Search Documents

By R. Heikkilä

Today road construction sites utilize more and more information modeling in design phases as well as model based 3-D machine control systems in site operations. For main contractor, the management and control of all the site operations is a demanding task including also many challenges created by continuously developing new technology. In the paper, the main requirements for successful dynamic site management are introduced. The dynamic management means real-time possibilities for information acquiring, transfer and further utilization of the information in the management. An integration model to expand the current way of management and the utilization of present 3-D machine control systems is introduced. Different practical test results using two new different dynamic management systems are presented and evaluated. The first experiments and the results have been provided using the prototype system developed in a research project called DigiINFRA by the University of Oulu and Technical Research Center of Finland. Also, there have been tested a new commercial management system developed recently in Finland. In the conclusion, an expectation for the next generation for more dynamic road construction management methods is concluded.

Aug 1, 2013

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By Tad S. Golosinski, R. Larry Grayson

Online education is not new. During the last decade, it has reached the stage where many universities offer a variety of courses, degrees and programs without any associated residency requirements. The most successful of the online universities, University of Phoenix, offers hundreds of accredited programs for close to 100,000 students throughout the world (www.phoenix.edu). Online education is considered to be a valid equivalent to traditional, classroom-based education. It is best suited to the needs of mature students with full-time jobs and a desire to deepen their knowledge. While most of the e-business has experienced severe setbacks during the last two years, e-education shows no signs of slowing down. On the contrary, the number of students and institutions offering online education keeps growing. The value of e-education associated expenditures was expected to reach $300 billion in 2001 (Sanoff,2001), making it a serious and mature industry.

Jan 1, 2002

In many base metal sulphide concentrators reagents such as collector and cyanide are often added to the grinding mill as well as to the flotation circuit. Whilst good reasons can be cited for splitting the reagent addition in this way, the benefits of such are rarely quantified and the complex reagent-mineral-media interactions occurring during milling are often poorly understood in terms of pulp chemistry. A new laboratory batch grinding mill designed by Magotteaux allows the user to measure, monitor, and control the pulp chemical conditions during grinding when testing different ores and media. Some of these parameters include pulp pH, pulp Eh, temperature, gaseous atmosphere, and dissolved oxygen concentration. In a recent development, the mill has been coupled with a simple on-line reagent monitoring system, designed by CSIRO, which allows the levels of species such as xanthate and cyanide in the grinding pulp to also be measured continuously during milling using a robust UV detection system. In this way the uptake of collector during grinding and the rate and ex-tent of cyanide interaction with the minerals and media can be determined as a function of grinding time. A series of grinding tests using an Australian nickel sulphide ore was conducted with the coupled system in which the cyanide dose, xanthate dose, and media type were systematically varied. The xanthate and cyanide levels were monitored as a function of grinding time and the data collected are discussed in terms of the pulp chemistry of the system and implications for plant reagent dosing strategies.

Jan 1, 2014

By I M. Turnbull

QMAP (the Quarter Million Mapping Programme, 1:250 000 scale) is a geological mapping programme which will build a digital geological database of the whole country and publish maps and books to document it. The programme was established in 1993, following a recommendation by a review panel appointed by the Ministry of Research, Science &amp; Technology, and is funded by the government, from the Public Good Science Fund. The relevance and fundamental value of QMAP lies in the greatly improved geological knowledge it will provide for researchers and other end-users of geological information. &nbsp; QMAP research involves assessment of previous work, field and laboratory investigations in key areas, and data storage, manipulation and publication using Geographic Information Systems (GIS) computer technology. The QMAP digital database of New Zealand geology will be completed by 2006, as will the series of 21 full colour printed geological maps and accompanying explanatory texts. Two are already completed and published (Kaitaia and Dunedin), and six other projects are well advanced. &nbsp; QMAP information will also be available in digital form. Next year we hope to expand the scope of the programme to cover the reconciling and linking of many other earth science databases to QMAP, because we believe this will create a powerful research tool. The intention is to develop internet access to the databases, to make the information publicly available.

Jan 1, 1997

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992

By J. A. Kost

A survey of 80 coal producers was conducted to determine the extent and scope of respirable dust control research for underground coal mines and the current methods employed to control respirable dust. Results of the survey showed that proper face ventilation and an adequate water spray system are sufficient to comply with mandatory standards in room and pillar mining. Difficulties still exist with longwall equipment, auger miners and buring machines. In these cases, known dust control techniques are not sufficient to obtain compliance. Present state-of-the-art face ventilation and water systems were discussed in addition to the sampling program.

