single costs of production. During the process of ore-win¬ning, supports frequently fail, necessitating expensive repair. There is no systematic pattern to the failure of supports. A rock mechanics program was launched to isolate causes and their relative contributions to the failure of supports. The preliminary results are presented. A typical portion of a runway is instrumented to monitor rock mass movements around the runway and the corresponding response of supports as various mining activities are carried out in the neighborhood. We believe that such a program is a prerequisite to any remedial measure to alleviate pressure problem at Grace Mine.

Jan 1, 1973

By William M. Phillips

This paper will concern the processing of kaolin clays from the sedimentary deposits of Georgia and South Carolina, While the major processing steps will be touched on briefly, emphasis will be given to the dewatering of the clay-water slurries (slips) formed in the processing of kaolin clays The dewatering steps discussed will include gravity settling, centrifugal dewatering, vacuum filtration, and thermal dryings Of these dewatering steps particular attention will be given to vacuum filtration and the variables affecting filtration of these kaolin clays.

Jan 1, 1962

By R. Jin

The hydrophobicity of six coals ranked from lignite to anthracite is studied through contact-angle measurements, bubble attachment-time measurements, FTIR spectroscopy, and Hallimond-tube flotation. The preliminary study shows that the hydrophobicity of coals can be told by the bubble attachment times of coals (a kinetic criterion) or by the contact angles (an - equilibrium criterion). A general agreement between flotation response of coals and measured bubble attachment times or contact angles is observed in the present study. However, the study also shows that the hydrophobicity of coals can be predicted by FTIR spectroscopy work with proper manipulation of the spectra. Both hydroxyl and carboxyl groups in the coals are proven by FTIR work to be responsible for the change of coal hydrophobicity. A new criterion for the hydrophilicity index of coals from FTIR spectra is introduced through the study.

Jan 1, 1987

By C. A. Rowland

Autogenous grinding, defined as grinding with like material, while quite an old art has recently been revitalized. Two phases of autogenous grinding, primary and secondary, have been the subject of recent papers, technical articles and discussions. The purpose of this paper is to discuss a third phase of autogenous grinding - Intermediate Autogenous Grinding - comparing it to and indicating advantages over the other two phases. Autogenous grinding can also be called ?Rock grinding?1; that is, grinding using ore or rock from the same deposit as the mill feed as grinding media contrasted with using as grinding media steel rods, steel or ironballs, natural or manufactured iron, free pebbles, or other shapes and materials foreign to the mill feed.

Jan 1, 1964

By O. R. Swendseid

The Mountain Con mine is a relatively old, deep mine located in Butte, Montana. Operations at this property through the present shaft were started before the turn of the century. As mining progressed to depth, increasing demand for ventilation facilities and changing mining conditions made it convenient to convert some nearby shafts to airways. The fact that these openings had not been originally planned for use as airways made it necessary in some instances to utilize long and inefficient already-estab¬lished entries to service working areas. This situation existed in the Lexington fresh air system. The Lexington system consists of a vertical, 3-compartment shaft extending from surface to the 3200 level and a series of 2-compartment air raises and old horizontal-haulage openings extending into a mining area several thousand feet west of the Lexington shaft between the 3900 level and the 4200 level. Because of restrictions and high resistance in the portion of the system between the bottom of the Lexington shaft on the 3200 and the mining area on the 3900, the capacity of this system is only 85,000 cubic feet of air per minute. It was calculated that the capacity of the system could be in¬creased to meet the demands of the current mining program in this section of the mine by utilizing a single, straight, horizontal air course on the 3200 and by driving an inclined air raise 740 feet long between the 3900 and the 3200.

Jan 1, 1967

By Makoto Terada

The most important consideration in planning the plugging and sealing of a mine for mine water control is to predict the water flow from the mine. For this purpose, a method of numerical analysis on the water behavior in the ground at the concerned mine area was developed and the mine water flows were simulated. A hydrological survey at the surface of the mine determined the recharge rate of ground- water and the apparent permeability of ground.

Jan 1, 1982

By Ron Robinson

Booster fans have been in regular use in British coal mines since the first half of this century, but a large increase in their use did not take place until after the Nationalization of coal mines in 1947. From that time the need was identified to improve standards of ventilation in general and mining engineers specializing in ventilation were appointed at all levels in the mining industry. A comprehensive approach to ventilation surveys and planning, together with the realisation of the benefits of booster fans, led to their more rapid introduction. Many coal mines in the U.K. are at moderate depth and have virgin strata temperatures of 30°C or less. The ability to control climatic conditions by increased ventilation rather than resort to cooling systems has led to the introduction of booster fans and recirculation systems in these mines. Large makes of methane and high levels of coal dust production due to increased mechanization have also required enhanced ventilation standards. This paper deals with the reasons for selecting booster fans and the specific safety considerations involved in their use. Numbers, types and sizes of booster fans in the U.K. are outlined, together with notes on installation and performance. Remote monitoring and control from the surface is dealt with, and current legislation. The evolution of controlled recirculation is also covered starting with auxiliary fan systems in 1970 and leading to very large district schemes in the late 1980s. The research at Newcastle upon Tyne University and other establishments in the climatic conditions associated with recirculation is summarised and its use in assisting existing and proposed conventional and recirculation systems is indicated.

