Search Documents

By Huimin Lu, Lian Zhou, Qiang Li

"A three-dimensional mathematical model is developed for the regenerative rotary hearth furnace with 40 meters medium diameter. The influence of combustion switchover and outlet pressure on the fluctuation and distribution of temperature and pressure is studied with numerical simulation method. The results showed that the temperature field and flow field is suitable for requirement of industrial production; the fluctuation of the temperature field and pressure is acceptable; the influence of outlet pressure on the furnace pressure is great.IntroduceRotary hearth furnace which is originally utilized as heat treating and reheating industrial furnace, now is also used for carbon based DRl production. With the need of market and the concern of resource recycling and environmental issues, the DRl production from ore or from waste material by rotary hearth furnace attracts more and more attentions from steel industry [1,2].When rotary hearth furnace works, the feed pellets are charged on the hearth and rotate within an annular furnace chamber with the process of reduction. For the sake of rapid reduction, usually the depth of the pellet is one or two layers, accounting for less than 90% of the volume of furnace. As result, the exhaust gases carry away a lot of heat, so that energy utilization efficient is low [3]. Currently, in order to reduce the consumption of energy and improve the production efficiency, many methods have been adopted. The regenerative combustion technology is one of the most promising."

Jan 1, 2013

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By John A. S. Green, J. Gilbert Kaufman, Subodh K. Das

"The aluminum industry is a leading proponent of global sustainability and strongly advocates the use of recycled metal. As the North American primary aluminum industry continues to move offshore to other geographic areas, such as Iceland and the Middle East, where energy is more readily available at lower cost, the importance of the secondary (i.e., recycled metal) market in the U.S. will continue to increase. In the past, the recycling industry had been synonymous with the collection of aluminum beverage cans. However, as the opportunities for aluminum recycling have multiplied in motor vehicles, building and construction, and aerospace, these market are getting additional scrutiny for optimization of recycling strategies.Accordingly, the secondary industry can now draw upon a much wider range of product forms and alloys for its raw material, but this in turn brings issues of alloy sorting, impurity content, and control as the material is remelted and recycled into new product forms. The purpose of this paper is to take an integrated, industry-wide approach to look at the recovery of material from demolished buildings, shredded automobiles, and aging aircraft, as well as from traditional cans and other rigid containers. Attempts will be made to assess how the different alloys used in these separate markets can be recycled in the most energy efficient manner.IntroductionIn his recent book “Aluminum Recycling”[1], Mark Schlesinger points out that in traditional extractive metallurgy, the raw material used to produce a metal is mined from the earth and then is separated from other gangue minerals and impurities. In aluminum recycling, however, the ore body consists of scrap metal found on the ground, rather than in it. He further notes that scrap comes with its own variety of gangue and impurities such as painted coatings, other metal attachments, and even dirt and other contaminants. So, while the recycling process still requires some refinement and expenditure of energy, the effort and energy involved is much less than traditional mining."

