Search Documents

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By Harold Margolin, W. R. Hibbard, R. W. Fenn, H. P. Moore

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By C. J. Fleisch, C. P. Clingerman

THE recent installation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. THE FURNACE PROPER A few of the characteristic points and dimensions of the furnace proper are: [Hearth diameter 26 ft. o in. Bosh diameter 29 ft. 1 3/4 in. Stock-line diameter 20 ft. o in. Large-bell diameter 114 ft. 8 in. Small-bell diameter 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed 94 ft. 4 in. Height of furnace from center of iron notch to main platform 105 ft. o in.] The furnace top is equipped with a McKee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. g in. in diameter, then through uptakes that are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. DUST CATCHER The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catcher is g ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is 50° with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas in-

Jan 1, 1943

By J. S. Seawright

Haulage is a costly feature in the operation of an open pit mine, whether it be iron, copper, or limestone. The National Iron Co. has adapted an old underground method to the open pit inclined skip haulage to bring the ore from the pit bottom to the crusher or beneficiation plant. The Rockover skip has been placed in operation where limited areas have retarded or eliminated use of long rail or road slopes. Deep and narrow orebodies subject to rapid increase in depth that discourage use of conveyor belts and necessary crushing plants are ideal for this system. The skip haulage method was developed to combine the desirable features of conveyor, truck, and rail haulage and at the same time avoid the draw- backs. The skip was designed to follow the natural angle of repose of the pit wall and can vary from 25° to 45°. Open-pit skips now in operation show that the installation is successful and provide the

Jun 1, 1955

By R. A. Sharma, F. D. Richardson

Manganese oxide acitivities and sulfide capacities have been measured at 1650°C in mixtures of MnO + A1203 and MnO + SiO2 - Al2O3. Sulfide capacities have also been measured at 165O0C for melts of MnO + SiO2, MgO + SiO2, MgO + SiO2 + Al2O3, MgO + MnO + SiO2, and SiO2 + Al2O3 and for crystalline CaO. The activity coefficients of the sulfides of manganese and magnesium have been derived where possible. It looks as though the activity coefficients of sulfides are greatest at compositions where the free energies of formation of the silicate mixtures have their maximum negative values. The amphoteric nature of alumina is reflected in the results for the binaries and ternaries in which it is present with silica. The limiting solubility of CaS in CaO at 1650°C is 6.3 x 10-4 mole fraction. THE activities of manganese oxide have been measured in a variety of silicate and aluminate melts by use of the equilibrium (MnO)slag = [Mn]pt .½O2 [l] and the experimental techniques described previously.' Sulfide capacities (CS = wt pct S (PO2/PS2)½) have also been determined in a series of melts, by use of an established method2 which exploits the equilibrium (O°) + ½S2 = (S") . ½O2 [2] If CS and the activity of a metal oxide are known in a melt, the activity coefficient of the metal sulfide can be calculated by use of the equilibrium constant K, for the pure phase reaction MO i ½S2 = MS + ½O2 [3] The activity coefficient of the sulfide is then given by the equation