Jan 1, 1989

By Mehmet Guney

[The Atlantis-II-Deep is a hydrothermal mineralization located along the median valley of the Red Sea at a water depth of about 2200 m. Extensive exploration of the metal-rich brine deep revealed a potentially mineable deposit on economic interest consisting of oxides, silicates and sulphides with considerable concentrations of zinc, copper, cadmium and silver. Geostatistics was applied to assess the most likely in-situ vague of the metal potential for economical exploitation. Semi-variograms were constructed to characterize the structure of the regionalized distribution of the geological parameters. Volume grades and thicknesses were determined by the kriging technique, avoiding systematically biased high or low grades, and then block .tonnages were computed. The estimation variances, distribution of errors and histograms of observed and kriged values in each grid Mock were also produced.]

Jan 1, 1983

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for all concerned people. The coal industry has taken great measures to reduce both types of pollution. Through the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. In many cases, the complete elimination of thermal drying by using centrifugal dryers to dewater fine coal products and meet customer specifications has completely eliminated air pollution from this source. To help eliminate stream pollution and the hazards created by tailing ponds, the coal industry is using centrifugal dewatering equipment. Use of centrifugals to dewater fine refuse for disposal would eliminate refuse ponds or extend their life. In doing this effectively and economically, preparation plants have the option of recycling the clarified water to close the water circuit or of discharging the water into receiving streams with the assurance that it contains an acceptable amount of refuse solids.

Jan 1, 1974

By Jorgen Elbrond

In a stream of ore in an underground mine or in a beneficiation plant bins are installed between machines or machine system. When the upstream machine is stopped the downstream machine can continue operation for a while and vice versa. The paper describes a procedure for calculating the total capacity of a system consisting of two machines with an intermediary bin as a function of the bin's live volume and of the installed machine capacities and their production variations, which are defined. Extensions to several machines in parallel and in series are shown as well as practical examples.

Jan 1, 1982

By . A. J. Erickson

The Park City District, one of three major mining districts in Utah, is located approximately 20 miles southeast of Salt Lake City on the eastern slope of the Wasatch Mountains. The district has been in near continuous production since 1869. Production has been sustained from exceptionally long bedded replacement ore bodies in the Thaynes, Park City, and Humbug formations and also from several major veins. District production is summarized below. TABLE NO. 1 Park City District, Total Production, 1869 thru 1968 (Source r Various Company Records) [ ]

Jan 1, 1970

By E. Kurt

The field of percussion rock drilling is subdivided into two areas of application; that which takes place on the surface and that which takes place underground. Surface drills are used in quarrying, highway construction, and maintenance work; underground equipment in mining and tunneling work. Two basic principles are involved in the operation of all percussion drills. First, the principle that reciprocates the impacting piston and second, the principle that causes the drill steel and bit to rotate. The back and forth motion of the piston is accomplished by a self-acting automatic valve that admits air alternately to each end of the piston (Figure 1). Drill steel and bit rotation is imparted by an integral ratchet mechanism (Figure 2) in the so-called "rifle bar" machines (Figure 1) or by a separate pneumatic motor in "independent rotation" drills (Figure 3). While rock drills are subject to all kinds of physical and operational abuse, they are most sensitive to faulty lubrication. Proper lubrication is the single most important factor in the longevity of a percussion drill.

Jan 1, 1970

By M. R. Lastra

Island Copper Mine began gold recovery Tom molybdenum sulfide concentrates in April, 1985. Plant design capacity is 20 tons of molybdenum concentrate per day. The molybdenum concentrate is produced in a conventional copper/molybdenum flotation circuit by selective copper depression. After thickening, the molybdenum concentrate is leached with cyanide solution in a series of five leaching tanks. The leached concentrate is then filtered and soluble gold values recovered on activated carbon with a six column adsorption circuit. The gold leach extraction is approximately 80 percent with a gold adsorption on activated carbon of 97 percent.

Jan 1, 1986

By J. W. T. Ropkins, D. Allenby

The paper describes a technique by which large concrete boxes are unobtrusively inserted beneath existing highway and railway infrastructure to form new subways, culverts and under-bridges, thus avoiding the inconvenience and costs of disruption to traffic associated with traditional cut and cover techniques. A series of project examples, undertaken in the United Kingdom and United States, are used to illustrate the design and construction of the box structures, together with the technology required to control ground disturbance in the tunnel face and around the box, and the jacking systems necessary for box installation.

Jan 1, 2003