Search Documents

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

By O. M. TUPPER

REQUIRING a finer ground clay than that obtainable with a dry pan or hammer mill, the Clay Corporation of California installed a five-roller, low- side Raymond impact mill at its Lincoln plant in 1925 and since then has been economically grinding fire clay with a moisture content as high as 15 per cent. This was one of the first, if not the first, of this type of mill to be used in the grinding of clay on the Pacific coast. The pulverizer consists of a die-ring, lying in a horizontal plane, enclosed in a sheet-iron housing. A vertical shaft supports a spider from which five rolls are suspended in such a way as to always have them bearing on the die-ring. The vertical mill shaft is driven by means of beveled gear and pinion from a horizontal shaft which is connected by belt with a 60-hp. motor with suitable pulleys to give a speed of 175 r.p.m. A large fan which has a speed of 1100 r.p.m. and is belt connected to a 40-hp. motor is connected to the mill housing. The discharge end of the fan is in turn connected to a cyclone dust collector.

Jan 1, 1929

By H. H. Reamer, B. H. Sage

The formation volume and the relative volume of the liquid Phase of mixtures of Condensate and gas from five different parts of a field in the Louisiana area have been established experimentally. These studies included gas-condensate ratios as high as 25.000 cu ft/bbl at pressures up to 5,000 psi. The gravities of the tank condensates were between 53.9° and 63.9° API. The compositions of the condensate and gas samples inves-ligated are presented in tabular form. The formation volume. the relative volume of the liquid phase. and the specific volume of the mixtures are available. A rough correlation of the formation volume as a function of pressure. temperature, and gas-condensate ratio has been presented. This correlation i-considered applicable only to the range of conditions covered in this investigation for systems of similar nature and com-position. INTRODUCTION Often a knowledge of the influence of temperature. Pres sure, and relative quantities of condensate and gas upon the volumetric behavior of fluid*. from a given field has been employed in estimating the Conditions existing in the reservoir. The early work of Beecher and Parkhurst' and the more rrcent Studies of the Dominguez' and San Joaqnin Valley Field;: are examples of experimental studies of this character. Correlation of the volumetric behavior of naturally occurring hydrocarbon mixtures has Proved To be feasible' . at low gas-conden-sate ratios-; for fluids*. from a single geographic area. Progres 5 is being made in the Prediction of the volumetric behavior of distillate systems at high gas-condensate ratios and pressure.. However. the estimation of the retrograde". ' dew-point pressure still remains uncertain and probably can best be established by experiment. For this reason it appears of interest to make available experimental information about the volumetric behavior of mixtures of condensate and gas from five different part.; of a single field. This material shows a rough similarity to data for mixtures of condensate and gas from San Joaqnin ' Valley Fields. In the present paper. 110 attempt has been made to coordinate the available information on tbe volumetric behavior of fluids from condensate fields. It appears hopeful that progress can be realized by the utilization of recently developed equa-tions of state.!' However. the primary problem in any such correlation is the proper identification of the components and constituents of naturally occuring systems. Additional experimental information may be required to permit the determination of the values of the constants of the equation of state for References given at end of paper. Manuscriptt received in the office of the Petroleum Branch June 11. 1951. *For present purposes low gas- condensate ratios will he considered as those below 3,000 cu ft/bbl, and the region of high gas-condensate ratio will be limited to compositions containing more than 5,000 cu ft of pas per bbl of condensate. Mixtures Containing between 3,000 and 5.000 CII ft OF gas per bbl will be considered of intermediate gas-condensate ratio.

Jan 1, 1952

By George Krauss, Morris Cohen

NUMEROUS investigators1-4 have shown that one of the most conspicuous effects of the reverse marten-sitic transformation in Fe-Ni alloys is the stabilization of the austenite which forms on reversal. However, the present authors5 found a virtual absence of stabilization in a recent study of this subject. The purpose of this note is to account for the discrepancy.

Jan 1, 1963

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35°F and 135°F. Results are accurate to the seventh decimal place.

