Search Documents

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By K. Yamaguchi, Sekimoto. H.

"Platinum Group Metals (PGMs) used as catalyst which reduces toxic substances in emission gas exhausted from an automobile should extensively be recycled because they are rare metals produced only at the limited regions. The recycling process is to smelt an alumina honeycomb, in which PGM is built, in molten iron with flux such as lime and silica to separate them. PGMs are concentrated in molten iron while alumina in slag.The objective of this study is to understand the factor to concentrate PGMs in liquid iron as much as possible. Fundamental research of the distribution of the PGMs between the slag and liquid iron was carried out to recover the value metals of platinum, palladium and rhodium from the three-way auto catalyst. The distribution ratios of platinum, palladium and rhodium between the Al2O3-CaO-SiO2 slag and liquid iron are from 10-6 to 10-5, and these are concentrated in comparison with slag phase by about 1 million times to the liquid iron at 1873 K. The distribution ratios of platinum between the FexO-CaO-SiO2 slag and liquid iron decrease from 0.1 to 2?10-4 with increasing the CaO content in the slag. The CaO addition to the FexO unary slag is effective in concentrating platinum in molten iron.Based on the distribution ratios obtained in this work, recovery of PGMs was determined. The recovery of platinum, palladium and rhodium increase with increasing the mass ratio, Mmetal/Mslag. In the case of the conditions of Mmetal/Mslag = 0.04, the recoveries of PGMs showed more than 99.97%. The use of liquid iron and carbon saturated liquid iron as the collector metal is advantageous for the PGM recycling of the three-way auto catalyst. We found that PGMs are enriched to the molten iron or the carbon saturated iron and the slag loss of PGMs is negligible small."

Jan 1, 2014

By S. Saito, P. A. Beck

The crystal structure of MoNi3 was determined by means of X-ray diffraction. This structure is isotype with that of ovgered TiCu3. The lattice parameters are: a. = 5.064A, bo = 4.224A, co = 4.448A, and zf 0.157. If the orthorhombic distortion (slight relative to the corresponding orthohexagonal unit cell) is disregarded, the structure may be described in terms of a close-packed ordered atomic layer, stacked in the sequence: abab. The structztres of ordered TiCu3 and TiAl3 are homotectic. The three types of ordered hexagonal phases, iso-structural with TiNi3, MgCd3, and VCo3, are known to occur in AB3 alloys of transition elements of the first, second, ad third long periods. It was noted1 that phases with the TiNi3 structure occur selectively in alloys of Ti-group elements with Ni-group elements. In AB3 alloys of Ti-group and V-group elements with Co-group elements the AuCu3-type structure predominates.' The vCO3 structure, which was determined very recently,' has hexagonal symmetry, but the actual atomic arrangement here, too, is rather closely related to the ordered cubic structure of AuCu3-type. However, an ordered hexagonal close-packed structure of the MgCd3-type occurs in MOCO33 and WCO3.4 Consequently, the question arises as to whether or not the crystal structure of MoNi3 is also of the MgCd3-type. Grube and winkler5 found that MoNi3 has a hexagonal close-packed structure with a = 2.54A and c/a = 1.65. They pointed out that some additional weak diffraction lines could be observed in the powder pattern, which may have been due to an ordered atomic arrangement in this phase. However, no detailed information was obtained by them and the structure was apparently not further investigated by others. The present work was, therefore, undertaken in an attempt to determine in detail the structure of MoNi3, and to investigate the possibility of ordering. EXPERIMENTAL METHODS Alloys used in the present work were arc-melted in a water-cooled copper crucible under helium atmosphere. Electrolytic nickel and molybdenum, both 99.9 pct pure, were used. Chemical analyses were not made, but the melting loss was not higher than 2 pct for any alloy. Ingots were first homogenized at 1200°C for 48hr, quenched, heavily cold worked, and then annealed at 820" or 860°C for 1 week, followed by quenching in cold water. Powder specimens for X-ray work were prepared by crushing the heat-treated solid specimens. In order to remove strains, the powders were reannealed in evacuated scaled fused silica capsules for 6 hr at the same temperature at which the corresponding solid specimens were annealed. X-ray photographs were taken with an asymmetric focussing camera, using unfiltered CrK or CuK radiation. EXPERIMENTAL RESULTS The X-ray diffraction patterns of alloys containing 20.8, 25, and 26.4 at. pct Mo, homogenized at 1200°C, showed the face-centered-cubic structure of the Ni-base a-solid solution. It was revealed, however, by micrographic examination that the 26.4 at. pct Mo alloy contained in addition very small amounts of a second phase, in accordance with the phase diagram.6 On the other hand, the 20.8 at. pct Mo alloy after annealing at 820°C gave the X-ray diffraction pattern of the ordered face-centered-tetragonal MONi4.7 In this pattern several additional weak diffraction lines were also observed, corresponding to the strongest diffraction lines of MoNi3. The alloys containing 25 and 26.4 at. pct Mo after annealing at 820" or 860°C gave X-ray diffraction patterns, as shown in Tables I and 11, corresponding to MoNi3. Each one of the reflections which could be tentatively indexed on the hexagonal close-packed cell of Grube and Winkler,5 with the exception of the basal plane reflections, was split into a doublet, as seen in Table I. Since microscopically the alloy consisted of a single phase, it seemed probable that the lattice of MoNi3 is actually slightly deformed, as compared with the tentative hexagonal unit cell. In addition to these diffraction lines, several weak lines were also present, as shown in Table 11, which could not be indexed at all on the hexagonal close-packed cell considered. Satisfactory indexing of all diffraction lines observed was found to be possible by using an orthorhombic unit cell with ao = 5.064A, ft = 4.224A, and c = 4.448A. These values, whose accuracy is estimated to approximately ± 0.008A, correspond to 95.14A3 for the volume of the unit cell, and to an X-ray density of 9.50 g per cm3. If no attention were paid to the weak reflections listed in Table II, a reduced -unit cell of half the volume (a = 2.532A, b = 4.448A, and c = 4.224A), closely related to the orthohexagonal cell, might be used. The dimensions of the orthohexagonal cell of the same volume as the reduced cell are: a = 2.562A, b = 4.437 A, and c = 4.183A. It may be seen that in the reduced cell the a axis is slightly shorter, while the b and c axes are slightly longer than those corresponding to the orthohexagonal cell of the same volume. This slight orthorhombic distortion is re-

