Search Documents

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By Julie M. Melluish

The metallurgical response of the Point Leamington deposit has been studied. Two series of bench tests were conducted and various ore samples and flotation products were examined using image analysis techniques. The majority of sphalerite and chalcopyrite grains in this texturally complex ore were found to be smaller than 10 micrometres. Copper recoveries were low with losses mainly as fine inclusions in pyrite. Sphalerite recoveries were somewhat better due to a generally coarser habit. Gold and silver recoveries were also low and only solid solution silver was identified in the ore. The deposit shows poor economic prospects unless additional tonnage of high grade zinc ore can be delineated.

Jan 1, 1989

By H. L. Ludtke

Microlaminate composites were fabricated by electron-beam physical vapor deposition. The microlaminates consisted of five layers, each 2 to 4 pm thick, and were composed of either pure metal layers (Cu-Ag), or alternated between metal and intermetallic layers (Nb(Al)- Nb3Al). The microlaminates were heat treated in an Ar atmosphere for 2 to 12 hours, at temperatures of 600°C for the Cu-Ag and 1000°C to 1200°C for the Nb(Al)-NbsAl. Microlaminates were examined after deposition and after heat treatment by scanning electron microscopy and energy dispersive x-ray spectrometry. The effects of heat treatment on the morphological stability of these composites will be described.

Jan 1, 1999

By Charles Zimmerman

The Genesis gold mine, owned and operated by Newmont Gold Co., is located in section 31, T36N, R50E within Eureka County, Nevada along the Carlin Trend of sediment-hosted disseminated gold deposits. Mining commenced in 1986 with present mineable and stockpiled reserves listed at 17,711,000 tons of ore averaging 0.073 opt Au, totalling 1.292 million ounces of gold. Ore is primarily hosted within Devonian calcareous siltstones that have been subjected to intensive argillization and silicification episodes. Additional mineralogic and geochemical features of the Genesis ores include enrichment in iron-oxides, kaolinite, arsenic and antimony; the ore zone is relatively depleted in carbonates and sulfides as a result of supergene and hypogene oxidation. Two major structural zones enhanced the permeability of the siltstones and served as the main hydrothermal conduits within the deposit. Prior to the main ore stage, the host rocks were subjected to metasomatic effects caused by emplacement of the Juro-Cretaceous Goldstrike granodiorite pluton and associated dikes and sills. Micron-size gold occurs in clays, micro-crystalline quartz, and in arsenical complexes. Non-oxidized carbonaceous and sulfidic ores and silica-locked ores result in variable preg-robbing and refractory responses during cyanide recovery. Selective mining and milling has resulted in the successful treatment of the Genesis orebody.

Jan 1, 1988

By Chang Wei, Fan Zhang, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Marmatite is an important resource of zinc, which exist in forms of high iron and high indium. In order to recycle the valuable metal from these ores, the testwork of simultaneous leaching on neutral residue mixed with zinc concentrate of high iron and high indium has been conducted. The primary objectives are to leach the zinc and indium remaining in the neutral leach residue as ferrite using acid, and to reduce the ferric iron in solution to the ferrous by zinc concentrate, thereby extracting the zinc and indium in the zinc concentrate. The results indicated that in the following conditions, mass ratio of neutral residue to zinc concentrate of 1:0.25, particle size of 74-58 μm, initial sulfuric acid concentration of 150 g/L, liquid to solid ratio of 8 L/kg, temperature of 90°C, reaction time of 4h, the leaching efficiency of zinc and indium were over 95%, nearly 90% Fe was Ferrous in the leaching solution. This process effectively extracted zinc and indium and converted Fe3+ into Fe2+ in solution, and simplified the traditional process of reduction after leaching.

Jan 1, 2016

By George Kachaniwsky

Until mid-1982 the Mines Gaspe copper smelter consisted of a fluid bed roaster, a reverberatory furnace, two Peirce-Smith converters of which only one was blowing at any one time, anode casting facilities, and a single contact sulphuric acid plant treating both roaster and converter gases. Reduced concentrate supplies have led to the shutdown of the roaster and, as a result, it was necessary to adapt the converter and acid plant operation to the new operating mode: green concentrate smelting with resulting lower matte grades and acid plant treatment of off-gases from only one blowing converter. Therefore, modifications were carried out to existing equipment and methods of operation and control. This paper describes the result of work done to obtain steady, maximum strength, converter off-gas flow and an efficient acid plant operation. Topics covered include: optimization of converter operation, tightness of hood and off-gas ducting, improvements in acid plant/converter communications and modifications of acid plant operation and control to cope with the fluctuations in converter gas flowrates and strengths.

