Search Documents

By H. A. Kendall, W. C. Goins

Several investigations in recent years have shown that drilling rates are increased significantly with increased hydraulic horsepower. But, there has been no over-all method of designing jet-bit programs that efficiently uses the surface power. A study of present practices indicates that frequently as little as 50 per cent of the possible effects at the bit are used. Some observers have indicated that the best utilization of hydraulic horsepower (maximum effect on drilling rate) occurs when the bit hydraulic horsepower is maximum; others have stated that jet impact force is more important, and others have believed that maximum jet velocity is required. Limited efforts to date have shown some optimum conditions for bit hydraulic horsepower and impact, but these conditions cannot exist during drilling of a large part of the hole and do not provide a basis for designing a complete jet-bit program. This paper shows the maximum obtainable bit horsepower, impact force and jet velocity at all depths, taking into account the limitations of the pump, piping, hole and minimum circulating rate for adequate cuttings removal. Ranges of operation are developed; and flow rates, surface pressure and bit pressures are specified for each range to provide a maximum of any one of the desired effects. It also is shown that, by proper selection of nozzle sizes and by following the rules presented, the maximum obtainable quantities can be effectively utilized from surface to total depth. Finally, a simple graphical method of selecting nozzle sizes and flow rates is presented which can be used with familiar bit-company hydraulic tables and calculators to design jet-bit programs for maximum bit hydraulic horsepower, impact or jet velocity, as desired. These programs make most effective use of the pumps. Heretofore, there was no method available for designing field tests which adequately separated the effects of bit horsepower, impact and jet velocity. The programs and procedures developed in the paper are dissimilar and, when used in future field testing, should demonstrate which program is the most important in obtaining the fastest drilling rate. INTRODUCTION During the past decade, rig hydraulics has come into increasing prominence. There has been a definite trend toward providing higher horsepower pumps, jet-type bits have had increased use, numerous investigators"" have reported increased drilling rates as a result of increased hydraulics, and bit manufacturers have provided tablesa-" and calculators that are now commonly used 10 design jet-bit programs. Opinion has varied as to the hydraulic quantity which has the great- est effect on drilling rate. Papers and data have been presented that show pump horsepower,'9 it hydraulic horsepower and jet impact force,' each to be the most significant factor affecting drilling rate. Examinatibn of jet-bit programs of the bit companies indicates emphasis on jet velocity. Only pump horsepower can be eliminated because it can be used to produce any one of the bit effects which, a priori, must be more relevant factors. This contradictory state of opinion and practice regarding the bit effects is unfortunate, but several published references have been concerned with making one or another of the factors maximum; and, because these in each case have given results applicable to only intervals of the hole drilled, there seems to be ample reason to complete the previous efforts. It also is believed that the differences in programs for each effect, where they exist, should be delineated so that future use may determine which hydraulic effect is the more relevant. It is the purpose of this paper to: (1) show the theoretical maximum bit hydraulic horsepower, jet impact force and jet velocity available at all depths, taking into consideration all necessary restrictions on operating conditions; (2) illustrate procedures by which the maximum available horsepower, impact force or veIocity may be obtained; and (3) present a graphical method for rapid selection of jet-nozzle sizes and flow rates to be used with conventional procedures to design jet-bit programs for maximum bit horsepower, impact force or velocity as desired.

By Fred C. Bond

There is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool [or the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1943

By Fred C. Bond

There is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool [or the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1943

By Donald W. Scott

THE year just ended was the 50th anniversary of that first flight at Kittyhawk, N. C., in 1903. In this 50-year period the aviation industry made startling developments from flight distances of 120 ft-at snail's pace-to speeds of over 1300 mph and flights that circle the globe. And 1953 also was the 50th anniversary of the Utah Copper Co., the Father of our mass production porphyry copper ventures. How do developments in the mining industry stack up with the aviation industry? The mineral industry can be as proud of developments over the past 50 years as the aviation industry. Only for the developments of the mineral industry could aviation and other allied industries advance as they have. The year 1953 made its contribution to this progress, with the normal number of process and equipment developments and an abnormally high amount of activity in new plant capacity, particularly copper. Tonnages are on the increase and operating troubles are becoming more and more problems in materials handling and control. We're approaching molecular dissemination of ores with hydro and pyro methods coming to the front to take over where flotation leaves off.

