Search Documents

By Jean Howard, E. V. Walker

ManY papers have been published during the last few years on the formation of cube texture in 3 1/4 pct Si-Fe, e.g., those of Assmus, Detert, Dunn, and Walter.1,5 All are concerned with the formation of the texture by a process involving secondary re-crystallization and the relative surface energies of (100) and other planes under certain conditions of annealing. The authors have found that cube texture can also be produced by heavily cold rolling strip in which the cube-on-edge texture has first been formed. Cube texture develops on annealing, but in this case it is not accompanied by secondary recrystallization. The starting material is a sintered compact, the preparation of which has been described elsewhere. Using a conventional processing schedule employed for producing commercial silicon-iron with the cube-on-edge texture, the sintered compact is cold rolled to such a thickness that, after annealing in pure hydrogen for 24 hr at 1350'~ to produce the cube-on-edge texture, the final thickness required can be obtained by giving a further cold reduction of 85 pct. Cube texture is developed by annealing at -900~~ in pure hydrogen: it has been produced in strip up to 0.024 in. thick. The microstructure of the strip consists of a mass of small primary grains within the boundaries of the much larger secondary grains which ex- hibited cube-on-edge texture before the final cold roll. If the strip is annealed at -1000 after the 85pct reduction, secondary recrystallization begins to take place, provided a strong cube texture is present. On raising the temperature more secondaries grow, complete secondary recrystallization being obtained on annealing at -1150'. From this it is concluded that the secondary crystals are produced by the texture inhibition mechanism: they show (110) and (111) planes in the surface of the strip, the former being the more numerous. It has been observed that the more perfect is the (110) [001] texture prior to cold rolling by 85 pct, the further from the ideal is the (100) [oo].] texture. A similar treatment applied to high quality commercial grain-oriented silicon-iron strip failed to produce cube texture. The tilt and rotation of the [loo] from the rolling direction was less than 10deg, but (to within a few degrees) the planes (130), (450) and (210) lay in the surface of the strip. Acknowledgment is made to the Engineer-in-Chief of the British Post Office for permission to use the information contained in this note.

Jan 1, 1962

By F. J. Mehringer, C. W. MacGregor

VARIOUS investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-12 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q') values mentioned above for the tension test are defined by1 [ ] where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. PRELIMINARY INVESTIGATIONS The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 019 per cent; S, 0. 118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Elect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945

By E.G. Lewis, l.M. Barker

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

By L. M. Barker, E. G. Lewis

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the' second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson' argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

By Charles Catlett

My attention having been called several years ago to the possibility of increasing the yield of coke per ton of coal, as obtained in certain bee-hive ovens, I called the attention of the Institute to the matter at the New York meeting in 1899. I have had occasion since to witness the indifference with which this matter is ordinarily considered, and, on the other hand, the marked improvement which comes from even a most perfunctory effort in that direction; and I am almost tempted to say that nothing in connection with the coking of coal is at present so important. There are other factors, which are fundamental and necessary; but they have been considered already ; while the question of yield is, as a rule, absolutely ignored, or some figure is taken as the result of a special burning of one or two ovens, and the assumption is made that the whole battery is yielding at that rate. The uncertainty of this assumption I may illustrate by saying that, in my own observation, the burning of a single oven in a battery frequently gives, by actual weight, as much as 69 or 70 per cent. of merchantable coke, while the battery as a whole was yielding only an average of 63 per cent. Only from careful records, checked at least once a month, of the weight of the coal going to the ovens and the weight of coke produced, can any correct idea of the actual yield be gained, or methods be modified so as to produce good results; yet, as a rule, the crudest estimates are usually the only available data. In many cases there are reasons for this loose practice. The coal is mined by measurement; the payment for drawing the ovens is in proportion to the amount of cod which goes to them; and, not uncommonly, the royalty is so much a ton of coke, not of coal. The mine-manager is tempted to increase the volume of coal mined which is paid for as a ton, and to do the same thing in charging the ovens. Nor does he

Jan 1, 1903

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry's use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel 'economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry's use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel 'economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By R. L. Huntington, Frank P. Vance, George F. Russell, Robert Thompson