Jan 1, 1983

By Jacqueline JAlexander

Two of the most important phenomena which govern the continuous casting process and determine the quality of the product are the fluid flow and the heat transfer. Steel flows into the mold through the ports of a bifurcated submerged entry nozzle (SEN), which directs the jet to the mold narrow faces where the superheat contained is dissipated on the solidifying shell. Many important aspects of the fluid flow in the mold are transient and difficult to control. However, the time-averaged flow pattern in the mold is greatly influenced by the nozzle geometry, the submergence depth and the mold dimensions. The aim of this work is to analyze the relationship between the heat transfer and the fluid flow pattern inside the mold using the CFD technique at several operating conditions.

Jan 1, 2009

By Fuming Wang, Lifu Hu, Changrong Li, Ruipeng Pang

The solidification structure of 430 ferritic stainless steel has been calculated in the solidification process by using 3D-CAFE model under the condition of water cooling. The calculated results consistent with those obtained from experiment. Under watercooling condition, the solidification structure consists of chilled layer, columnar grain zone, transition zone and equiaxed grain zone

Jan 1, 2015

By Pierre-François Bareel

EU legislation imposes ambitious recycling targets for various consumer goods. End-of-Life Vehicles (ELVs), scrap iron and various proportions of Waste Electrical and Electronic Equipment (WEEE) are processed by shredding plants which recover most of the metals but produce Shredder Residues (SR) which are landfilled. They represent 20 to 25 wt.% of the shredder input. Energy issues for the coarse fraction of SR are now largely studied. However, below 2 mm, the calorific value falls off drastically. These Fine Shredder Residues (FSR) represent up to 55 wt.% of the total SR. To meet European objectives other alternatives to landfilling must be considered for the FSR. The present paper describes a study carried out to characterise the FSR and investigates ways to process them and produce marketable products. Applying Gy's theory, a sampling procedure was conducted over two years to statistically quantify the variability of the physical and chemical properties of FSR produced by a Belgian post-shredding treatment plant. Macroscopic characterisation has led to the identification of four material categories which could be separated according to their physical properties: ferrous metals (more or less oxidised), non-ferrous metals, an organic fraction (plastics, rubber, textiles, foams, wood) and a minerals fraction (glass, ceramic, concrete). The entrainment of small metallic particles within the pores of organic fragments will affect the quality of the separations.

Jan 1, 2006

By Christian Trassy, Pierre Proulx

"Inductive plasmas are now commonly used in material processing: spraying, powder synthesis, densification or spheroidization. An inductive discharge presents, in the coil region, recirculation eddies due to the Lorentz forces, resulting in an axial backflow. If the central jet is strong enough to ""pierce"" the recirculation this axial backflow disappears on the centerline, but the external layer of the injection flow is skimmed by the remaining eddy, and particulates are rejected to the discharge periphery. To avoid this disadvantage, it is common to introduce the injection pipe inside the discharge, so that its outlet is positioned after the recirculation eddy. The powders remain confined in the axial zone, to the expense of shortened residence time.In order to increase the efficiency of the particle trajectories, a double flow injector has been designed. It enables the particles to travel closer to the axis, while the outer schrouding gas is skimmed and passes through the electromagnetic eddies. This injector is made up of two concentric tubes. The powders are injected with the carrier gas in the inner tube. A schrouding gas is injected in the annular space between the inner and the outer tubes. The powder is confined to the vicinity of the axis, resulting in a more homogeneous thermal treatment.Tungsten powders have been spheroidized with and without this device. Using the double flow injection, the spheroidization yield has been increased from 70 % up to 95 %.The design of such an injection device has. been studied and improved using numerical modelling. Another useful tool, a visualisation technique described elsewhere, has been used for the experimental study, that drastically simplifies the comparison between experimental and theoretical results: injecting yttrium oxide into the discharge results in a colorful display of the 4000 K isothenn: the ""cold"" zone, below 4000, appearing as red, and the ""hot"" zone as blue. Furthermore, it is of great industrial interest since it is a very cheap and efficient way to obtain a picture of an important isotherm."