Jan 2, 1954

By S. M. Matthews, D. J. Maconochie, L. G. Alexander, V. H. Tillmann

Case studies of the behaviour of large open stopes at the New Broken Hill Consolidated Mine, Broken Hill and the CSA Mine, Cobar, N.S.W. are considered. Deformations were measured by multipoint rod extensometers in sufficient detail to note the phases of rock behaviour, from intact through to rock-fall. In one case readings were obtained from a zone of stress failure in which two bumps, felt as ground tremors, occurred. In this case noise and stress were also monitored. Deformations were analysed in relation to previously measured in situ rock stress, and conclusions drawn about the degree of conformity to, and the areas of departure from, elastic model behaviour. Attempts to describe the growth of instability utilize reduction factors of the apparent modulus, a magnification factor for the apparent Poisson's ratio, and a correlation between progressive noise count and displacement. Monitoring itself is seen as an aid in determiing the final dimensions of stopes and pillars. One large stope, of intermediate dimension 80 m, was mined essentially without change of plan, whereas a change in mining plan was necessary in other stopes. Aspects of interest to mine planners, and areas where futher research is needed, are indicated.

Jan 1, 1981

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period May 10 to June 10: Rene de Sallier, New York, N. Y. Karl Koelle, San Luis Potosi, Mexico. H. S. Chamberlain, Chattanooga, Tenn. W. A. Wilson, Salt Lake City, Utah. F. R. Pretyman, Oyster Bay, N. Y. P. E. Barbour, Candor, N. C. R. Eustice, South Australia. R. C. Blanchard, London, England. F. C. Darby, South Australia. S. K. Tong, Shanghai, China. Grant H. Tod, Livermore, Cal. W. T. Burns, Great Falls, Mont. J. Murray Clark, Toronto, Canada. F. W. Bacorn, Butte, Mont. J. H. Adams, Birmingham, Ala. H. B. Pulsifer, Chicago, 111. A. Faison Dixon, Encontrador, Venezuela. Dwight E. Woodbridge, Duluth, Minn. C. W. Merrill, San Francisco, Cal. Heinrich Ries, Ithaca, N. Y. Francis Church Lincoln, Boston, Mass. H. L. Slosson, San Francisco, Cal. Frank R. Corwin has severed his connection with the Arizona Copper Co., Clifton, Ariz., and is now shift superintendent at the smelting plant of the Copper Queen Consolidated Mining Co.. Douglas. Ariz.

Jan 7, 1914

The new, internationally-owned Savage River Mines iron ore mining, concentrating and pelletizing project, built and operated by Pickands Mather & Co. International, was dedicated March 6 at Port Latta, Tasmania, Australia. Construction of the $79 million project began in 1965 and involved an open pit mine and concentrating plant plus a complete town for about 350 employees at Savage River; a 53-mile pipeline to transport the concentrates; a pelletizing plant and shipping facilities at Port Latta, which is on Bass Strait separating Tasmania from the Australian mainland. The project has a rated capacity of 2.25 million Ltpy of high-grade magnetite pellets, which will be sold to five Japanese steel companies under 20-year contracts. The open pit mine is located in the central portion of the Savage River deposits. Mining equipment, capable of moving 10 million tpy of ore and overburden, consists of four 6-cu yd electric shovels and 12 50-ton trucks. The concentrating plant, with a design capacity of 5 million tpy of ore, will use magnetic separators to upgrade the ore, which averages 38% iron, to a concentrate averaging 67% iron.

Jan 4, 1968

By Plato Malozemoff

Our young, technically oriented people today are entranced by the space program, by physics that unlocks the secrets of nature, by electronics, and by other new technologies. The mining industry seems to be their last choice. Enrollment in mining schools is dropping and so is the interest of our great universities in mining curricula. The image of the mining industry appears to be one of being conservative, nonprogressive, resistant to change, and lacking in excitement and challenge. I submit that this public image is wrong. While the initial development of mines is usually slow and seemingly plodding, the problem of solving the imponderables of nature-the ore emplacement, its structure and physical characteristics, its response to recovery processes, and its probable ultimate profitability-is stimulating to the most acute and searching of minds and requires careful application of a combination of many technologies. The paths to obtaining the desired results must be within the bounds of reasonable expenditures in the early stage of development when risks are still high, and this financial discipline is a further stimulus to the imaginative search for the right answers.

