Search Documents

By K. Y. Lee, J. M. Park, C. W. Park

Laboratory-scale experiments were carried out to investigate the effect of ladle slag composition on the decreasing behaviour of aluminum content in steel, i.e., reoxidation of molten steel in contact with slag, using a vertical tube furnace. The steel composition and the slag system chosen were for ultra low carbon and CaO-Al2O3-FeO-MnO-MgO based to simulate ULC steel grades. It has been observed that the reoxidation rate shows a good relationship with (T. Fe) content in slag. In case of (T. Fe) content higher than 1.5 weight per cent, the reoxidation rate increases linearly with increasing (T. Fe) content. For a given (T. Fe) content, it decreases with the increasing (CaO)/(Al2O3) ratio of the slag. However, in the case of (T. Fe) content lower than 1.5 weight percent, no particular relationships are observed between the reoxidation rate and (T. Fe) content or the (CaO)/(Al2O3) ratio of the slag. These results were used to propose for an aim a slag composition for the ULC steel grades in a steelmaking plant. Keywords: slag deoxidation, slag killing, slag composition control, IF steel, ULC steel grade

Jan 1, 2004

By D A-F Batchelor

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.South-East Asia represents the world’s most productive tin province, mainly from placers. Kalimantan has been a major diamond producer, while in the 1980s a placer gold rush occurred in Indonesia and Malaysia. Reviewing extensive geological and mining data highlights phenomenal palaeo-environmental changes in the Sundaland region, interpreted to be responsible for generating ‘giant’ placers. Correlation of the Late Cainozoic stratigraphy has been facilitated from mine exposures and drill holes distributed throughout Peninsular Malaysia, the Indonesian Tin islands and Kalimantan, including contiguous marine areas with extensive shallow seismic profiling data. Knowing the association of rich placers with palaeo-environmental episodes and stratigraphical units has been helpful to facilitate their discovery. All three placer commodities responded similarly to region-wide landscape evolution following Mio-Pliocene high sea levels. Commencing with major regression, important stages comprised: a long period of landscape stability with deep weathering during the maximum Sundaland extent gradually rising sea levels/precipitation initiated slumping of mineralised regolith to form fans, later reworked by braided streams with aggradation (Old Alluvium); during episodic pluvial periods downcutting upgraded placers significant change occurred around Middle Pleistocene time with peneplanation and pedogenesis from Late Pleistocene time ‘modern’ fluviatile deposition (Young Alluvium) filled incised V-shaped valleys.Placer seams show systematic variation in stratigraphic position, in particular cassiterite especially occurs in the Old Alluvium (equivalent Upper Dahor Formation in Kalimantan). Gold is commonly richer in gravelly younger deposits, partly because of secondary precipitation within permeable alluvium. Reworked diamonds are predominantly concentrated especially in younger fluviatile alluvium.CITATION:Batchelor, D A-F, 2015. Conceptual exploration for tin, gold and diamond placer deposits in ‘Sundaland’ (Indonesia and Malaysia) by understanding the late Cainozoic stratigraphic context, in Proceedings PACRIM 2015 Congress, pp 499–506 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Orlando Ramírez

El presente trabajo describe el sistema integrado de seguridad a través de la norma OSHAS 18001 - 1999 y calidad ISO 9001 – 200m, donde la aplicación de la integración controla las desviaciones de los procesos oportunamente. Es decir, que a través de la procalsedad se reúnen tres elementos: productividad, seguridad y calidad,logrando una ventaja competitiva en el mundo globalizado.

Sep 12, 2005

By Robert J. Maron, Mark Fernald, Alex Van der Spek, O’Keefe. Christian, Tim Bailey

"Sonar array-based non-invasive flow measurement technology is becoming an accepted and many times a preferred method of measuring challenging single and multi-phase flows in the mineral processing industry. This fundamental sensor and measurement technology has been extended to two developments that provide new measurement capabilities useful for monitoring and managing slurry flows and pipes.The first development is the non-invasive measurement of real-time velocity profile of slurry flow in horizontal pipes. Multiple non-invasive passive sensors measure localized velocities and are combined to provide a velocity profile measurement. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities and/or higher solids concentration while avoiding solids deposition or plugging and its associated operational costs.The second development is the non-invasive measurement of pipe wear on slurry lines. Presently, such measurements are made by hand-held portable ultrasonic thickness gages. The numerous shortfalls associated with the manual method are overcome with a set of permanently or semi-permanently installed transducers clamped onto the outside of the pipe. This ring of sensors contains a series of conformable ultrasonic transducers spaced around the circumference, which are used to measure the thickness of the pipe under their respective locations. Compared to manual methods, this system and approach results in better repeatability and accuracy. It also decreases inspection labor costs and pipe access requirements. The minimal accuracy variations in the presence of varying environmental temperatures will be shown. Trending of pipe wall thicknesses in high wear pipelines will be illustrated. The benefits of significantly improved pipe wear monitoring in hydrotransport lines with abrasive solids, and associated improvement in the ability to insure safe operation and avoidance of costly environmental damage due to leaks caused by pipe wear will be discussed."