Jan 1, 2008

By Ehsan Vahidi, Fereshteh Rashchi, Amirhossein Shahnazi

"The pig iron from steel manufacturing plants contains a high concentration of vanadium-bearing materials smelted with iron ore. During the oxidation process of the molten pig iron with oxygen lances, vanadium transfers to the slag. In this research, recovery of vanadium from LD (Linz-Donawitz) converter slag of steelmaking plant was investigated. The leaching residue was characterized by XRD and XRF techniques. The maximum vanadium recovery was achieved at optimum leaching conditions of 70 °C, S/L: 1/15, sodium hydroxide concentration: 3 M and leaching time: 150 minutes. The dissolution rate increased with rising sodium hydroxide concentration and temperature and decreasing particle size. The experimental data are treated graphically to explain the kinetics of the vanadium recovery process using shrinking core model (SCM). As a result, the controlling regimes in the SCM were analyzed separately using liquid film diffusion control, solid product diffusion control, and reaction control mechanisms.IntroductionVanadium is commercially important as a constituent of several alloys and catalysts. Nowadays, vanadium is mostly recovered as a by-product from secondary sources or from industrial waste streams such as titaniferrous magnetite, fly ash, spent catalysts, and petroleum coke. Steelmaking operations are specifically concerned by this problem due to the production of a huge quantity of by-products [1]. These by-products, including LD converter slag, sludge, fly ash, spent catalyst, ash, and alloyed scrap, contain a notable amount of heavy metals which may cause environmental problems. Solvent extraction is one of the techniques being increasingly used for the recovery of vanadium [2]. Apart from vanadium ore, secondary resources such as titanmagnetite, ilmenite and slag from the ferrous industry are a major source of supply. The pig iron from steel manufacturing contains a majority of vanadium-bearing materials smelted with iron ore. In a heat resistant shaking ladle the molten pig iron is oxidized with oxygen lances, causing the vanadium to be transferred to the slag. Normally, the vanadium in LD converter steel slag (coming from Linz-Donawitz steelmaking process) is ca. 5% as vanadium pentoxide (V2O5). This slag is the world's principal raw material for vanadium production [3, 4]. Moskalyk and Alfantazi [4] reported that a roast-leach process is used in South Africa for the production of vanadium oxides from magnetite ores while some of the slag was converted to ferrovanadium. A portion of the slag was exported to Europe for the production of vanadium oxide. The researchers mentioned that alkaline roasting was the main process at that time employed to extract vanadium pentoxide from vanadium slags."

Jan 1, 2012

By M. H. Ghandehari

Sintered (Pr,Sm)Co5 displays a multi-phase microstructure in which closely related intermetallic compounds are formed during the process of fabricating useful magnets from over-stoichiornetric compositions. These compounds have much lower magnetic crystalline anisotropies compared to those of SmCo5 and PrCo5. Despite a careful control of the microstructure in producing "single phase" PrCo5 base magnets, sufficient concentrations of the lower anisotropy phases are formed which act as nucleation centers for domain reversal, resulting in a drop in coercivity. This article describes the use of sintering additives, primarily oxides, to prevent the formation of the magnetically soft phases in the final microstructure.

Jan 1, 1989

By U. Lauwers

The influence of different waste materials in sinter blends on the quality and mineralogical composition of a sinter is described. As a result of partial preservation of the original textures of waste materials in the final product the degree of assimilation of the original material in the sinter product can be ascertained. Recycling of waste materials such as dolo char , arc-furnace slag, scrap fmes, mill scale and BOF-mud via the sintering process a saving on costs of raw materials such as flux and fuels, and a reduction on pollution can be achieved. A comparison of a typical sinter with a sinter produced through the utilization of waste materials showed a distinct correlation between certain types of waste material and some metallurgical properties. Dolochar in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. Generally dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter. The glass and calcium ferrite content of a sinter when dolochar is used in the blend is similar to that of a sinter produced with only coke as a fuel in the sinter mix. The glass content is lower and the calcium ferrite content is higher, in a sinter produced from dolo char in the blend compared to a sinter produced with additions of other waste materials. Changes in the mineralogical composition are related directly to the metallurgical properties of the sinter product.

Jan 1, 1991

By Min Chen, Lei Xu, Liang-yu Jin, Xue-liang Yin

For the purpose to reduce the high cost and heat storage loss of Al2O3-MgO bricks used as ladle linings, Al2O3-MgO-CaO bricks with lower theoretical density were fabricated and the densification behavior as well as mechanical property of this refractory was investigated. With addition of CaO, the initial sintering temperature of Al2O3-MgO refractory was decreased from 1300 to 1100°C associated with the expansive formation of CA2, and the compressive strength was also enhanced owing to the formation of bond linkage between CA6 and spinel. At high temperature, brick with 4% CaO content showed poor sinterability with high porosity because of the formation of platelet structure of CA6 grains, whereas brick with 8% CaO content was well sintered with higher relative density but lower bulk density than Al2O3-MgO brick, indicating that the densification as well as lightweight of Al2O3-MgO refractory was effectively promoted.