Jan 6, 1968

By B. C. Scott, A. Baker

The Pitch mine of Pinnacle Exploration, Inc. is in the Marshall Pass district, thirty miles east of Gunnison, Colorado. This is a new mining district, having come into existence as recently as 1955, when uranium mineralization was discovered rather late in the days of the uranium boom. There have been three other mines in the district, all of them now inactive. Two of these produced a few hundred tons of very high-grade uranium ore, and the third, Pinnacle's Little Indian 36 mine, produced a few thou- sand tons of lower grade ore. Pinnacle was one of the first companies in the district, and was able to acquire a large acreage. The first two years of exploration were essentially wasted in looking for Plateau-type deposits in a mineralized sandstone bed, but this "wasted" work produced two specific items that paid off. One was an ore-grade outcrop that ultimately became the Little Indian 36 mine, and the other was a boulder of very high-grade uranium ore that eventually led to the discovery of the Pitch mine; however, the actual source of the boulder still has not been found.

Jan 5, 1961

By H. W. Norman

DURING the first few years of the new atomic age the Colorado Plateau was the focal point of uranium exploration. There was little incentive to expend time and effort in an area so far removed from the known deposits as the Pacific Northwest, and there were too few local prospectors to cover the vast territory involved. In 1949 the AEC established an exploration office in Spokane to evaluate the uranium potential of the northwestern states. Interesting occurrences were found in the Coeur d'Alene district in Idaho and in the Boulder Batholith of central Montana, but the AEC discontinued the Spokane office in 1952, and for the next two years prospecting in the area was negligible. In April 1954 John and James LeBret, prospecting on the Spokane Indian Reservation with an ultra violet lamp, located an occurrence of the fluorescent uranium mineral autunite. This discovery was not announced until the following September, after a lease had been granted by the Spokane tribe. Exploratory drilling carried on by the AEC throughout the winter verified the existence of a commercial orebody. This property, the Midnite mine, has since developed the largest known ore reserve in the district.

Jan 6, 1957

By Arthur Foote

AT THE end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping Southwest, or, exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North. Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a North-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly.

Jan 1, 1930

By W. J. Keep

We have shown in former papers the influence which aluminum exerts when added to cast-iron, and we have presented in another paper, accompanying this one, the physical properties of the metal aluminum and of some of its alloys. The present paper continues the investigation. The reader will find, in our paper on "Aluminum and Other Metals Compared,"* explanations not here repeated, which will render the diagrams in this paper intelligible. The scale of stresses is laid off on the ordinate which rises from the zero-point of the diagram. The scale of deflections is laid off on the abscissa which runs horizontally through this zero-point. By applying a given amount of stress, then running back to zero, and again applying the same stress, we describe a spring-line, in which the deflections are proportional to the stresses. Generally the deflections exceed this proportion during the original application of stress; and the excess is the permanent set. By laying off from the zero-point a line parallel to the springline, we shall generally find that this new spring-line and the diagram coincide for some distance; that is, that the test-bar is

Jan 1, 1890

By W. N. Best

Crude oil attracted attention because of its excellence as a fuel for openhearth furnaoes; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hotair furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This mcans a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity BaumB. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230". F., Mexican crude oil at from 175" to 210" F., and Beaumont, Texas, oil at 142" F. Fuel oil vaporizes at 130" F. Scientific Installation Essential The burning of oil is an art based on science, and the "rule of thumb" should never be employed, especially in heating heavy crude oil. Thermometers should be used on both suction and supply pipes so that the fireman or smith will at all times know the temperature of the fuel. The indicators on such thermometers should be large enough to be readily seen by the operator, night or day. It is necessary to have an unvarying pressure of steam or air through the burner, to atomize the fuel. Also, the air used to support combustion should be delivered through a nozzle under the burner at a constant pressure. The oil pressure must not fluctuate; under no eircumstances should it vary more than 1 1b. The oil pump, which should be brass-lined, with the aid of the pulsometer and superheater, will insure a constant

