Search Documents

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

By H. U. Ross

"INTRODUCTION Extensive studies have been carried on pure gold to determine the various factors that affect its dissolution in alkaline cyanide solutions. With the extension of milling to refractory ores more intensive investigations on the effect of impurities in the ore on the dissolution kinetics are needed. The present work describes experiments carried on refractory flotation tailings with the object to determine how the recovery of gold could be increased. The effect of arsenic and antimony in the ore and the excessive use of lime are discussed. Control of cyanide losses is also dealt with.MECHANISM OF THE GOLD DISSOLUTION REACTION In aqueous cyanide solutions, gold is believed to be dissolved by one of the following reactions:4Au + 8NaCN + O2 + 2H20 = 4NaAu (CN)2 + 4NaOH (1)2Au + 4NaCN + 2 + 2H20 = 2NaAu (CN)2 + 2NaOH + H202 (2)2Au + 4NaCN + H202 = 2NaAu (CN)2 + 2NaOH (3) The first of these, known as the Elsner Equation is supported by )4 3,2,1(several authors while others(5,6) support reactions 2 and 3 known as the Bodlander Equations. According to Habashi(7), the overall reaction for the dissolution process is as shown in equation 2. Most of the workers agree that hydrogen peroxide is produced in the course of the reaction."

Jan 1, 1973

By C. S. Kucukkaragoz

An ilmenite concentrate was reduced in the solid state with carbon under argon atmosphere at temperatures between 1000oC and 1400oC. The ilmenite concentrate and 50% excess carbon were reacted to achieve the highest attainable degree of reduction at each temperature and the reaction products were subjected to a series of analytical work by optical microscopy, X-ray diffraction analysis and SEM ( EDS) analysis. The ilmenite remained unaltered at 1000oC and had a slight change in its composition at 1050oC. A secondary oxide phase containing metallic nuclei was detectable at 12% reduction at 1100oC. The reduction of TixOy took place in a sequence changing the y/x ratio from 2.0 to a value less than 1.0 at 84% reduction at 1400oC. Metallic phase consisted of Fe and C initially and started to include Ti at the later stages. Complete reduction of TixOy to metallic Ti was not possible at these temperatures.

Jan 1, 2005

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

By S. R. Zimmerley

As a result of the drilling program of the :Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By S. R. Zimmerley

As a result of the drilling program of the Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By VÍCTOR VÁZQUEZ-VÁZQUEZ, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, JESÚS L. VALENZUELA-GARCÍA, OFELIA HERNÁNDEZ-NEGRETE

This study examines a process for the recovery of precious metals from difficult minerals that exhibit refractory characteristics to cyanidation: low extraction of metals and high consumption of leaching reagent. A mineral sample from Monte del Favor Mine, located in Hostotipaquillo, Jalisco, Mexico, was physically and chemically characterized by X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), fire assay and atomic absorption spectroscopy (AAS). Two stages of leaching were carried out, first to eliminate manganese from the sample using sodium sulfite (Na2SO3) as a reductive reagent along with sulfuric acid (H2SO4), and second to dissolve gold and silver with hydrochloric acid (HCl) and sodium hypochlorite (NaClO). The results show extractions of around 96 percent for manganese (Mn), 98.73 percent for silver (Ag) and 83 percent for gold (Au). The usefulness of high acidity and Na2SO3 to obtain better results in Mn and Ag leaching are discussed along with the roles that HCl and NaClO play in Ag and Au dissolution values.

By Olaf Andersen

Crucible melt extraction yields short metal fibers with eqivalent diameters as low as 50 µm from almost arbitrary metals and alloys. Highly porous components can be made from such fibers by suitable deposition and sintering methods. This technology is being developed at the Dresden based Department of Powder Metallurgy and Composite Materials of the Fraunhofer Institute for Manufacturing and Advanced Materials (IFAM) and has been applied to gold alloys and iron-base alloys containing small additions of precious metals. From the manufactured gold fibers, sintered structures were made for decorative applications. Additionally, it was found that due to rapid solidification during the fiber formation, precious metals can be finely dispersed in ironchromium- aluminum (FeCrAl) and FeAl20 alloys. Good catalytic activity at elevated temperatures was found in compositions containing 3 wt.-% Ce and 0.5 wt.-% Pt.

Oct 1, 2003

By Rodney D. Lamond

The need for blast vibration monitoring can be attributed to a combination of three factors: Structural damage, Blast design and Human annoyance. Traditionally, vibration damage criteria are prescribed in terms of peak particle velocity (PPV), as measured or predicted in the ground surrounding a blast. The PPV in the vicinity of a blasthole is strongly influenced by the quantity of the explosive per delay. In general, the existing prediction models give reliable results but fall short of addressing the change in PPV when the charge is decoupled and/or distributed.

