Search Documents

By E. A. Holbrook

The data in this bulletin were obtained during an investigation of screening practice by the University of Illinois engineering experiment station and the United States Bureau of Mines under a cooperative agreement between them and the State of Illinois Geological Survey Division. Earlier work on this subject includes a study of the general practice of coal preparation in Illinois, made in 1914 and published in 1916,1 and an investigation of Illinois coal-washing methods, results of which were published in 1912 in a bulletin 2 that contained complete information on the methods then in use for sizing washed coal. OBJECTS OF THE INVESTIGATION The present investigation was limited to a study of screening as applied in preparing mineral products with the expectation of obtaining more comprehensive information on screening machinery.

Jan 1, 1925

By R. E. Brewwe

"INTRODUCTION Anyone who has had frequent occasion to compare methods of analysis and testing as employed in European countries with those used in the United States has felt the need of a table or graph giving the relationship between the units of measurement of finely powdered materials. Most of the few published comparisons include only two series of sieves and often require tedious interpolations to adapt the data of one series to the series more familiar to the reader. To eliminate such deficiencies, the author hopes that the discussion and comparison of fine-series sieve sizes presented here will conserve the time of interested research workers.ACKNOWLEDGMENTSThe author is deeply indebted to Virginia B. Strathearn, scientific aide, for help in compiling the information from the literature and to W. A. Solvig, senior chemist, for valuable suggestions in preparing the manuscript.SQUARE-MESH-SIEVE SERIES OF DIFFERENT COUNTRIESSieving analyses of powdered materials have been placed on a comparable basis in different countries by the introduction and adoption of standard sieve-scale series. Series of wire-cloth square-mesh sieves in common I oratory and industrial use include: Institution of Mining and Metallurgy standard laboratory screens (I.M.M.); British Standards Institution standard for fine-mesh test sieves (B.S. or B.S.I.); Tyler standard sereer-scale sieves; United States standard sieve series; Deutsche Industrial-Nermen (DIN); and the standard control sieves of the Association Francaise de Normalisation (AFNOR). With the exception of the I.M.M. series in which the opening is equal to the diameter of the wire, the general proportions of the various series of sieves are similar. The size of British and American sieves is designated by the number of meshes or openings per linear inch or, more recently, by the number of microns per linear sieve opening. In a technical sense the word ""mesh"" is meaningless, unless the diameter of the wire is also given, so that the size of the opening can be determined. On the Continent sieves are designated either by the nunber of Mesh per linear centimeter or by the number of openings per square centimeter."

Jul 1, 1944

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By John Paul Gries

This Bureau of Mines study outlines the history of 11 major metal ore deposits or districts that are relatively new discoveries. The oldest operation is the White Pine mine, where major exploration was initiated in 1929. Discovery (delineation of ore bodies) dates range from 1948 to 1976. All but two of the deposits, Quartz Hill in Alaska and Flambeau in Wisconsin, are or shortly will be in major production.

Jan 1, 1979

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.

By Jon Huff, Jeffrey Donville, Hannah Iezzoni, Dan Stevenson

Occasionally, in the design of deep foundations for a structure, a single deep foundation element may be used to support a building column. The most common type of element used in such cases is a drilled shaft (also referred to as a drilled pier, caisson, or bored pile). However, as installation capabilities have improved, large diameter augercast piles are increasingly more common. While drilled shafts and augercast piles differ significantly in construction methods, in the eyes of the International Building Code (IBC), both are treated as cast-in-place deep foundations and must comply with many of the same code provisions. Deep foundations are required to be braced such that lateral stability is provided in all directions, however isolated, cast-in-place elements that have a diameter (D) of at least 2-feet and a length (L) not more than 12 times the diameter can be an exception. In response to the concerns raised by some member professionals, the Deep Foundations Institute’s (DFI) Augered Cast-in-Place Pile and Drilled Displacement Pile Committee took a closer look at the code and its applications, the historical development of the code language through the years and performed analytical modeling to evaluate the impact of this ratio on a pile’s stability. The question is whether the limiting ratio included in the IBC 2018 code provisions is justified, or whether different criteria should be used to determine when isolated deep foundation members are allowed.