Jan 1, 1980

This report presents the results of a study of mill tailings disposal practices and potential tailings dam stability problems. Recognizing the long period of time that would be required to develop the technology and practices necessary to significantly improve refuse disposal safety, the Bureau initiated this research effort as a first step in that development. Volume 1 includes a summary of conclusions and recommendations resulting from the overall research effort; discussions of disposal systems and methods, geology, seismicity, hydrology, and materials characteristics; evaluations of investigational techniques; discussions of usable interim generalized investigational, analytical and inspection procedures; discussion of general principles and presentation of a tailings technology manual outline; and discussion of needed future research am recommended programs.

Jan 1, 1974

By K Kermanshahi, J Allen, MáHilden, M Powell, S Mwansa, S Palaniandy

Approximately 420 VertiMills« (VTM) have been installed in mineral processing plants throughout the world, mainly in tertiary and regrind applications plus several in secondary grinding duties. Metso Minerals (Metso) and the Julius Kruttschnitt Mineral Research Centre (JKMRC) have commenced a collaborative research program in stirred milling technology focusing on mill performance evaluation, model development and scale-up methodology. Industrial VTMs are being assessed using a consistent circuit survey protocol to evaluate the performance of VTMs in comminution circuits. The survey protocol includes identification and modification of sampling points, appropriate sampling techniques, controlled circuit stability, and best sample analysis practice. To initiate this study four surveys were conducted in the tertiary grind circuit in the Ridgeway Concentrator at Cadia Valley Operations (CVO) that treats the full circuit throughput of over 800 tph. To deal with the high feed rate the site opted to lead the world in the application of stirred mills by installing the largest VTM, at 3000 hp (2240kW) in closed circuit with a hydrocyclone bank. On average the operating work index was 13.1 kWh/t, reducing the secondary grind product by 40 - 50 ¦m to the required 80 to 100 ¦m range. The applied specific energy is relatively low in these low-intensity stirred media mills at 2.7 kWh/t. The size specific energy was 24.2 kWh/t-75¦m. Based on the survey and operating data the VTM circuit is performing well in this high-throughput tertiary grinding application, producing a sub-100¦m product.CITATION:Palaniandy, S, Powell, M, Hilden, M, Kermanshahi, K, Allen, J and Mwansa, S, 2013. VertiMill« - Development of circuit survey and performance evaluation protocols, in Proceedings MetPlant 2013 , pp 162-175 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Lester M. Adams

In 1980, the Bureau of Mines surveyed a group of mine seals in Randolph County, WV, to evaluate their effectiveness for reducing toxic pollutants in mine water discharges. The survey focused on 11 block wet mine seals, but mine seals of several other types were also examined. The seals were installed in 1966 and 1967 in abandoned drift portals by the Federal Water Quality Administration (FWQA), a predecessor of the Environmental Protection Agency (EPA), in cooperation with the Bureau of Mines and other Federal and State agencies, in a project known as Elkins Mine Drainage Pollution Control Demonstration Project. The seals were designed to prevent air from entering the mine portals while allowing mine water to flow out. It was believed that by preventing air from entering inactive or abandoned mines, the formation of toxic pollutants and acid mine drainage (AMD) could be reduced. Evaluation of the seals was based on water flow measurements, water analyses, and visual observations. The Bureau&apos;s 1980 data were compared with past data collected by the EPA. Several leaks and failures were observed in the clay seals, as evidenced by apparent blowouts and the absence of vegetation where the mine water surfaced. Analyses of the 1980 data indicated some improvement in the quality of water discharged from many of the wet air seals.

Jan 1, 1984

By Anna Gustafson, Sohail Manzoor, Håkan Schunnesson

Sublevel caving operation relies on the estimation of ore grade at drawpoints, as the mine management uses grade to decide whether the material at a certain ring should be loaded or abandoned. Grade is estimated in various ways, including visual estimation, density-based calculation, and sampling and assay methods. The grade estimation at the world’s two largest underground iron ore mines owned by LKAB in northern Sweden is based on the density difference between ore and waste. The calculations assume a constant swell factor, a theoretical fill of 100%, and a linear relationship between bucket weight and material grade. This study evaluated these assumptions in detail based on the loading data for 12,237 buckets and concluded that the method has some shortcomings which render the assumptions invalid. Further research is required to deal with these shortcomings to improve estimation of the material grade.