Jan 6, 1950

By S. Feuerstein, L. Rice

The effect of low pressures on the flow and fracture behavior of molybdenum is described. For poly crystalline samples, room-temperature tensile tests indicate greater ductility under 10 Torr than under intermediate pressures up to and including atmospheric pressure (760 Torr). In addition, tests conducted at 760 Torr under atmospheres of air, dry nitrogen, and purified argon exhibited no apparent difference in mechanical properties. Critical tests involving baking in situ as well as those involving single-crystal deformation further imply that the ductility effect is a pressure-dependent phenomenon related only to the fracture process. This dependency is discussed in terms of adsorption and diffusion contributions. THE effect of very low pressures on material properties has heretofore been presumed to be important only for substances possessing relatively high vapor pressures at ambient temperatures. Research has therefore been concentrated primarily on organic solids and liquids, and in some instances on metals such as zinc and cadmium. Most vacuum-effect studies' on the mechanical behavior of metals have been performed under conditions of either cyclic loading or creep rupture at elevated temperatures, i.e., over extended time periods. These studies were not restricted to high vapor pressure materials but also encompassed such metals as gold, copper, and nickel. Very little concern, however, was placed upon the importance of a vacuum environment on the mechanical behavior of metals subjected to a simple unidirectional deformation at ambient temperatures. A tension test is generally of short duration as compared to a creep test, and at room temperature vacuum effects if any would be expected to be surface-limited. In early 1963, Kramer and podlaseck2 reported a change in the bulk flow behavior of aluminum single crystals during room-temperature tension tests. The deformations were performed under pressure conditions of 760 to 3.4 X 10-8 Torr and indicated for the first time a vacuum surface effect contributing to the bulk tensile behavior of metal specimens. As a consequence, an experimental program was initiated in this Laboratory to study the effects of ultrahigh-vacuum conditions on the mechanical behavior of metals. The results of a preliminary study on poly-crystalline molybdenum3 revealed, unlike Kramer's observations of changes in the stress-strain behavior, only an increased ductility under ultrahigh vacuum. Flow behaviors were nearly identical for all tests re- gardless of pressure. This paper presents comprehensive results obtained in this area of research. 1) EXPERIMENTAL PROCEDURE Three material categories were used in this study: sintered and are-cast polycrystalline molybdenum of nominal purity 99.93+ pct and single-pass electron-beam zone-refined molybdenum single crystals having a nominal purity level of 99.99+ pct. The interstitial levels (weight percent) as determined by the Materials Testing Laboratories, Division of Magnaflux Corp., were as follows: sintered molybdenum (C— 0.005, H—0.0004, O—0.015, N—0.008); and arc-cast molybdenum (C-0.0038, H-0.0003, O-0.015, N-0.023). Single-crystal molybdenum obtained from Materials Research Corp. had a typical interstitial analysis of C-0.0015, H-0.00007, O—0.00045, and N-0.0001. Tensile specimens having a 5 mm diam by 50.8 mm length were prepared from these materials. An average grain diameter of 0.059 mm was obtained for the sintered specimens following a 4-hr, 1600°C heat treatment. Grain sizes from 0.019 to 0.149 mm were obtained in the arc-cast specimens following heat treatments from 1100° to 1600°C for 1 hr. This series of specimens was used exclusively for the grain-size effect studies. All samples were electrolytically polished in 97 pct sulfuric acid solution prior to testing. Experiments were performed at room temperature in an ion-pumped ultrahigh-vacuum system positioned in an Instron tensile machine, Fig. 1. A constant strain rate of 4.2 x 10-4 sec-1 as derived from crosshead displacement was assumed for the deformations. Starting vacuums ranged from 2 to 0.5 X 10-10 Torr. These pressure measurements were made using corrected values4 of an NRC Redhead gage. Comparative readings were also made against a G.E. triggered dis-