Jan 1, 1965

By R. T. Southin

Cast ingots of 99.99 pct purity A1 and aluminum/copper alloys containing up to 2 pct Cu have been found to contain four zones rather than the three previously accepted, i.e., chill, colummar, and equiaxed zones. The fourth zone consists of a coarse dendritic layer across the top surface of the ingot which is open to the atmosphere. It is also found that the grains in the equiaxed region have a "cornet" shape, with a head which is coarsely dendritic and a tail which grew with the same structure as the columnar grains. Experiments using mechanical barriers, and others involving the elimination of the surface dendrile layer, have indicated that nucleation of the equiaxed zone is caused by the showering of dendritic particles from this surface dendrite layer. These particles are the dendritic heads found in the comet grains. A mechanism of nucleation and growth of these comet grains is put forward. Experiments with a number of other metals and alloys suggests that these conclusions may apply generally to ingots cast without the addition of nucleating agents, and solidified under normal conditions. THE macrostructure of cast ingots may contain the following three zones: i) a peripheral zone of fine equiaxed grains, commonly called the chill zone; ii) a zone of columnar grains extending inwards from the chill zone; iii) a central zone of equiaxed grains; these are normally larger than the chill grains. All three zones are not necessarily present in any particular ingot since their existence and magnitude depend upon the casting conditions and composition of the cast material. The mode of formation of zones i and ii is fairly well understood. However, the cause of the central equiaxed zone remains a matter of conjecture. Previous theories put forward to explain the mechanism of nucleation in the equiaxed zone have been examined by Chalmers1 and Winegard.2 At the time when the present work was carried out the most re -cent hypothesis was that due to Chalmers,1 who recognized more fully than previous workers that conditions in this zone during solidification were not conducive to nucleation. In his hypothesis, he suggested that nuclei were formed near the mould wall during the very early stages of solidification, and that they can drift into the central zone by convective motion. This was supported by evidence from experiments using mechanical barriers to stop the drift of nuclei. A similar hypothesis had previously been put forward by Genders.3 More recently, Jackson et al. 4 have observed that dendrite arms in organic compounds can melt off during solidification. They have postulated that this occurs in metals and alloys, and that the dendrite arms which have been freed from the main dendrite act as nuclei for the equiaxed zone. In the present work, critical metallographic examination has shown that there is a fourth zone in the macrostructure of cast ingots which is a dendritic layer over the top surface of the ingot. It is also shown that there is a relationship between this zone and nucleation of the equiaxed zone. EXPERIMENTAL DETAILS The alloys examined were prepared from super -purity aluminum of 99.99 pct min purity (spectro-graphically detected impurities of Cu, Fe, Si, and Mg) and copper of 99.98 pct min purity (spectrographically detected impurities of Si, Zn, As, Fe, Pb, Bi, Ni, Sn, Mn, Ag, Cr, and Al). Three compositions of ingots were examined, containing 0.0, 0.1, and 2 pct Cu, respectively. The alloys were melted in an alumina-lined salamander crucible using a medium-frequency electric induction furnace; when the appropriate casting temperature was reached, the alloys were cast without degassing or fluxing treatment. The mould used was made of electrode graphite and had the following dimensions: external diameter 6 in., height 9 in., with a mould cavity 8 in. deep and a diameter tapering from 5 in. at the top to 4 in. at the bottom. Casting temperatures used were generally in the order of 70" to 90°C above the liquidus and the mould was at room temperature before casting. Inserts kere placed in the mould cavity in some experiments. These consisted of either an 18-g stainless-steel tube of 2 in. diam held axially in the mould i in. off the bottom and extending 1 in. out of the top of the mould or a "trap-door" barrier of stainless-steel gauze of 24-mesh held horizontally in the mould 31/2 in. down from the top. The construction of this insert is shown in Fig. 1. All inserts were preheated prior to casting to prevent chilling. RESULTS The macrostructures of ingots of the three compositions are described, in terms of the three generally recognized zones, in Table I, and illustrated in Figs. 2(a) to (c). The most interesting observation in this table is that relating to the shape of the equiaxed grains, which were not in fact equiaxed but of almost tear-drop shape. Closer examination of these grains showed that each consisted of a head which had a coarse dendritic structure and a tail which always grew in the opposite direction to heat flow, and which had the same structure as that of the columnar material of the ingot concerned; i.e., in the pure aluminum and 0.1 pct Cu alloy it was cellular and in the 2 pct Cu alloy it was cellular-dendritic. Identification of original cast grains was greatly hampered in the super-purity aluminum ingots, and to a lesser degree in the 0.1 pct Cu alloy,

Jan 1, 1968

By Campbell Hunter

PETROLEUM is found in almost every province in Persia. On the northern frontier, along the southern shore of the Caspian Sea, it is found near Anzelli and Shakhtesar and gas at Khoremabad. Oil is also found at Gumush Tepe, northwest of Astrabad, on the southeastern shore of the Caspian Sea. Further inland, to the south of Astrabad, oil is found at Schahkuh-i-balae, also on the margin of the Khorasan desert at Semnan, 115 mi. (35 m.) east of Teheran. Along the western frontier, from northwest to southeast, oil is encountered at Ouschachi, north of Lake Urumieh; in the province of Azerbaijan, at Zohab, Khanikin, and other places in the district of Kormanshah in the province, of Ardelan. Further south, in the province of Luristan, oil is found east of Mendeli and in the Pusht-i-kuh districts. Considerable quantities of oil are also obtained from Schuster, Maidan-i-Naphtun, Ram-Hormuz, Beheban, which are almost on a straight line, running northwest and southeast along the foothills of the Bakhtiari Mountains. At Ahwaz, in the province of Arabistan, oil has been found along another range of hills whose axis also lies in a northwest-southeast direction. In the Fars province, boring for oil has taken place at Daliki, and indications of oil are found at Kheri, Fasa, Darab, and other places. A gas show is also recorded at Kuhi-Sung-Atush in this province, 30 mi. (48 km.) east of Darab. In the south of Persia, oil is encountered on. Qishm Island, also at Ahmedi and other places north of Bunder Abbas. On the southeastern frontier, oil is found on the Sarhad range of hills. Thus, oil indications have been noted over a distance of approximately 1100 mi. along the western and 700 mi. along the northern frontiers of Persia.

