Search Documents

By T. H. Courtney, B. R. Murphy

"Nominal room temperature mechanical alloying (MA) has been used to synthesize the high melting temperature NbC and Cu-NbC composites. Elemental powders of Cu and Nb were alloyed in the presence of either graphite or hexane to form nanocrystalline NbC or a Cu-NbC composite. Through control of hot-isostatic-pressing (H/Ping) parameters, we have been able to minimize microstructural coarsening during densijication, and have processed fully dense bulk compacts of both single phase NbC and two-phase Cu-NbC while maintaining a nanocrystalline or near-nanocrystalline structure. These materials generally exhibit high strength and low fracture toughness. However, mechanical properties vary significantly depending upon the Cu content and the method of NbC synthesis (graphite or hexane).INTRODUCTIONMechanical alloying (MA) has been recently used to synthesize a variety of inorganic solids; sulfides (1-2), nitrides (3), borides (4), and carbides (3, 5-8). One advantage of this processing route is that synthesis of fairly high melting temperature materials takes place at what is nominally room temperature. Another advantage is that the structures generated are often nanocrystalline in scale, with attendant interesting properties. The consolidation of these fine structures into near fully dense or fully dense materials while limiting microstructural coarsening is a challenge that has just recently seen limited success (5, 9). We report here on some recent studies of ours dealing with crystallite size and structural analysis of NbC and CuNbC composites consolidated to full density from mechanically alloyed powders. Bulk mechanical properties and their dependence on milling parameters are also presented."

Jan 1, 1994

By C. M. Iheagwara

An overview of the scope and ramifications of scrap recycling in the Nigerian metallurgical industries has been presented in this paper. The modern state-of-the-art processing techniques and the operational strategies employed in the recycling plants are discussed. Optimization techniques for cost effective recycling operations are highlighted. As new units within existing metallurgical plants and new metal working plants approach commercial operations, expansion of existing recycling plants and the emergence of new ones have been showing to hold the key to their profitability from the raw material standpoint. The present economic predicament of the entire industrial sub-sector, lack of sufficient foreign exchange to procure new machineries and the emergence of a maintenance culture have triggered a phenomenal increase in the number of spin-off industries which depend on metal recycling activities. This, it is argued, widens the horizon for scrap processing/recycling.

Jan 1, 1992

By Hans Jürgen Maier, Hans-Bernward Besserer, Gregory Gerstein, Florian Nürnberger

The formation and development of voids in both the single-phase ferritic steel DC04 and the dual-phase ferritic-martensitic steel DP600 are discussed. Various mechanisms and kinetics of void formation are considered regarding the influence of dislocation glide, precipitates and other parameters. Different characteristic locations in the microstructure are investigated at which strain concentrations during plastic deformation can occur and cause the formation of voids and microcracks. For the specimen preparation ion slope cutting is applied. Voids and cracks revealing ductile damage are analyzed by Scanning Electron Microscopy (SEM). Stress concentrations in consequence of plastic deformation could be shown by extinction contours on images recorded by Transmission Electron Microscopy (TEM).

Jan 1, 2015

By Peter G. Cooper

"During 1987, the feasibility of modernising the ER&S smelter at Port Kembla, NSW, Australia was studied. The selection of appropriate technologies to carry the smelter into the 21st century considered issues such as capital cost, existing infrastructure, feed mix, capacity, product quality, flexibility and potential for further development. Both hydrometallurgical and pyrometallurgical process schemes were considered. Some novel combinations were assessed but ultimately rejected. Final technology selections included proven smelting and anode furnace processes, pyrometallurgical slag cleaning and modifications to existing equipment. This process scheme balanced risk against development potential within the constraints imposed by the existing plant.BackgroundThe Electrolytic Refining and Smelting Company of Australia (ER&S) has operated a custom copper smelter at Port Kembla since 1908. Existing technology includes a sinter plant/blast furnace, three small Peirce Smith converters, two reverberatory anode furnaces and a conventional tankhouse. These process units were all installed prior to 1960 and have proven to be flexible enough to process the wide variety of domestic feed materials purchased by ER&S.However, by the early 1980s, threats to domestic concentrate supplies highlighted the need for major changes to reduce operating costs to world competitive levels. Various studies in the ensuing years failed to identify an economically attractive solution. Furthermore, pressures were increasing to improve the environmental performance of the smelter.During 1986 the options for redevelopment were again considered and by the end of 1987 technologies for the retrofit had been selected and a full feasibility study was completed."

