Search Documents

By H. P. Greenwald

[In many coal-mining countries, during he pest decade, there have seen made extended studies and accurate measurement of movement of roof strata, tests of the physical properties of specimens cut therefrom, and tests of the strength of end load on artificial supports. Naturally, such studies have been more extensive in European countries, where mining conditions are less favorable than in the United States. As a part of its work in the conservation of coal resource and prevention of accidants in mines, the Bureau of brines began systematic measurements of the movement of roof strata to in coal mines in the fall of 1935. It was decided- that, in the beginning, work on a rapidly retreating rib line in a mechanized mine would give the greatest amount of information in a reasonable time. To this end w cooperative tine agreement was made with the Pittsburgh Coal Co., through Dr. L. E. Young, vice: president in charge of operations, for conduct of work in that company's Montour 10 mine operating in the Pittsburgh coal bed. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as appear to be justified.]

Jan 1, 1937

By H. P. Greenwald

[In many coal-mining countries, during he pest decade, there have been made extended studies and accurate measurement of movement of roof strata, tests of the physical properties of specimens cut therefrom, and tests of the strength of end load on artificial supports. Naturally, such studies have been more extensive in European countries, where mining conditions are less favorable than in the United States. As a part of its work in the conservation of coal resource and prevention of accidents in mints, the Bureau of Mines began systematic measurement of the movement of roof strata to in coal mines in the fall of 1935. It was decided that, in the beginning, work on a rapidly retreating rib line in a mechanized mine would give the greatest amount of information in a reasonable time. To this end a cooperative agreement was made with the Pittsburgh Coal Co., Dr. L. E. Young, vice president in charge of operations, for conduct of work in that company's Montour 10 mine operating in the Pittsburgh coal bed, This paper gives an account of the methods used in the investigation, excerpts from the date obtained, and such generalizations as appear to be justified.]

Jan 1, 1937

By John P. Shubilla1, Nicholas Kyriazi

A joint effort by the Pittsburgh Research Center (PRC) and the Mine Safety and Health Administration (MSHA)3was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fifth phase of testing from mid-1993to early 1996. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS) at PRC. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily.

Jan 4, 1996

By I. R. Hanby

A simple solution to the problem of whether to round the calculated number of trucks up or down to the nearest whole number is to adopt as criterion the minimum cost per unit volume/mass moved, assuming all trucks in the fleet are of the same type. When the effects on journey time of varying haul-road slope are calculated for several rolling resistances, it is shown that the optimum angle of 7.5 degrees is moderately independent of both rolling resistance and height climbed; the lower the resistance, the lower the sensitivity to ramp angle, but if haul-road gradients do not exceed 1 in 10 (5.7 degrees) for safety reasons then travelling time will never be more than 7% greater than its theoretical minimum. Further calculations result in a graph of the maximum payload values to incur the minimum cost, for different values of total effective resistance

Jan 1, 1991

By John D. Campbell

"IS YOUR MANAGEMENT CONTROLLOOP FUNCTIONINGMineral processors make use of hundreds of control circuits in their mills, process plants, smelters and refineries, to optimize throughput and recovery and minimize cost. This afternoon, I would like to discuss what is probably the weakest circuit in any mineral processing operation - the management control loop.In their recent book ""The Winning Streak"", Goldsmith and Clutter describe extensive research on unsuccessful companies. They conclude that ineffective control, which does not immediately identify the problems, is one of the main failings of unsuccessful companies.We will look at the three key components of control which, from the manager's point of view, ensure that the loop is complete. These three are:• measuring what's happening,• assessing its significance, Rnd• altering performance.If we compare management control to process control as shown in this first figure, ""We see that parameter sensing by the analyzer in a process circuit is analogous to performance monitoring by management in a responsibility centre. The analyzer senses temperature, pressure, flow, weight or some surrogate indicator such as colour to indicate ion concentration. For manage1nent, the performance to rnonitor is dependent upon the objectives of the responsibility centre, and the key factors which affect these objectives."