Jan 1, 1960

By L. Mabiza

Keywords: Pyrometallurgy, furnace, sulphur, SO2, off-gas, Zimplats Zimplats embarked on an off-gas sampling campaign in December 2009 to characterise the concentration of SO2 in the off-gas from their 13 MW furnace. In excess of forty isokinetic samples (US EPA Method 8) were taken over seven days. The aim of the sampling campaign was to increase the understanding of factors that influence sulphur release from sulphide concentrates in an electric furnace. Specifically, detailed monitoring was conducted over various operating conditions to evaluate: ? The relationship between SO2 and feed rate (i.e. furnace power) ? The relationship between SO2 and ingress (i.e. furnace freeboard pressure) ? The impact of concentrate bed thickness on SO2 (i.e. blacktop) ? The effect of events such as tapping and converter slag return on SO2 ? The desulphurization reactions that take place in the blacktop A model was developed to predict the SO2 content in furnace off-gas for a particular set of operating conditions. In order to evaluate the impact of random, uncorrelated changes in concentrate composition, ingress and power (feed rate) on the SO2 content of the off-gas, a Monte Carlo approach was adopted whereby concentrate composition, power, and ingress were allowed to vary randomly around selected set-points. The model is primarily based on the release of ?labile? sulphur from the partial thermal dissociation of sulphide minerals with an over-stoichiometric sulphur content (e.g., Fe7S8 decomposition to FeS and S). The main findings of this work suggest that labile sulphur does not fully account for the measured SO2 content of the off-gas, and that limited oxidation of sulphides during melting also contributes to the SO2 content. Details of sulphide oxidation reactions in the furnace remain unclear, and it is currently not possible to provide a theoretical framework for the relationship between the extent of oxidation and variables such as temperature, gas composition, particle size, and residence time in the furnace black top. Through the use of the Monte Carlo model it was, however, possible to constrain the extent of sulphide oxidation to about 1%. This work has shown in practice what was expected in concept, that SO2 in off-gas is proportional to furnace power and ingress rate. The model that was developed consistently slightly under-predicts the quantity of SO2 generated. It also highlights that more work is required to better understand the analytical methods used to analyse for SO2 in off-gas.