Jan 1, 2015

By Dong Liu, Zejian Yang, Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"The structure, composition, morphology, and adsorption property of UV-vis light of as-prepared samples were characterized using XRD, SEM, FTIR-EDS, and UV-vis DRS. UV-visible light induced photocatalytic degradation of methylene blue ~) over Ti02-doped diopside was investigated. Experimental results show that doping Fe + induced the formation of Ti-0 or Ti-0-Si in diopside, and promoted the light adsorption property of diopside. Photocatalytic reactivity of Ti02-doped diopside obviously depended on content of doping Ti02. The diopside with 3% Ti02 exhibited the superior photocatalytic activity with 76% degradation of methylene blue under light irradiation for 3 h.IntroductionPhotocatalytic technology has been extensively studied in the process of dealing with inorganic and organic pollutants. Ti02, with its own non-toxic, stable, low-cost and other advantages, has become the most widely studied photocatalytic materials[l-SJ_ The low utilization quantum made it restricted in the practical application. SrTi03 as the representative of the perovskite[9·121, Bi2W06 for the composite oxide[13,141, also attracted wide interest in the photocatalytic studies. However, these photocatalytic material has been mostly prepared in relatively strict experimental conditions with chemical reagents, they had small production, high cost, which made them difficult for practical applications.In our country, there has 400 million tonnes of ti-bearing blast furnace slag (TBBFS) each year in the process of smelting pig iron, which has lead to waste of titanium resources and pollution of the surrounding environment. In recent years, studies have shown that TBBFS instead of pure Ti02 to be photocatalytic materials is feasible[ 151. TBBFS has not only been higher photocatalytic degradation activity for the o-nitrophenol, methyl orange, nitrobenzene and other organic matter[16-191,but also exhibited excellent in the process of dealing with inorganic heavy metals in waste water (containing Cr6+i201. If TBBFS can be successfully applied to photocatalytic technology, the will make large accumulation of titanium-bearing slag reasonable used, so as promote the re-use of energy. At present, our understanding of the photocatalytic activity of TBBFS is steadily deepening. Photocatalytic activity ofCaTi03 has been reported as one of the main minerals ofTBBFS [21'21J, However, there were few studies for Another major mineral of TBBFS - diopside which had the content of9-15%. diopside would doped with Ti02 In the process of smelting pig iron, therefore, Ti02-doped diopside's photocatalytic activity in the UV-Vis was mainly studied in this paper."

Jan 1, 2013

By SenYang Qian, ShuangYu Du, Bo Wang, Jieyu Zhang, Jian Zhao

During the solidification process, the flow pattern of the molten steel has significant influence on the formation of solidification microstructure. In present study, the solidification microstructure of 30Cr2Ni4MoV steel ingot under different intensities of mechanical oscillation(forced convection) was simulated by using ProCAST®software. The results showed that the increase of the intensity of oscillation could restrain the development of the columnar grains and refine the grains. As the intensity of oscillation increased, the proportion of columnar grains decreased and the proportion of equiaxed grains increased. When the intensity of oscillation was at a low level, the effect of refining grains could be improved obviously by increasing the intensity. However, as the intensity increased to over 0.833, the effect of refining grains would not be improved.

Jan 1, 2016

By Qingyu Deng, Shiwei Ma, Guibao Qiu, Hua Wang

"The flow behavior of the blast furnace slag bearing titanium, like viscosity, play an importance role during the iron-making process with the vanadium-titanium magnetite, which is a very special minerals in Panzhihua, China. The dependency of the viscosity on the chemical composition like TiO2, Al2O3, MgO, binary basicity (CaO/SiO2), temperature, reaction time were studied. The experiments showed that the viscosity decreased with the increase of TiO2, MgO content and binary basicity, and it increased with the increase of Al2O3 content and temperature. The viscosity showed a slight decrease within 60mins’ reaction with graphite crucible, however, it increased rapidly afterwards with the formation of Ti(C, N).IntroductionThe ordinary iron ore has been an essential part of raw materials for vanadium-titanium magnetite smelting in Panzhihua to avoid a series of problems, such as slag thickening, adhesive bond of slag and hot metal, etc. The ratio of vanadium-titanium magnetite has been decreased gradually since 1970s, and has down to about 65% now. However, with the substantial appreciation of price of imported ordinary iron ore, Panzhihua Iron and Steel Group aims to increase the ratio of vanadium-titanium magnetite and decrease the dependence on ordinary iron ore in order to lower the cost of smelting process."