Jan 1, 1988

By Sheng-li Wu, Guo-liang Zhang, Bo Su

The mineralogical characteristics of iron ores can influence their high temperature sintering performance. In this study, eight iron ore samples from Brazil, Australia, and South Africa were characterized by their chemical composition, mineral types, particle morphology, and gangue dispersity. Meanwhile the influence rules between the mineralogical characteristics and the high temperature characteristics were evaluated and analyzed. The results showed that the effect of SiO2 on assimilation characteristic of iron ores was relatively complex, Al2O3 and LOI of iron ores had negative correlation with assimilation temperature of iron ores, the dense slab-flaky mineral granule restrained to the assimilation characteristics of iron ores; liquid phase of iron ores with high SiO2 content and low Al2O3 content had high fluidity, and the higher dispersity of gangue minerals in iron ores was good to the fluidity of liquid phase.

Jan 1, 2015

By R. P. King

The essential features of an image analysis system for the measurement of mineral liberation are described. Good procedures for image acquisition and image processing prior to image analysis are defined. The basic stereological methods for the measurement of volume fraction, surface area per unit volume, particle size distribution and liberation spectra are given. The appropriate methods for fractal correction when measuring perimeters of irregular features and for frame correction when measuring linear intercepts are developed. Practically useful and accurate procedures for the stereological correction of particle size and liberation distribution methods are given.

Jan 1, 1995

By Hiroshi Tabuchi, Akihiko Takahashi

"High strength aluminum matrix composites were prepared and studied using as reinforcement newly developed nearly mono-dispersed a-alumina single crystal particles each of which has a regular polyhedral shape. The composites were formed by centrifugal casting using aluminum casting alloys (Al-Si and Al-Cu-Mg) as the matrices, followed by heat treatment. The volume fraction of the alumina particles was as high as 60%. The same matrix composites reinforced by conventional crushed fused alumina particles were similarly prepared as the reference. The bending strength and tensile strength of the Al-Cu-Mg matrix composites reinforced by the novel alumina particles of 10 µm in average diameter are as high as 1020 MPa and 560 MPa, respectively, which are higher than those of the conventional alumina composites. Furthermore, the bending strength of the novel alumina composites degraded less than that of the conventional alumina composites after thermal fatigue tests. The number of cracks in the matrix seemed to influence the thermal fatigue property because many cracks were observed in the conventional alumina composites, whereas only a few cracks were observed in the novel alumina composites. This was confirmed by SEM observation of the sample composites before and after the thermal fatigue tests.IntroductionAluminum matrix composites strengthened by dispersed reinforcements are of interest for various applications due to their improved properties, such as high specific strength and stiffness, wear resistance, etc .. A large number of investigations have been made concerning fabrication processes and properties of these composites. With regard to the fabrication processes, powder metallurgy has been well-known as a solid phase process, and recently many liquid phase processes such as a compocasting, a squeeze casting, the Lanxide process, and the Osprey process have been studied and developed.(1)"

Jan 1, 1998

By G. E. Lagos

This paper analyses the scope and instruments employed by the Basel Convention for regulating the transboundary movement of hazardous wastes, the present and projected hazardous waste regulations of Chile, reviews the Chilean import/export trade of wastes of the period 1985-1995, and discusses, the influence that the Basel Convention has had on mining trade, its perceived benefits and costs, and possible effects on Chile's trade of the application of the Convention's Decision III/l. There is no quantitative estimation as to the effect of the Convention on the general volume of imported or exported materials destined for recovery, recycling, reclamation, or reuse. All recycling imports, with the possible exception of residues of petroleum oil, which occurred during the decade 1985-1995, can be classified tentatively as non hazardous. The entry into force of the Convention has had several effects on Chile's trade. It has brought home the need to have a comprehensive hazardous waste legislation, it has been a base for applying import restrictions, which in all likelihood, would .have otherwise not been applied, The benefits and costs of this import restriction, as well as those of the multilateral export ban are analyzed.

Jan 1, 1999

By Xiang-dong XING, Zhen-yang wang, Jian-Liang Zhang

Distribution behavior of titanium between CaO-SiO2-MgO-Al2O3-TiO2 and hot metal was studied between 1350 °C to 1600 °C. Experimental results indicate that the reaction temperature influenced the activity coefficients of titanium and resulted in the variation of equilibrium constant. Finally, the Gibbs free energy formula of titanium carbothermic reduction was fit out using the thermodynamic model of Wagner and congregated electron phase models.

Jan 1, 2015

By Marc Liebman

We present the results of a telephone survey of electric arc furnace (EAF) steel producers. This report characterizes the current status of EAF dust generation, treatment and disposal. It indicates the quantity generated, zinc content, other relevant constituents, and plans and trends that will impact on the quantity and characteristics of the dust generated. The survey covers EAF based steel producers in the United States and Canada. It identifies the processors currently employed, opinions about the use of these processors and services, as well as new technologies being considered.

