Search Documents

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

The C.S.I.R.O. acid alumina process employs the essential steps of digestion, hydrolysis and calcination to produce pure alumina from ores too high in silica or too low in grade for the Bayer process. The two latter stages have been described in some detail previously but the digestion stage requires separate discussion since ores vary widely in composition and reactivity. Kaolinitic clays require roasting to 800°C to render the alumina soluble in the 11 per cent sulphuric acid used in the process while some ferruginous laterites require roasting to reduce the reactivity of iron minerals.The iron content of pregnant solutions is kept at a low figure by digesting at temperatures where the solubilities of ferric oxide or basic ferric sulphates are small. A two-stage, counter-current digestion is necessary to extract a high percentage of alumina from the ores and to produce a basic pregnant liquor with an SO3 : AI 203 ratio of 1'\1 suitable for high temperature hydrolysis. The second stage of digestion, called the modification stage, treats slightly acid liquors with excess of ore in the temperature range 1200-1400C.The first stage operates at 170°-1900C to extract further alumina from modification residues, using recycled acid obtained from later steps of the process. Both temperature ranges are critical for economic operation and for proper control of the iron content of solutions. In batch experiments, 30 min is regarded as a suitable retention time for digestion and modification; ores which require much longer than this are less suitable for the process. Impurities such as silica, and titanium and vanadium oxides are discarded in the residue along with iron oxide, and do not contaminate the final product. Bivalent metallic sulphates such as MgSO4, can build up in the circuit to a very considerable degree without affecting product purity.Comparison with other processes shows that the C.S.I.R.O. process is superior for control of contamination by iron, which is the major problem in acid processes. The pure intermediate product (3Al203.4S03.9H20) is also more convenient for calcination to alumina than the hydrated aluminium sulphate usually recovered in other processes. Detailed cost comparisons must await pilot-plant evaluation of the C.S.LR.O process.

Jan 1, 1964

By Conochie D. S, Grave N. C

Disposable-tip emf cells at present used in liquid steel can be used to measure the state of oxidation of high-iron slags produced in non-ferrous smelting. This provides a new tool for the control and evaluation of pyrometallurgical operations.An investigation of oxygen potential variations throughout a typical nickel smelter using the flash smelting technique gave a valuable insight into the process. Correlations of oxygen potential with ferric to ferrous oxide ratio and nickel content in slag were in reasonable accord with equilibrium data in the literature indicating that the probes may be used both as a plant investigation tool and possibly as a means of obtaining thermodynamic data for slags.

Jan 1, 1979

By N. Demirel, O. Gölbasi

Draglines are massive machines extensively utilized in opencast mines for overburden stripping. The demanding working environment induces fractures, wear and tear, and fatigue failures in dragline components and eventuates in extended maintenance, lengthy downtimes, and loss of production. The bucket is the main source of external loads on the machinery, since interactions with ground materials take place in this region. This study aims to develop a generic finite element model of the stress on an operating bucket. This entails (i) three-dimensional modelling of a dragline bucket, (ii) analytical estimation of resistive forces in the bucket movement, (iii) three-dimensional simulation of the moving bucket using finite element analysis (FEA), and (iv) sensitivity analysis to examine the effect of formation characteristics on stress variation. Simulation results imply that the drag hitch and digging teeth are the elements of the bucket that are most prone to failure. In addition, sensitivity analysis indicates that internal friction angle of the formation is the dominant parameter leading fluctuations in stress values. Changes in stress level are least influenced by formation density.