Oct 17, 2022

By A Paz, H Lehto, M +stholm, I Roitto

Nowadays, the demand for a finer grind in minerals processing has set new challenges within the industry, particularly for grinding technology. Apart from a finer grind, energy efficiency is also a key driver in optimising comminution technology.Stirred milling technology, already proven in many other industries, delivers a modern, sophisticated, flexible and energy efficient grinding solution for fine and ultra fine grinding in minerals processing. Fine grinding technology is utilised particularly in concentrate regrinding to complete the liberation of valuable minerals after the first stage of concentration. Maintaining the correct particle and particle size distribution of the regrind product is crucial for downstream process performance. Stirred milling technology offers the unique possibility for online control and optimisation of the regrind product particle size. This paper describes the basis of this online control possibility and discusses the implementation of stirred milling technology in minerals processing, particularly in regrinding applications. The paper will also outline management and control of fluctuations in feed rate tonnages as well as particle size fluctuations in concentrate regrinding.CITATION:Roitto, I, Lehto, H, Paz, A and +stholm, M, 2013. Stirred milling technology - A new concept in fine grinding, in Proceedings MetPlant 2013 , pp 190-201 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Guy Chevalier, Jean-Guy Chartrand, Louis Barrette, Daniel Michaud, Michel Fortin

"COREM has developed, specifically for the mineral industry, a mobile laboratory using the Laser-Induced Breakdown Spectroscopy (LIBS) technique. It has been used to perform onstream analysis (OSA) of the chemical composition of slurries in both gold-ore and iron-ore processing plants. Industrial tests have been carried out respectively at La Mine Doyon (Cambior), a gold-ore processing plant near Rouyn-Noranda, Quebec, and at QCM's iron-ore pelletizing plant in Port-Cartier, Quebec. The aim was to demonstrate that the LIBS technique is capable of providing information that meets the needs for process control. C, Si, Ca, Mg, Mn and Al were the elements targeted on iron ore while Cu, Fe, Ag and Au were targeted for gold ore. The results obtained meet or exceed the requirements for process control and consequently clearly show that the LIBS technique is suitable for industrial applications.The feasibility of OSA, through in-plant validations using COREM’s LIBS mobile laboratory, has been demonstrated in four essential aspects: slurry sampling, LIBS chemical measurement, robustness for continuous operation, and functionality for industrial operators.INTRODUCTIONThere is a general need for optimization in the mineral industry. Process control is a favoured means to achieve this goal (McKee 1991). Real-time knowledge of process status is the key to effective control (Da Silva 1994). Only a few techniques, such as XRF, NMR and digital imaging, are currently amenable to chemically monitor industrial processes (Braden 2002). LIBS is an emerging technique with appealing characteristics for on-line and real-time measurement of bulk material (Lorenzen 1992, Palanco 2000). While our ultimate goal is to provide our industrial partners with performing monitoring tools, a shorter-viewed objective is to demonstrate the feasibility of developing a LIBS system for OSA. The LIBS technique has shown interesting capabilities for measuring solids, liquids, dusts and gases. Our work has focused on mineral slurries (Barrette 1999 and 2001, Turmel 1999). Special equipment is needed to perform in-plant validations. A mobile laboratory based on the LIBS technology has been assembled for this task."

Jan 1, 2004

By V. Ferrari

This report documents the three-phase program to design, fabricate, test, and demonstrate economical and practical methods of reducing noise levels on underground coal mining portal buses (mantrip vehicles). The noise-control treatments applied to a production-model portal bus were as follows: ? Wheel/rail vibrations were isolated from the vehicle frame by inserting elastomeric materials between suspension components. ? Vibration-induced noise was reduced by replacing all large sheet metal panels (except floor plates) with damped steel panels. ? Motor noise was reduced by tight-fitting covers made from damped steel and lined with sound-absorbing material, and by elastomeric motor mounts. ? The standard spur gears used in the traction drive system were replaced with helical gearsets. The program achieved the goal of reducing the average sound-level to below 85 dBA for typical operating conditions.

Jan 1, 1981

By Enrique Roy Dionisio Calderon

O presente trabalho mostra a concepção de um modelo que permite gerar uma superfície de mínimo consumo de redutor (carbono) em Altos-Fornos. No seu desenvolvimento foram consideradas as condições de equilíbrio das reações de redução, os balanços de massa e de energia e parâmetros operacionais. Sua aplicação à redução em Altos Fornos é exemplificada para situações reais, baseada em banco de dados operacionais de uma usina siderúrgica. Foi possível, a partir de planos de corte nestas superfícies, gerar diagramas binários do tipo CR-RD (Consumo de Redutor-Fração de Redução Direta), com possibilidade de serem gerados “on-line” no processo. Dentre os resultados obtidos, destaca-se a identificação de inviabilidades termodinâmicas importantes do forno. Dentre elas o modelo permitiu, através de seus “outputs” gráficos, prever e acompanhar o fenômeno de “gelada de forno”, conferindo desta forma maior segurança operacional ao processo.