Sep 8, 2021

By F. E. Armstrong

This report describes development and application by the Bureau of Mines of techniques and instruments for using radioactive inert-gas tracers to determine flow paths through petroleum reservoirs that have natural fracture systems and for which water injection has been selected as the stimulative production method. A field test was made to prove the techniques and evaluate instrumentation. The feasibility of applying the techniques and instruments to the solution of reservoir problems in other stimulative methods of production also is discussed. Oil commonly is displaced from sandstone host rocks by the action of a driving force that causes the oil to move through interstices of the rock and into production wells. In addition to the requirements of oil being trapped within the sand pores and the presence of an effective displacement mechanism, the rock itself must have adequate permeability to permit flow of oil and other fluids.

Jan 1, 1961

By D. W. Alexander

Researchers from the U.S. Office of Mine Safety and Health Research (OMSHR) of the U.S. National Institute for Occupational Safety and Health (NIOSH) completed field trials during coal mine rescue contests using simulated gas detectors in place of placards. The gas monitor simulator (GMS) devices replaced static, paper placards to deliver gas concentration data. Eleven teams were observed during the field contest, which was approved by the Mine Safety and Health Administration (MSHA). GMS devices were given to three team members (the captain and both gasmen). Observation of teams revealed that team members changed behavior by acknowledging and sharing information more often while using the GMS. As a result of this research, it has been demonstrated that under the existing contest format, the newly developed GMS device may be used with no adverse impact on team contest performance. Furthermore, when GMS technology advantages are used, contest realism is improved. In the future, competency assessment may be incorporated.

Jan 1, 2012

By Thomas P. Mucho, Thomas M. Barczak, Dennis R. Dolinar

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial-and-error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground reaction behavior based on support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health's (NIOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate application of alternative roof support systems or to design in-mine trials so that a fair and equitable comparison of different support systems can be made. A case study of the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to the conventional wood and concrete cribbing historically used at this particular mine.

Jan 10, 2000

By K. Biswas, F. C. Felipe

Paste backfill, because of its colloidal or water-holding properties, does not produce run-off water when placed underground. Paste backfill is generally, prepared from relatively low water content, full mill tailings with a certain proportion of ultra-fine particles and mixed with cement, thus producing early and better strength. Mill plant discharge tailings and other materials available at or near the mine site such as sand, aggregates or waste rock are used as blending materials in the mix design. This study investigates the influence of the above-mentioned blending materials on the mechanical characteristics of paste backfill, as well as the grading, shape, specific surface area, mineralogy and workability of the different mix design.