Jan 1, 2011

By Robert C. Weisner

Current production costs and market conditions in the potash industry of the Carlsbad area were studied to determine the potential values of the potash mineral resource that would be lost or foregone if the Waste Isolation Pilot Plant (WIPP) facility is constructed on the proposed site in that area. The purpose of the WIPP project is to investigate the possibility of developing a nuclear waste disposal plant in the salt formations at the site. Analyses were made of all potash deposits determined to be in the site. Mining and processing under the most favorable recovery systems were considered. Value determinations were based upon estimated operating and capital costs of current mine-mill operations in the Carlsbad area. This study was made for the Energy Research and Development Administration (ERDA) by members of the Federal Bureau of Mines Minerals Availability System staff.

Jan 1, 1979

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission in metal/non-metal mines over a wide frequency range from 0.2 - 1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types include oil shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most important mining techniques. The results show that transmission at medium frequencies are optimum for wireless mine communications, in agreement with extensive testing previously performed by the authors In coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Aug 1, 1981

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran

In this paper we develop a physics-based model for lining erosion in steel ladles. The model predicts the temperature evolution in the liquid slag, steel, refractory bricks, and outer steel shell of the ladle. The flow of slag and steel is due to forced convection induced by inert gas injection, vacuum treatment (extreme bubble expansion), natural convection, and waves caused by the gas stirring. The lining erosion takes place by dissolution of refractory elements into the steel or slag. The mass and heat transfer coefficients inside the ladle during gas stirring are modelled based on wall functions which take the distribution of wall shear velocities as a critical input. The wall shear velocities are obtained from computational fluid dynamics (CFD) simulations for a sample of scenarios, spanning out the operational space, and a model is developed using curve fitting. The model is capable of reproducing both thermal and erosion evolution well. Deviations between model predictions and industrial data are discussed. The model is fast and has been tested successfully in a ‘semi-online’ application. The model source code is available to the public at [https://github.com/SINTEF/refractorywear].

Apr 16, 2024

By A. C. Fieldner

THE Bureau of Mines has received many requests for Information concerning the methods its laboratories use for analyzing coal and coke and determining their heating value. The fuel investigations now conducted by the Bureau of Mines are an outgrowth of the work undertaken at the Government coal-testing plant erected in 1904 at the Louisiana Purchase Exposition in St. Louis, and the methods for proximate and ultimate analysis of coal used by the Bureau of Mines are based on those originally adopted by the chemists of the coal-testing plant and followed in the subsequent chemical work of the Government fuel-testing plants at St. Louis, Mo., Norfolk, Va., and Pittsburgh, Pa. The many valuable suggestions and criticisms received from N. W. Lord, director of the School of Mines, and from E. E. Somermeier, professor of metallurgy, of Ohio State University, at that time, are greatly appreciated; development of many of the methods for the proximate and ultimate analysis of coal now used by the Bureau of Mines is chiefly clue to these men.

Jan 1, 1951

By Carline Fabiane Stalter

O presente trabalho tem por objetivo buscar e aplicar ações de P+L no processo de colagem. Este é realizado em uma cabine de formato cúbico, cujo material colante é o adesivo de poliuretano. Como a aplicação sobre o substrato é feita com uma pistola específica, ocorre a formação de névoas e consequentemente sua deposição nas paredes da cabine, formando camadas de adesivo que devem ser removidas e descartadas como resíduo. A fim de facilitar sua remoção, as paredes eram revestidas com graxa, que acabava contaminando o resíduo. Com as ações de P+L, buscou-se eliminar a graxa do processo. A partir daí, foi realizada a avaliação econômica e ambiental. A melhor opção para eliminar a graxa seria utilizar um produto que agisse como desmoldante, por isso foi testado o tecido de fibra de vidro com Teflon®. Como os testes realizados apresentaram resultados satisfatórios, houve a substituição da graxa. Dessa forma houve a redução de custos e no tempo de limpeza da cabine, não geração de graxa como resíduo, possibilidade de reaproveitamento do resíduo, eliminação do contato entre o operador e a graxa, transformação de um resíduo classe I em classe II e retorno financeiro do valor investido em 1,1 meses.