Jan 2, 1920

By J. Elmer Thomas

The evolution of the oil business is one of the great industrial romances of modern times. First used as a medicine, then as a lubricant, then as an illuminant, and finally as a motor fuel, each change in its principal usage caused large increases in consumption. Producing Successes The producing branch of the industry responded ably to the demands made upon it. Never was there a famine, rarely any threat of scarcity, and stored inventories were gradually accumulated to form comfortable working stocks. Originally an erratic and hazardous undertaking, the discovery and development of oil fields has made such strides as to classify now as a science. When storage stocks were low, production in close balance with consumption, and demand trending sharply upward, considerable concern was expressed over future needs. Price was very responsive to fluctuations in supply under those conditions, and quotations for crude and refined oils exhibited wide swings. A very different situation exists today. Consideration of the statistics only since the war will show how recent has been this change. In the 10-year period from 1918 to 1927 inclusive, we produced in the United States 6,100,000,000 bbl. of crude and imported 900,000,000 bbl., our total supply being 7,000,000,000 bbl. The consumption was 6,600,000,000 bbl., thus adding to stocks 400,000,000 bbl., an accumulation of somewhat less than 6 per cent. of the total supply. During that period virtually every field was promptly developed as soon as discovered and nearly every well in the country was producing at full capacity. With the maximum production of the wells required to take care of the rapid increases in consumption, with storage stocks moderate and proven reserves very slight, the producing division of the industry acquired a tempo not needed now. Potential Surplus Today the situation is vastly different. The economic consumption is about 2,700,000 bbl., with current production slightly in excess of that.

Jan 1, 1930

By A. S. Richardson

THE conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Co. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on. The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are : heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 2, 1922

By H. I. Aaronson, H. A. Domian

ELectvon-probe analgsis has been used to in7:estigatr the partition ot alloying- elements between aus-tenite and proeutectoid ferrite (or the Jerritic component of bainite) in high-purity Fe-C-X alloys, lsuully at tzco levels of carbon content fca 0.1 and 0.4 pct in ntost steels) at temperatures between the M, and the Ae3 in Si, mn, Ni, mo, Co, Al, Cr, Cu, and PI steels. No partition ous found during the early stages of transformation at any temperature studied in the Si, ,mo. Co, Al, Cr, and Cu steels. Partition did take place, Jrowel'er, in Ihe Mn, ATi, and Pt steels, occurring in lewtperature. regions below the Ae3 of ca 130°, 65", UNDERSTANDING the mechanisms through which alloying elements influence the kinetics of austenite decomposition reactions which proceed by nucleation and 35c respectively. A break was discovered in the TTT curve for the initiation oj the proeutectoid ferrite reaction in the latter steels at the temperature at which partition began. The alloy content in ferrite at the a:y bondavy remained at constart lecels, shown experimentally to be significantly above those corresponding to eqiilib+iu??l, e'en at the longest reaction times investigated (ca 1o6sec). The partition and the TTT curve observations foere rationalized on the basis of the thermodynamic treatment developed in an accompany ing paper. and diffusional growth has been a major research objective of physical metallurgy since the latter part of the 19th century. The measurements made on the dif-fusivities of carbon and of substitutional alloying elements in austenite during the 1930's and 1940's seemed to provide a useful clue as to the nature of these mechanisms. These measurements showed that the diffu-sivity of carbon is several orders of magnitude higher than that of the alloying elements at a given tempera-