Jan 1, 1916

By Ira N. Holli

A meeting of Engineering Council was held on Thursday, Jan. 22, 1918, at the Engineering Societies Building, New York. Present: Chairman Ira N. Hollis (A. S. M. E.); Dr. Charles Warren Hunt, Alex. C. Humphreys and F. H. Newell (A. S. C. E.); B. B. Lawrence and .J. Parke Charming (A. I. M. E.); Charles Whiting Baker, D. S. Jacobus, and George, J. Foran (A. S. M. E.) ; H. W. Buck, E. W. Rice, Jr., N. A. Carle, C. E. Skinner and Comfort A. Adams (A. I. E. E.) ; Clemens Herschel and Calvert Townley (United Engineering Society); also, by invitation, D. W. Brunton, Chairman, War Committee of Technical Societies of Engineering Council. Of the several actions taken at this meeting, the following are selected as being of most general interest. Chairman-Baker-presented a resolution on the conduct of the war, to which objections were made. It was referred to a special-committee; Charles Whiting Baker, Charles Warren Hunt, and Calvert Townley, for re-drafting and presentation later in the meeting. The revised resolution submitted by this committee led to further discussion and as no agreement could he reached, the matter was laid on the table.

Jan 3, 1918

By Joseph Kelly

DEPLETION of anthracite resources in Lackawanna County, Pennsylvania, has forced the recovery of coal tracts formerly considered unminable. Chief among these are the large areas of outcrop coal lying on a heavy pitch on the mountain sides, abandoned thirty or forty years ago as too costly and too hazardous to mine. The old companies, in many instances, stopped their chambers 80 or 100 ft. hack from the actual outcrop, and then dropped back another 100 ft. before starting to rob the pillars, thus leaving large areas of coal. Recovery of this coal naturally leads to mining hazards not encountered years ago. The first step is to sink a slope from the surface with the pitch of the vein, and then drive counters across the pitch as close to the robbed area as proper protection for the lower side of the -counter will permit. Next, the old chambers are advanced or new ones driven in the solid, as the conditions require. As these chambers approach the outcrop the real safety work begins-that of preventing the miner from being buried or locked in by an avalanche of mud.

Jan 1, 1936

By J. McD. Porter

In many of the old placer-mining districts are still to be found large tracts of gold-bearing gravel not suitable to be worked with a dredge, because the bed is too shallow or the gulch too narrow. Frequently there is not enough grade to handle the gravel successfully by ground-sluicing or a bedrock flume, or it contains too many boulders to be worked succeeefully with the ordinary hydraulic pipe or tube elevator. In southwestern Oregon, two practical placer-miners named Ruble, after working for years trying to make money out of placer-ground coutaining many large boulders, invented and patented a hydraulic elevator of an entirely new type, and one that has been found to work very successfully in flat ground and in gravel containing many large boulders. It is a very simple contrivance. A few years ago I acquired the property near Pierce City, Idaho, known as the American placer-mine. Various attempts had been made to work this ground. A bed-rock flume had been installed by one company, an Evans elevator by another, and still other methods were tried on a smaller scale. All were

Jan 1, 1910

By GEORGE W. HARHIS

IN the earlier period of anthracite-ruining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally operated under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit only. They were- not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes ; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation wits given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.` That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Nov 1, 1905