Jan 1, 2000

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By W. D. Striffler

Land disturbed by surface mining in Colorado and other western states has increased substantially over the past several years and is likely to increase even more in the future. This study was initiated to provide basic information on hydrologic and erosional characteristics of regraded coal spoils in Colorado as an aid for planning future reclamation activities. Eleven of twenty-one surface mines licensed in Colorado were sampled during the summer of 1980 and 1981. Mines not sampled included mines which had not progressed to the point that reclamation had begun, and mines where operators denied permission to sample. All coal regions were sampled with the exception of the San Juan Coal Field. Physical and hydrologic characteristics of regraded coal spoils in Colorado were determined using standard field and laboratory procedures. Field sampling included characterization of sites (slope, vegetation density, proportion of surface rock, bare soil, etc.) and infiltration measurements using a l-meter square drop former raining on a 1/2 square meter rectangular plot frame. Core samples collected in the field were analyzed for saturated hydraulic conductivity, bulk density, organic matter, moisture retention and texture. The erosion potential of each site was determined using the Universal Soil Loss Equation (USLE). Results of the sampling indicate that infiltration rates vary widely both within and between sites. However, definite trends with respect to coal fields are apparent. For example, the Green River (Yampa) coal region had a wide range of sampled infiltration rates (1.2 to 5.1 cm/hr). However, most of the sites clustered towards the low end of the range. The North Park (Marr Strip) also was rated at the low end of the infiltration range (2.0 to 3.0 cm/hr). Average infiltration rates for the Canon City and Uinta Coal Regions were at the high end of the range (4.9 to 5.5 cm/hr). Multiple correlation analysis of infiltration rates vs. site characteristics showed that infiltration rates were most closely correlated with the depth of wetting, the amount of mulch cover, and site slope. The depth of wetting was highly correlated with the depth of the topsoil and the bulk density of the spoil. In general, the topsoil at all sites appeared to be highly permeable to water intake but once saturated, subsequent infiltration depended upon characteristics of the underlying spoil. Vegetation cover affected infiltration on individual mine sites but was not as pronounced as topsoil characteristics or mulch. Erodibility of topsoil and spoils, as determined by Wischmeier's "K" factor, ranged from 1.34 to 0.56 tonnes/ha. (topsoil) and 1.25 to 0.66 tonnes/ha. (spoils). Definite trends in erodibility are evident. The Green River (Yampa) Coal Region displayed consistently higher erodibilities (1.34 to 0.75 tonnes/ha.) than other coal fields (0.72 to 0.56 tonnes/ha). Lowest erodibilities were observed in the Uinta, North Park, and Raton Mesa Coal Regions (0.56 to 0.62 tonnes/ha). Erodibilities of underlying spoils showed similar trends as the topsoils. Erosion potential (the product of soil erodibility and rainfall erosivity) was detennined using calculated ?K? factors and rainfall erosivities (R) taken from Clyde (1976). Results show that the Delagua coal field, Raton Mesa Coal Region had the greatest erosion potential due to the high rainfall energies in the region, while the North Park and Uinta Coal Regions had the lowest potential erosion.

Jan 1, 1981

By A. J. Stewart, M. Guay, J. W. Critchfield, A. P. Hoddeson

The MetroWest Water Supply Tunnel project includes three main work shafts, excavated primarily in rock. Shaft L is 9.8 m (32 ft) diameter and 124.1 m (407 ft)deep. Shaft E is 7.0 by 12.8 m (23 by 42 ft) and 91.4 m (300 ft) deep. Shaft 5A is 7.9m (26 ft) diameter and 72.5 m (238 ft) deep. Construction methods are compared and contrasted. Lessons learned involve a differing site condition in soil overburden, contractor-proposed modifications, and remedial slurry wall work. Other aspects discussed include noise and vibration control, groundwater inflow, water treatment, muck handling and contract administration issues.

Jan 1, 1999

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

By Yaw Boadi, Andrew McCallum, Sandy Gray, Yavuz Atasoy, Peter Wemyss

"Various full-scale test programs and installations of the InLine Pressure Jig (IPJ) have provided evidence that pre-concentration of the difficult to leach sulphide mineral through gravity can provide significant increases in economic recoveries. The continuous gravity concentrates are intensively treated either by re-grinding or Intensive Cyanidation. Data from various mine sites worldwide is presented. Treatment of complex ore bodies with this low cost methodology may render previously uneconomic ore bodies financially viable and assist in the recovery profile of transitional ore.INTRODUCTIONThe use of gravity is made extremely attractive in complex ore situations due to the low cost of operation, typically a few cents per ton operating cost and lack of chemicals.Gold mines which suffer from poor recovery due to complex mineralogy such as Stibnite, Arsenic, Carbon, Telluride, Silver and other pacifying agents such as Iron, which can form coatings, can all benefit from the process proposed in this paper. The key issue is not overall recovery as much as one of economic recovery. The key to this is maximised recovery at the lowest possible capital and operating cost. Other options such as flotation are reviewed but are not seen in many instances to be the panacea due to issues discussed in the paper. The use of the InLine Pressure Jig in the re-circulating load of the milling circuit is a cost effective means of recovering a sulphide/gold concentrate containing the complex mineral assemblages which require re-grinding and intensive leaching for optimised gold recovery.The benefits of Jig Assisted Grinding (JAG) are many and the challenge over the past years has been developing, understanding, implementing and evaluating the benefits of various flowsheet models. This has involved the reconciliation of results in plant scale trials back to the original laboratory test program. The following paper outlines the insights gained in this area through extensive work carried out by many people across both laboratories and plant sites in Australia and overseas. The examples in this paper are some of the work carried out on a few selected sites but similar work has been carried out on other sites such as Penjom, Granny Smith and Agnew. This work has eventuated in several installations which we believe have great importance in the future of the gold processing industry. They will lead the way forward to the modern all-gravity plants of the future.Compared to flotation, for the recovery of sulphides, gravity is a simple option. The simplicity generally translates to low capital and operating cost."