Jan 1, 2012

"The pyrometallurgical method of recycling car batteries suffers from a potential for air pollution violations, which prompts the desire for a viable hydrometallurgicaJ alternative. Several Processes have been proposed, including leach-electrowinning routes using HBF4 and/or HzSiF6 based electrolytes, along with anodes of PbO2 on inert substrates.A study has been carried out to evaluate the proposed systems, with the intention of demonstrating a six month life of an electrolyte-anode combination. The work, which focused on the use of HzSiF6, has indicated that there was no acceptable anode, and has lead to the development of a technique to produce smooth, glassy, adherent coatings on graphite, and to the development of an anode composed of a series of copper cored graphite rods.The paper will present results on leaching and electrowinning experiments, as well as the description of a flowsheet for a pilot plant that will be used to produce one tone per day of refined lead from spent battery paste."

Jan 1, 1997

By O. Morfín

The most probable source of Pb contamination in the perennial reach of Aravaipa Creek, Arizona, has been determined using Pb isotope ratios and total metals analyses of samples collected from the ephemeral and perennial reaches and mine wastes located in the Aravaipa Mining District . Previously, elevated levels of Pb, Cd and As in fish in the perennial reach of Aravaipa Creek, a protected wilderness area,, were assumed to be due to off-site transport from abandoned flotation tailings piles located at Klondyke, Arizona upstream of the wilderness area.Our work replaces this inference with isotopic data that allows us to confirm this hypothesis. The Pb/Zn deposits of the district were mined between the late 1890s and the late1960s, with the most significant ore production coming from one deposit in a rhyolite dike swarm on the Western front of the Santa Teresa Mountains, a granitic pluton of Cretaceous-Tertiary age (~65 ma). Mineralogy has been well constrained across the length of the lode system: Pb and Zn sulfides predominate in the NW sector, and a mixed suite of hypogene/supergene Pb sulfide and Pb oxide minerals comprises the majority of its SE corner. Total metals analyses and comparison of metals ratios serve to constrain the source and transport of certain metals within different parts of the system. Pb isotope ratios in samples, obtained by ICP-MS analysis, define two distinct contributors. The first end-member (208Pb/204Pb = 38.513 to 38.721 and 207Pb/204Pb= 15.550 to 15.598) is characteristic of the mixed, oxide/sulfide ores at the SE end of the deposit. A second end-member (208Pb/204Pb = 38.855 to 38.946 and 207Pb/204Pb = 15.610 to 15.625) characterizes samples taken from the NW, purely Pb sulfide end of the lode. Pb isotope ratios from perennial reach sediments are closely correlated with ratios given by samples from the Klondyke tailings site and by Pb sulfide samples from the NW sector, the primary source of ores processed at Klondyke.

Jan 1, 2003

By Xin Zhang, Xu Zhang, Hao Bai, Ning Li

Organic Rankine Cycle (ORC) is an effective technology for low-grade waste heat power generation. In this paper, the thermal-dynamic performance of ORC system, in which low-temperature waste heat (from 40-140oC) is used as heat source, was evaluated with software RefProp8.0. The result indicates that in the range of low temperature, the working fluids like R601, R601a, R600a, R141b, R245fa and R245ca have better thermal performance. Furthermore, pilot-scale experiment using R245fa as working fluid was conducted, which validated the operation of the system for low-grade waste heat recovery. Finally, the economic feasibility of ORC has been analyzed for an ORC system using the waste heat from quenching water of blast furnace slag (80oC). According to the analysis, the project is reasonable in economy because the recovery period of investment is less than 4.2 years and environment-friendly since the CO2 emissions can be reduced by almost 43650.68t annually.