With the advent of higher pressures in the operation of natural-gas transmission lines, the removal of water vapor from the gas has become increasingly important in order to prevent condensation or formation of gas hydrate from slowing down or stopping the flow of gas. Intelligent design of these dehydration or gas-drying plants has been hampered through the Iack of experimental data on the water vapor content of natural gas at elevated pressures. In view of this need, this present investigation was sponsored by the Southern Natural Gas Co. in the Chemical Engineering laboratories at the University of Oklahoma Research Institute. Experimental results were obtained on the water-vapor content of natural gas up to 2000 lb. per sq. in. at atmospheric temperatures. The water content at 2000 lb. is approximately two thirds as much as it is at 1000 Ib. Deviations from the ideal gas laws vary directly with pressure and indirectly with temperature. Introduction The removal of water vapor from natural gas is an important operation in connection with the production and transportation of this commodity because: I. Liquid water accelerates internal corrosion of a pipe line. 2. Accumulation of water at low points in a pipe line reduces markedly its capacity. 3. Gas hydrates, icy snowlike growths, form readily under high pressure in the presence of the lower hydrocarbons and water, often plugging up the pipe line. In order to design dehydration plants for stripping the gas of its water content, it is essential that the engineer. have a knowledge of the saturated or equilibrium water-vapor content of the gas to be processed. With the gradual increase of operating pressures around gas-producing wells and pipe lines, it was observed that the quantity of water recovered from dehydration plants or condensed in colder lines was considerably greater than had been expected from calculated contents, based on vapor-pressure data taken from steam tables. This observation prompted a number of investigators, for instance, Laulhere,3 Dea-ton,l and Hammerschmidt2 to carry out experimental work at pressures up to 600 lb. per sq. in. in order to determine quantitatively the water content of various gases. Sage, Lacey, et al.4,5 have recognized more recently the need for such data at higher pressures, but their work was done at temperatures of 100ºF, and higher. Since hydrate formation usually, if not entirely, occurs at temperatures below 100ºF., the present investigation was confined to the . lower temperature range at pressures from 600 to 2000 lb. per sq. in. gauge.

Jan 1, 1945

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By C. F. Weinaug

In recent years, several methods have been proposed for correlation of physical properties and behavior of hydrocarbon systems. These correlations were found to be unsatis. factory for predicting differential gas liberation and shrinkage data now obtained experimentally. To achieve the desired accuracy, methods were developed to adjust the correlations with two experimental pieces of data. The required data are the saturation pressure at reservoir temperature and the specific volume or density at these conditions. The saturation pressure is used to adjust the vapor-liquid equilibrium-ratio correlations. The density measurement is used to determine the apparent density of liquid methane. With these adjustments, differential gas liberation and shrinkage are predicted within the experimental error. EQUILIBRIUM RATIOS Equilibrium ratios published by the National Gas Assn. of America' were used as a basis for the calculation. The convergence pressure for the sample was determined by using a hypothetical binary system, with methane as one component and the remainder of the system lumped together to form the other component. For the critical temperature of the heavy constituent, the weight average of the critical temperatures of the ethane and heavier components was used. The correlation of pseudo-critical temperature, density and molecular weight of Matthews, Roland and Katzl was used in this calculation for the hexane and heavier fractions. Points for the critical properties of methane and the hypothetical heavy constituent were placed on a chart of the critical loci of hydrocarbon systems. A critical loci for the hypothetical binary system was drawn, and the critical pressure of this system was determined at the reservoir temperature. This critical pressure became the convergence pressure for which equilibrium ratios were read from the NGAA4 charts. The NGAA equilibrium constants for C, through C, were used for the C,; through C, fractions since they were separated on the bases of normal paraffin boiling points. The correlation of Hoffman, Crump and Hocott5 as used to estimate the equilibrium constant for the C fraction. The NGAA eauilibrium-ratio charts are based primarily on paraffin systems and have to be corrected for the presence of naphthenes and aromatics. The correlations in the literature proved too unsatisfactory for determining these corrections. EXperimental data, the saturation pressure, is used with the correlation of Soloman2 to make this adjustment. The correction factors of Soloman were cross-plotted so that the factors for ethane and heavier components were made a function of the factor for methane. a2 = 0.7927 at + 0.1646 .........(1) where a, = correction coefficient for for methane NGAA equilibrium ratio, and a2t = correction coefficient for ethane and heavier NGAA equilibrium ratios. This equation and the equation for the bubble point are solved simultaneously for the correction coefficients. The bubble-point equation is anKnXn = 1.0 . . . . (2) The equilibrium constant for the saturation pressure at reservoir temperature is used. This procedure not only corrects for the relative volatility between components, but also assures that the results will be directly related to the experimental saturation pressure. METHANE DENSITY After determining a set of equilibrium ratios, the apparent density of condensed methane at 60°F and 14.7 psia was estimated. This was found to be necessary because the correlations of Standing3 ere found to be unsatisfactory. The law of additive volumes was employed to make this calculation.