Jan 1, 1999

By H. Virtanen

Outokumpu copper refining operations have a long history of expansions and application of new technologies. Outokumpu is a name known around the world for technological excellence in the field of base metals, and part of the policy of operations is continuous investment and investigation in new technologies. The results of this hard work sometimes are immediate and sometimes take years. The work done during the last years at the Outokumpu Harjavalta Metals copper refinery, together with a sister technology group Outokumpu Wenmec, has started to bear fruit in terms of the following radical developments and advances that are and will be applied to assure Outokumpu's position as the technology leader and a low cost and safe producer. Some of the developments discussed include the new anode and cathode design, mechanised electrode handling, cell design incorporating features facilitating full automation, automated short circuit detection and removal, automated on line anode slime removal, and high efficiency and intensity refining.

Jan 1, 1999

By Andreas Weber

Batrec operates a plant for the recycling of used dry batteries with a capacity of 3000 tons per year. The plant Is situated In a tourist area of Switzerland and has complied with all the strict emission restrictions. The process yields four products: FeMn. Zn, Hg and slag. No hazardous waste Is produced. All types of batteries can be treated.

Jan 1, 1995

By Dengfu Chen, Yi Yang, Chunmei Chen, Mujun Long, Shikai Gong, Junhao Sheng, Tao Liu

The relationship between thermo-physical properties of petroleum coke and temperature is of importance for determining of the operating parameters during the calcining graphitization process. In this paper, the variations of thermo-physical properties of petroleum coke versus temperature were investigated, such as the DSC-Tg curve, the specific heat capacity, the thermal diffusion coefficient, the thermal conductivity, and so on. The thermal analysis curve of petroleum coke showed synchronous thermal hysteresis at higher heating rates, indicating that a larger heating rate will cause delay of thermal effects. The thermal diffusivity of petroleum coke decreased during the calcining process. With increasing temperature, coefficient of heat conductivity and specific volume heat of the petroleum coke increased with a decreasing variation rate. The research provides a database for the calcining graphitization process of petroleum coke.

Jan 1, 2015

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By W. D. Cho

Fast dissolution of nonmetallic inclusions such as alumina particles in molten slags has been required in secondary steelmaking -ladle and tundish - to minimize the amount and the size of nonmetallic inclusions in steel products. In the present work, the dissolution behavior of alumina particles in molten CaO-A12O3 and CaO-A12O3-SiO2 slags at the temperatures between 1450 and 1550°C have been investigated in terms of kinetics and mechanism. Alumina particles were added directly into the slags and the variation of the particle size with time was determined using optical and electron microscopies. The conventional types of slag for ladle and tundish were included in the dissolution study. The effects of Al2O3, Siq, CaF2 and MgO contents on the dissolution rate of alumina particles have also been determined. The diffusion boundary layer between alumina particle and bulk slag phase has been observed and analyzed using SEM and EDS. Based on the analysis of kinetic data and the boundary layer, the dissolution mechanism has been discussed.

Jan 1, 2002

By O. A. Bascur

Applying the latest information technologies in mining and metallurgical complexes has become a serious challenge to management and technical teams. Emerging component design is changing the way the user relates to the desktop. Connectivity between mining and metallurgical process operations and their business systems has become a reality. Expanded use of plant information on the desktop is a standard tool for revenue improvement, cost reduction and adherence to production constraints. The industrial component desktop support access to information for continuous improvement and innovation by staff personnel and engineers. Collaboration between groups enables the implementation of an overall process effectiveness index based on losses due to equipment availability, production recovery and quality rate. The integration of information from mining, mineral processing and metallurgical performance monitoring increases production efficiency, even when many elements cannot be measured directly. Three case studies of large mining/metallurgical complexes are highlighted.