Jan 1, 1967

By Alfred F. Beasley

The slags derived from the smelting of lead and copper ores are composed essentially of silicates. The problems arising from the smelting of these ores consequently involve the study of silicate fusions. In the absence of specific knowledge concerning the compounds occurring in slags, it has been the practice of metallurgists to treat them in terms of their total chemical composition. Slags have been classified as monosilicates, bisilicates, sesquisilicates, and subsilicates according to the relative amounts of oxygen in the acid and basic radicles of the hypothetical salt produced. While this has been a useful guide to metallurgists in computing the furnace charges, it falls far short of a basis for the scientific investigation of slags. In order to understand the nature of a slag as a whole it is necessary to learn the physical and chemical properties of the mineral compounds which go to make up that slag. The efficiency with which an ore is smelted in a furnace depends primarily on the physical properties of the compounds formed during the operation. When the melting points and fields of stability of each of the mineral compounds in slags have been established, it will be possible to determine the properties of any given slag by examining the nature and amounts of its mineral constituents. Earlier Investigations In 1884 and succeeding years an extensive survey of lead and copper furnace slags was made in Europe by Vogt, and a large part of the present knowledge of the subject is due to his publications.' Vogt's interest in artificial fusions was directed primarily towards the explanation of problems in igneous and economic geology and his subsequent works have been confined wholly to that subject.

Jan 1, 1930

By C. R. Fast

In order to evaluate the ability of a Hydrafrac treatment to effect a sustained increase in well production, data were accumulated on the first 65 wells in 26 fields treated by Stano-lind. Since these data were obtained from such a large number of fields, it is felt that individual well or reservoir characteristics do not affect the overall picture, as might be the case if the study were made in one field or one group of wells in a field. These data are tabulated in Table I and plotted on Figs. 1 and 2. An analysis of Fig. 1 shows that at the end of six months, 75 per cent, or 45, of 60 wells on which data were available showed a sustained production increase. At the end of two years, data were available on 25 wells. Of these, 15 wells, or 60 per cent, showed a sustained production increase. At the end of three years, 55 per cent, or 10, of 18 wells had a production rate greater at that time than before Hydrafrac treatment. The lack of information on additional wells at the end of the third year is primarily a result of the small number of treatments conducted in the early stages of field application

Jan 1, 1952

By Gerald F. G. Sherman

The ore deposits of the Warren district, in which the mines of the Copper Queen Consolidated Mining Co. are situated, have been described in a number of technical publications, and will not be discussed here in detail. Certain of their characteristics, however, control methods of underground transportation and hoisting of ore. In the Copper Queen mine, the majority of the ore has occurred in a zone encircling the west boundary of the porphyry intrusion of Sacramento Hill. It has a width varying from 800 to 1,200 ft., and a thickness of about 400 ft. It reaches the surface in the older part of the mine to the northwest, but dips to the southeast, where it is reached at 1,400 ft. below the Czar collar, in its farthest extension at present developed on Copper Queen ground. There is one major extension from the northwest end of the zone toward the west along the Czar fault, and others of minor importance. Individual orebodies are scattercd through the zone in an eccentric manner, only matched by their own irregularities of form and size. Their most gencral characteristics are the softness of the ore and their grcat horizontal rather than vertical extent. It has been estimated that the average vertical thickness of ore in the Czar and Lowell divisions is between 30 and 35 ft. It is calculated by assuming it to be uniformly distributed over its horizontally projected area. In this zone, and for some distance above it, the ground has been subjected to intense alteration and intense but irregular oxidation. It has resulted in an enormous quantity of earthy or clayey material, which may be either ore or waste, which when wet is both heavy and tenacious. Below alteration, the ground is fairly hard, and the limestones contain primary ores differing from those heretofore considered typical of the camp, and which have not yet been thoroughly exploited. The mine production has been drawn from many orebodies spread over a great area.l A diagram map (Fig. I), of haulage drifts and loading stations, illustrates the situation in 1914.

Jan 1, 1916

By K. A. ACKLEY

The petroleum industry experienced a year of satisfactory accomplishment in Oklahoma during 1945. Crude oil production was increased, a new record for recent years was established in well completions, and refinery operations were maintained at a maximum level. Daily average crude oil production increased to 382,000 bbl., reflecting a 13.5 per cent gain compared with production during the previous pear. Total wells drilled during 1945 amounted to 2556, a gain of 28.7 per cent over 1944 Refinery throughout averaged 187,500 bbl. daily, an increase of approximately 4 percent over the preceding year.