Aug 16, 2017

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

Accident data indicates that mobile haulage poses a significant pinning, crushing, and striking risk. Proximity detection systems (PDSs) have the potential to protect mineworkers from these risks. However, unintended consequences of mobile PDSs can undermine the safety benefit they provide. Soliciting iterative user input can improve the design process. Users help provide a critical understanding of how mobile PDSs may hinder normal operation and endanger mineworkers. Researchers explored users’ perspectives by conducting interviews with mineworkers from seven mines that have installed mobile PDSs on some of their haulage equipment. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance, and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure, and risk. Mineworkers also suggested that improved task compatibility, training, logistics, and PDS performance might help address some of these identified issues. This paper also gives additional insights into mobile PDS design and implementation.

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

Accident data indicates that mobile haulage poses a significant pinning, crushing, and striking risk. Proximity detection systems (PDSs) have the potential to protect mineworkers from these risks. However, unintended consequences of mobile PDSs can undermine the safety benefit they provide. Soliciting iterative user input can improve the design process. Users help provide a critical understanding of how mobile PDSs may hinder normal operation and endanger mineworkers. Researchers explored users’ perspectives by conducting interviews with mineworkers from seven mines that have installed mobile PDSs on some of their haulage equipment. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance, and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure, and risk. Mineworkers also suggested that improved task compatibility, training, logistics, and PDS performance might help address some of these identified issues. This paper also gives additional insights into mobile PDS design and implementation.

By Thomas L. Richardson, David R. Chapman, Gary W. Gilbert

The two contracts of the Big Walnut Augmentation/Rickenbacker Interceptor(BWARI) sewer project for the City of Columbus, Ohio total nearly 35,000 feet of 14and 12-foot diameter tunnel. EPB TBMs will install precast concrete segmental lining through difficult glacial soils ranging from clean granular to hard till with high groundwater and boulders, crossing roads, railroads, and a large stream. Construction of 12 shafts and a large Interconnect Structure involving major ground stabilization work is required. The paper will review design of major project elements and present an update on construction progress.

Jan 1, 2005

By A Giblett, K Afewu

This paper uses a case study to demonstrate best practices techniques for predicting the contribution of gravity concentration in a gold recovery process flowsheet. The case study was selected as an example of an ore with a marginal gravity gold content, which makes the value of a gravity circuit difficult to quantify. In this instance the value of leveraging a significant knowledgebase of operating gravity circuit performance to support the decision making process was demonstrated. This case study analysis serves as a useful demonstration of best practice methodologies supporting decisions to include or exclude gravity recovery in a gold recovery process flowsheet.CITATION:Giblett, A and Afewu, K, 2015. Do we need a gravity circuit or not? A case study in applying best practice, in Proceedings MetPlant 2015, pp 288–295 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Bemd. E. Langner

At Norddeutsche AfFmerie the CollaMat is an important instrument for controlling the activity of glue in copper electrolyte. Thanks to on-line measuring of the glue activity appropriate action can to taken in the event of sudden changes, such as an intemption in the glue supply, as well as long-term trends, such as continuously decreasing glue activity over days or weeks. Laboratory tests on the dependence of glue degradation on temperature have shown that relatively small increases in temperature of only 3OC cause the half change value of the glue degradation to reduce by 25 %. It is a similar picture with the sulphuric acid concentration in electrolyte. An increase in the acid concentration from 160 g/l to 200 g/l can - depending on the temperature - likewise result in a decrease in the half change value of up to 25 %.

