Search Documents

By C. R. Whitney, G. N. Maniar, D. R. Muzyka

Previous results have shown that Pyromet 860, an Fe-Ni-base heat-resistant alloy, is stable at temperatures as high as 1500°F for aging times as long as 100 hr. This Paper describes the results of long-time creep-rupture testing at 1050" to 1400°F at various stress levels. Times as long as 37,660 hr were employed. The effects of time, temperature, and stress on the precipitates and their morphologies were studied by optical and electron microscopy, X-ray and electron diffraction, and microprobe techniques. phase, containing cobalt, nickel, and molybdenum, was detected after extended exposures from 1200" to 1400°F and careful study was performed to describe the kinetics of its formation in this alloy. µ phase formation apparently has little effect on the elevated-tem-perature properties of Pyromet 860. For times as long as 500 hr at 1300°F and below, with µ phase present, m significant effects on ambient temperature properties were noted. For longer times at 1300°F and after 1400°F exposure, the effects of u phase on ambient temperature tensile strength properties are not clear due to y' effects and grain boundary reactions. Electron-vacancy, N,, numbers were calculated using different methods described in literature and correlated with the present findings. In the selection of alloys for use in gas turbine applications, structural stability ranks as a primary criterion. High-temperature strength and cost are also of major concern. With these factors in mind, Pyromet 860 alloy, an Fe-Ni-base superalloy was designed. This alloy combines the cost advantages of Fe-Ni-base alloys such as A-286, 901, and V-57 with improved strength and structural stability'1,2 and no tendency to form the embrittling cellular 77 phase. A previous study3 reported on the stability of Pyro-met 860 at temperatures from 1375" to 157 5°F and times up to 100 hr. That study showed that the y' precipitates increased in size and separation and decreased in number with an increase in time or aging temperature. No deleterious phases were found to occur. In the present work, samples from four production heats were subjected to long-time creep-rupture testing at 1050" to 1400°F at various stress levels. Various heat treatments were used on the starting samples and tests were run up to 37,660 hr. The effects of time, temperature, and stress on the precipitates and their morphologies were studied by optical and electron microscopy, X-ray and electron diffrac- tion, and microprobe techniques. Electron vacancy numbers, Nv , calculations were made by TRW.4 Experimental results are correlated with the Nv data used to predict occurrence of intermetallic phases such as a phase. EXPERIMENTAL PROCEDURE Mechanical Tests. Material for the present study came from four production size heats of Pyromet 860 alloy, weighing from about 3000 to about 10,000 lb. All of these heats were made by vacuum induction melting plus consumable electrode vacuum remelting. The nominal analysis for this alloy is compared with the actual analysis of the four heats in Table I. Sections of these heats were forged to 9/16-in. round bar,3/4-in. square bar, 3-in. round bar, 4-in. square bar, and a gas turbine blade forging about 16 in, long, about 6 in. wide, and weighing about 20 lb. In general, all forging of this alloy is done from a 2050°F furnace temperature. Longitudinal test blanks were cut from the centers of the smaller bars, from mid-radius positions for the 3- and 4-in. bars, and from the air foil of the gas turbine blade and heat-treated according to the procedures outlined in Table 11. Heat treatment A is the "standard treatment" recommended for this alloy for best all-around strength and ductility. Heat treatment B is a modification of treatment A for improved tensile strength at moderate temperatures. The treatment coded C was designed for treating large sections according to a procedure previously described.' Heat treatment D was developed to yield optimum stress relaxation characteristics at 1050°F for a steam turbine bolting application. After heat treatment, the test blanks were machined either to plain bar creep specimens with a gage diameter of 0.252 in., to combination smooth-notched stress-rupture bars with a plain bar diameter of 0.178 in. and a concentration factor of Kt 3.8' at the notched section, or to notch-only specimens. All specimens conformed to ASTM requirements. Metallography. Most of the creep-rupture tests were continued to failure. A few bars were fractured as smooth or notch tensiles after creep-rupture exposures. After fracturing, ordinary metallographic sections were made primarily in gage areas adjacent to fractures to represent a "high-stress" region and through specimen threads to represent a "low-stress" region. All metallographic sections were made in a longitudinal direction with respect to the test specimen axes. For optical microscopy, the samples were etched in glyceregia (15 ml HC1, 5 ml HNO,, 10 ml glycerol). For XRD analysis, the phases were extracted electrolytically in two media: 20 pct &Po4 in H20 for selective extraction of y' and 10 pct HC1 in methanol for carbides and other phases.