Jan 1, 2000

By Alessandro Blasi, Massimo Morgana, Corradino Sposato, Pietro Garzone, Giuseppe Devincenzis

A comparison among (2-ethylhexyl)-mono (2-ethylhexyl) ester Phosphonic acid (P507), Secondary-octyl phenoxy acetic acid (CA-12) and Bis(2,4,4-trimethylpentyl) phosphinic acid (Cyanex272), in heavy rare earths separation via hydrometallurgical processes has been investigated. The separation coefficients, , were obtained and the extraction selectivity has been evaluated using a mixture of heavy rare earths from Samarium to Ytterbium. The experimental results indicated that P507 and Cyanex 272 display a greater affinity for heavier rare earths while CA12 proved to be more effective for the lighter rare earth metals.

Jan 1, 2014

By Jae-Ho. Lee

For some electronic applications where a dispersed electrically-conductive particulate-phase is employed, the conductivity of the surface (or near-surface region) of the particles provides for the primary mechanism which determines its electrical conductivity. Particles of a less expensive material, which may have desirable thermal-expansion properties, when coated with silver offer a means of also obtaining desirable electrical properties and at low cost. The research conducted was focused primarily on the development of silver-coated tungsten particles for thick-film polymeric conductors. The ammoniacal electrolyte was formulated from silver-nitrate, glycine inhibitor and formaldehyde reductant. The reduction, and subsequent deposition, of silver occurred selectively on the surface of the tungsten particles. Coated particles were assessed by SEM imaging. The thickness of the silver coating was estimated to be approximately 100nm on the basis of a mass account and the coating being uniform. The electrical conductivity of a silver-coated tungsten-powder pellet was found to be similar to that of a silver-powder pellet, of identical geometry.

Jan 1, 1997

By Seyed Ahmad Jenabali-Jahromi

In this paper a meshless method called Finite Point Method (FPM) is developed to simulate the solidification process of continuously cast bloom steel in both primary and secondary cooling region. The method is based on the use of a weighted least-square interpolation procedure. A transverse slice of bloom as it moves with casting speed is considered as computational domain. The two dimensional heat transfer equation together with temperature dependent thermophysical properties is solved in the computational domain. The present work is verified in the mold region by the comparison of the surface temperature simulated by FPM and finite volume method (FVM) and also comparison of solidified shell thickness simulated by FPM and measured on a breakout bloom. For secondary cooling region the validation is done by comparison of the surface temperature simulated by FPM, FVM and thermovision measurements.

Jan 1, 2009

By Jun Sugiyama, Hiroyuki Sano, Toshiharu Fujisawa, Hideki Takeuchi, Chikabiuni Yamauchi

"The solid .state electrotransport (SSE) is one of the most promising methods for the elimination of gaseous impurities from chemically active metals, such as rare earth metals. . In the present work, the SSE process was applied for the oxygen removal from praseodymium. The SSE factors, such as effective valence, were measured under the various temperatures, electric field intensities and initial oxygen contents, and the effects of those conditions on the SSE process were discussed. Furthermore, the solubility of oxygen in .solid praseodyillium was also measured·, by using the SSE method and metal-oxide equilibrium method.IntroductionWhen a direct current is passed through a solid alloy, not only electrons but also solute atoms are transported as charge carriers toward the anode or cathode. This phenomenon is referred to as an electrotransport or electromigration. The solid state electrotransport (SSE) is the application technique, based on this principle, to the pUrification of the solid metallic materials.Rare earth metals are used for various functional materials, such as magnetic, optical or electronic materials, therefore their high purity metals are required [l ,2]. However, rare earth metals are chemically active and have a strong affinity with gaseous elements (e.g. oxygen, nitrogen, hydrogen and carbon). In many cases, eliminating operations of gaseous elements have not been always made commercially, because these impurity elements could not be eliminated by usual treatments applied to the purification of ·common metals. As an alternative method, authors have proposed the· application of the SSE process to the elimination of gaseous impurities from rare earth metals. Investigations have been carried out on the yttrium-oxygen and neodymium-oxygen systems and the results were already reported[3,4]."