For his achievement in building the Panama Canal, Major-Gen. George W. Goethals was presented, on May 22, the John Fritz medal, the highest mark of distinction in the engineering profession. In the absence, in Europe, of Clemens Herschel, chairman of the Board of Award, Charles F. Rand presided over the meeting. Col. John J. Carty, who was chairman of the Board of Award at the time the medal was awarded to Gen. Goethals, and who ordinarily would have presented the medal, was detained in Paris by Government work, so the presentation was made by Ambrose Swasey. When calling the assembly to order, the Chairman said: This medal has been awarded by a Board representing four of the National Engineering Societies: American Institute of Mining and Metallurgical Engineers, American Society of Civil Engineers, American Society of Mechanical Engineers, and American Institute of Electrical Engineers. The medal was established in 1902, in honor of that great American engineer, John Fritz, and has never been awarded except to very distinguished men. In. 1902, the first award was made to John Fritz for scientific and industrial achievement. In 1905, to Lord Kelvin for his work in cable telegraphy and other scientific attainments. In 1906, to George Westinghouse for the invention and development of the air brake. In 1907, to Alexander Graham Bell for the invention and introduction of the telephone. In 1908, to Thomas A. Edison for the invention of the duplex and quadruplex telegraph, the phonograph, the development of a commercially practical incandescent lamp, the development of a complete system of electric lighting, including dynamos, regulating devices, underground system protective devices and meters. In 1909, to Charles T. Porter for his work in advancing the knowledge of steam engineering and in improvements in engine construction. In 1910, to Alfred Noble for notable achievements as a civil engineer. In 1911, to Sir William H. White for notable achievements in naval architecture. In 1912, to Robert W. Hunt for his contributions to the early development of the Bessemer process. In 1914, to Professor John E. Sweet for his achievements in machine design. In 1915, to Dr. James Douglas for notable achievement in mining, metallurgy, education, and industrial welfare. In 1916, to Dr. Elihu Thomson for achievement in electrical invention, in electrical engineering and industrial development, and in scientific research. In. 1917, to Dr. Henry M. Howe for his investigations in metallurgy, especially in the metallography of iron and steel. In 1918, to J. Waldo Smith for achievement as engineer in providing the City of New York with a supply of water. And now to General Goethals for achievement as the builder of the Panama Canal_

Jan 7, 1919

By R. J. Charles, G. Agar

Experiments on single particles show that the amount of material created during impact that is finer than any chosen size is proportional to the energy of the impact. As the underlying principle of comminution, it might be stated that each unit of energy input to a given comminution system tends to add to the system an identical assembly of new particles and subtract an equivalent volume of larger particles. Thus, two of the consequences of the fact that each unit of energy tends to add identical assemblies of new particles to the system are: 1) on continued application of energy the total charge in any batch comminution system tends to assume the characteristics of this assembly, and 2) the process of comminution may be described by a relationship such as E = Ak-a. Recently Schuhmannl presented a theory of comminution which puts rational perspective on the extensive controversy surrounding most of the existent theories of comminution. With hindsight the origin of controversy can be ascribed to a relatively simple circumstance. In general, a progressive shift of a size distribution curve towards finer sizes is observed as energy is added to a comminution system. It is also observed that, with continued grinding, the size distribution curves usually change and appear to approach some constant shape. Inves-tigators generally felt that an appropriate method of relating and generalizing such data would be to consider the hypothetical case where particles in the system were uniformly subjected to comminution such that each of these particles, receiving its proportion of input energy, was transformed into a number of smaller particles of uniform size. Since the changes in shape of the size distribution curves during size reduction were clearly associated with the coarse particles in the system, it was also assumed that these changes accounted for little of the input energy and one could deal solely with the equilibrium shape towards which the size distribution curves tended. Although the unrealistic nature of the foregoing points of view was realized some justification was felt for such treatments since, in most cases, the resulting mathematical formulae could, by the adjustment of at most two parameters, satisfactorily describe experimental observation. Difficulties arose, however, in that the formulae required a specific influence of the feed size on the comminution process. In actual fact, the application of a feed size term in fitting experimental data was often found to be unnecessary or contrary to the above formulae. Secondarily, much discussion arose concerning the appropriate energy number that would relate the size change of one particle to the amount of comminution energy it received. As has been previously shown3 all the above theories that treat comminution as a continuous process of size reduction may be related to a proposition of the following form: dE = -Cfn [1] where dE is the increment of energy, dx is the size change, x is the particle size, and C and n are constants. It is now clear, as pointed out by Schuhmann, that Eq. 1 is inapplicable to comminution processes, since comminution cannot be considered other than as a discontinuous mixing process in which the overall size distribution of the product results from mixing, in various proportions, finished material with unfinished, and sometimes untouched, material. A striking illustration of this mixing phenomena may be obtained by comparing the size distributions of grinds in a typical batch ball mill with size distributions calculated on the basis of mixing various proportions of feed material with a ground material which obeys a power law size distribution relationship. Figs. la and lb illustrate such a comparison and the similarity of these figures indicates that mixing plays an important role in determining the overall shape of the product size distributions. Figs. la and lb illustrate, additionally, the underlying basis of the comminution theory presented by Schuhmann.' In the preliminary grinding of relatively close sized feed particles in a batch ball mill, one may visualize that, when a successful encounter of a ball with a feed particle occurs, then the particle undergoes severe size reduction and the size range in which the resultant particles reside is far removed from the size of the feed particles. After a number of feed particles are reduced by independent but similar impacts and one examines the size dis-