Jan 1, 2009

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

High-pressure grinding rolls (HPGR) are an accepted, but continuously expanding, comminution technology. The copper industry has a growing need to process harder ores with progressively lower grades, more challenging metallurgy and increasing demand for efficient bacterial leaching applications. This has resulted in a major focus on HPGR use in a crushing circuit. If the industry is to increase leach extraction while lowering energy costs in high-throughput hydrometallurgical operations, HPGR will be of inherent significance. The following paper summarizes test work on copper leach ores utilizing the benefits of HPGR comminution, while increasing several critical metallurgical parameters. Based on the current work and previous investigations, it was found that HPGR comminution within a crushing circuit, in specific instances, can result in 2 - >10% increases in cop-per extraction. The tested variables are crush size, rock type and copper mineralogy dependence. Various other process parameters may also be optimized.

Jan 1, 2011

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues that may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Min¬ing Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff cooperation across the country. MEA has also commenced some international teaching initiatives that are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual univer¬sity programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 2, 2010

By C T. Portelli

Belt conveyor transfers are the most likely location for high wear rates and failures. Belt transfers are necessary to change the direction of conveyed material and will remain a part of belt conveyor systems into the future. Burden being accelerated due to fall and changes in direction from one system to the next, prevents steady state flow which introduces component fatigue. The conveyor belt is considered the greatest cost item over the life of a belt conveyor system and consumes considerable downtime to replace, therefore a financial incentive exists to preserve this high-cost item. Other issues created at the transfer include health risks of uncontained dust and product losses due to spillage. Additional consideration to support the belt is one way to improve the life of components and contain dust within the transfer chute. The humble impact cradle/bed has changed little over the years whilst conveyor systems have achieved ever greater flow rates. Further development of the impact cradle is an opportunity to reduce maintenance costs and increase uptime. The peak technology on the market for conventional impact belt support is the dynamic impact cradle, which ensures the belt support area under the chute allows for some dynamic travel, whilst also maintaining a consistent skirt board area. The impact energy at a transfer when installed with Kinder Australia’s dynamic impact belt support system was measured to further understand the forces involved and how they compare with static belt support systems. Adding further dynamic capacity to the load zone has been shown to increase belt life by at least 30 per cent. Other components also benefit from reducing impact energy in the transfer and the incorporation of polyurethane bushes at roller supports has been employed further increase roller and frame life. Kinder Australia has developed a unique and innovative range of belt support technologies that further promote dynamic travel whilst maintaining a consistent skirt board area without a significant increase in belt-friction tension. This technology combines slider rails with rollers that can absorb impact independently within the support system and/or utilising exotic slider materials to overcome high belt speeds and/or system capacities. Kinder Australia has a vast library of documented case studies and application data to ensure the future systems being offered will survive, provide better chute sealing and protect the conveyor belt.

Sep 18, 2023

By F. D. Wright, H. D. Fara

The solution to the plastic and elastic stresses around a circular shaft in a hydrostatic stress field that has appeared in two editions of a widely used book on rock mechanics1 is in error. Although this is a relatively minor matter, the correct solution was not found by a literature survey, so it appears worthwhile to present it. For a homogeneous, isotropic, rigid plastic-elastic body in plane strain which obeys Tresca's yield criterion the following equations must be satisfied:'," In the plastic zone,

Jan 1, 1963

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By William C. Miller

This report describes investigations by the Bureau of Mines designed to establish the noise level and spectrum of various types of pneumatic rock drills and to furnish information that would be useful in conducting sound measurements in mining environments and in reducing the noise generated in pneumatic drilling. These investigations show that (1) the noise generated by the drills in the frequencies below 100 cps is caused by the impact of the piston and drill steel, in the frequency range between 100 and 2,000 cps by the exhausting of air from the ports, and in the frequencies above 2,000 cps by the resonant frequencies of steel drill parts and of drill steel; (2) satisfactory instruments and instrumentation systems are available for field and laboratory measurements; (3) reliable sound measurements can be made in mining environments; and (4) devices can be developed that will abate the noise.

Jan 1, 1963

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

By James F. Davis, Matthew A. Conte, Robert F. Tonning

This is a paper demonstrating the steps taken to combine multiple types of piles for a single site to maximize the benefits and characteristics of each method. We intend to discuss the use of grouted displacement piles in lieu of traditional pile types that were specified on an individual project. We will show how implementing this alternate pile type can both supplement and replace the originally specified pile to increase efficiency and lower costs. We will demonstrate a reduction in spoils, vibration, crew hours, and equipment size while employing methods to overcome unforeseen ground conditions.