Jan 1, 1967

By R. E. Reed-Hill

A simple accurate graphical method for orienting fcc crystals using (111) slip traces on a single surface is described. Solutions placing the pole of the surface in a unit stereographic triangle are obtained using a Wulffnet, a (111) standard projection showing the four (111) planes, and a (111) standard projection ruled into unit stereogmphic triangles. The multiplicity of solutions is described in relation to this method. AN accurate, rapid single-surface technique for orienting fcc crystals, using (111) slip or twin traces, has been a matter of continuing interest, as evidenced by the periodic appearance of papers on this subject.'-4 This note presents a new method possessing some advantages over those previously reported. It is an analog to the technique for hcp metals5 where the solution is based upon a stereographic rotation of the specimen surface on a (0002) standard projection that contains the planes of the possible features that might account for the observed traces. In the hexagonal solution, the axis of rotation is the basal-plane trace in the surface. In the fcc case, the axis of rotation is one of the observed ( 111) slip or twin traces. It has been observed that the solution is greatly facilitated if the indicated movements of the (111) traces during the rotation of the surface are plotted directly on a paper copy of a Wulff net as shown schematically in Fig. 1. The trace selected to represent the axis of rotation is assumed to fall at the north-south poles of the Wulff net. The directions of the other traces are then plotted as points at the proper angles around one-half of the basic circle of the net. The loci of points corresponding to the movements of these traces (directions) during a 90-deg rotation of the surface, about the polar axis of the net, are then easily and accurately drawn by following the appropriate small circles on the Wulff net. The solutions to the problem are obtained with the aid of a (111) standard projection of the (111) planes, see Fig. 2. This is normally a Xerox copy of a carefully drawn master made on high-quality tracing paper. The (111) standard projection is superimposed over the Wulff net and rotated about its center until the points of intersection of the loci of surface traces, drawn on the Wulff net, and the great circles representing the (111) traces, all lie along a common meridian of the Wulff net as demonstrated in Fig. 3. This latter great circle represents a possible position of the surface. The pole of this plane is then plotted on the (111) standard projection. Its location in a unit stereographic triangle may be readily obtained by superimposing (over the standard projection) another tracing paper (111) standard projection subdivided into unit stereographic triangles. The result of this last operation is shown in Fig. 4. MULTIPLICITY OF THE SOLUTIONS The maximum possible number of (111) traces on a single grain surface is four. Any one may be selected as the axis about which the surface is rotated. Corresponding to each such choice are three possible surface-pole orientations, related to each other by a simple 120-deg rotation about the pole of the (111) basic circle. This is a direct result of the threefold symmetry of the (111) standard projection. Since each of the four rotations will normally give a different set of three-pole positions, there are, accordingly, twelve possible solutions. Each of these twelve solutions places the surface pole in the same relative position in a stereographic triangle so that all are crystallo-graphically equivalent. Accordingly, only a single solution is required to obtain a basic orientation of the crystal. It should be noted, however, that the orientations obtained by reflecting* any of these twelve orien- *The reflected orientations may be obtained by a 90-deg rotation of the opposite sense to that shown in Fig. 1. This rotation places the correspond-ing trace loci in the lower hemisphere of the Wulff net rather than in the upper hemisphere. tations through the surface are also possible orientations that could account for the surface traces. Thus, a given set of four traces always corresponds to a pair of basic orientations related by reflection through the specimen surface. This ambiguity can only be re-

