Search Documents

By Edwin F. Shorey, Richard F. Coon, Steven B. Fradkin

Crosstown Interceptor Phase IA is the first deep tunnel element of the Milwaukee Inline Project. The tunnel contract includes 6,492 meters (m) of 9.1-m-diameter tunnel, two access shafts, and partial lining for structural purposes. The work also includes grouting to be performed as directed by the engineer to provide groundwater infiltration control in lined and unlined reaches of the tunnel. This paper summarizes infiltration observations, progress of the grouting work, and its potential application to the remainder of the Milwaukee project.

Jan 1, 1987

The commercial application of electrolysis to zinc sulphate solutions for the production of metallic zinc is a development ·of the past twenty years. Earlier attempts failed to give satisfactory results, chiefly because certain harmful elements were either not recognised as being present in the solution, or, if recognised, suitable methods of removal had not been developed. The electrodeposition of zinc from zinc sulphate solution is extremely sensitive to the influence of a great many factors, all of which appear to be closely inter-related.Some of these factors tend to minimise the necessity for a high degree of purity of the solution, while other factors aggravate the harmful nature of certain impurities.The relationship existing betweBn the various factors in zinc electrolysis makes a general discussion of the injurious effect of impurities very difficult since, under one set of conditions a given concentration of an impurity may be of minor: importance, where its under another set of conditions the same concentration of that impurity may prove dangerous to successful electrolysis.

Jan 1, 1934

The Menominee Range of northern Michigan was a major producer of direct shipping iron ore for nearly a century. When the last underground mine on the Range ceased operation in 1978, it marked the end of an era. For since the start of mining in the early 1880's the district has gone through a Lull cycle from the start-up of mining through close-down. During this period over 200 million long tons of iron ore were produced and shipped from nearly 100 mining operations. This development and production spanned the time from when the United States advanced from an essentially rural-agriculatural society through the industrial revolution and into the beginnings of the computer and space age. There are many lessons that can be learned from such a rich history. This report attempts to provide ouch a lesson. Through the use of case histories, deficiencies in past mining practices and mine closure procedures that have resulted in current mine related problems are documented. These problems -an be grouped into three areas; 1) subsidence 2) hydrological or drainage problems and 3) problems related to inadequate mine shaft sealing and capping practices.

Jan 1, 1983

By J. B. Forrester

In the operation of the coal mines in Utah few adverse conditions confront us. Physical conditions for the economical extraction of the coal are as near perfect as it is possible for them to be. Still several obstacles are encountered to keep up our interest and prevent us from getting in a rut. Of these I shall speak only of Burning, Wants, and Sluffing of Ribs. Should one travel the outcrop from Ivy Creek in Emery county to the Utah-Colorado line, there would be one outstanding feature indelible impressed upon one's mind. That feature is the omnipresent indications of burning in place. Viewing the eastern escarpment of the Wasatch Plateau from a distance, many splotches of dark red are plainly seen always lying above the coal floor. This stratum is a felspathic sandstone, appearing as a white line running the full length of the above escarpment and about midway between the floor of the valley and the top of the plateau. The coal bearing complex consists of shales, sandstones and coal. This complex varies from two hundred to eleven hundred feet in thickness. The number of coal seams are exceedingly variable. As a rule the argilutites form the bulk of this complex. This material is baked by the burning of the coal and the iron present is oxidized to the ferric state, coloring the shale to a dark red. This baked material forms a shingle tales that in places cover the entire complex. It is natural to expect that the most extensive burning is in the canyons facing to the south and east and on the south slopes of the ridges running to the east or west. Such, indeed, is the case. Still in this arid region many crop fires have existed upon the north slopes, especially in those canyons that face to the east. In fact today, instances are not rare where grassy north slopes, heavily timbered with balsam and fir that have attained a diameter of 14 to 24 inches, are found growing upon the disintegrated baked shingle and later development proves that the coal has been burned at least 500 feet back from the outcrop. Still these conditions are not normal. In this arid climate the south and east exposures are steep and barren, except for the scrub pine, cedar, mahogany and kindred semixerophytes. Bunch grass is also a lover of such exposures. There is very little soil found in such places; it is either blown away as fast as formed or washed away by the rare torrential rains, or the rapidly melting snow. Thus we see that the physical conditions are favorable for the starting and maintainence of outcrop fires. This brings us to the probable origin of this phenomenon. There are four probable ways' that such fires, could be started, namely:

Jan 1, 1921

By S. Weiss, E. Espinoza

The El Sauzal gold-silver deposit is a high-sulfidation, epithermal precious-metals deposit hosted by an east-dipping sequence of dacitic and rhyolitic pyroclastic and debris-flow units of probable Oligocene age. Total gold production since startup in late 2004 is approximately 450,000 oz. of gold. Above the sulfide boundary gold is mainly disseminated as small grains interstitial to alunite, kaolinite and quartz. The majority of the ore is found in quartz-alunite-kaolinite altered rock that mantles tabular to irregular silicic cores of vuggy, residual quartz ±kaolinite ±dickite. Grade domains are modelled as subhorizontal to east and southeast-dipping. Higher-grade domains cut across alteration zones and also coincide with transitions from vuggy quartz to quartz-alunite-kaolinite. The highest grades are commonly found marginal to vuggy quartz in transitional, hematite-rich quartz-kaolinite and quartz-alunite-kaolinite rock.

Jan 1, 2007

By C. J. Badenhorst

Oxides of sulphur are corrosive and are produced when sulphur-containing fuels are burned. Sulphur dioxide (SO2) is a colourless gas with a characteristic, irritating, pungent odour. Exposure routes to the human body are mainly through inhalation and skin and/or eye contact. Symptoms of exposure to SO2 may include irritation of the eyes, nose, and throat; rhinorrhea (discharge of thin nasal mucous); choking; cough; and reflex bronchoconstriction. To protect employees against the ill health effects of SO2 exposure, they are often required to make use of respiratory protection whenever entering areas were the SO2 levels exceed the statutory limits. The use of respiratory protective equipment should always be a last resort and should be considered only after other control measures have failed to reduce occupational exposure levels to below the occupational exposure limit or whilst other control measures are being investigated or implemented. Whenever the use of respiratory protection equipment is considered, it should always be used as part of a comprehensive respiratory protection plan. It is also extremely important that all potentially exposed persons are adequately and comprehensively informed and trained.

Jan 1, 2007

By P. Botane, A. Cailleau

"Compagnie Miniere Esperance operates a gold primary ore body. The ore is processed through crushing, grinding and gravity concentration generating tailings with remaining fine gold. Analyses of the tailings proved a residual gold grade sufficient for a chemical treatment.As lab tests proved the technical feasibility of a pre-concentration using flotation, an on-site pilot operation has been carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for the industrial circuit sizing.Data collected during the pilot campaign have been used for calibrating a process simulator built with the USIM™ PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain a good fine gold recovery in a small amount of concentrate. A preliminary capital cost has been achieved to assess the flotation workshop profitability.INTRODUCTIONCompagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation in two stages: a top plant and a bottom plant. A “coarse” pond contains tailings of the top plant; this product feeds the bottom plant. Tailings of the bottom plant are stored in the “fine” pond.Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and meteorological conditions).It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility."

Jan 1, 2009

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of “but which formula is the right one?” The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: • Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) • Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) • Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which