Jan 1, 1995

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

By Peter Reinders, Dirk Hummel

This paper describes a newly developed Surface Remote Blasting System (SURBS) for electronic detonators, which is currently being introduced into surface blasting applications. The rationale for developing the SURBS was to meet key needs of mine operations, such as minimizing the shutdown time and the capability to conveniently initiate blasts in difficult terrain from a safe distance. Increased distance from the blast site, combined with a good overview of the site enables maximum safety during blasting. The system also removes the inconvenience of running long firing cables. The SURBS consists of the field-proven detonator and equipment technology of an existing electronic detonator system, a Surface Remote Blasting Box and a Surface Remote Blaster. The Surface Remote Blaster is the Master unit and controls the Remote Blasting Box via encrypted radio communication using a sophisticated safety technology, which guarantees that the highest safety standards are maintained.

Jan 1, 2005

By P. J. Baguley

The model has been developed on the basis of the observation that the partitioning behaviour of a particle is related to its calculated terminal velocity. It utilises a theoretical calculation of the terminal velocity of each particle class. This is then correlated with the observed partition data for a plant separator using empirically-derived functions of operating conditions which take into account effects such as bath turbulence, holes in drum lifters and feed arrangements. The model successfully decouples the effects of medium density and viscosity and is appropriate for any bath-type separator. The correlation between calculated terminal velocity and actual partitioning behaviour was established and modelled using data obtained from two Wemco drums treating Fe and Mn ores. The model can be used to predict the prevailing size-by-size partition curves and the separation (product grades/recoveries) given the washability of the feed and operating conditions. Simulations are used to show that, for the treatment of Fe ore, there is a maximum medium density beyond which product grades fall and that this maximum decreases as the proportion of magnetite in the medium increases. This is attributed to the dominant effect of viscosity at higher medium solids concentrations

Jun 18, 1905

By James A. Bachmann, Christopher J. Gray

On December 26, 1994, at 1:00 am, Santa Fe Pacific Gold's Twin Creeks Mine experienced a major highwall failure involving over 2.5 million tons. The resulting effects of this slide were thousands of ounces of gold that were now deferred and an unstable wall above which made mining the slough material unsafe.

Jan 1, 1996

By J. J. Fritts, J. L. Patrick, T. L. Wright, C. O. Ensign, W. S. White, J. W. Trammell, J. C. Wright, D. J. Hathaway, R. J. Leone

The copper deposit at White Pine, Michigan, from which a little more than 5 per cent of United States primary copper currently is produced, is a large stratiform orebody, 4 to 25 feet thick and several miles across. The present ore column, containing about 1.2 per cent copper as chalcocite and native copper, is confined to the basal beds of the Nonesuch Shale. This upper Keweenawan (Upper Precambrian) formation is a distinctive gray siltstone unit, about 600 feet thick, overlying and overlain by thick red-bed sequences. All these rocks contain abundant volcanic debris, but the latest known igneous activity within 50 miles antedated the Nonesuch Shale. The rocks are unmetamorphosed and only moderately deformed, mainly by tilting and faults. Pyrite, presumably syngenetic, is the only prominent sulfide throughout most of the Nonesuch Shale. The basal beds of the formation, however, contain disseminated copper minerals instead of pyrite and constitute the cupriferous zone. On a regional scale, the top of the cupriferous zone cuts across bedding, and ranges from an inch or so above the base of the formation in some areas to more than 50 feet in others. However, within the cupriferous zone the distribution of copper shows remarkable stratigraphic control. Certain beds are copper-rich compared to the beds that lie between them and the differences persist throughout the White Pine region. Several darkgray thinly laminated beds in the lower 10 to 25 feet of the Nonesuch Shale are rich enough and sufficiently close enough together to constitute a mineable thickness where they lie within the cupriferous zone. Pyrite is the characteristic sulfide of the Nonesuch Shale as a whole. The principal sulfide mineral of the cupriferous zone at the base of the formation is chalcocite. The succession of minerals outward and upward from the center of the cupriferous zone is native copper-chalcocite-bornite-chalcopyrite- pyrite. The bornite and chalcopyrite are confined to a narrow fringe at the margin of the cupriferous zone. This pattern of mineral zones is believed to represent reaction between syngenetic pyrite and introduced copper. The main copper mineralization is independent of structure and apparently antedates deformation. Details of the geometry of the cupriferous zone indicate the possibility that copper was introduced from the underlying sandstone prior to lithification. The source of the mineralizing solutions and their copper is not known.

