Search Documents

By J. S. Miller

The Bureau of Mines conducted surface tests to determine the feasibility of using liquid explosives for underground rock fracturing. The effects of configuration, confinement, length, critical layer thickness, and fracture-propping sand on detonation and explosive propagation velocity of desensitized nitroglycerin were studied, using polymethyl methacrylate and glass-plate reservoirs through lengths from 3 to 12 ft, with explosive-layer thicknesses from 0.1875 to 0.0312 in and in aluminum tubes 8 ft long with diameters from 2.000 to 0.125 in. Interval and continuous detonation velocity data were obtained. Under the test conditions detonation velocity was dependent upon explosive confinement and fracture-propping sand. The detonation velocity of a confined nitroglycerin explosion in aluminum tubes can be reduced by as much as 85 percent, when the tube contains fracture-propping sand. The shape of the reservoir, whether triangular or rectangular, has little effect on the detonation velocity or explosive propagation. The critical or minimum explosive-layer thickness between glass plates, capable of supporting propagation, was 0.0312 in. The presence of a fracture-propping sand in the sheetlike layers increased the critical explosive layer thickness to 0.0625 in. In nitroglycerin-filled and nitroglycerin-sand filled tubes, the minimum tube diameters successfully tested were 0.125 in and 0.375 in, respectively.

Jan 1, 1969

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

By Bernard Hertlein

¦ Drilled shafts resist scour seismic loads better than groups of driven piles ¦ Drilled shaft construction creates less noise and vibration than driving piles ¦ Drilled shafts permit direct observation of bearing stratum, and confirmation of location ¦ Drilled shafts are cost effective

Jan 1, 2001

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By Charles W. Axten

Since the mid-1970s, samples of airborne and waterborne fibrous particulates have been collected in the area of the Northshore Taconite Ore Processing Facility by the Minnesota Department of Health (MDH), the Minnesota Pollution Control Agency (PCA), and the University of Minnesota. Indirect sample preparation has consistently been used although other aspects of the sampling methods and sites have varied and analytical procedures were altered over time as more accurate and precise microscopy methods were developed (i.e., phase contrast optical microscopy, transmission electron microscopy, transmission electron microscopy with energy dispersive spectroscopy). In the mid-1970s, levels of airborne fibrous particulate in the Silver Bay area averaged from 0.00030 to 0.03 f/ml. This level was significantly greater than levels of similar particulates in the St. Paul, MN area, although two of the Silver Bay sampling sites, considered individually, did not indicate levels of fibrous particulate markedly different than that seen in St. Paul. More recent sampling data (i.e., 1990?2001) indicate mean concentration of airborne fibrous particulates (amphibole-like fibrous particulates) of 0.0020 f/ml with a range of values from 0.0001 to 0.0140 f/ml. Such levels are not significantly different from those seen in other non-urban environments in the US and Europe. Concentrations of fibrous particulates in water samples were higher in the mid-1970 when iron ore tailings were being deposited in Lake Superior, but since the tailings have been deposited on land waterborne levels of fibrous particulate in the Beaver River have remained relatively constant averaging in the range of 7.5 MFL. This level is only slightly in excess of the current EPA drinking water standard for fibrous particulates. Review and consideration of this data is important in determining the potential health risks associated with airborne and waterborne fibrous particulates in the areas of the Northshore Taconite Ore Processing Facility. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Asbestiform fibers; Fibrous particulates; Cleavage fragments; Phase contrast optical microscopy; Transmission electron microscopy