Jan 1, 1967

By D. C. Buffum, L. D. Jaffee

QUANTITATIVE measurements of the temper brittleness of steel are made by comparing the difference between embrittled and unembrittled specimens in the temperature of transition from ductile to brittle fracture. Since hardness affects the transition temperature, a study of the combined effects of hardness and temper brittleness appeared desirable. In this investigation a commercial SAE 3140 steel, which has been reported on previously in temper brittleness studies,* was used. Blanks from this steel were austenitized for 1 hr at 900°C and water quenched. The blanks were then divided into six groups and further heat treated as follows: Group 1—tempered at 675°C for 4 hr and water quenched; Groups 2, 3, 4, and 5—tempered at 675", 650°, 625', and 600 °C respectively for 1 hr and water quenched; and Group 6—tempered at 500°C for y2 hr and water quenched. Each of these groups was divided into two parts; one part was tested without further heat treatment, and the other was embrittled for 48 hr at 500°C and water quenched. Tempering treatments between 500" and 600°C were avoided because of the rapid embrittlement occurring in that range for this steel. The heat-treated blanks were machined into standard V-notched Charpy bars. Each group was tested over a range of temperatures on a 217 ft-lb Charpy machine. The energies necessary to fracture the bars and the percentage fibrous fracture of each bar were recorded. The transition temperatures were obtained from a plot of the percentage fibrous fracture as a function of testing temperature. They were taken as the lowest point on these curves at which the fracture was 100 pct fibrous. The transition temperatures for both embrittled and unembrittled specimens are presented in Fig. 1 as function of the hardness. It will be noticed in this figure that the point for the unembrittled condition at 21 Rockwell C is out of line. These specimens were tempered for 4 hr at 675 °C and this point indicated that under isothermal conditions at this temperature, as is well known, embrittlement may develop fast enough to more than offset the effects of softening. From this data, it was concluded that the difference between transition temperatures for the embrittled and unembrittled conditions at any given hardness, within the range of Rockwell C 24 % to 32lh, is constant. It is also concluded that, within the hardness range studied, the transition temperatures for embrittled and unembrittled specimens rise in a parallel fashion with an increase in hardness. The authors wish to acknowledge the assistance of Frank Carr in this work.

Jan 1, 1952

By Daniel Martin

THE dendritic pattern of steels shown by deep etching is used exten-sively as a guide in the inspection and control of the great majority of steels used in ordnance construction and for many applications in indus-try. The value of macroexamination lies in the fact that it enables a qualified observer to make deductions concerning the general quality of relatively large pieces of metal. Not the least of these general character-istics is the nature and extent of the dendritic segregation in the steel, either in the cast condition or after mechanical or thermal treatments. PREVIOUS WORK Detailed methods for macroetching were outlined by Yatsevitch1 and have been standardized by the American Society for Testing Materials. A comprehensive study of the occurrence, origin, and the chemical and crystalline nature of the dendritic structure was given by Keshian.2 The marked persistence of dendritic segregation in nickel steels is fully recognized and has been discussed by Sauveur and Reed' and by others. Very little, however, has been written on the effect of the various elements on the macrostructure of steels, and the purpose of this report is to submit evidence concerning the influence of chromium, nickel and molybdenum on the macrostructure of some 4 by 4-in. ingots cast and treated under closely controlled conditions.

Jan 1, 1939

By K. Matsuda, H. Tanaka, M. Mamiya, H. Majima

Copper cementation was studied from both thermodynamic and kinetic aspects. The temperature effect of copper cementation, which has been recognized as an anomalous result, and the rate enhancement phenomenon observed after the initial linear step are, in particular, focused in this work. The main results obtained are as follows; 1) Free energy changes of copper cementation reactions, calculated by the use of the "Correspondence Principle" of Criss and Cobble are rather insensitive to temperature. 2) A Flow-cell assembly consisting of a special cupric ion electrode, a calomel electrode and a potentiometer is particularly useful for the continuous measurements of copper cementation rate. 3) Two first-order reaction rate constants for the CU2+- Fe system were successfully determined by the use of the flow-cell assembly. 4) Activation energies determined for the initial rate and the 9 maximum rate of CU2+ - Fe system are both 4.6 kcal/mole. This fact suggests that the mechanisms of the initial reaction and the final reaction are essentially the same and both reactions are rate controlled by the diffusion in a boundary layer. The difference in the rate constants of them may fie explained by the effect of the nature of surface deposits. 5) Qualitative explanation of the rate enhancement phenomenon from the initial rate was successfully made by applying Bockris "Penetration Model."

Jan 1, 1976

By M. R. Meyer, W. T. Walter

A great deal is known, in a qualitative sense, about the performance of CMI EB-36 centrifuges. The manufacturer can give reliable guidance for the proper operation of its centrifuges and can give general estimates of expected product moisture and recovery. Quantitative estimates of the effects of changes in the various operating parameters are more difficult to find. The engineer faced with designing a preparation plant may be without the specific data needed to make decisions. For example, to obtain optimum product moisture when drying 9.5 mm X 595 µm (0.4 in. x 28 mesh) coal the centrifuge manufacturer recommends having no more than 5% -595 µm (-28 mesh) material in the centrifuge feed. They know that more -595 µm (-28 mesh)material in the feed will cause higher product moistures, but they usually cannot quantify the increased moisture or describe the shape of the product moisture versus -595 µm (-28 mesh) in the feed curve. This study was conceived to provide quantitative information on the EB-36 centrifuges, focusing on product moisture, recovery, and size degradation. All of the centrifuges tested were Model EB-36 dryers from Centrifugal and Mechanical Industries Inc. (CMI), with feeds in the nominal 9.5 mm x 595 pm (0.4 in. x 28 mesh) range. These are typical centrifugal dryers in this application, and many were available for testing.