Jan 1, 1995

By Carl G. Bock

INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has let a contract for the excavation of three rock stations, spaced about 3550' (1082m) apart, beneath Connecticut Avenue in Washington, D.C. Two previous rock stations have been completed, one of which had a crown pilot tunnel excavated to explore geologic conditions that would be encountered during the station excavation. This pilot tunnel was primarily for inspection by bidders and design was based on core hole information. The other rock station had no pilot tunnel and was also designed on the basis of core hole information. The three rock station areas, which are the subject of this paper, have been explored by crown pilot tunnels and an as-built report, with geologic maps and sections, has been prepared, for use by the design engineer as the basis of design for support of the structures. The geotechnical report describes the geologic structure in detail and relates it to excavation and support of the three crown pilot tunnels and the running tunnels which will be enlarged to create the 58'W x 44'H x 700'(+)L (17.6m x 13.3m x 212m +) stations. The information was complete enough to permit the design engineer to visualize the geologic structure and compute loads for the various types of rock conditions. It was therefore possible to determine the size and spacing of the steel sets for the several different conditions of rock structure encountered in the pilot tunnels.

Jan 1, 1976

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests.

Jan 1, 1934

By R Moreby, J Kok, L van den Berg

The high production rates achieved from mass mining methods such as block caving, sublevel caving and longwall mining require large conveyor belts, trucking loops (diesel/electrical) and rail systems for ore handling. However, the ore handling systems used in mass mines introduce a significant amount of heat into the overall ventilation system, which may be problematic at depth or in mines located in hot climates.In particular, the heat load from a conveyor system is not always well understood and consists of various components, including frictional heat from idlers, heat from electrical motors, heat from the drive train and heat from broken rock transported on the conveyor system. This paper presents results from a study that investigated the heat introduced to the ventilation air from a large conveyor system. The conveyor system transports ore with a maximum virgin rock temperature of 41°C from a depth of over 1 km. Air, belt and rock temperatures were measured in the conveyor system to evaluate the distribution of heat loads.CITATION:van den Berg, L, Moreby, R and Kok, J, 2015. Heat load estimation from conveyor systems in mass mines, in Proceedings The Australian Mine Ventilation Conference, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Raymond M. Howe

Additional data have been secured on the disintegration of furnace linings and the spalling of stove brick. The first article on the disintegration of furnace linings appears to have been written by John Pattinson in 1876.l The furnace involved was 85 ft. (25.0 m.) higher and 27 ft. (8.2 m.) in diameter at the boshes; after being in blast five years, the top brick became contaminated with carbon and disintegrated. An examination of the lining showed that the discolored, disintegrated brick were in a zone found from 35 to 67 ft. (10.6 to 20.4 m.) above the hearth; immediately below, in a zone extending from 22 to 40 ft. (6.7 to 12.1 m.) above the hearth, the brick were hard and porcelain-like in appearance. Analyses of samples taken from the different sections are given in Table I. The water-soluble portion found in the sample taken 39 ft. (11.8 m.) above the hearth had a composition approximately as follows: silica, 0.50 per cent.; lime, 0.04 per cent.; potash, 0.78 per cent.; soda, 0.20 per cent.; potassium chloride, 6.19 per cent.; moisture, 1.03 per cent.; total, 8.74 per cent. The carbon Table 1.—-Analyses of Samples Taken from Diferent Sections of Furnace . I ii In Iv v Section 67 Section 45 Seotion 39 Section of Original ft Above ft above ft above vitrified Lining Hearth Hearth Hearth Portion Per Cent. per Cent per Cent per cent. per Cent Silica........................... 55.70 55.60 55.67 47.60 37.07, Alumina........................ 35.50 35.40 30.00 26.47 23.18 Ferric oxide..................... 3.00 1.32 0.96 Lime........................... 0.23 0.06 0.17 Magnesia....................... 1.22 0.95 0.86 0.00 Potash......................... 2.60 2.10 5.30 7.54 21.59 Soda.........,.................. 0.45 0.42 1.67 0-76 6.28 Ca1bon ......................... 2.05 3.24 5.97 Carbon dioxide.................................. 2.. 17 Water...................................... 7.70 Water-soluble........................... 8.74

Jan 1, 1920

By Gary R. Gavan

This report presents the results of a research project that gathered detailed information on the composition of the population of mobile equipment used in U.S. coal mines. A computerized data bank containing over 19,000 pieces of coal mine equipment in use in 1976 was prepared with a data retrieval program. Operator protective structure technology is reviewed; field problems experienced with ROPS are discussed.

Jan 1, 1978