Jan 1, 1946

By T. L. Joseph

A study is made of the amount of solution loss necessary to maintain the reducing power of the gas stream in the blast furnace. Curves are presented to show the effect of solution loss, moisture in the blast, and carbon dioxide from the flux on the nitrogen in the THE blast furnace process is based upon the counter flow of gases and solids. As CO, N, and H, flow upward from the combustion zones, oxygen is acquired from the descending charge. In the reduction of iron ore, a portion of CO is converted to CO, and similarly a portion of H, is converted to water vapor. The inert N,, from the air used in combustion, passes through the furnace with little change. Its concentration is, however, decreased by reactions such as direct reduction and solution loss which increase the volume of CO in the gas stream; Similarly the evolution of C02 from the limestone also dilutes the nitrogen. he purpose of this paper is to illustrate an idealized and simplified method of studying furnace processes by following changes in the gas phase between the tuyeres and the stock line. A more specific objective is to evaluate the effect of solution loss upon the CO/CO, ratio in that region of the furnace in which FeO is reduced to metallic iron. This last stage of reduction requires relatively high CO/CO, ratios to exceed the equilibrium requirements. Solution loss or the reaction of COZ with C to produce CO has a pronounced effect upon the ratio of the carbon gases and is necessary to maintain the reducing power of the gas stream if the consumption of coke is low. It will be explained later that indirect reduction followed by solution loss is stoichiometri-cally equivalent to direct reduction. Calculations will be made to show how the composition of the gas in the region of the mantle varies with coke consumption and with different amounts of solution loss. Such calculations show the condi- tions under which gasification of C with oxygen in the charge is needed to maintain the reducing power of the gas. Equilibrium conditions for FeO and the carbon gases will be used to establish a minimum CO/CO, ratio below which reduction will not proceed. The manner in which carbon is gasified in the furnace, at the tuyeres with oxygen in the air or above the tuyeres with oxygen from the charge, will be a basic feature of all calculations. It is hoped that greater interest in the use of top gas as a means of following furnace reactions will be aroused by the calculations and generalized curves which are presented. Bosh Gas Equations Subject to some alteration by the amount of moisture in the blast and by direct reduction, the gas leaving the combustion zones of a blast furnace has a definite composition. Because a relatively small amount of oxygen is acquired from the charge in the bosh and in the crucible, the products of combustion undergo little change until they enter the shaft. Bosh gas is, therefore, essentially the products of combustion of carbon in a deep fuel bed with air. The relative weights and volumes of reacting materials are expressed by the equation: 2~ + 0? + 3.76N, = 2C0 $ 3.76NZ [I] Air Bosh Gas -air = 79% N? = 3.76) 21% 02 Starting with a known mass of C consumed largely by air, Eq 1, but partly by water vapor, Eq 2, the volume and C + H2O = CO $ H? [21 composition of the bosh gas can be calculated and subsequent changes followed as reactions take place at various elevations in the furnace. As shown in

Jan 1, 1952

By William G. Kegel

Apart from a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing ,more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor ; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating

Jan 1, 1981

By W. A. Klikoff, I. Fatt

The concept of fractional wet wattability is examined. Fractional water wettability of a reservoir rock is defined as the fraction of the internal surface urea that is in contact with water. Capillary pressure and relalive permeability of unconsolidated sand are shown to be functions of fractional wettability. INTRODUCTION The petroleum industry has long recognized that wettability of reservoir rock has an important effect on multiphase flow of oil, water and gas through reservoirs. As early as 1928 the American Petroleum Institute sponsored a study of wettability as part of API Project 27 at the U. of Michigan.' Despite 30 years of research, there is still little exact knowledge of the wettability of reservoir rocks. There are two parts to the wettability problem. After agreeing to a uniform nomenclature in regard to wettability,' the first question to be answered is, "What is the in situ wettability of a given reservoir rock?" If this can he answered the next question is, "What part does wettability play in determining the characteristics of multiphase fluid flow through the rock?" This paper represents an oblique attack on the problem of wettability. No attempt is made here to answer the basic question of wettability in situ. instead the consequences of the concept of fractional wettability are examined. Multiphase flow in sandpacks is shown to he highly influenced by fractional wettability. Jennings' has given 3 definition of wettability and the other terms used in discussing wettability. These terms must be applied to the physical situation existing In reservoir rock. A survey of the pertinent literature from 1928 to 1956 indicates that the concept of a contact angle was applied to reservoir rock in the same way it would be applied to a flat, homogeneous surface. Attempts were made to state quantitatively the wettability of a reservoir rock in terms of a contact angle which was presumably constant at all points on the very rough and heterogeneous interior surface of a porous rock. Calhoun, et al,3-6 prepared synthetic consolidated and un-consolidated porous media in which they claimed there was a known uniform contact angle. They then showed the effects on the capillary pressure and relative permeability characteristics of varying this angle. The API Project 47 at the U. of Texas' and others' have made extensive studies of an indirect approach to the contact angle through the use of heat of wetting data. Even if successful. however, this approach also states the wettability of porous rock in terms of a contact angle which is uniform over the entirc surface. If the angle varies from one part to another on the internal surface, there is no way of determining from the measurements the area distribution of contact angles. In 1956 Brown and Fatt5 suggested that the concept of a contact angle, as applied to reservoir rock, be abandoned. This suggestion was made because it is known that the internal surface of most reservoir rocks is composed of many different minerals, cach with a different surface chemistry and a different capacity to adsorh surface active materials from reservoir fluids. Furthermore, the operation of a contact angle in determining the form of a fluid-fluid interface is difficult to picture in the very complex geometry of a pore. Brown and Fatt proposed that the wettability of reservoir rock be stated in terms of the fractional internal surface area that is in contact with water or oil. All surfaces on which there is water are called water-wet; surfaces on which there is oil are called oil-wet. The fractional water wettability is then stated as a number which represents the fraction of the internal surface that is in contact with water. A symmetrical statement can be made for the fractional oil wettability. The concept of a fractional wettability as previously stated has in its favor the recognition of the heterogeneous mineral composition of most reservoir rocks. Another point in its favor is that fractional wettability can be measured quantitatively with relative ease. Hol-brook and Bernard10 se a simple dye adsorption test to obtain fractional wettability of reservoir rocks. Amott11 uses a combination of imbibition and displacement to arrive at a wettability index of reservoir rocks which seems related to fractional wettability in the range 0.25 to 0.75 fractional water wettability. Jennings" has shown the changes in relative permeability that take place when a porous material is changed from unity to zero fractional water wettability. He also shows that reservoir rocks in their natural state, but at room temperature and atmospheric pressure, have relative permeability characteristics which would indi-

The following discussion occurred on the afternoon of Sept,. 22, 1930, as part of the fall meeting of the Iron and Steel Division at Chicago. About seventy-five men attended this session. C. B. Murray opened the meeting, as follows: C. B. Murray, Cleveland, Ohio.—It is very encouraging to see so many here this afternoon to discuss this important matter of beneficiation. The producers of ore, I am sure, are anxious to furnish the grade of ore that the consumer wants. The consumer sometimes wants that which cannot be economically produced and often the producer cannot understand why the consumer wants certain things. It was to bring together these two interested parties that this meeting was proposed. I was appointed the chairman of the meeting, chiefly because I happened to be the chairman of the Iron Ore Committee of the Institute. I know a little about iron ore but have not perhaps kept up with the times in blast-furnace practice. I am asking Mr. Sweetser, who is well informed from both sides, to take over the meeting and carry on the discussion. R. H. Sweetser, Columbus, Ohio.—We want to have a free discussion between the iron-ore men and the blast-furnace men as to just what we are trying to reach in the beneficiation of iron ores. Many of those present have had a great deal of experience. There are men here from the ranges who have been passing through the experimental stage of beneficiation of iron ores, and there are some who have already gone on to commercial production. We have reached the point where the beneficiation of iron ore is important to the whole iron and steel industry. The connection between iron-ore beneficiation and the cleaning of coal is so close that I think we can profit by working very close to the coal people. Some Aspects of the Iron-ore Situation W. G. Swart, Babbitt, Minn.—I was very much interested in Mr. Richards'* paper on tonnages and the 20-year life. There is one interesting thing about the ore reserves; that is, the irregular distribution of that tonnage. On the Mesabi Range, for example, the United States Steel Corpn. owns between 70 and 75 per cent. of the reserve tonnage. They ship bctween 40 and 50 per cent. of the annual Lake Superior

Jan 1, 1930

By A. A. Blow

The productive area of the Leadville mining district immediately adjoining the city of Leadville, which, by its wonderful richness, has attracted the attention of the mining world for the past twelve years, may, with a few exceptions, he considered as divided into seven local mining centers, separated one from another by the topographical features of the country, and designated by common consent as Fryer Hill, Yankee Hill, Breece Hill, Rock Mill, Printer-Boy Hill, Iron Hill, and Carbonate Hill. Of these seven distinot mining localities, or groups of mines, the central one, Iron Hill, is the one of greatest importance and interest. It was the scene of the earliest discovery of carbonates, as far back as 1875, and since that time has always maintained its position

Jan 1, 1890