Jan 1, 2015

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By Edgar Apaza Huallpa

Os aços inoxidáveis duplex (AID), apresentam em geral uma microestrutura composta de austenita e ferrita em proporções aproximadamente iguais. Para ter o controle dos processos de fabricação e desempenho é importante conhecer sua evolução microestrutural, devido à precipitação de fases intermetálicas como sigma (s) e chi (?), que causam grave deterioração das propriedades mecânicas do material. Neste trabalho foi estudada a evolução da fase sigma (s) durante tratamentos térmicos em temperaturas intermetálicas (800°C-900°C) de amostras do aço inoxidável duplex tipo SAF2205 (DIN 1.4462/UNS 31803). Foi observada uma gradual redução da intensidade do sinal do ruído de Barkhausen com o aumento do tempo de tratamento térmico, indicando uma redução na fração de fase ferromagnética. Para tempos de tratamento de 24 horas, o sinal de Ruído de Barkhausen está quase totalmente inserido dentro do ruído de fundo da medida, indicando haver uma fração volumétrica bastante reduzida de ferrita. Por meio da produção de amostras padrão para calibração, essa pode ser uma via de avaliação não destrutiva de componentes submetidos em campo a temperaturas nas quais se formam fases intermetálicas.

Aug 8, 2018

By Zhongning Shi, Ramana G. Reddy

"By cyclic voltammetry and potentiostat electrodeposition using Potentiostat/Galvanstat, electrochemical behavior on Ag electrode in electrolyte 0.2M NaOH+0.01MPb(NO3)2-0.01M TeO2 -0.01M TlNO3 solution were also carried out at 298K. The processes of electrodeposition of Tl2Te3 and PbTl4Te3, a thermoelectric material, are reported along with analysis of the composition of the obtained deposits. The results showed that two different underlying processes are occurring depending on deposition potential. One process involves the reduction of TeO3 2- and Tl+ to Tl2Te3 in a potential interval of -0.70V < E < - 0.89V (vs. Hg/HgO). A second process at more negative reduction potentials involves reduction of TeO3 2-, Pb2+ and Tl+ to PbTl4Te3 in a potential interval of -1.02V < E < - 1.19V. The crystalline Tl2Te3 and PbTl2Te3 were deposited electrochemically on Ag substrates at -0.84V and -1.10V respectively. Thermoelectric (TE) material can form a temperature gradient across the material to make electric voltage, which is popular in waste heat utilization and recovery industry. Lead telluride, PbTe, is a small band gap semiconductor of 0.32eV at 300K. PbTe can change its n-type semiconductors with Pb-rich to p-type semiconductors with Te-rich[1]. And it is one of the best TE materials used in thermoelectric generators working between 500K and 600K, or even at a higher temperature of 800K.Three facto,rs play a role in the performance of a thermoelectric material: electrical conductivity (s), thermal conductivity(?), and the Seebeck coefficient (S). These can be combined with absolute temperature (T) to give a figure of merit (ZT) for the material, ZT = s2sT/?. By increasing the electrical conductivity and decreasing the thermal conductivity, which can enhance the ZT value, many efforts, such as alloying with other elements and making the materials nano-sized, have been done to improve its properties recently. Hsu et al. reported that the ZT value of Cubic AgPbmSbTe2+m is increased to 2.2 by doping Ag-Sb to PbTe.[2]."

Jan 1, 2011

By Danell. R. E.

A drill monitoring system has been developed which measures performance characteristics of a rotary drill and relates this to the material strength and rotary specific energy. The drill monitor is computer based and is used to produce a profile of the relative in-situ material strength as a function of depth. This information has been used in determining the placement of explosive in selective loading of blastholes and estimating the amount of lump product in a particular section of an ore body.

Jan 1, 1989

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By J. H. East, D. Harrington