Jan 1, 1961

By Charles C. Towle, Irving Rapaport

URANIUM mineralization along the north flank of the Zuni Uplift, in the vicinity of Haystack Butte, was discovered by Paddy Martinez, a Navajo Indian, in the spring of 1950. The find was reported to the Santa Fe Railway Co., which initiated a program of exploration upon its holdings in the district in December of 1950. The Anaconda Copper Mining Co. secured numerous leases in January and February, 1951, and began an intensive exploration and development program in March 1951. The district was extended into the Lucero Uplift in August of 1951 by the discovery of uranium mineralization in Todilto limestone by Joy Sinyella, a Supai Indian living on the Laguna Reservation. Initial reconnaissance was performed in the district by the Atomic Energy Commission in November 1950. A field office under the direction of the Denver Exploration Branch of the AEC was established at Prewitt, N. Mex. in January 1951 to study regional and detailed guides to ore, to evaluate the ore deposits, and to promote the development of the district by providing geologic services for the companies and individuals engaged in exploration. With the development of sufficient ore to warrant construction of a mill, the Grants area of New Mexico has come of age as a full fledged uranium mining district. The carnotite-type deposits of Grants, the first of major economic importance found in limestone, have extended the Colorado Plateau carnotite field into the more complex structure of the Basin and Range Province. General Geology The Grants uranium district is in northwestern New Mexico, along the southern flank of the San Juan Basin, between the cities of Gallup and Albuquerque. The region is at a mean altitude of about 6800 ft, vegetation is sparse, and outcrops are excellent. Mt. Taylor volcanic peak, at an elevation of 11,400 ft dominates the surrounding area. The overlying cliff-forming Dakota sandstone is the most resistant formation in the Grants District and characteristically erodes into dissected mesas as much as five miles wide. The principle uranium ore-bearing horizons are found in the underlying Morrison formation, and the Todilto limestone of the San Rafael group. The Morrison weathers into. a series of steep slopes and precipitous cliffs near the lower part of the Dakota-capped rims, while in contrast, the relatively resistant underlying. Todilto [ ] limestone forms broad benches extending out from the base of these Dakota rims as much as five miles wide. The Todilto benches are covered with overburden to an average depth of about 5 ft in the first thousand ft away from the Dakota rim, but increases to about 200 ft at the base of the rim. In many places however, a thick mantle of upper Cretaceous sediments and Tertiary volcanics "obscures the ore-bearing Jurassic, and precludes exploration. . The known uranium deposits of the Grants District are distributed throughout a zone 85 miles long and about 10 miles wide. Stratigraphy Rocks from pre-Cambrian through Tertiary are exposed in the uplifted areas, but uranium appears to be restricted chiefly to two zones in Jurassic sediments. The Jurassic sediments of the Colorado Plateau have been subdivided into three units, in ascending order: (1) Glen Canyon group, (2) San Rafael group, (3) Morrison formation. The Todilto limestone zone within the San Rafael group has produced the bulk of ore to date, but the promise of the Morrison zone is rapidly increasing. The Todilto formation extends about 300 miles east-west and about 100 miles in a north-south direction. It is composed of a lower, extensive, limestone member and a central, more restricted, thick, pure gypsum member. The Todilto is believed to be of lacustrine origin. The Morrison formation in this area is subdivided, rather arbitrarily, into three members: Recapture Creek, Westwater Canyon, and Brushy Basin. Ore