Jan 1, 1970

By Richard D. Snouffer

Prime topics of conversation these days are the new concepts of rail haulage for bulk items such as iron ore, potash and coal. We have heard such ideas as the "integral train" and the "unit train" discussed frequently during the past two years at various AIME meetings, and progress reports have kept up a steady appearance in the technical press and in local newspapers. While no railroad has a complete "unit train" in service at this moment, one has 50 fast-discharge cars under construction and the Pennsylvania Railroad has experimented with radio-controlled motive power distributed at intervals throughout the train. To a great extent, however, the promise for greater efficiency and lower costs held out to industry by these new haulage methods is dependent not on greater speed or larger cars or more dedicated equipment alone but, rather, on the utilization of modern practices in the loading and unloading of rail cars. It is the purpose here to examine these two key steps and the up-to-date procedures and equipment they entail.

Jan 7, 1963

By Ralph E. Esarey, G. F. Fix

The oil and gas industry in Indiana in 1938 showed considerable improvement over the preceding year. Most of the drilling and development during the year, as in the past several years, was in the Indiana portion of the Illinois Basin, but increasing interest was apparent in the old Trenton area, for possibilities of further production in the Trenton formation and the underlying St. Peter sandstone. Interest in all other portions of the state was at a new peak, since many areas have never been prospected. Natural gas production continued to drop during 1938, since new discoveries have not been able to keep pace with the rapid decline in older areas. Oil production increased considerably, chiefly through the discovery of new fields. Older fields contributed about the same quantity of oil during 1938 as during the preceding year. There were 159 wells completed in Indiana during 1938, an increase of 25 over the preceding year. Of these, 48 were oil wells, 41 were gas, and '70 failed to find commercial production. Forty-three, or about 20 per cent, were wildcat. Six of these were productive—three oil wells and three gas wells. Thirty-nine wells on which operations started during the year had riot been completed by Dec. 31. Fourteen others were temporarily abandoned, with the possibility that several will be drilled to completion in the near future. A new oil field (Heusler) was discovered in May 1938, in sees. 1 and 12, T. 7 S., R. 12 W., Posey County. Production was found in the Waltersburg (Upper (Chester) sandstone at a depth of approximately 1775 ft. At the close of the year, Heusler field had nine producing wells and two drilling. The Point township area, Posey County, near the confluence of the Wabash and Ohio Rivers, held promise of good production from the McClosky lime, but offsets to the, discovery well had only shows of oil. The discovery well declined rapidly in production arid was finally plugged. In the Oaktown field, Knox County, a wildcat came in with a good flow of gas, extending the field to the east, and proving considerably more acreage. A new gas area was discovered in Sullivan County, and four good wells were completed. The discovery well was in sec. 35, T. 8 N., R. 10 W., and had an initial