Jan 1, 2004

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By H. A. Steane

"This presentation will cover some crushing and grinding considerations in plant design and operation. There is nothing basically new in the subject matter presented here; however, the viewpoint and interpretation may be novel and some of it controversial.The presentation is based on experience gained in the metallurgical design of plants for Placer Development Limited from 1960 to the present. The plants are listed on SLIDE No. 1.These plants have conventional crushing, followed by rod mill and ball mill grinding. I would like to think that autogenous grinding plants are the answer for eliminating secondary crushing plants and reducing the capital and operating costs; however, the autogenous plants seem to have some problems of their own and I have had no experience with them.Fineness of Grinding RequiredFirst let us consider the fineness of grinding required.The fineness of grind will affect the recovery obtained, and the relationship must be determined. If the grinding is too coarse, some of the valuable mineral, either free or locked in middling grains, will not be floated. However, as grinding is probably the greatest single operating cost, we do not want to grind any finer than is justified economically.Finer grinding should not be carried beyond the point where the net smelter return for the increment saved becomes less than the added operating cost. Even this fineness will be beyond the economic limit because of the additional capital cost for the equipment needed to achieve it. These factors will be discussed in more detail later.The Bond work index is the commonest method of expressing a measure of the effort that has to be expended in grinding. It is the kilowatt-hours required to reduce a ton of rock from an infinite size to 80% passing 100 microns. The formula allows a calculation to be made for other size ranges."

Jan 1, 1976

By T. Chong, R. Pesalj, B. Marchant, Z. Nikic

"The Mount Polley copper/gold project is located in central British Columbia and is currently being developed by Imperial Metals Corporation. Extensive laboratory and pilot plant testing was required to develop acceptable metallurgy for recovery of both sulphide and oxide copper-gold mineralization. Copper recovery is highly sensitive to oxide copper content of the feed whereas gold is primarily associated with the copper sulphide minerals. A conventional flowsheet where sulphide flotation is followed by sulphidization and oxide scavenging is described. The conventional flowsheet was used in a feasibility study which resulted in a favourable production decision at Mount Polley. Detailed engineering and permitting are in progress.More recently, laboratory and pilot testing of a new flotation reagent, S-6493*, an oxide specific collector, has indicated that improved copper recovery can be accomplished with reduced reagent consumption, including elimination of the sulphidization step, using S-6493 compared with the conventional flowsheet. The comparative metallurgical results using S-6493 and conventional sulphidization methods are presented, from both bench scale and pilot testing. Comparative economics of the conventional flowsheet and that using S-6493 are also presented. Advantages of S-6493 include reduced reagent costs, increased revenues from additional copper recovery, and overall reduction in capital and plant operating costs due to the simplified flowsheet. INTRODUCDONThe Mount Polley copper/gold property is located in Central British Columbia, 56 air kilometres northeast of Williams Lake. The first recorded exploration was in 1964. By 1989, a total of 238 diamond drill holes, totalling 27, 522 meters, was completed to detail reserves on the Mount Polley prospect. A number of drill core composites were submitted, containing a variety of oxide copper levels, for metallurgical flowsheet development. Six bulk samples were collected from surface trenches for additional bench scale testing and for pilot plant testing."

Jan 1, 1991