Jan 1, 1984

By Charles F. Manness

In the great increase of product which has been accomplished in the American Bessemer plant, through improvements in machinery and refractories, and by more perfect skills in their manipulation

Jan 1, 1881

By D. W. Fuerstenau, D. A. Sullevan

In the experimental work for this comparison of wet and dry grinding, it was found that the size distributions for wet grinding operations are characterized by a constant value of the distribution modulus, (a; whereas, for dry grinding the distribution modulus decreases slightly with increased size reduction. Wet grindability seems independent of the weight of material in the mill while dry grindability depends on weight. Experimental data and eqmtions for each process are presented for noncleavable isotropic material, for cleavable or material in which there is some form of internal stress, and for energy consumption. The equation ED/EW=BK-? (where ED and Ew are, respectively, energy for wet and dry grinding, k is the size modulus, and B and ? are constants) was found to give the ratio of energy. Dry grinding is generally considered to require more energy than wet grinding. Taggart' states that power consumption in wet grinding ranges from 60 to 90 pct of that required for dry grinding. Bond' states that dry grinding requires one third more power than wet grinding. It is interesting that Rose and Sullivan' note this same difference in power required for wet and dry grinding, but they state that on purely mechanical grounds it is difficult to see any great difference in fundamental principles between wet and dry milling, since dry milling may be regarded as wet milling with a fluid of low viscosity (i.e., air vs water). Yet it must be the viscosity of the fluid that is responsible for the differences between wet and dry grinding. Probably the most comprehensive investigation comparing wet and dry grinding has been that made by Coghill and Devaney. They compared the grind-ability of both chert and dolomite in a 19x36-in. batch ball mill under both wet and dry conditions. In these tests the weight of ore in the mill was varied from 35 to 200 lb and each grinding test was carried out for such period of time that the amount of -200-mesh material in the product was essentially the same for each test with a given material. Cog-hill and DeVaney's data for the grindability of dolomite, which are reproduced in Fig. 1, show that a comparison between wet and dry grinding is com- plex. The comminution of a material by a wet grinding method is characterized by a constant grindability over a wide range of mill loadings. Since grindability is the weight of material comminuted per unit of energy expended, it is equivalent to (w)/ (p)(t), where W is the weight of material being ground, P is the power, and t is the grinding time. In the case of wet grinding, the grindability of dolomite in the Coghill and DeVaney experiments was 0.546 * 0.009 ton per hp-hr when the load of dolomite in the mill ranged from 50 to 200 lb. On the other hand, for dry grinding no such simple relationship was found to exist between power, time, and weight of material in the mill. Dry grinding efficiency appears to depend greatly upon the amount of material within the mill. When the mill contained

Jan 1, 1961

As knowledgeable men in the industry know, a mineral occurrence is found through prospecting but an ore deposit is "made" -made through, first, imaginative and effective exploration; thence through efficient engineering, sales and management. There are two main phases of exploration-reconnaissance and target investigation-each of which can be further divided into two additional stages (see accompanying table). The search for a new ore deposit within a known and geologically mapped mining district involves only the last two stages, whereas the search for a new orebody in a virgin geologic environment involves at least three stages and often the full sequence. Of course, some of the exploration stages may be bypassed depending on available results of previous mineral surveys and/or exploration by individuals, business concerns, and governments.