Jan 1, 2007

By F. G. Heivilin

We are no longer short of viable Rare Earth deposits. As little as 2 years ago China mined and produced 97% ofthe world?s rare earths. Only a few deposits were in an advanced stage of exploration and development. Now Technical Metals Research (TMR) Gareth Hatch *5 reports that 347 deposits are being developed by 265 companies down from 440 on July 6th. Their Index of Advanced projects lists 45 projects in 14 countries. They will sustain the world for centuries to come and many good deposits are yet to be found. The problem is mining 14 elements in balance. Each of the deposits listing production in the chart has a unique set of minerals which they think will give them a cost advantage. Which of these will make it to production is a question. Most of the Advanced won?t be mined soon, but which ones? China is still in the driver?s seat in Light Rare Earth production (LREO) with one deposit with 35 million ton Baiyunebo deposit in Inner Mongolia which is part of a working iron ore deposit. The number of HREE deposits have been reduced and they attempting to eliminate unpermitted mines. This report will tell you what a Rare Earth is, how rare they are, why they are important, and where they are being developed which includes Australia, the United States, Africa, Greenland, Brazil and Canada.

Feb 27, 2013

By Rainer Kahrger

During the last decade, advances were made in solvent extraction/electrowinning (SX/EW) technologies. Combined with heap leaching, these technologies made it viable to exploit large, low-grade oxide copper deposits. The El Abra Mine is a good example for such a deposit. The deposit is situated in northern Chile at an elevation of about 4,000 m (14,000ft), 70 km (45 miles) north of Calama. Codelco sold 51% of the El Abra to Cyprus Minerals in June 1994, with Codelco retaining the balance. In 1993, Cyprus and the engineer on the project began discussions withinternational companies regarding the materials-handling system requiredfor the project. These early discussions were considered critical for this fast-track project.

Jan 1, 1996

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By K. Hopperstead

Ventilation planning in trackless metal mining is often taken for granted. This paper highlights the trials of planning and executing the ventilation design for Bog Zone at the Lisheen Mine. Ventilation planning for Bog Zone started at the feasibility study stage in 2003; subsequent design changes continued until 2006. In August 2006, the development of the Bog Zone ore body was accelerated through the use of contractors; in addition, the Lisheen equipment fleet was revised based on a larger load and haul fleet. As a result, the circuit was reviewed in terms of changes in design conditions and best practices. This review resulted in a 40% increase of total airflow required to mine Bog Zone. Resources utilized to design the circuit include: external review, computer modeling, and in-house Lisheen planning and operational staff review. The final ventilation design configuration was adopted in 2007, after modeling and evaluating 30 different scenarios, resulting in a better distribution of airflow, optimized secondary escape way, reduced contaminants, and a total power reduction. The value of investment in computer modeling of primary ventilation circuit and planning for staged implementation should never be underestimated.

Jan 1, 2009

By R L. Brathwaite

As part of an investigation of the deep structure of the Waihi Basin, an extensive set of resistivity measurements was recently collected by DSIR Geology & Geophysics. The objective of this work is to map deep resistivity changes throughout the Waihi area in order to contribute to a better understanding of the regional geophysical structure. This research is also aimed at improving techniques for locating 'deposits of epithermal mineral resources, and helping to establish their origin and genetic relationship to fossil geothermal systems.   The results indicate that the basin south of Waihi is underlain by an extensive layer of low resistivity, modelled as a 5ohm-m layer several hundred metres thick. Lake sediments (mudstones), as exposed in the south western part of the basin, near Waitawheta, are the most likely source of this low resistivity layer, although hydrothermally altered clays and/or elevated temperatures are other possible causes. Strong northeast trending anisotropy is also observed, implying structural links from Waitawheta through to Golden Valley. The observed resistivity pattern is consistent with a æburied calderaÆ or æfaulted depressionÆ structural model for the basin, as inferred from gravity and magnetic data.