Jan 1, 1985

By M. R. Campbell

"IntroductionON THE LAST DAY of December, 1951, a half-century of steel production was completed in the open hearth department of Dominion Iron & Steel, Limited, in Sydney, Nova Scotia.During that period, almost every known variation of basic steel making practice was used in working out a steel making process which would overcome the difficult metallurgical problems imposed by the use of Cape Breton coal and Wabana ore.This paper is presented as a brief review of these steel making practices, setting forth the fundamental metallurgical factors involved in their success or failure.Establishing the IndustryThe story of steel production at Sydney is closely interwoven with that of coal. The steel industry owes its inception to a desire on the part of the Dominion Coal Company, which was incorporated in 1893, to improve its marketing position by increasing sales of slack coal and providing a year-round demand for its product. Accordingly, the Dominion Iron and Steel Company, Limited, was incorporated on March 30th, 1899, with Mr. H. M. Whitney -who was President of the Dominion Coal Company -as its first President. The new Company was given powers to manufacture and process iron and steel, and to mine all minerals, including coal.A strong inducement to the industry was the bounty offered by the Dominion Government for the production of both iron and steel."

Jan 1, 1952

By G. Bulut

The recovery of copper and cobalt from ancient copper slags from the Küre region of Turkey was investigated. A fayalitic-type of ancient copper slag containing 1.24% Cu, 0.53% Co and 53.16% Fe were subjected to an experimental study. Two different routes were followed to recover the metal values. The first route was roasting the slag with pyrite followed by leaching. The second route was flotation of the slags, roasting of the flotation tailings with pyrite and leaching. The second route was found to be suitable for the treatment of the copper slag studied. In the flotation step, a copper concentrate containing approximately 11% Cu was produced with a 77% recovery while 93% of the cobalt stayed in the tailings. In the roasting experiments, the effects of roasting time, pyrite: slag ratio and roasting temperature on the dissolution efficiencies of Cu and Co were investigated, and the optimum conditions were determined. In the tests, 87% of the cobalt dissolution was observed after one hour of roasting at 500°C with a pyrite: slag ratio of 3:1. The copper dissolution in the tests was 31%. Based on the results of this study, a process flowsheet is proposed for the evaluation of these slags.

Jan 1, 2007

By A. H. Marquis

Since the start-up of its first Direct Reduction Module in April 1973, S1DBEC has produced over 2 million tons of prereduced iron. During this period, SIDBEC has acquired comprehensive experience in the operation of the direct reduction process and at the same time has learned to recognize the characteristics that the oxide should have to constitute an adequate feed for the process. A comparison is made as to the design and operation of the two direct reduction units now operating at Contrecoeur, Que. A description is given of a method of evaluation of a direct reduction unit, which takes into account the main process variable sand which permits comparison ofthe results on a daily basis. The paper defines the characteristics that the iron oxide and the prereduced iron pellets must have to meet the specific requirements of the direct reduction and the electric arc furnace processes. A simple model makes possible a rapid evaluation of the technical and economic effect related to the use of a given raw material. Finally, the paper outlines the advantages of prereduced iron in the steelmaking process and on the quality of the steel products.

Jan 1, 1979

Valuable Components Recovery from Lead-Zinc Metallurgical Slag

Sep 13, 2010

By Francis X. Cannaday

Equipment and techniques were developed with Bureau of Mines facilities for measurement in the laboratory of sonic shear wave velocity in variously shaped rock specimens in a wide range of sizes. A variety of rock types was tested. The shear wave front is produced by electronically excited, piezo-electric ceramic) disk-shaped transducers. Transmitter and receiver are interchangeable. Special equipment components were Bureau produced; other components were commercially available. The equipment permits quick measurement of shear wave velocity on variously shaped specimens with a minimum of specimen preparation. The technique, under favorable conditions, allows for determination of the moment of arrival of the shear wave when it is superimposed on a weak longitudinal wave.