By Qi Wang, Zengzhu Kang, Jianguo Liu, Guanglei Liu

"Due to the increase of automotive vehicles, available parking spaces become a new type of limited resource in central cities of China, especially in those old districts without visionary urban planning. Additional mechanical parking in underground space is an efficient solution to provide parking spaces under the situation where the urban space is constrained. Shichahai district is an old protected zone in Beijing which is close to the Forbidden City and there are many Hutong (alleyway) and Quadrangles (courtyard house). No spaces are available for car parking on the ground and all vehicles are parking in Hutong without order currently. The local government plan to do renovation work for this district and improve the residential environment. Several innovative solutions are studied including parking in deep shafts, parking under existing buildings by under-pinned method, parking under buildings by covered excavation method, parking under roads built together with utility tunnel etc. 5000 difference types underground parking spaces are planned to be constructed in the following three years. Project examples are also introduced in this paper. INTRODUCTIONCar parking resources are very limited in central cities, especially in old districts without planning for increasing automotive vehicle volume. Traffic get worse when cars park on the side of the roads or move slowly to find parking spaces. Investigation shows the normal (parking space/ automotive vehicle volume) ratio is about 1.2 in most big cities such as New York, Tokyo and Hong Kong, while this ratio is only 0.5 in Beijing. One solution is to move cars out of central cities. But there are still huge parking requirements for the citizens living in central cities. Shichahai district is an historic protected zone in Beijing which is close to the Forbidden City and there are many Hutong and Quadrangles (refer to Figure 1 for project location). No spaces are available for car parking on ground and all vehicles are parked in Hutong without order currently. The local government had a plan to do renovation work of this district and improve the residence environment. 5000 different types of underground parking spaces are planned to be constructed in the following three years. One project designed and to be constructed by Zhongyan Technology will be introduced in this paper. Other innovative solutions will be introduced briefly as well."

Jan 1, 2017

By J. P. Landriault, F. W. Harrison

"Zinc-iron alloy coatings can be produced by either thermally alloying hot-dipped galvanized steel or by electro deposition. Stelco Inc. produces a thermally alloyed Zn-Fe alloy-coated steel, which is mechanically wiped to remove free zinc.A more extensive use of Zn-Fe alloy-coated steel has been predicted for unexposed autobody and structural part applications, since this material is characterized by good spot weldability and formability, and provides superior corrosion resistance under automotive primers.This investigation has examined the coating composition, corrosion resistance, spot weldability and formability of Stelco&apos;s Zn-Fe alloy-coated steel and found its properties to be similar to those of Zn-Fe alloy-coated steel produced by post coating annealing.IntroductionRecently, there has been increased automotive interest in galvanneal, which is characterized by good spot weldability, good paintabilityt and good corrosion resistance when primed. Stelco produces a thermally alloyed zinc-iron coated sheet product similar to galvanneal. However, this product is produced by mechanically wiping the free zinc from the surface of hotdip galvanize to expose the underlying zinc-iron alloy.The surface of Stelco zinc-iron alloy-coated sheet is matte gray and has longitudinal streaks which result from contact with Kevlar wipers during production (Fig. I). This paper describes the coating composition, corrosion resistance, weldability, formability and surface appearance of Stelco zinc iron alloy coatings and, wherever possible, compares these properties to those of galvanneal."

Jan 1, 1987

Abrasivity and wear resistance are not intrinsic properties of materials, but rather parameters describing the interaction between the wear part and the material exerting the wearing action. Moreover, wear or, at least, that part of the wear which is due to the cumulative effect of minute scratches, is linked to the hardness disparity concept. Abrasivity, in this context, is a relative concept, pertaining to a metal-rock pair, rather than to a rock. Based on this assumption, a methodology has been developed and checked against actual cases, enabling description of the abrasiveness of a rock or the abrasion resistance of a metal through the ratio of comparable quantitative indicators. The paper describes the methods and provides examples of applications to practical cases (namely: rock cutting, excavation by means of tunnel boring machines (TBMs), rock crushing, and hydro-mill cutting).

Jan 1, 2012

By C. J. A. Mcewan, C. M. Rice

The Rosita Hills contain rich, vein- and breccia pipe-hosted precious metal deposits. Volcanic activity occurred in two cycles - an early, mainly andesitic cone-building phase that terminated in the formation of a caldera and breccia pipes and a later phase characterised by trachytic lavas and dykes, rhyolite domes and lamprophyre dykes. Alteration consists of weak propylitic and argillic and, locally, intense advanced argillic, K-feldspar sericitic and silicic types. Marked trace-element depletions (Rb, Sr, Zn, Mn) are associated with K-feldspar-sericitic alteration and with advanced argillic alterations, whereas enrichments (Pb, Ag) are associated with K-feldspar-sericitic alteration. Gold distribution is highly localised and is controlled by breccia pipes and a caldera ring fault; it is not related to district scale alteration. In general, the geochemical and alteration patterns are complex, but they are clearly influenced by linear structures, the caldera ring fault and breccia pipes. Pipe-hosted Au-Ag and vein-hosted Ag mineralisation are associated, respectively, with early andesitic and late, post-caldera rhyolitic activity. The pipe-hosted and, especially, the vein-hosted mineralisation show affinities with adularia-sericite-type epithermal deposits