Jan 1, 1991

Mineral formations, accumulated during technogenic activities greatly influence an economic and ecological situation in the Kola North. On the one hand, the dumps from extraction of mineral resources, tailing ponds of beneficating plants, ash dumps, wastes of metallurgical and mechanical engineering productions destroy the regionÆs environment and require taking certain measures and costs to bury or protect from weathering, oxidation, etc. On the other hand, technogenic mineral formations contain a lot of valuable scarce components. The amount of solid wastes increases annually, causing damage to ecology and economy. Researches conducted in recent years showed a possibility and economic expediency of comprehensive processing of wastes from different enterprises in Murmansk region and their use for production of new competitive commodity output, possessing high consumer properties. Thus, involving mineral wastes from Khibiny apatite deposits into hydrometallurgical industrial processing provides the basis for setting up a large beneficating-metallurgical complex. In this case ores and wastes from other deposits on the Kola Peninsula, containing titanium, rare, rare-earth and other valuable elements, may be involved into processing. Establishing such a complex will allow to organise a deep processing of natural resources, utilise some production wastes, improve ecological security and supply production with competitive output. Expanding the complex implies not only involving new mineral raw material into processing, but mainly deepening raw material processing, maximum utilisation of local natural resources and obtaining a wider variety of prime products.

Jan 1, 2002

By Emmanuel Henry

Few industries are more challenged by technical, political and market uncertainty than the mineral industry. Technical uncertainty in mining projects concerns the volume and quality of the resource, the processing and metallurgical parameters, the production efficiency, etc. Political uncertainty can take diverse forms and includes possibilities of change in the taxation system, risk of expropriation and risk of social instability or war. Market uncertainty depends on the market structure of the commodity; price and demand volatilities are the most common sources of market uncertainty. Intensive feasibility studies including these uncertainties and risks are required before investing up to billions of dollars in the development of a new mine. Current feasibility studies are often based on a single (or very few) mean geological scenario and simplified price profiles along the life of the project. Yet, strategic decisions, for example, the level of investment in exploration and metallurgical studies, adoption of a flexible, but more costly, mine design and risk-sharing strategies are made at an early stage. Over the last twenty years, Real Option theory has emerged as a unifying framework enabling strategic planning under uncertainty (technical, political and market). Geological and market variances (second order statistics) are pivotal for proper uncertainty quantification. The present study explores the possible benefits of combining modern geostatistical tools and financial techniques for project management. More precisely, the following questions are examined: Is geological uncertainty really an issue? Can we combine geological and price uncertainties in a unifying Real Option framework? A simple example aimed at illustrating the concepts involved is presented.

May 1, 2003

In September 2003, a test was conducted to see if a115-mm- (4.5-in.-) diam Mocap Vari-Stem blasthole plug could improve the pattern of explosives using different top stemming material. The test took place at the J.S. Faulkroad and Sonsstone quarry in McCalisterville, PA. The test consisted of a production stone blast. Half of the holes were stemmed with standard crushed stone. Two-thirds of the remaining half were stemmed with Vari-Stem plugs and crushed stone. And the remaining one-third of the second 50 percent was stemmed with Vari-Stem plugs and only drill cuttings.

Jan 1, 2004

By V. Rajagopal

Corrosion and abrasion properties of a series of chromium-containing cast iron balls with Cr contents ranging from 0 to 29% was evaluated and compared with austenitic stainless steel and mild steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite with either 5% pyrrhotite or 5% chalcopyrite under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynamic polarization curves under abrasion. An offset in their electrochemical activities was observed somewhere between 16 and 26% Cr. In fact, 26 and 29% Cr cast irons showed an excellent corrosion resistance approaching that of austenitic stainless steel. Flotation recoveries were estimated on a 95% quartzite + 5% pyrrhotite sample ground with various cast iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with corrosive wear obtained from marked ball wear test and with flotation results.