Jan 1, 1968

It is predicted that vast volumes of affected mine water will be produced by mining activities in the Mpumalanga coalfields of South Africa. The potential environmental impact of this excess water is of great concern in a water-scarce country like South Africa. Research over a period of more than 10 years has shown that this water can be used successfully for the irrigation of a range of crops (Annandale et al., 2002)1. There is, however, continuing concern from the local regulators regarding the long-term impact that large-scale mine water irrigation may have on groundwater quality and quantity. Detailed research has been undertaken over the last three years to supplement the groundwater monitoring programme at five different pilot sites, on both virgin soils (greenfields) and in coalmining spoils. These sites range from sandy soils to very clayey soils. The research has included soil moisture measurements, collection of in situ soil moisture over time, long-term laboratory studies of the leaching and attenuation properties of different soils and the impact of irrigation on acid rock drainage processes, and in depth determination of the hydraulic properties of the subsurface at each of these sites, including falling head tests, pumping tests and point dilution tests. This has been supported by geochemical modelling of these processes to quantify the impacts. The results indicate that many of the soils have considerable attenuation capacities and that in the period of irrigation, a large proportion of the salts have been contained in the upper portions of the unsaturated zones below each irrigation pivot. The volumes and quality of water leaching through to the aquifers have been quantified at each site. From this mixing ratios have been calculated in order to determine the effect of the irrigation water on the underlying aquifers. Keywords: coalmines, irrigation, gypsiferous mine water.

Jan 1, 2009

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

By Sidney Katell

This cost bibliography, covering the period from January through December 1960, is a continuation of the series which began with the publication of Information Circular 7516 in October 1949. It is also the second report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, came from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal. Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil.

Jan 1, 1961

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004

By R. Webber, D. Averill, L. Whittle, D. Moffeti, G. Kassakhian

"This paper describes the recent pilot-plant work carried out on two alternative processes capable of producing an effluent containing less than 10 pCi/L total radium-226 activity and very close to 3 pCi/L dissolved radium-226. The processes incorporate coprecipitation of radium with barium sulphate by the addition of barium chloride in continuously stirred tank reactors followed by either chemical coagulation with ferric chloride, flocculation and clarification, or polymer-aided dual-media filtration. IntroductionUranium mines in Canada have practiced radium removal from tailings basin effluents since 1965. Treatment consists of addition of barium chloride to precipitate radium as barium- radium sulphate and provision of natural or constructed settling ponds for sedimentation. This process, however, has been identified as being deficient in that it allows particulate or suspended radium-226 releases which are higher than the regulated dissolved values». Also, the large size of some of the settling ponds is believed to represent a real limitation of the present technology because of inferred difficulty in recovery of barium-radium sulphate precipitates.The Federal Government Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical/chemical treatment systems as an alternative to settling ponds. In response to the SubGroup recommendations, a bench-scale study began in March 1976at the Wastewater Technology Centre (WTC) of Environment Canada . The results of this study indicated that coagulation and flocculation of the precipitate from barium chloride addition is a viable alternative to sedimentation in settling ponds(3). The bench work was expanded and accelerated in 1977, with financial assistance provided by the Atomic Energy Control Board. Subsequently, a research program with a larger scope was developed; this program is jointly managed and funded by government and industry, as shown in Table I.One of the goals of the joint program is to develop, at pilot scale, a physicalI chemical process to reduce the radium-226 content of uranium mining and milling effluents. Target radium-226 activities for treated tailings basin effluents were set: namely, 10 pCil L total and 3 pCil L dissolved radium 226. Extensive bench-scale and pilot-scale work was conducted through 1978 and 1979 and has culminated in the development of two physical/chemical processes. This paper describes work carried out at a pilot plant which led to the selection of the two physical I chemical processes for demonstration. In short-term tests, the processes produced effluents meeting the radium-226 target activities."