Jan 1, 1991

By John P. Coughlin

The Bureau of fines has tested a portable microseismic processor recorder at the Galena Mine, Wallace, ID, both in an environmentally controlled enclosure and, with minimal protection, in a working area of the mine. In both trials the device demonstrated effective and reliable data acquisition capabilities.

Jan 1, 1985

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By E McLean

The decision making check-list and hierarchy of information for process and plant design is generally wide-ranging and complex. The nature of grades, mineralisation and ore types in an ore body, its mine development sequence, and the body of results from metallurgical and physical test work present complex and competing influences on flowsheet development, values for design, equipment selection, plant efficiencies and operating strategy. The challenge is how to manage all these variables, to understand their impacts on performance, and how best to provide a cost-effective plant design and robust process that meets daily/weekly/monthly operating objectives. Throughput, production and grade or product specifications need to be met. The ore body is not average; its range of metallurgical and physical characteristics may be moderately to highly variable. This paper assesses some of the key competing influences and conflicting issues in design and equipment selection, and their effect on production and performance expectations.

Aug 8, 2011

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 120 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257; 7267,`7273; 7285, 7292, 7303, 7310, and 7324. 1. GRAVITATIONAL METHODS 7933. Ansel, E. A Eine Untersuchung zum Problem der Isostasie (An Investigation Regarding the Problem of Isostasy). Gerlands Beitr. Geophys., Leipzig, vol. 59, 1942, pp. 16-26.

Jan 1, 1945

By Nelson Rivera

El presente texto analiza la crisis económica y su relación con el Banco Minero. Para ello, se revisa las dos últimas recesiones económicas que tuvo el Banco entre 1975 y 1982, donde la crisis se agudizó por una caída en los precios de los metales y una inflación de costos que no pudo ser transmitida al precio de venta. Como consecuencia de ello, las empresas mineras que tuvieron préstamos, acusaron pérdidas en sus ejercicios e incumplieron en el pago de sus obligaciones. Como medida anti-crisis, el Banco Minero estableció comisiones de alto nivel para evaluar las situaciones y recomendar la dación de dispositivos legales que permitieron asistir a los Pequeños y Medianos mineros en la restitución de liquidez mediante préstamos sobre liquidaciones a precios deprimidos, Asimismo, generó la consolidación, refinanciación y moratoria de los clientes que estaban en suspensión de pagos de las obligaciones contraídas con el Banco Minero y la creación de líneas de crédito especiales para la Pequeña Minería.

Mar 1, 1985

The success of smooth blasting essentially depends on geological condition of rock. Also, in the perimeter hole, borehole pressures with light, well-distributed explosive loads are important to minimise overbreak. In order to simulate perimeter holes with scaled model test, the borehole pressure was considered as a factor of scale. Hydraulic oil pressure is applied as borehole pressure instead of using explosives and detonators in order to remove the undesirable effects of detonators in an experimental set-up of just two perimeter holes in a tunnel blast. The borehole pressure on a perimeter hole is nearly reproduced with hydraulic pressure which is generated by non-electric detonators in the hermetical cylinder.

Dec 6, 2010

By D Porta, E Grigolato, K Behrens

################

Aug 12, 2013

By John Zeni

In Australia during the 1990s, Zeni Drilling took on several demanding shaft boring contracts. This paper describes the safety, operational, technical and environmental advantages derived through the implementation of mechanized boring methods for two of these projects. The paper first describes a 3-meter (10 ft) diameter access shaft blind bored from an underground location to 440 meters (1,444 ft) deep for a gold mine in Tasmania. The construction of a 5.8-meter (19 ft) diameter, 515-meter (1,690 ft)deep ventilation shaft for a longwall coal mine in New South Wales is also described.

Jan 1, 2001