Jan 10, 1967

By James M. Riddle

INTRODUCTION Block-caving mines are generally large operations. Calculating the quantity and value of mineral present and determining the economic limits to mining are complicated processes requiring much time and effort. If these processes are to be worthwhile, they must be accurate and reliable. Success in planning may increase the economic returns significantly. Since capital investments in block-caving mines are generally quite large, and development may span several years, quicker and more accurate methods of mine layout are very worthwhile to the mining industry. The purpose of this study is to develop an approach to the evaluation and layout of block-caving mines. The study included development of a simple approach to modelling ore reserves and a rapid, dynamic programming solution for optimum ultimate mining limits. TRADITIONAL APPROACHES TO BLOCK-CAVING MINE LAYOUT General discussion of techniques of calculating and valuing ore reserves can be found in the literature, (1-4). Mining limit approaches have been investigated by many and follow five general methods: 1, Moving cone method (5) 2. Graphroriented technique (6,7) 3. Dynamic programming technique (7,8,9) 4. Network flow method (10,11) 5. Pillar method (12) Of these investigations, only two were developed for underground mining applications, those of Sharp (9) and Riddle (11).

Jan 1, 1977

By W. C. Leslie

The textures of cold-rolled and of annealed iron are compared with those of an iron-0.8 pct copper alloy in which the amount of precipitation after cold rolling was controlled. Previously published pole figures -for cold-rolled and for annealed iron are confirmed. The effects of precipztatiotz after cold rolling are to retain the cold-rolled texture after annealing, to inhibit the formation of the usual allnealing texture, and to produce elongated recrys-tallized ferrite grains. It is suggested that the inhibition of new textures by precipitation after cold rolling is a general phenomenon. A great deal of attention has been paid to the development of texture during the secondary or tertiary recrystallization of ferritic alloys, but very little work seems to have been done on the control of texture during primary recrystallization. If such control were attained, it might be possible to simplify the processing of oriented materials or to change the characteristics of current cold-rolled and an-nealed products. From previous experience, it seemed likely that texture could be controlled by recrystallizing a supersaturated solid solution. Green, Liebmann, and Yoshidal found that the formation of preferred orientation in aluminum (40 deg rotation about <111> relative to the deformed matrix) was inhibited when iron was retained in supersaturated solid solution in the strained aluminum. The authors attributed this inhibition to iron atoms in solid solution. There is, however, an alternative explanation. Green et al, took a highly supersaturated solution of iron in strained aluminum and heated it to an unspecified temperature for recrystallization. It is probable that precipitation occurred prior to and during recrystallization, and it is proposed that the inhibiting agent is this precipitate, rather than the iron atoms in solid solution. It is important to note that precipitation before cold work is ineffective; the effective precipitate is that formed after cold working and either before or during recrystallization. The location and distribution of the precipitate are critical. Precipitation in such a manner has been found to have profound effects upon kinetics of recrystallization and the microstruc-ture of the recrystallized alloys.2-4 It would be surprising, indeed, if this were accomplished with no change in texture. Because of the relative simplicity of the system, and because of previous experience,4-7 it was decided to determine the effect of precipitation on texture in an alloy of iron and copper. Bush and Lindsay5 found an unspecified change in texture in cold-rolled and annealed low-carbon rimmed steel sheets when the copper content exceeded 0.1 pct. MATERIALS In earlier work, the rate of recrystallization of a low-carbon steel was greatly decreased by 0.80 pct copper, and, after the proper treatment, the recrystallized ferrite grains were greatly elongated.4 Accordingly, it was decided to investigate the effect of precipitation on texture at this level of copper content. The iron and the iron-copper alloy were made from high-quality electrolytic iron and OFHC copper, vacuum-melted in MgO crucibles, cast, hot-rolled to 0.2 in., then machined to 0.150 in. The compositions are given in Table I. The plates were heated to 925°C and brine quenched, twice. This produced a ferrite grain size of ASTM 0 in the iron and ASTM 1 in the Fe-Cu alloy. Disk specimens were cut from the heat-treated plates, repeatedly polished and etched, then used to determine (110) and (200) pole figures by reflection. Despite the complication of large grain size, these pole figures strongly indicated a random texture. PROCEDURES The copper content in solid solution in ferrite before cold rolling and recrystallization, and hence, the amount that could precipitate during the recrys-tallization anneal, was controlled at three levels by heat treatment. The specimens as quenched from 925° C were presumed to have all the copper, 0.80 pct, in solid solution. Other samples of the quenched alloy were aged 5 hr at 700°C to retain about 0.5 pct Cu in solid solution.6 A third set of quenched specimens was reheated to 700°C, then slowly cooled in steps, to reduce the amount of copper in solid solution to a very low level. All specimens were cold-rolled 90 pct, from 0.150 to 0.015 in. thick. The rolling was done in one direction only, i.e., the strip was not reversed between passes, with a jig on the table of the mill to keep the short specimens at 90 deg to the rolls. The rolls were 5 in. in diameter and speed was 35 ft. per min. Machine oil was used as a lubricant. In a supersaturated alloy, the maximum effect of the copper precipitate on microstructure and on recrystallization can be developed by a treatment at 500°C, after cold rolling and before recrystallization.&apos;