Jan 1, 2016

By Jaeheon Lee

Gold-copper alloys are shown to form during the cementation of gold on copper in a solution containing 0.25M [S2O32-] at 25oC. The alloy composition is strongly dependent on the initial Cu:Au ratio in solution and ranges from Au3Cu to AuCu3. XPS results for Au, Cu, S, and O are reported as a function of depth through an entire deposited film with an initial solution containing 20 ppm [Au] and 30 ppm [Cu]. The deposit contained about 20 atomic % gold and was predominantly Cu3Au. Underpotential deposition (UPD) theory is discussed as a mechanism for explaining the formation of these alloys. Several other systems that produce alloys during contact reduction/cementation are also discussed.

Jan 1, 2003

By Gerson de Araújo Filho

This paper shows the use of tires as fuel to be employed into blast furnaces. The tires can substitute coal or even charcoal in the blast furnaces tuyeres. The injection into tuyeres, besides the contribution for energy generation, can also produce gas for iron oxide reduction. The tires, as powder to be injected into blast furnaces, contributes for an environmental use of this waste, which helps to obtain a high value product as well. So, the advantage of using such material is that it is waste and has lower cost for preparation. The obtained results showed that the tires have good combustibility. This one was obtained in a model that simulates the same conditions occurring in the blast furnaces tuyeres; these used raw materiais include tires and mixtures of tires with coal or even with charcoal.

Jan 1, 2006

By K. Yarnaguchi

In the Mitsubishi Continuous Copper Converting Furnace, calcium femte slag is used. Due to its extremely high basicity, the improvement of corrosion resistance of the refractory lining is in need. In order to clarify the corrosion mechanism and to search for a new corrosion resistant material, first, the surface snuctures of bricks corroded in molten slags were observed by EPMA. Second, the dissolution behaviors of sintered MgO-based pellets containing various oxide additives were examined. It was found that the formation and the dissolution of magnesiofemte at the surface of the bricks play an important role in their corrosion and an addition of NiO, Mn02, or Ti02 to MgO is effective in stabilizing the magnesio-femte and improving the corrosion resistance of MgO.

Jan 1, 1994

By Yanhui Liu, Xuewei Lv, Pingsheng Lai, Chenguang Bai

The purpose of this paper is to study the effect of slag basicity on the Si content in stainless steel master alloys prepared by smelting reduction of Fe-Ni-Cr sinters. Theoretical analysis focusing on the gas, slag and alloy phases of the smelting reduction process at 1600°C was carried out by thermodynamic calculation software----FactSage, showing that the increase of CaO within the slag can result in the decrease of Si within the master alloy. Experiments were also carried out in vacuum melting furnace at 1600°C , and chemical analysis method was used to detect Si content in the alloys. When the MgO content is 9.00%, the experimental results were consistent with the calculated values. However, when the MgO content rises up to 14%, the content of Si in the alloy reaches the maximum when SiO2 equals to 22.81%.