By Harlowe Hardinge

THE sound made by ball, pebble and rod mills has long been used by the operator as the "telltale " of their operation. The nature of this sound depends upon local conditions and the type of mill used. By experience an operator can tell whether the mill is running properly or not. Some operators are able to detect the difference in sound much better than others and get better results running the same mill under the same conditions. The automatic operation of a mill using sound as the fundamental means for maintaining control presents many problems. The satisfactory solution of these problems requires, for given operating conditions, a greater average output, with improved product for subsequent processing, than can be obtained by manual control. RELATION OF SOUND TO USEFUL GRINDING ENERGY Experience has taught us that there is a difference in character as well as in intensity of sound between a mill grinding wet and one grinding dry, in open or closed circuit, to obtain a coarse or fine product, on the same material, to say nothing of the effect with a variety of different materials. Broadly speaking, a wet-grinding mill operates best at a lower sound level than the same mill grinding dry, with other conditions the same. Several reasons for this variation in sound intensity under these conditions can be advanced, but the important point is that there is a difference, based upon practical results. Since these reasons may be more or less involved, and may be subject to much discussion, only one will be considered here. It is apparent that two balls hitting together or a ball striking the lining, if there is no intervening material, will produce the maximum sound. If a complete cushion of material is placed between the balls or ball and liner, so that the energy is dissipated without doing useful work, the balls will be unable to create enough pressure or force to fracture the particles, and the sound will be at a minimum. At some point in between-that is, where there is sufficient material between the balls or ball and liner so that the ball will fracture the particles without mashing them unduly-the sound

Jan 1, 1939

By R. R. Hoffman

The name L'brush,l as applied to the parts to be briefly considered in this paper, is not clearly descriptive of the design and function of those parts when the usual definition of the word is applied. In a general way, the brushes to be considered here are the parts employed on certain types of electrical equipment to facilitate the transfer of electrical current between a rotating or moving element and a stationary element. These machines are generally motors and generators of both the slip-ring and commutator types, rotary converters, battery charges, etc. Parts that serve a similar purpose on relatively slow or intermittently moving devices such as rheostats, switches, controllers, etc., are generally referred to as contacts. A few special applications involve the use of current-carrying washers, rollers, bushings, etc. As may be inferred, therefore, the design of these brushes and allied parts is dictated by both electrical and mechanical considerations. In most cases these factors are closely interrelated, and unfortunately many of them are not subject to exact scientific or mathematical analysis. Special Advantages Since brushes operating on direct-current machines must carry the load current, resist destructive action from voltage induced in imperfectly compensated armature coils, and in addition act as a bearing material, maintaining intimate contact with the commutator at peripheral speed, which may be as high as 70 miles per hour it is difficult to obtain in one brush the ideal properties necessary for perfect functioning under all operating conditions. The engineer-designer, therefore, when selecting a brush for a specific application, must choose a grade that possesses the characteristics most adequate to meet the conditions involved. In many cases a characteristic that makes a specific grade of brush the ideal selection for one type of machine may be of secondary importance to some other property when the brush is applied on another machine. Frequently different grades of brushes must be applied to the same type of machines when they operate under different or unusual atmospheric conditions. Completely satisfactory brush operation depends on freedom from appreciable sparking, minimum electrical and mechanical losses, negligible commutator or slip-ring wear, uniform film over the commutator or slip ring, quiet operation and good brush life. The ability to produce special structures, and to combine in widely varying proportions materials that are incompatible, through conventional melting and alloying procedures has been the basic contribution of powder metallurgy to the solution of problems involving brushes and allied parts. This is especially true where current-carrying capacity is a major factor, owing to the limitations of all carbon or all graphite brushes in that respect. Metal-graphite Brushes With very few exceptions, friction between moving elements. across which

Jan 1, 1945

By Peter J. Lean

The introduction oE computer control in the grinding circuit of the New Broken Hill Consolidated Limited concentrator in the early 1970's gave smoother operation at optimum performance. The ore feedrate and water additions to the grinding circuit were controlled to operate each of the ball mill/ rake classifier grinding units at the upper limit of the circulating load while classifier overflow density was maintained to give a product size and pulp density suitable for flotation. An incremental expansion of the concentrator in 1981-82 included the installation of hydrocyclones in closed circuit with three of the four ball mills. Without the rake classifiers in circuit the previous control strategy could not be used and the complex interaction of hydrocyclone performance characteristics when classifying coarse grained sulphide ore resulted in the over-grinding of the lead mineral galena. Testwork aimed at optimising grinding circuit performance recognised the enhanced tendency of higher specific gravity minerals to report to the cyclone underflow. The data has been evaluated on an individual mineral basis and then used to develop a model For grinding circuit control. The development of the model which uses inputs of ore feedrate, metal content of the Feed and slurry density of the cyclone overflow to predict the size of the minerals in the grinding circuit product is described and model predictions are compared with plant performance.

Jan 1, 1984