Jan 1, 1962

By K. D. Jacob

ALL types of commercial phosphate rock produced throughout the world contain fluorine in quantities ranging from approximately 0.4 to 1.3 per cent in the Curacao and Christmas Island phosphates to 3.1 to 4.2 per cent in the phosphates of the United States and North Africa1. For a given type of rock, the fluorine content is usually roughly propor-tional to the phosphorus content. SIGNIFICANCE OF FLUORINE IN PHOSPHATE ROCK On the basis of chemical and X-ray diffraction studies, Hendricks and co-workers2 concluded that fluorapatite, Ca10F2(P04)6, is the essential phosphatic constituent of the commercial types of domestic phosphate rock. On the other hand, Bredig and co-workers3 have recently advanced the opinion, also based on X-ray diffraction studies, that the mineral phosphates usually contain carbon dioxide in the apatite lattice, and that the phosphate rocks of. the United States are really fluorcarbonate apatites. However, the domestic types of phosphate rock do not seem to differ greatly from coarsely crystalline fluorapatite in their behavior toward chemical reagents in general, and for the purpose of this paper it will suffice to consider fluorapatite as being the essential phosphatic constituent of these types of rock.

Jan 1, 1936

By H. M. Fisher, R. E. Snow, S. C. Sun

SEVERAL constructive and fundamental studies have been made in the analysis of data obtained from experiments carried on with batch ball and rod mills. The operating characteristics of ball milling in small continuous circuits have also been appraised. It is from these analyses that some of the theories of comminution have been developed. Relatively few studies of continuous rod milling have added significantly to the fundamental concepts, because seldom have they yielded sufficiently consistent results. Perhaps they have been too limited in their scope. Careful control of the variables in batch grinding is simple compared with that encountered in a continuous operation. This factor alone has discouraged many investigators. Occasionally results of systematic changes made in industrial rod mill circuits have been published, but usually the data are sketchy and are restricted because of the unwieldiness of the equipment used. The work, in general, has not been comprehensive; nevertheless it has provided empirical relationships that have bridged the gap between postulate and practice so that by proper manipulation of formulae, a mill designer can anticipate mill size and power requirements.14 Although operating variables of a small continuous mill are not so easy to control as with the batch mill, with present day devices, and with careful experimental work, consistent results can be obtained. Nearly four years ago, in the Process Laboratory, Allis-Chalmers Mfg. Co. began a systematic study of the effects of several variables upon the performance of the pilot rod mill. A mill was built in the laboratory to provide the versatility required for the proposed study. It was constructed in sections so that it could be operated, with a few modifications, as a rod mill 30 in. x 8 ft or 30 in. x 4 ft. The discharge end of the shell was flanged so that either an end peripheral discharge or an overflow discharge could be installed. Thus the performance of at least four types of mills could be studied merely by changing the type of discharge or the length of the mill shell. The grinding experiments were designed so that a study could be made of the way in which the mill speed, feed rate, and pulp density influenced the performance of both overflow and end peripheral discharge rod mills. Four sets of experimental data were collected from the four mill arrangements. The mill in each set of experiments was fed at four rates of feed depending on the length of the mill, at four pulp densities, and at five percentages of critical speed. Electrical and mechanical controls were in- stalled to regulate all these independent variables, and auxiliary devices were used to verify the precision of the controls at each point. The dependent variables used to quantify the experiments were the reduction ratio and the hew surface area produced as calculated from sieve analyses. These were incorporated with the energy factor by the calculation of both the new surface produced per unit of energy and the Bond work index.&apos; Rod wear, as a dependent variable, was not studied because of the short period of operation for each run. Exclusive of repeat runs, each set of experiments yielded 80 products, and the total study at least 320 products, all of which were quantified. With the operating information collected, these data presented a bewildering accumulation. Statistical analysis has been invaluable in unraveling the confusion and in presenting a means of establishing the nature and the magnitude of the significant variables. Data presented in this paper are those from the 30 in. x 4 ft end peripheral discharge rod mill, Fig. 1, when limestone was ground at feed rates of 1000, 2000, 4000, and 5000 lb per hr, at pulp densities of 50, 60, 70, and 80 pct solids, and at mill speeds of 50, 60, 70, 80, and 90 pct of the critical speed. These 80 tests have all been run at least twice, and occasionally a third time, to prove that the data obtained were reproducible. The techniques of operation and the methods of quantification of results are described in the following pages and the results analyzed statistically to show the significant variables. The variables are plotted to show the relationships that exist. A massive dolomitic limestone from Waukesha Lime and Stone Co. was used for feed during these experiments because of its availability and its tex-tural uniformity. This limestone analyzed 28.7 pct CaO, 21.0 pct MgO, 6.0 pct SiO2, 0.4 pct A1²O³, and 0.3 pct Fe²O³ and had a loss on ignition of 44.1 pct. It had a rod mill grindability at 14 mesh of 9.6 grams per revolution from which a work index of 13.9 was calculated. The ball mill grindability at