Aug 17, 2017

By C. Richard Groves

As the level of technology applied in the electrical measurement, control, and display portions of mine hoist systems continues to advance, the issues and concerns associated with the ramifications of the application of microprocessor technology on the safety-related aspects of these systems become paramount. This report, in part tutorial, addresses several aspects of these concerns. Beginning with discussions of microprocessor-based system architectures, the report addresses some existing and anticipated uses of this technology in mine hoist systems and discusses safety related considerations associated with the areas of data derivation; control and display panels; and system reliability issues. The report concludes with electrical maintenance and inspection considerations associated with the safety assurance of microprocessor based mine hoist systems.

Jan 1, 1986

By Igor Teixeira da Costa

Os pós fluxantes são formados por escórias sintéticas que em contato com o aço líquido deve fundir e gerar uma escória líquida. Suas principais funções são: lubrificar e controlar a transferência de calor entre a casca sólida do metal e o molde. Eles possuem composições diferentes para diferentes condições de lingotamento, sendo formados, basicamente, por CaO, SiO2, Al2O3, Na2O, CaF2 e podem conter MgO, Li2O, K2O e B2O3. Como alguns componentes influenciam diretamente na cristalinidade dos fluxantes, como o CaO, o MgO, o CaF2, neste trabalho serão analisadas quatro misturas de pós fluxantes com leves variações na composição de modo que possa gerar cristalinidades diferentes. Para esta análise será utilizada o método de lâminas delgadas, com auxílio de um microscópio óptico de luz transmitida, que tem apresentado resultados bem satisfatório sobre o detalhamento da cristalinidade dos materiais.

Oct 30, 2017

By Rushikesh Battulwar, Javad Sattarvand, Joseph Seamons, Masoud Zare

In the last decade, new developments took place in the area of indoor positioning (or localization). Since the Global Navigation Satellite System (GNSS) cannot be used in underground mines, other technologies are needed for localization. Positioning and communication options today primarily include Wi-Fi, Bluetooth Low Energy (BLE), Ultra-Wideband (UWB), Radio Frequency Identification Device (RFID), etc. Smartphones and tablets currently have an array of sensors and radios, which can provide valuable information to allow indoor localization via various methods. Where mineworkers could keep smartphones with them, they can be highly effective at enabling localization and navigation. Recent applications of these technologies in underground mines have been thoroughly reviewed and examined for the likelihood of their utility for accurate localization where no other means exist. Some critical challenges and gaps that need to be addressed in future research have been identified.

Sep 5, 2021

By Hugh R. Rhys

The question of the desirability of recovering cullet from MSW in order to recycle it into the manufacturing of glass containers remains a controversial one. The main factors appear to be: 1. The position of the Glass Container Manufacturers Institute (GCMI), as the trade association for most container manufacturers, is that post-consumer cullet is a vital source of raw material. Present requirements are for: a) Flint cullet b) Non-flint cullet of known mix proportions c) Mixed unsorted cullet of known mix propertions c) Mixed or non-flint cullet of unknown mix proportions. A market balance for these products exists, and this might somewhat limit the outlets for (b), (c) and (d), or severely limit the outlet for (d) alone. 2. The color specifications are rather strict. With cullet admixtures of 20% of the melt or more, and the use of decolorisers in a flint furnace discouraged because their action is reducing in a process which requires an oxidising environment, color contamination in a flint furnace is serious.. For amber and green furnaces (reducing) it is less serious, but in order that the quantity of decolorisers may be controlled, the color balance (as a measure of the Fe and Cr content) of the admixtured cullet should be known. 3. Why not simply color analyze, either by a continuous on-stream or off-stream: photo-electronic analysis, or by systematic batch sampling (with some kind off electronic surveillance of the mainstream) and just send mixed, color measured cullet to only amber and green furnaces? The flint would-be simply included in the mix. This is probably technically feasible, but is subject to the market limitations noted in point1.

Jan 1, 1975

By Bureau of Mines Staff

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine venti lation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which ,accounts for a major portion of the market for coal, received further study. Unique power generation systems, inc luding coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jun 1, 1965