Jan 1, 1980

By Antonio De Biase

In October 2006, a 7m Double Shield TBM, boring through very poor volcanic formations, was pushed back by fluid mud, which presence had not been detected during previous field investigations, due to the high covers characterizing the majority of the tunnel axis. The present work describes the investigations made to gain better knowledge of the conditions in front and all around the TBM, the special measures implemented, the exploratory and bypass tunnels excavated, the extraordinary occurrences came true during the execution of these tunnels, the drainage campaigns, the design of the chamber excavated to free the TBM, the dismounting and restarting of the TBM.

By Benedicto Hadad Cintra

In an inflationary environment the need for reduced cost is a daily concern of all industries. The Du Pont do Brasil "Expanded Pattern" method has proven to be an extremely effective means of reducing costs in mining, quarrying and construction operations. Over the past years much emphasis was placed on rectangular drilling patterns where the burdens are less than the spacing. The Expanded Pattern method combining rectangular and staggered patterns, was implemented in 1971 in Brazil after extensive trials in close collaboration with numerous explosives users and Du Pont do Brasil Technical Services Engineers. The best multiple row spacing-to-burden ratio (S/B) was demonstrated to be in the 2 to 5 range and the effective spacing to burden ratio (Se/Be) was found to vary from 5 to 11. These ratios are for the interior of the blast pattern and do not hold true along the front row of holes. Geological rock properties, hole diameter and inclination, explosives energy and loading density, explosives characteristics, blast pattern geometry, bench height and delay patterns along with type and size of digging, hauling and crushing equipment must all be evaluated for each and every operation. The integration of these interrelated parameters, together with sound blasting practices are the basis for the Expanded Pattern method. Color slides and documented case histories will be presented.

Jan 1, 1985

By F. Stober, D. Wanblad, J. Ndlovu, L. R. Nelson, L. P. S. de Villiers

The single six-in-line furnace of the Polokwane Smelter is the largest installed high-intensity furnace for platinum group metals (PGM) base metals sulphide smelting in the world. The furnace employs state-of-the art technology to deliver a planned throughput of 650 000 t/a dry concentrate at a design 68 MW power input. This furnace, at double the capacity of previously existing PGM furnaces, offers low unit operating and capital cost through the resulting economies of scale. Key features of the design include:

Jan 1, 2005

By M. Neven, R. A. Steane, E. Lam

"The Key Lake uranium mill is located in Northern Saskatchewan. It treats a high grade, complex uranium and metal sulphide ore. The plant and process are in many respects unique, because commercial treatment of this type of uranium ore had never been done before. The process and engineering design was based on extensive laboratory test results. A pilot plant testing stage was omitted because of confidence in the test results and time constraints to bring the plant into production.The bench scale testwork on exploration drill core samples along with preparation of the feasibility study and environmental impact statement were carried out between 1976 and 1979. The contract for detailed engineering was awarded to Wright Engineers of Vancouver in late 1980 and in August of 1981 following a public inquiry, approval to proceed with construction was granted.Construction began immediately, and during the winter the foundations for many of the plant buildings were poured and by the beginning of the following winter the buildings had been erected and installation of equipment began. Despite a six month construction worker strike in 1982, the crushing plant started up in June of 1983 and ore processing commenced in October of that year, approximately 3 months behind the original schedule.This paper describes the mill design and compares the expected performance, with the operating experience. Emphasis is directed towards flowsheet and equipment changes made since start-up, operational difficulties encountered and further improvements envisaged. Auxiliary systems are only discussed where they directly affect mill operation."

Jan 1, 1986

By Charles D. Wood

"Selected Topics,? in reviewing the control of emissions from diesel engine powered equipment used in underground mining, explores these fields of interest: hydrogen as fuel; lubricating oil as a source of particulates; applicability of stationary source scrubbers; worldwide diesel exhaust scrubbers; instrumentation technology for measurement of N02; control of emissions through application of sensors and microprocessors; use of fuel additives; technology transfer of marine diesel practice; technology required to use 4-stroke, aftercooled, turbocharged, direct injection engines; oxidation and reduction catalysts for diesel engine exhausts. "Selected Topics? makes recommendations for research and provides a bibliography and lists of references.

Jan 1, 1979