Jan 1, 1955

By Gene Long

10.4-1. Load Design and Construction. Surface mine haulage roads are used for transporting raw products to the mine site, preparation plant, or loading facilities, and to provide personnel and equipment an access to the pits and mine area. All of the aspects of highway engineering, including minimum slope inclines, properly banked curves, and adequate drainage, must be followed to facilitate construction of safe and efficient haulage roads for fast and economical transportation of the mined product to its destination. By maintaining good haulage roads, both truck and equipment maintenance will be kept to a minimum, resulting in reduced mining costs and subsequently higher profits. [ ] There are several basic considerations in haulage road planning. Most important, one must follow all safety procedures in both design and construction of the roadway. A maximum effort should be made to follow current mining plans when laying out and planning haulage roads (aerial photographs can be extremely useful in planning and routing of roadways). Grades, road widths, and curves must be maintained within limits of present and/or planned haulage equipment specifications, since all these factors can limit speed, and hence production (Table 10.4-1). Grades in most mining operations are adverse (against the loaded haul), which increases haul cost per mile. Operators must balance these increased

Jan 1, 1968

By E. P. Jennings

The abundance and value of the tellurium minerals of Colorado is well known, but, as yet, few analyses have been made of them, and I offer these as a small contribution to the chemistry of these valuable ores. 1. Native Tellurium.—The specimens from which the analyses of this mineral were made are from the " John Jay" Mine, Boulder County, Colorado, where it occurs in quite large masses, though mixed with more or less silica and iron pyrites. It is usually a finegrained, tin-white mineral, but sometimes occurs in distorted, hexagonal prisms in cavities in the quartz. Before the blowpipe it gives the reactions for tellurium, sulphur and iron; by cupellation, it yields a small amount of gold. An analysis of a coarsely crystallized specilnen gave the following results : Specific gravity, 5.10.5. Tellurium,.........68.40 Gold, :.........1.36 Iron pyrites,........24 92 Ferric oxide,.....4.37 Silica and silicates,........11.54 Silver, lead, and mercury,... traces. 100.59 Deducting the pyrites, iron oxide and silica, we have for the con]position of the mineral: Tellurium,..........97.78 Gold,.......... 2.27 100.00 Or, considering the gold to be in combination with tellurium to form sylvanite, we have : Nativc tellurium,........96.50 Sylvanite (An, Te3,),........4.50 100.00

Jan 1, 1879