Search Documents

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

Stope back conditions in the cut-and-fill stopes at New Broken Hill Consolidated Limited often deteriorate to such an extent that, because conventional rockbolts are not able to maintain safe working conditions, square-set timber is installed. An attempt to eliminate this costly procedure has involved the use of long grouted rockbolts using high tensile prestressing wire. These bolts were developed in conjunction with the prestressing engineers of BBR (Aust.). This form of support has improved the back conditions, maintained safe working conditions, and delayed the introduction of timber in a number of stopes.Production from these stopes has been maintained at its previous level (at a rate approximately double that of a comparable timber stope).

Jan 1, 1974

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By Whitmore R. L

The action of water on a number of Queensland shales which are associated with particular coal measures and oil shales has been studied. The results suggest that the disintegration of some of the shales could cause significant problems in mining and preparation operations. The extent of shale breakdown varies widely from deposit to deposit and from seam to seam but a suitable assessment procedure utilises the test described in AS 1661-1979, and an improved method of presenting the results is described in the paper.

Jan 1, 1982

By S. P. Godby, S. P. Sharples

Wind-tunnel tests were carried out of the conditions under which nuisance dust particles (100-1 000 micrometres) become entrained by wind. A laser entrainment monitoring system (LEMS) was used, and was found to provide an accurate means of assessing nuisance dust emissions from a surface. Accurate determination of the threshold entrainment velocity of dusts using the LEMS gives a baseline against which the performance of dust control techniques can be evaluated. Minerals tested included coal, petroleum coke, limestone, sand and pulverised fuel ash. Pilot field trials of a portable wind tunnel equipped with the LEMS have been successfully completed, providing a means of validating laboratory results in the field

Jun 19, 1905

By A. H. Burns

"Regenerative and recuperative burner systems require advanced combustion techniques to minimize NOx emissions. Various methods of pollutant minimization and furnace design considerations are described. Cited examples are a large high temperature furnace and a small Zinc vaporizing furnace. The concept of total carbon footprint is introduced. The application of Biomass combustion as an effective method of cost and green-house gas (GHG) reduction is discussed. Practical considerations of scale, location and process limitations are discussed. Two examples of biomass fired equipment are cited. Ideal sites have large biomass resources available locally. Processed biomass fuels will be an important substitute for fossil fuel. INTRODUCTIONIn 1992, I presented a paper entitled Combustion Strategies In The Modern Industrial Environment (1992). At that time an abundant supply of cheap fossil fuel made many of the measures I talked about difficult to justify for anything but new equipment.Since 1992 we, as a society, have demonstrated an ability to accelerate the pace of industrial and societal change. The term industrial revolution applied to this age of incessant change is completely meaningless, implying a discrete moment in historical time. What our society has built is a system capable of unfettered, continuous and accelerating technological change. With this change comes an increasing demand for energy and materials.This year is the anniversary of the Titanic disaster, a moment in time when technological certainty met the caprice of nature and gave us a brutal reminder of what can happen to us if we underestimate that power (Mowbray, 1912). In the intervening interval we have regained the technological arrogance that was lost in 1912 bringing us back to the problems of climate change and the need for sustainable industrial activities.We use advanced mathematics to describe many complex systems, sometimes with disastrous results. For example there has been a recent attempt to model the global economy as a completely deterministic system. This premise is flawed at its foundation as human nature and emotion are indeterminate constants in the equations, yielding probabilistic solutions at best. As engineers we are all familiar with stiff problems. The solution to such a problem is meaningless and we have all had the misfortune to live through and rue the effects of that miscalculation over the last few years."

Jan 1, 2012

By Martin D. Conyac

A 1984 Bureau of Mines investigation identified ho mineral resources in the Wilderness Study Area (WSA). However, four prospects in the WSA contain anomalous amounts of copper and silver minerals; one had traces of gold. Stratabound copper-silver occurrences appear to be prevalent. Quartz veins in the WSA locally contain trace gold, and one mine adjacent to the area produced some gold in the late 1800's. The WSA is underlain principally by Precambrian and early to middle Paleozoic quartzites, argillites, dolomites and limestones that have been complicated by faulting, generally tilted northeastward, and thrust southeastward over sequences of late Paleozoic sedimentary rocks. The stratabound copper-silver occurrences and gold-quartz veins are in Precambrian and Cambrian rocks in the western part of the WSA, as are similar deposits regionally. Sand and gravel, and limestone are abundant, but plentiful resources of these commodities are nearer established markets. In November 1983 there were 5 small groups of current claims oh the WSA boundary; none are patented claims. Probably less than 35 claims have been located within the WSA, mostly in the northwestern portion; hut over 100 claims have been located outside, near the northwestern boundary. Oil and gas leases nearly surround the boundary and 6 extend up to 1 mile into the study area. There has been no recorded mineral production from within the WSA. From 3 to 5 miles to the west, several lode nines in the Johnnie district have produced several million dollars worth of gold from quartz veins, and some silver and lead from galena-calcite veins. These veins generally trend northeasterly and dip northwesterly and probably do hot extend into the study area.