"INTRODUCTION Mining at its best is not a clean occupation for either surface or underground employees; and this applies alike to coal, metal, and non-metallic mines. The employees are handling minerals that have been blasted, or broken by some means and are subjected to mineral dust, whether it is coal, quartz, or talc. The employees usually wear clothes specifically adapted to the work in which they are engaged, and frequently these clothes are not suitable for use away from the mine. Many mines are wet, and employees must wear rubber boots to remain at least partly dry, and even on relatively dry mines, some parts of the mines usually have water falling from overhead, there are accumulations of water, or the floor or other surfaces are wet or muddy, Some mines are dusty, and the air-borne dust quickly settles on the clothes and body of the miner, especially, when he is working in confined areas, or in places that are hot, humid, or poorly ventilated. Most occupations around a coal tipple, anthracite breaker, or a mill at a metal or nonmetallic mine have their own problems of cleanliness as to skin or clothes or both. Mining in any of its phases is inherently dirty work, and the employees dress accordingly while at work.In the early stages of mining it was the custom or workers to wear their dirty clothes home and change there. This necessitated their going home after work in dirty clothes which were usually damp from perspiration or from contact with wet or muddy matelials or surfaces, and, in addition to being inconvenient this was a frequent cause of colds, pneumonia, other pulmonary diseases or, possible skin ailments. Men working in very wet mines found that it was more satisfactory to change into dry clothes in the boiler room at the mine after work and allow their wet clothes to dry overnight. The mining companies later provided the first of the so-called ""dry-houses"" which were heated but had, few, if any, conveniences, such as showers, lockers, or latrines. The miners changed into dry clothes after work, but would not bathe or ""clean up"" until they reached their homes. Later, progressive mining companies provided bathing facilities for the employees, and eventually the present modern wash and change houses were evolved. Unfortunately, many mines, still have no bathing accommodations, and many have only makeshift accommodations."

Dec 1, 1947

By John A. Wells, Leticia Conca, Kenneth G. Thomas

"Since about 2002 there has been significant capital cost escalation, not inflation, in the mining industry causing turmoil for successful project completion. Project capital costs have more than doubled and some cases tripled in this time period. This has rendered many projects to be economically challenged and in some cases not viable. In addition higher than expected operating costs have further adversely affected project metrics such as NPV and IRR. Capital cost increases for projects have been widely reported globally. This current paper reviews three items. Firstly, why such capital increases and the various components that make up capital estimates. Secondly, it looks at reasons why preliminary estimates, for example at scoping and pre-feasibility level, have been lower than the ultimate constructed costs. Such increases and differences in estimates have caused major problems for mine builders and have led to a general nervousness on the part of those providing project finance. Thirdly, what discipline is needed in project execution in an attempt to mitigate such capital increases. The paper will hopefully give a better understanding of the various issues and factors involved for those in the mining industry.INTRODUCTION The years 2012 and 2013 were a turbulent time for the mining industry. The European economic crisis, politics, metal price volatility and a wave of changes of CEO´s in some of the major mining companies all contributed to a challenging couple of years. Two issues stood out. First, the huge increases reported in the capital costs of projects, where increases of 100% - 300% were not uncommon and in some cases exceeded that during the first decade of the 21st century. Second, company write downs related to takeovers during the boom and the stabilization/correction in commodity prices. These have led to great uncertainty, made it difficult (or impossible) to raise project financing costs, contributed to the changes at CEO level and placed many projects either on hold or cancelled altogether. It is commonplace now to read of companies talking of reduced capital expenditure and making a complete review of their projects and operations to contain costs."

Jan 1, 2014

By Pengfu Tan

Electric arc furnace (EAF) dust from the steel industries is listed by the United Sates EPA as a hazardous waste under the regulations of the Resource Conservation and Recovery Act due to the presence of lead, cadmium and chromium. The disposal of the approximately 650,000 tons of EAF dust per year in the U.S. and Canada is an expensive and unresolved problem for the majority of steel companies. The Waelz process has been considered as the best process for treating EAF dust. A process model, combined thermodynamic modeling with heat transfer calculations, has been developed to simulate the chemical reactions, mass and heat transfer and heat balance in the kiln. The injection of air into the slag and the temperature profile along the kiln has been modeled. The effect of (CaO+MgO)/SiO2 on the solidus temperature of slag has been modeled also and discussed. Some optimizing results have been presented in this paper.

Jan 1, 2005

By Walter Ccallo, Dante Soberón

El Batolito de la Cordillera Oriental, comprende una diversidad de rocas intrusivas, las cuales varían composicionalmente desde gabros a granitos alcalinos de la serie calcoalcalina. Durante su emplazamiento han sufrido procesos de fraccionación y contaminación en la corteza, dando como resultado granitos metaluminosos y peraluminosos. Los trabajos realizados por el INGEMMET, han permitido la agrupación de las diferentes rocas en unidades y súper unidades, conllevando a determinar tanto las características petrogenéticas, como las relaciones con las mineralizaciones polimetálicas y de elementos estratégicos para cada unidad.