Jan 1, 1968

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952

By Jimmy Rodríguez Las Heras

Durante la explotación de los niveles inferiores en la mina Yauliyacu, se generaron dudas sobre la ubicación de las concentraciones de esfuerzos y sus relaciones con los estallidos de roca. En este sentido, se instala un sistema microsísmico donde mediante el análisis de la microsismicidad se elaboró los estándares que permitieron reducir los incidentes por estallidos de roca presente, así como la frecuencia, magnitud y daños a las personas, y equipo e infraestructura de mina, debido a la energía liberada por los eventos microsísmicos. Por ello, el presente trabajo señala los beneficios del uso del sistema de análisis de microsismicidad como la actualización contínua de la zonificación minera de acuerdo a la concentración de esfuerzos, procediendo al reforzamiento del sostenimiento como medida de prevención.

Sep 21, 2013

By Nural Kuyucak

Several thousand years ago, metallurgists discovered that by combining two relatively soft metals, copper and tin, they could make a new material, bronze, that was stronger than either metal separately. Bronze and other alloys show how different materials can be integrated to create something new and better. Today?s mining industry can likewise find benefit in an integrated approach to managing the external impacts it has through its waste materials and its use of water. Just as using bronze gave ancient nations an economic and military advantage, mining companies can gain competitive advantage through finding better ways to manage water and waste. Trends pushing this include: ? Environmental ? Regulations on water-taking and the quality of discharged water are becoming more stringent. Net zero discharge requirements are often imposed by regulators. Mining companies also come under pressure to manage environmental impacts of mine waste, including minimizing the area occupied by waste and seepage amount resulting from infiltration of water from a smaller surface area. ? Social ? Particularly in arid parts of the world, there are multiple possible uses for each gallon of water. Local residents do not want to see a reduction in supplies of water for agricultural, domestic, manufacturing and other purposes. They get suspicious about any potential impact of water being mixed with their water reservoirs if it comes from a mining site, even if it would be treated. Such suspicions may cause conflicts among the stake-holders and delays in project approval processes.

Jan 1, 2009

The Institute has prepared a list of Societies' publications, magazines, . etc., which were duplicates and were discarded at the time of the consolidation of the libraries of the three Founder Societies. These books will be disposed of about March 1, 1916 by the Board of Directors of the Institute through the Library Committee. If, meanwhile, members who have incomplete sets of these books, or for any other reason desire to secure some of them, they are asked to communicate immediately with the Secretary, as this is in unusual opportunity to secure books at a very low price. American Gas Light Journal, viols. 31 to 39. American Institute of Electrical Engineers, Transactions, vols. 5 to 26. American Machinist, vols. 3 to 20, 22 to 29. American Society of Civil Engineers, Transactions, vols. 2 to 10, 21 to 24, 26 to 33, 39 to 49, 52, 55, 58, 74. Index, viols. 1 to 21. American Society of Mechanical Engineers, Transactions, vols. 1 to 28. Index, vols. 1 to 20, vols. 1 to 25.

Jan 1, 1916

By Beardsmore G. R

Geothermal gradients in the Gippsland Basin commonly exceed 35¦ C/km. Consequently models of thermal maturation may indicate exploration targets with an anomalous age/depth distribution. However regional geothermal models are constrained primarily by observations of surface heat flow. High geothermal gradients may simply reflect the presence of low conductivity coal beds within the basin. Heat flow data are not readily available for the Gippsland Basin. Normally special purpose drill holes are required to provide direct determinations of surface heat flow. These provide core samples for thermal conductivity and allow measurements of a stable geothermal gradient at least one year after drilling. Different indirect procedures are now required to provide estimates for the Gippsland Basin. Bottom hole temperatures can be used with suitable corrections to provide an indication of the regional geothermal gradient. However the corresponding thermal conductivities are more difficult to determine. Geophysical logs can be used to detect the major lithologies but detailed statistical analysis is required for numerical estimates. Complex mixing models are now suggested for geothermal surveys linking physical properties to variations in the mineralogy of each well. Allowing for low conductivity coal measures the data in the Gippsland Basin suggest values for heat flow consistent with regional trends in Australia. Interpretation is complicated by overprinting of transient thermal events with different time scales. Apart from the tectonics of basin evolution geothermal signatures may be complicated by regional ground water migration, the 'hot spot' trace associated with southward younging of Cainozoic volcanism, diagenesis, and basin refraction.

Jan 1, 1992

By Jian Liu

The study aims to leach copper from a low-grade flotation middling by optimizing the leaching process using response surface methodology. The effect of key parameters, i.e., sulfuric acid concentration, nitric acid concentration and leaching time, on the leaching efficiency was investigated and a quadratic model was suggested by the methodology to correlate the variables to the efficiency. The results indicate that the model is in good agreement with the experimental data at a correlation coefficient (R2) of 0.97 and the most influential parameter on efficiency was identified as sulfuric acid concentration. The optimum conditions for copper leaching from the middling were identified as sulfuric acid concentration at 103.74 g/L, nitric acid concentration at 12.50 g/L and leaching time of 30.98 min; under such a condition, an average leaching efficiency of 93.16% was achieved from the middling.

Jan 1, 2011