Jan 1, 1952

By W. W. Gorr, R. Smith, E. H. Wyche

THE combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W? and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. DEVELOPMENT OF THE NEW STEEL For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield 18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators 'then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, o.58; Ni, 7.28; Cr, 17.6o; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1946

By Morris A. Steinberg

Because of the broad scope of my topic I will discuss my subject from the point of view of a present status of the metallic materials that are used in structures and will dwell primarily on those structures related to high- performance aerospace systems. Thus, I can best portray the status of these structural materials as related to existing transportation systems, delineating some of the highlights of alloy development, fabrication, and properties obtained. I shall point out what are, in my opinion, the needed solutions to pressing unsolved metallurgical problems connected with certain selected metals: aluminum alloys, beryllium, titanium, steels, superalloys, refractory metals and some metal-matrix composites. Aluminum Alloys For a number of years a series of strong aluminum alloys used for airframes has had an important bearing on the development of minimum- weight, highly efficient structures. Among these alloys are such familiar ones as 2024-T3, 2014-T6, 7075-T6, 7079-T6 and 7178-T6. A review of the development and use of strong aluminum alloys in aircraft structures indicates that before about 25 years ago there was very little application of products other than forgings in the high-strength tempers produced by precipitation heat treating to T6- or T8-type tempers. 1 As stated by Dix in 1944, "There has been a gradual evolution in engineering viewpoint regarding the mechanical characteristics which are required in a structural material suitable for aircraft. Formerly, emphasis was placed on a generous spread between yield and tensile strengths, on elongation, on impact strength and on resistance to corrosion. Aircraft structural engineers still differ widely as to the importance which they attach to these proper tie.” 2 It is fair to say that this evolution is still taking place, that the problem is much the same in 1970 as in 1944 - except that strength levels have advanced some - and the question remains as to how far we can go in that direction. In the meantime, a new group of alloys has received acceptance and widespread use. The first alloy of this group, 7075-T6, was formally introduced by Dix's 1944 paper. The drastic changes that have taken place in the size and configuration of components employed in air-

Jan 1, 1971

By L. K. Welch, C.W. Macgregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By L. K. Welch, C. W. MacGregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By H. F. Easter

The lead department of the El Paso Smelting Works at El Paso, Tex., is operated strictly on a custom basis. The ores treated are drawn from the surrounding territory, comprising New Mexico, Arizona, western Texas, and northern Mexico. Ores received from the last-named section originally amounted to a very large tonnage, but. of recent years have dwindled into comparative insignificance so far as this plant is concerned. This has been due partly to the establishment of a lead-smelting plant at Chihuahua, which is much closer than El Paso to most of the important mines, and partly to the recent revolutionary troubles in Mexico. There are no mines of either lcad or copper in the immediate vicinity of El Paso. In general, it may be said that the lead-ore supply of recent years has been uncertain and precarious, with a general tendency toward an excess of silica and a shortage of iron. This latter requirement has been met in large part by the use in El Paso lead furnaces of considerable amounts of roasted leady copper matte from the Chihuahua smeltery and of converter slag from the El Paso converters. These two materials, coupled with complex lead-copper ores from Bisbee, Ariz., have introduced into the lead-smelting operations a most unusual amount of copper, which has had an important bearing upon the smelting practice of the plant. his matter will be discussed later. The ore, loaded in either box cars or gondolas, enters the storage yard on four tracks elevated about 8 ft. above the ground. As all unloading is done by hand, unloading platforms at the height of the car floor parallel the tracks on each side to afford a runway for wheelbarrows. At frequent intervals these lengthwise platforms are joined together by others running crosswise to facilitate the distribution of the ores evenly over the beds, which are located below and between the tracks. At present much of the bedding space formerly used for lead ores is given over to the copper department, but 20 bins of various sizes are retained for the use of the lead furnaces and the Huntington & Heberlein roasting plant. The largest of these holds about 1,000 tons, while the smallest holds not over

Jan 1, 1916