May 1, 2008

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

The low-grade nickel laterite ore used in this study was successfully upgraded through selective reduction by industrialized rotary kilns followed by magnetic separation. The results indicated that both iron metallization extent and nickel metallization extent showed obvious linear correlation. In addition, rational roasting temperature and prolonged grinding time could enhance the overall fineness level of reduced laterite nickel ore. The moderate roasting temperature at a range of 1100–1150 °C should be suitable enough to a conversion of total nickel to metallic nickel and partly inhibited the conversion of total iron. Ultimately, the obtained ferronickel alloy with a nickel content of 7.32% and an iron content of 84.15% was prepared successfully from the lowgrade nickel laterite ore containing a nickel content of 1.92%. Nickel and iron recoveries were 96.72 and 89.08% respectively, which achieved the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore

In the extraction of level bridge pillars in the South Mine by square-setting methods the general practice is to work transversely from the hanging wall in narrow sections three or four sets wide to the depth of the bridge-usually three sets. When the working block attains an area of twelve square sets, sand filling is run in, either by pneumatic (Proceedings No. 123, 1941) or hydraulic methods, in order to control the settlement of the general area and prevent the development of undue weight in the stope. Upon completion of the filling operations, or coincident with them, ore breaking is resumed and the transverse section of the bridge pillar gradually reduced. A number of these parallel sections may be working at the same time.In preparing a block of sets for filling a great deal of paddocking is required, both to contain the filling and to preserve access to ladderways and ore chutes which may be situated at some horizontal distance. Stope paddocking until recently was constructed of 10 in. x 2 in. boards nailed...

Jan 1, 1942

By Ycaro Jorge Maia da Costa

O desenvolvimento de estruturas com dimensionamento confiável requer o monitoramento de seus materiais, entretanto alguns processos de fabricação muitas vezes induzem modificações em seu comportamento mecânico. Isso faz com que as estruturas sejam menos confiáveis podendo causar redução da vida útil. Um dos processos onde isso acontece é a soldagem. Seu aporte térmico, modifica a microestrutura do material de tal forma a gerar três regiões mecanicamente distintas na junta soldada: Metal de Solda (MS), Zona Afetada pelo Calor (ZAC) e Metal de Base (MB), fazendo com que haja concentração de tensão na região afetada. Este trabalho se deteve em analisar o comportamento mecânico de uma junta soldada de aço inoxidável AISI 304 em comparação com o mesmo material não-soldado através da identificação dos gradientes de deformação, utilizando da Correlação Digital de Imagens (CDI) aplicada ao ensaio de tração. Os resultados provaram a capacidade da técnica de CDI em identificar campos de deformação mesmo em materiais anisotrópicos, como uma junta soldada.

Aug 17, 2017

By Winfried Rosenstock

The development of electronic initiation systems has partially reached or will reach in a short period of time full reliability for general use without limitations. Unfortunately those systems meet with a fully unprepared mining community and is confronted worldwide with blasting procedures which are not suitable to exploit the full range of the electronic option. This is for the time being only belonging to quarrying and general surface mining, for the use in underground operations the detonator is still not yet competitive, apart from special cases. It is not to be taken in doubts that the introduction for underground purposes will follow in a less shorter or longer period of time.