By Pieter de Waal

The use of valuable minerals is a necessity to maintain a modern society. Not only the iron, aluminium, coal and oil that are used in large quantities, but also the uranium, copper, vanadium, tungsten, antimony and many others play an essential role in the bigger picture of our modern civilisation. Minerals occur in a form and in places determined by a long history starting at the dawn of creation. Over billions of years the elements have combined in wondrous combinations and structures. They have been broken up by massive explosions, movements in the earth's crust and erosion by wind and water. They have been restructured and recreated in even more configurations by the application of heat and pressure, leached by and exposed to new chemical compounds. The result is that most valuable minerals are found in impure form and mixed up with other, less useful waste material. 2. Mineral Beneficiation The processes used for the purification and enhancement of an ore, to satisfy the needs of downstream applications, are collectively referred to as mineral beneficiation. Mineral Beneficiation starts in the mine where only that portion of the ore, that can be economically processed, is selectively extracted. It may also include ore blending, to ensure a more consistent feed to the following stage of valuable mineral recovery. The next stage in mineral beneficiation is the liberation of the valuable minerals from the gangue. This is achieved by blasting, crushing, milling and grinding down to an adequately fine grain size to facilitate good separation. Separation can be achieved by a variety of different techniques. ?Screening coarse from fine particles is an easy method if the valuable mineral is dominant in a certain screen fraction. ?Magnetic separators can differentiate minerals on the basis of their difference in magnetic susceptibility. ? Electrostatic separators differentiate on the basis of electrical conductivity. ? The differences in density are exploited in spirals and jigs. ? Particular surface properties provide a separation technique in flotation. ?The selective sorption properties of a collector medium are another option.

Jan 1, 2007

By L. F. Pease, J. H. Brophy

A phase diagram for the Ta-Zr system is presented. The system is of the minimum-melting point type with the 0-zirconium phase decomposing monotectoidally at 785°C and 95.5 at. pct Zr. The minimum solidus temperature is 1875°C and the temperature of the top of the monotectoid loop is 1775°C. Techniques employed included X-ray diffraction and fluorescmce, electron microprobe analyses, diffusion couples, metallography, and melting-point measurements. Errors due to interstitial solutes and in melting observations are particularly common in this system, and their occurrence is discussed. SEVERAL versions of the Ta-Zr phase diagram have been reported in the literature.lm7 Williams et al.' report a diagram of the minimum-melting point type with a monotectoid reaction at 800°C and 12 wt pct Ta. The minimum in the solidus occurs at 1820°C and 25 wt pct Ta, while the top of the monotectoid gap is located at 1780°C and 80 wt pct Ta. The experimental techniques employed were metallography, electrical resistance variation with temperature, dilatometry, X-ray diffraction, and direct observation of melting by the technique of Pirani and ~lterthum.' Experience in the Nb-Zr phase diagram has shown that small changes in the interstitial content can cause large shifts in the positions of the phase boundaries. Small amounts of inter -stitials can cause similar changes in the Ta-Zr system and may be responsible for the wide variations in the phase diagrams previously reported.'-' The authors15 have found that alloys containing 0.75 wt pct 0 and 1.0 wt pct Ni with tantalum contents from 19 to 85 at. pct often contain a lamellar or cellular precipitate after annealing above 1400°C. This precipitate is very similar to that reported by pollack,12 Ralls," and Donlevy17 for the Ni-Zr system. In the present investigation, a wider variety of experimental techniques and improved alloy purity were applied to the resolution of errors in diagrams for this system as they now appear in the literature. New results have been obtained in the areas of alloy homogeneity and purity. Errors in the common techniques of direct melting observation in binary alloys have been demonstrated. In the commercially important high-tantalum region, the more accurate metallographic method of solidus determination has been employed. EXPERIMENTAL PROCEDURE Nominal analyses of the materials employed are given in Table I. The zirconium was low hafnium reactor grade iodide crystal bar, and the tantalum was in the form of high-purity sheet. Powders were impossible to use because of gas content. Alloys were melted on a water-cooled copper hearth, with a thoriated tungsten-tipped nonconsumable electrode in 2/3 atm of Zr "gettered" argon. Alloys were

Jan 1, 1963

By C. Musingwini, M. Mohutsiwa

"SynopsisCapital cost estimates are important in decisions on whether a project will be approved, mothballed, or abandoned. In South Africa, junior coal miners do not have extensive databases of historical projects from which to estimate capital costs. The purpose of this paper is to establish formulae that can be used for estimating capital costs of developing coal mines in a coal-producing country, using South Africa as a case study. The costs are estimated to an error of magnitude level of -30% to +50%, which is suitable for a concept study level, using a parametric estimation technique. The study uses data from completed coal mining projects from selected coal-producing countries. Three formulae are developed and presented for estimating capital costs of underground bord and pillar, surface shovel and truck, and dragline operations.IntroductionCapital cost estimates play a critical role in deciding whether projects will proceed, be delayed, or abandoned. It is therefore important that capital cost estimates are carried out accurately as determined by the estimation guidelines based on the level of estimation conducted (Shafiee and Topal, 2012). The lack of literature on estimation of capital costs in many coal mining countries is adversely affecting junior coal miners, since they do not have an extensive database of historical projects on which to base estimations. In South Africa, the difficulty in estimating capital costs is attributable to lack of publicly available data on completed South African mining projects (Hall, 2013)."

Jan 1, 2015

By P. A. Dimas

A new family of sulfide flotation collectors has been developed in our laboratory. These formulations are comprised of novel renewable materials combined with conventional reagents. The resulting diversity permits tunability of collector chemistry to meet a range of flotation problems. Several attributes of the new collectors are presented.

Jan 1, 2012

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.