Jan 1, 1985

Electrical trailing cable used to power coal mining machinery is frequently damaged in usage because of tensile strain or crushing effect of mining machines running over the cable. One of the repair problems is finding the exact location of a short or open in this cable so it may be spliced or otherwise repaired. The U.S. Bureau of Mines and FMC corporation signed Contract No. H0 122011 in August, 1971, to develop instrumentation for finding faults in coal mine trailing cable. This report describes performance of several existing instruments as trailing cable fault locators and also construction details and performance records of several cable fault location instruments that FMC designed, built and tested as part of this project.

Jan 1, 1973

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By Clayton R. Morlock

Airblasts have been monitored at four coal strip mines and at a limestone quarry. Thirty-seven production blasts have been monitored with three seismographs, resulting in one hundred and eleven complete air pressure records. Instrumentation selection use is described. Data analysis includes an assessment of the predictability of peak overpressures by means of the cube root scaled distance law. It is found that predictability for the cases studied here is not good. An extensive discussion of possible explanations is included. A detailed analysis of the frequency content of the observed airblasts, of considerable importance in evaluating potential annoyance problems, has been made for all records. A computer program has been written to simulate airblasts induced by multiple-hole blasts. A series of small experimental blasts have been detonated and monitored in order to allow an assessment of the program. It is clear that airblasts, especially when induced by very small charges and monitored at very close distances, are highly sensitive to detonation times. Retrofitting of airblast records occasionally was possible, but considerably improved field work is required to validate or refute the computer model.

Jan 1, 1983

By A. J. Van Der Merwe, J. F. Erasmus

One of the valuation approaches applied to Advanced Exploration Areas and Pre-Development Projects is the so-called ?in situ Mineralization Method? or the ?Yardstick Method?. This method is based on the concept of a known undeveloped Mineral Resource being worth a certain fraction (the ?Yardstick?) of the contained commodity value (?metal in ground?), using commodity prices ruling at the date of valuation. The Yardstick value is derived usually from an average market-based figure obtained from an analysis of recent transactions and is expressed as a monetary value per ounce or per tonne. It maybe modified to accommodate the quality (e.g. grade) and category (e.g. confidence level) of the Mineral Resource/Reserve involved and the time, effort and expenditure expected to be involved in bringing the project to fruition. Some eighteen recent and relevant transactions were analysed, allowing the following general conclusions to be reached: ? a Yardstick with which to value undeveloped PGE mineral resources is likely to range between 0.5% and 2.5% of the in-ground contained metal value ? the expected method of mining (especially with regard to mining costs) and the grade of the mineralization both have a strong influence on the Yardstick ? the status (classification) of the Mineral Resource has some influence on the Yardstick and ? the ruling price of platinum and the regional location of the deposit appear to have insignificant influences on the Yardstick.

Jan 1, 2006

By M. R. Yenchek

The U.S. Bureau of Mines designed and constructed sensitive and coordination-free ground-fault relays (GFR's) for use on mine power systems. First, a list of GFR attributes for mine ac utilization applications was compiled. These practical guidelines specified design, construction, transient immunity, reliability, and operating criteria. The time-current characteristics of the ac and dc units, subsequently fabricated, were designed to be below the human electrocution threshold. The significant and highly variable capacitance of high-voltage distribution cables was found to preclude the sensing of ground currents in the milliampere range. However, the coordination-free system developed for high-voltage distribution should enhance safety by significantly decreasing response time to ground faults. Implementation of the sensitive GFR technology in the mining industry has the potential to eliminate the majority of injuries and nearly all the deaths resulting from contact with energized components.

Jan 1, 1990

By José Arango

La Planta Hidrometalúrgica de Cerro Verde tiene como objetivo alcanzar la máxima calidad en cada uno de sus procesos operativos. Para ello, desarrolla un diseño que permita la transformación del control remoto a una operación automática, generando decisiones lógicas. En ese sentido, el presente texto señala la importancia de los Sistemas de información de operaciones en el sistema de automatización de Cerro Verde - en tanto es soporte de la implementación de un completo sistema de instrumentación y de la instalación de una red de PLC’s que colectan la información y en base a esta, desarrollan una lógica de operación manteniendo interconectados todos los circuitos operativos. Posteriormente, con el uso de software se crea una interfase de conexión entre la red industrial y la red Administrativa, permitiendo adjuntar la información en una base de datos que junto a la otra base administrativa, constituyen un ERP que da vitalidad a nuestra operación. De forma que los sistemas de informacion instalados en Cerro Verde consideran a los sistemas de instrumentación como los ojos del operador de planta.

Jul 17, 2000

The variation of carbon monoxide and hydrogen utilization with the amount of the reductant in the blast furnace bosh gas was investigated for the No. 4 blast furnace at The Broken Hill Proprietary Co. Ltd.iron and steel works. Newcastle. The degree of CO utilization decreased with increasing CO in the bosh gas; the H., utilization increased with the H., content of the gas. Empirical relationships for CO and H., utilization are proposed.H2, is 3-6 times as effective a reductant as CO at present levels of CO (34-39 per cent) and H2 (6-10 per cent) in blast furnace bosh gas. H2, gas injection into the blast furnace is proposed as a means of lowering the coke consumption, and the economics of H2 injection are evaluated.