Jan 1, 1991

By C. F. Lucks, W. D. Wood, H. W. Deem

Electrical ad thermal-conductivity measurements have been made on titanium and 6 titanium alloys. The following expression was derived for calculating thermal conductivity from electrical conductivity: K = 0.626 s T x 10-8 + 0.00497 where K = thermal conductivity, cal sec-1 cm-2 cm0C-1 s = electrical conductivity, ohm-]cm-1 T = temperature, deg Kelvin This expression gives calculated thermal conductivities that are not in error by more than 10 pct from the experimental values for A-55 titanium and the 6 alloys measured; namely, A-110AT, C-110M, C-130AM, Ti-6A1-4V, Ti-140A, and Ti-155A, which are representative of the presently available commercial a and a-ß titanium alloys. THERMAL conduction in a gas, liquid, or amorphous solid is accomplished by energy diffusion from molecule to molecule, a relatively slow process. For this reason, such materials have a low thermal conductivity. When a material is crystalline, there is in addition a heat transfer by a vibratory motion of the crystal lattice. It is the contribution of this lattice conduction that makes a crystal a much better conductor than a gas, liquid, or amorphous solid. Lattice conduction, however, does not account for the relatively enormous thermal conductivity of a metal. This is explained by the freedom of movement of valence electrons. These valence electrons drift in a metal in a direction toward a drop in electrical potential and, to a lesser degree, in the direction of a temperature drop in the metal. Since both the electrical and thermal conductivities of a metal depend upon the presence of free electrons, there should be some relatively simple relation between the two. Wiedemann and Franz in 1653 first discovered an approximate empirical relation between the electrical and thermal conductivities of metals at the same temperature. This ratio varies appreciably with temperature, and Lorenz later showed that by adding a temperature factor to the Wiedemann-Franz ratio the value of K/(s T) is constant, where K is the thermal conductivity, a the electrical conductivity, and T the absolute temperature. This Lorenz constant shows a greater variation for alloys than it does for pure metals, the ratio increasing slightly as the proportion of alloying elements increases. It has been found that a closer correlation between electrical conductivity and thermal conductivity can be obtained by means of an equation of the form K - A s T + B [1] where A and B are constants. In this equation the term AsT is the contribution of electronic conduction and B is the contribution of lattice conduction to the total thermal conductivity. EXPERIMENTAL MEASUREMENTS Electrical-resistivity and thermal-conductivity measurements on titanium and 6 titanium alloys serve as the basis for determining an equation of the K = AsT + B type for titanium alloys. Specimens—Table I shows nominal compositions of the 7 metals on which electrical and thermal conductivities were measured. The electrical and thermal-conductivity specimens for each alloy were taken from stock of the same heat and usually from adjacent sections of the same bar. All of the metals measured were in a mill-annealed condition. Methods—Electrical-resistivity measurements

Jan 1, 1959

Thallous chloride and cadmium metal were recovered from a thallium-cadmium concentrate by a method suited to the treatment of small batches. Differences in oxide solubility and control of pH were employed to separate the thallium and cadmium. The cadmium metal produced by zinc reduction analysed better than 99.95 per cent Cd and thallous chloride of high purity was precipitated from solution.

Jan 1, 1969

By Dennis E. Mitchell

The need to develop and field explosive, pyrotechnic and propellant initiating systems that have high reliability and extraordinary safety requirements has led to the exploration and development of several materials and initiation systems at our laboratories. Our approach to initiating device development encompasses five main areas; energetic materials development , device physics, theoretical analysis and model development and experimental verifications

Jan 1, 1995

By AIME AIME

PLANS for the Semi-centennial Meeting have almost reached completion, although in any undertaking of such magnitude a few changes are always to be expected at the last moment. As worked out up to the time of going to press, the program of the meeting is shown below. The headquarters will be the Irem Temple, in Wilkes-Barre.

Jan 1, 1921

By Orr C. W

Continuing the systematic investigation of the influence of elements on the properties of lead(1). If the effects of additions of copper (up to 0.3%) on Port Pirie lead have now been determined in so far as creep rate is concerned.The results in the present paper contain also a survey of the influence of copper on the micro-structure of lead, a feature which has not appeared in the previous papers of this series. Further, it has now become known that creep is but little related to the more usually determined properties such as hardness and tensile strength. Since, however, these properties are of considerable importance in connection with the fabrication and use of this metal. Brinell hardness determinations have also been made and are here included.It is becoming more and more realised also that to be useful, creep data should refer to stresses of the order of those used in practice. This is due to the fact that as soon as deformation takes place, the properties of the metal are automatically changed. Lead does, of course, creep during industrial use, and probably (in lead chamber construction for example) extensions of the order of 5%...

Jan 1, 1938