Jan 1, 1999

By John M. Rogers

Risk management has rapidly developed to become an integrated, holistic approach that now encompasses the main risk elements such as product quality control, occupational health and safety, security, environmental liability, social issues and related management information systems. Given the obvious economic benefits, a seamless blend of risk management components has become essential to allowing organisations to sustain a competitive advantage, and is also looked upon as an important attribute in organisational growth. Juxtaposed with this management philosophy is the global trend towards outsourcing, which has seen the emergence of independent, and specialist risk management organisations. The New Millennium will undoubtedly see a shift away from "in-house" risk management practices, and consequently, the selection of a suitable risk management partner - a major vehicle for improving shareholder value - will become an important strategic management decision.

Jan 1, 1999

By G. K. Ruhlandt, C. W. Kim

"A 3-D Finite Element Method program called ""SOLCAST"" has been developed to simulate the casting solidification process. Using the temperature recovery method to evaluate the latent heat of fusion and applying a new combination of the time integration scheme, SOLCAST reduces the computational time significantly compared to an existing commercial FEM program, and produces accurate results comparable to experimental casting results. Prediction of casting shrinkage porosity for A390 aluminum alloy will also be discussed. To make this FEM program useful for foundry engineers, this program was connected to a commercial pre- and post-processor.IntroductionBecause of recently increased competition, foundrymen must produce high quality castings more economically. Therefore, casting solidification analysis prior to casting production is an attractive way to reduce costs and development time.Although the actual casting solidification process is a very complicated phenomena, foundrymen could predict where shrinkage defects would occur based on a transient conduction heat transfer analysis that includes the liberation of latent heat. A numerical analysis is generally required to solve the heat diffusion equation with the latent heat diffusion term, because casting shapes are very complicated and pure materials are rarely used.Different numerical methods have been applied to the casting solidification analysis 1. Among them, a finite difference method 2 and a finite element method (FEM)3 are most commonly used.Each simulation method has one or more basic difficulties which are different for each method. These difficulties are:(1) Modeling casting shapes on a computer.(2) Time consuming computation.(3) Uncertain material properties."

Jan 1, 1986

By M. Misra

The prediction and assessment of the reactivity of acid mine tailings has been a subject of numerous studies. The conventional approaches such as sulfur content, pH, net acid generating capacity and conductivity are used for assessing reactivity of the tailings. In this paper a new non-invasive Impedance Spectroscopy (IS) technique is used for the determination of reactivity and acid mine potential of tailings. This technique is also used to establish the long term stability and leaching propensity of the tailings agglomerated with alkaline binders.

Jan 1, 1994

By Yingtao Zhang, Shaofeng Du, Yiming Rong, Wenjun Zhao, Gang Wang

"20Cr2Ni4A steel is a kind of high quality steel mainly used for manufacturing high-duty gears in the world. The high-duty gear with good performance must have wear and fatigue resistance properties. In order to get the good properties, the high-duty gear needs a high hardness gear surface and a good hardness gradient along the depth direction. In this paper, the samples were designed and a vacuum carbonitriding process was put forward to improve the surface hardness of parts for 20Cr2Ni4A. The process contained carbonitriding, quenching, cryogenics, and tempering process. The surface hardness and hardness gradient of carbonitrided samples were measured and the good microstructure was gained. The surface hardness is 67.SHRC and the case depth is 1.2mm.IntroductionSteels are widely used in industry, but the fatigue strength and the wear resistance of steel is much low. So the heat treatment process is put forward to improve the mechanical properties of steel. It can be improved by high-energy heat treatment methods for medium-carbon and highcarbon steel. Those methods will not alter the chemistry of the base metal [ 1].For low-carbon steels, carburizing and quenching should be used to improve the steels' mechanical properties, especially the surface properties. Compared with the carburizing, carbonitriding has more advantages, such as a short production cycle, low temperature and small deformation of parts. Carbonitriding is a modified form of gas carburizing, rather than a form of nitriding. The modification consists of introducing ammonia into the gas carburizing atmosphere to add nitrogen to the carburized case as it is being produced. Nascent nitrogen forms at the work surface by the dissociation of ammonia in the furnace atmosphere; the nitrogen diffuses into the steel simultaneously with carbon. Typically, carbonitriding is carried out at a lower temperature and for a shorter time than is gas carburizing, producing a shallower case than is usual in production carburizing [2]. As a material surface strengthening technology, carbonitriding has been widely used in the production [3]. And vacuum carbonitriding process is better than carbonitriding, because the vacuum carbonitriding temperature can be higher than carbonitriding without surface oxidation."

Jan 1, 2014