Jan 1, 2016

By Vojteh Leskov?ek

The tribological load is the load on forging tools resulting from the relative motions between the plastically deformed workpiece and the die. In comparison to many other forming processes hot die forging has an especially disadvantageous tribological system. The advantages of the application of hard coatings, which are well known for cutting tools, are to a much lesser extent explored for casting, extrusion, molding and forging tools. Increasing the lifetime of these tools is an important task in surface engineering because of the complex loading conditions and often complicated tool geometry. The plasma-assisted chemical-vapor-deposition (PACVD) technique is well suited to depositing hard coatings onto large dies and molds. The aim of this study is to present and discus results obtained on a duplex PACVD hard coating in an industrial application like the hot forging of automotive parts. A new generation of vacuum-melted and remelted (VMR) hot-work tool steels has been developed; these can reach a hardness of 58 HRc, and have a fracture toughness at this hardness equivalent to that of standard hot-work tool steels at 45 HRc. This offers one of two advantages: the steels can be used at the higher hardness to provide resistance to wear or deformation, or, when used at a hardness of 47?49 HRc for hot forging, to provide temper resistance, nitriding behavior and adhesive wear resistance. The results presented here are from a preliminary investigation. The experimental results indicate that the introduction of a proper duplex PACVD hard coating will lead to an improved wear resistance and a longer lifetime for the hot-forging dies. Furthermore, by using a hard, low-friction coating excellent anti-sticking properties can be obtained. At this stage of the investigation it is also necessary to carry out pilot trials to determine the wear resistance and the tool life in practice.

Jan 1, 2006

By Dhanesh Chandra

Long term stability studies were conducted on four variants of LaNi5; 10,000 hydriding/dehydriding cycles were used to evaluate their suitability for a metal hydride cooling system. Thermodynamic and structural studies were conducted to determine changes in these materials during cycling test period. The hydrogen sorption properties of LaNi5.2, and Lao 9Gd0.1Ni5 and LaNi4.75In0.27 were seriously degraded during the tests but the LaNi4.8Sn0.22 hydride was virtually unaffected. Hydride isotherms were measured at the beginning and at intervals through out the test period to observe the nature and extent of damage degradation in the sorption properties. X-ray diffraction studies of the alloys (LaNi5.2, LaO.9Gd0.1Ni5 LaNi4 8Sn0.22) and their respective hydride, before and after test, provided insight with regards to the observed changes in the hydride properties. Electron microscopic studies were also conducted to evaluate the changes in particle sizes.

Jan 1, 1989

By Wantae Kim, Jaechun Lee, Tatsuya Oki, Sungbaek Cho, Sangbae Kim

"Effect of attrition scrubbing on the recovery of platinum group metals(PGMs) from automotive catalytic converter was discussed. The attrition scrubbing as comminution and separation process was effective for the recovery of the catalyst layer, ?-alumina, from ceramic supporting matrix, cordierite, by physical impact and shearing action between particles in the scrubbing vessel. The catalyst layer was dislodged from the surface of the supporting matrix into fine particles less than 45µm by attrition scrubbing. The production of fine fraction less than 45µm increased as the residence time for attrition scrubbing increased. The fine fraction obtained at the residence time of 40min contained 19.25% CeO2, 1.93% ZrO2 and 418.8ppp PGMs. The recovery of ?-alumina in the fine fraction increased as the residence time increased. Simultaneously, the recoveries of CeO2, ZrO2 and PGMs increased and reached up to 82.9% CeO2, 78.7% ZrO2 and 78.9% PGMs at the attrition scrubbing time of 40min. The production of the fine fraction and recovery of ?- alumina increased when the solid concentration and initial feed size increased.IntroductionThe automobile catalytic converters contain appreciable amount of PGMs. Currently several million tons of used catalytic converters are disposed annually worldwide, each containing about 0.5-1g of platinum and 1-2g of all PGMs1). The recovery technologies of PGMs from spent catalytic converters have been thoroughly reviewed by numerous researchers since last decades. Two types of methods, wet and dry processes, have been commercially operated. In the wet process, the PGMs on the spent catalytic converters were dissolved mostly in the form of chlorocomplex, MCl6 2-, by contacting with aqueous solutions. Subsequently the resulting solutions are treated to concentrate and the precious metal ions are reduced by introducing metals such as Al, Fe and Zn in the concentrated system2). In the dry process, the spent catalytic converters are melted, in some case with CaO, at an elevated temperature to produce a low viscous slag. The PGMs in the melt are separated by allowing them to adsorb on Fe or Cu having high specific gravity7). Although highly pure precious metals could be obtainable, the recovery technologies of PGMs currently operated seem not to be cost-effective since PGMs embedded in these types of catalytic converters are present in very small quantities."

Jan 1, 2008