Jan 1, 1975

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By J. L. Henry

The development and status of technology for producing titanium from U.S. resource materials are summarized in this Bureau of Mines report. Commercially feasible processes and investigations of alternative procedures are reviewed in order to identify techniques that could make existing operations more effective or areas in which future research may lead to the development of new production methods. Procedures are described for producing concentrated titanium dioxide from starting materials such as sands, massive deposits, and mineral processing residues containing rutile, ilmenite, and perovskite; producing and purifying titanium tetrachloride from concentrated rutile, ilmenite, and titaniferous slags; reduction of titanium tetrachloride to titanium sponge metal using metallic magnesium or sodium; purifying and consolidating titanium sponge and scrap by arc melting or induction melting techniques; purifying sponge, scrap, and alloys by molten salt electrorefining; and electrowinning titanium from chloride salts.

Jan 1, 1987

By Richard P. Stahura

During the next five years, there will be a trend toward performing belt cleaner maintenance while the conveyor is in operation. Most mines and industrial sites that use belt conveyors have an in-house safety rule that the belt must be stopped before maintenance work can be performed on any belt-cleaning device. This is a good rule. Most cleaning devices are positioned against the belt with hardware that requires the service technician to reach or climb into the chute to change the cleaning blades. But this simple rule becomes more complicated as production demands require higher conveyor availability and provide fewer conveyor outages. In many cases, today’s conveyors are expected to be available 98% to100% of the time.

Jan 1, 1996

By Douglas C. Brunot

Mabey Inc. is providing for the shoring design for the Naples bay Center project, located in Naples, FL. The excavation is approximately 374' long by 164' wide and is 27'-8" deep at the shoring line with a groundwater level six feet below present grade. The project Excavation is for a multi-use facility for residential and retail with underground parking. The shoring design will be incorporated into the foundation walls for the building. Mabey is using its pre-engineered Super Powerbrace Plus (SPP) wales and Mega Struts to support the excavation in two phases. The system design and the design of all the pre-engineered components are by Mabey. The foundation is supported on drilled shafts arranged with the building column grid. The excavation will be completed in two phases to allow for equipment mobilization and operation on a site with limited access. The construction sequence will begin with placement of the drilled shafts. The drilled shafts will also serve as the building columns. After the drilled shafts have cured, 630 AZ24-700 x 45 ft. long sheet piles will be installed. The sheets will be arranged in two phases, divided by a center row of piles. Since de-watering in south Florida is very expensive and often downright impossible prior to placing the seal slab, all the initial foundation and excavation bracing work will be completed with groundwater in situ. The entire excavation will be excavated to 5 ft. below ground surface to allow for the installation of the wale support brackets at 12 ft. on center, welded to the sheet piles. After the support brackets are installed, the SPP hydraulic wales and the Mega Strut hydraulic braces may be installed for both phases. Once the frames and struts are in place, Phase 1 excavation is completed, followed by Phase 2 excavation. The 4-ft. thick seal slab is then placed and cured in the wet. De-watering is now possible with the seal slab in place. Once the excavation is de-watered the leveling slab is placed and cured. The center row of sheet piles is then cut off at the top of leveling slab. With the leveling slab cured, the sheet piles have enough strength to support the excavation without the frames and struts near the ground surface. The permanent sheet piles are then seal welded for water proofing and the foundation walls are cast with the sheet piles. The design is modelled in 3D using REVIT to ensure accuracy of the design. The earth pressures are developed using Coulomb theory as there is a top frame and the frame and sheet pile are flexible and move to develop an active pressure wedge. Earth pressure uniform loads and loads from predicted surcharge are modeled in STAAD to determine load effects on the SPP frames and Mega Struts. Coulomb theory and Mabey’s structural model will be tested through monitoring with Mabey’s LIVEPin system. LIVEPin will be placed in struts for each phase of construction. The LIVEPin results will be calibrated with the structural model to determine actual frames forces and will also determine the actual earth pressures applied to the system from surrounding soil. Mabey has used the LIVEPin system in similar applications and this has helped us determine modelling accuracy.

Jan 1, 2018

By G. X. Zeng

A calculation programme of finite element method has been developed in order to study the behavior of excavation with sheet piling in soft clay. Based on a series of isotropically consolidated-undrained tests (CIU) on Hangzhou clay a linear relationship between the normalized initial tangent modulus number, E1, and stress-path parameter, a, is found for four different stress paths, and stress-path dependent modulus equations derived. Meanwhile, several influence factors, such as embedment depth and stiffness of the wall and soil conditions, were taken into consideration in the programme. Some valuable conclusions were obtained. Finally, a case history was studied by the proposed method of calculation. The result of calculation and the field observation are in good agreement.

Jan 1, 2010

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981