Jan 1, 2000

By A. G. Jackson, S. J. P. Laube

"Control of thin films during the growth process is dependent on several parameters that are difficult to monitor, including flux of film material, pressure, substrate temperature, composition, and thickness. One means for easing this difficulty is to take advantage of emission spectra associated with the process and the film. For pulsed laser deposition (PLD), the ion cloud generated by the laser has characteristic emission spectra that can be used to control the flux and, hence, the film. For chemical vapor deposition, the species present can be determined using mass spectroscopy and specific peaks can be used to control the deposition. Raman spectroscopy affords the possibility of real-time control by sensing characteristic peaks associated with film composition and thickness. These spectroscopic methods offer a real-time alternative to process control that is very attractive, because of the ability to accurately control films to achieve the engineered structures and properties sought. Examples are presented to illustrate the capabilities of these methods for thin film preparation.IntroductionThe drive to reduce costs and improve efficiencies of operation sets the tone for much of research, basic or applied. Basic research is limited by the ability of sensors and associated instrumentation to measure parameters accurately and reproducibly. Applied research has the same limitations and also the added constraints of time and costs. Hence, there are strong incentives to explore means for refining existing sensors with respect to performance and cost, as well as finding new sensors and techniques for more accurately and rapidly measuring quantities of interest in experiments and in various processes."

Jan 1, 1997

By Leonard J. Friedman

The contact process for the production of sulfuric acid has been used commercially since before the turn of the century (1880?s), and rapidly replaced the chamber process after the development of vanadium catalysts in the early 1900's (1910's - 1920's). Plant size has increased from a few tons per week to single train units in excess of 4,000 tons per day. Much of the history of the contact process is in the minds of the few remaining early process pioneers that started in the industry in the 1920's and 1930?s, and in sulfuric acid industry books published in 1921, 1925, 1936, and the last Deucker and West in 1959. Since those not familiar with history are doomed to repeat the failures and mistakes of the past, this paper includes a brief history of the contact process along with the history and development of equipment and materials in each equipment area of the process. The main focus of the paper is to present the development and analysis of equipment and materials in the contact section of the sulfuric acid plant - from the dry tower to stack.

Jan 1, 1999

By S. P. Mathew

The ISASMELT Lead Process is a continuous two stage process for the production of crude lead from concentrate. It is based on the use of a top entry submerged Sirosmelt lance to produce turbulent baths in which high intensity smelting or reduction reactions can occur. The process involves oxidizing the concentrates in the first stage to produce a high lead slag. This slag is tapped continuously and transferred down a launder to a second furnace where it is reduced with coal. Crude lead and discard slag are tapped continuously from this furnace through a single taphole and separated in a conventional forehearth. Process and engineering design work for a commercial scale Lead ISASKELT plant designed to produce 60000 tpa crude lead has been completed. This plant is planned to be operational in 1991.

Jan 1, 1990

By J. P. Constantinea

The use of fluidized beds for the roasting of zinc sulphide concentrates marked a milestone in the electrolytic production of zinc. Stable operation of a fluidized bed for zinc roasting requires a particle size distribution that minimizes the risk of defluidization and helps control carryover to manageable levels. However, the understanding of the roasting process is limited, and changes in operating conditions mainly rely on intuition, experience, and trial and error. A research program has been initiated at UBC to study the phenomena that influence the particle size distribution of fluidized bed zinc roasters. In preparation for the experimental phase, this paper reviews the current literature on the phenomena that affect the particle size distribution during fluidized bed roasting and other fluidized bed processes.

Jan 1, 2002

By Tsisana Gagnidze

A processing of technogenous wastes, which involve a gold-containing sulphide minerals, is a potential source to supplement the gold reserves. Hence, searching of ecologically safe and economically reasonable methods for processing of gold-containing technogenous wastes is a topical problem. To increase a parameters of gold extraction and to simplify a technology of the processing of above-mentioned wastes of sulphide minerals, an investigations have been carried out in the direction of the use of the method of electrochemical leaching without any preliminary processing of the mineral. It was established experimentally that an introduction of nitrogen containing organic additive into chloride solution favours to reduce a Red/Ox potential of the solution from 0,8÷1,2 V to 0,35÷0,5V, which permits to conduct the process of direct electrochemical leaching at ?soft? oxidation regimes at temperatures 20-300C C without an environmental contamination by molecular chlorine and with a high degree of a gold extraction up to 80-90%.

Jan 1, 2008

By R. Padilla

Enargite (Cu3AsS4) occurs normally associated with copper sulfides, mainly chalcopyrite. When the enargite content in chalcopyrite concentrates is high, direct smelting of the concentrate presents problems related to environmental pollution and contamination of the final metallic copper. Leaching processes are viable alternatives to treat copper concentrates with high content of enargite. Consequently, in this paper, the pressure leaching of enargite in sulfuric acid-oxygen system is discussed. The leaching rate was studied in the range 160 to 220 °C and partial pressures of oxygen of 74 to 200 psi. The enargite dissolution increased substantially with temperature increase. Complete dissolution of enargite was obtained at 220°C, and 100 psi of oxygen pressure in 90 min. The shrinking core model controlled by surface reaction was used to analyze the kinetics of enargite dissolution. Activation energy of 70 kJ/mol was obtained for the temperature range 160 to 220 oC.

Jan 1, 2008