Jan 1, 2003

By King E. J

Department of Pathology, British Post-graduate Medical School, London:The experiments here recorded were devised and carried -out during the last two years in an attempt to corroborate the important work of Denny, Robson and Irwin (1939) in which they found that experimental silicosis could be prevented by means of metallic aluminum. By causing rabbits to inhale powdered quartz for several months they induced experimental silicosis. These animals then served as controls for comparison with another group which were dusted with a mixture of quartz and aluminum. In the second group silicosis failed to develop.Our experimental procedure was somewhat different. We resorted to intratracheal insufflation instead of simple inhalation, and we used rats instead of rabbits: otherwise the essential features of the original experiments were carefully duplicated.EXPERIMENTAL PROCEDURES.A single dose of dust was delivered into the lungs of each animal. The dust was suspended in a fluid medium and injected by means of a syringe directly into the trachea in known quantity (technique of Kettle and Hilton, 1932). The suspensions were autoclaved before use and were injected with aseptic precautions. Having had a long experience of this technique we employed it with confidence and usually secured a fairly uniform dispersal of dust throughout both lungs. To carry out injections successfully one requires, above all, an even suspension of dust which will flow smoothly and quickly from the syringe. This is not difficult in the case of quartz, for, though it tends to settle out rather quickly, this can be avoided by constantly agitating the suspension. The syringe containing the inoculum may be shaken gently right up to the moment of injection and then emptied quickly to prevent sedimentation. Powdered aluminum is more difficult to handle, for the particles tend to flocculate and are not readily made to disperse evenly in saline, even by violent shaking. For this reason an emulsifying agent may be used to advantage, provided it does not complicate the experiment, a point to be mentioned again presently.THE EXPERIMENTSExperiments with quartz alone: Extensive silicotic lesions were produced in 23 out of 26 rats by the administration of pure quartz dust in doses of from 50 to 200 mg. per rat. The dust was so finely pulverised that the particles averaged about 1-p. in size: none was larger than 5 p. and 99 per cent. were under 2.5 p.Eight of these animals survived for seven months and were then killed...

Jan 1, 1945

By Janne Kauppi, Kaj Jansson, Piia Suvio, Saara Hagnäs

"Historically the focus at the mineral processing sites has been to improve the production operations, while little focus has been set on how factors, such as the quality of water used in the process affects the metal recovery. Simultaneously increasing public pressure and water scarcity is driving the mining industry to recycle more water back to the process, which in turn leads to accumulation of impurities within the recycled water. This paper presents a concept for a systematic approach on targeting the impurities that have a negative effect on the metal recovery at the flotation circuit by using a novel solution called Process Water Recycling Plant (PWRP). These plants are designed with specific ore type in mind. PWRP produces cost-effectively process water to different target qualities, especially for flotation purposes enabling higher and more stable flotation recovery. It consists of pre-designed and standard water treatment units for a wide range of volumes. The application-specific configuration of units is governed by the water quality requirements, and can be designed according to specific customer needs. Testing has been carried out in order to investigate, which recycling water impurities affect the different ore types and how the metal recovery in flotation is affected as a consequence of the poor-quality water. The results indicate that every ore type is impacted differently and without a good understanding on how the water quality impacts the process performance, adverse effects on the flotation recovery can occur.INTRODUCTION With a focus on where water is used within the mineral processing, it has become evident that even though water is used in several different processes, majority of the water losses within the site occur at the tailings processing and the tailings storage facility. New tailings management technologies that can increase the recovery of water are actively being developed, but the key to improving the efficiency of water use and reducing the operational risks lies in closing the water loops and increasing the slurry density in the tailings processing. With this shift from conventional tailings technologies towards paste and dry stacking, water efficiency is vastly improved, but it might in turn lead to process water challenges with impurities, reagents and fines being recycled and accumulated within the production processes."

Jan 1, 2018

By Diego Canez Fernandes

O atual cenário mundial do mercado de carvões e da fabricação de aço vem estimulando mudanças no mix de carvões praticados na Usiminas. Neste contexto, foram realizadas alterações significativas no mix, com destaque para o aumento da participação de carvões alto voláteis e coque verde de petróleo. A qualidade do coque foi mantida por meio de ajustes de parâmetros operacionais na britagem, aliados à adição de óleo na mistura. O objetivo desse trabalho é apresentar a evolução do consumo desses materiais e os resultados de qualidade do coque. Os resultados de qualidade do coque (DI15/150, CSR e CRI) não sofreram variações significativas com a elevação da participação dos carvões alto voláteis e coque verde de petróleo, mantendo-se dentro da faixa visada.

Aug 1, 2018