Jan 1, 1939

By Ralph E. Esarey, G. F. Fix

The oil and gas industry in Indiana in 1938 showed considerable improvement over the preceding year. Most of the drilling and development during the year, as in the past several years, was in the Indiana portion of the Illinois Basin, but increasing interest was apparent in the old Trenton area, for possibilities of further production in the Trenton formation and the underlying St. Peter sandstone. Interest in all other portions of the state was at a new peak, since many areas have never been prospected. Natural gas production continued to drop during 1938, since new discoveries have not been able to keep pace with the rapid decline in older areas. Oil production increased considerably, chiefly through the discovery of new fields. Older fields contributed about the same quantity of oil during 1938 as during the preceding year. There were 159 wells completed in Indiana during 1938, an increase of 25 over the preceding year. Of these, 48 were oil wells, 41 were gas, and '70 failed to find commercial production. Forty-three, or about 20 per cent, were wildcat. Six of these were productive—three oil wells and three gas wells. Thirty-nine wells on which operations started during the year had riot been completed by Dec. 31. Fourteen others were temporarily abandoned, with the possibility that several will be drilled to completion in the near future. A new oil field (Heusler) was discovered in May 1938, in sees. 1 and 12, T. 7 S., R. 12 W., Posey County. Production was found in the Waltersburg (Upper (Chester) sandstone at a depth of approximately 1775 ft. At the close of the year, Heusler field had nine producing wells and two drilling. The Point township area, Posey County, near the confluence of the Wabash and Ohio Rivers, held promise of good production from the McClosky lime, but offsets to the, discovery well had only shows of oil. The discovery well declined rapidly in production arid was finally plugged. In the Oaktown field, Knox County, a wildcat came in with a good flow of gas, extending the field to the east, and proving considerably more acreage. A new gas area was discovered in Sullivan County, and four good wells were completed. The discovery well was in sec. 35, T. 8 N., R. 10 W., and had an initial

Jan 1, 1939

By D. J. Varnes

Rocks in mines, quarries, and many outcrops commonly show evidence of being under high stress. Saw cuts and drillholes close in, partly mined coal bursts violently, and pillars crush and rock spalls in mines even at moderate depths. Similarly, strong and massive rocks such as granite and sandstone naturally divide themselves into sheets that lie more or less parallel to their outward topographic form. The sheets may be either convex or concave. Thin plates of bare rock surfaces bow up and buckle. Such effects often cannot be explained by the obvious loads now acting on the rock, that is, by loads resulting from overburden, topographic irregularities, or stress concentration around openings. The stresses exceed those that would result from such loads. Two interpretations of such excess stresses have been made. In one, the stresses are assigned in origin to now active tectonic forces. In the other, they are regarded as leftover and locked in from some previous state at which higher pressures prevailed. These two sources may both operate and they generally cannot be distinguished easily in the field. There are other complicating sources of stress such as temperature gradients and chemical alteration. Nevertheless, some bodies of rock, by exfoliating, show evidence of high internal stress even though they are practically unweathered and so isolated topographically that the presence in them of significant stress due to exterior loads or active tectonic forces seems unlikely (Fig. 1). Moreover, completely isolated rocks are known to change density, shape, or size 1,2 to expand under constant compressive stress;3 and even to disintegrate 4,5 without the intervention of weathering processes. The stresses involved here must be truly residual in the sense long used by metallurgists; that is, residual stresses in a body are those that remain.

Jan 1, 1970

By N. F. Foster

The use of piezoelectric semiconducting materials for the fahrication of ultrasonic transducers has raised the upper fundamental frequency limit for transducers from about 200 mc to above 10 kmc, Several types of semiconductor transducer configurations have been proposed and examined experimentally. Depletion-layer transducers have been made and operated at frequencies below 1 kmc hut they appear to he better suited for operation at considerably higher frequencies around 10 knzc. Diffusion-layer transducers have been made and operated in the range 50 to 1000 mc and have exhihited considerably improved conversion losses and bandwidths compared with other transducers available in the frequency range. A variety of novel structures are possible using these new types of transducers, some of which could lead to substantial advances both in research and in the fabrication of ultrasonic delay lines and memory elements. THE field of ultrasonics today spans some five decades of the frequency spectrum from the audible to the kmc range and finds applications ranging from fundamental research into the atomic structure of matter to the degreasing of machine parts. To cover this wide range it has been necessary to develop a great many types of ultrasonic trandsucers utilizing a variety of materials and physical phenomena. The first ultrasonic transducers were made during World War I for a submarine-detection system. They consisted of plates of single-crystal quartz bonded between metal plates and were one of the first applications of the phenomenon of piezoelectricity discovered nearly 30 years previously. Despite the many advances which have been made in transducer technology, piezoelectric transducers using single-crystal quartz are still used almost exclusively for application above about 30 mc. Transducers at these frequencies are normally made in the form of thin quartz plates which are then bonded onto the medium in which the ultrasonic wave is to be propagated. The crystallographic orientation and geometry of these plates determines the type of wave generated and the way in which the efficiency of the electromechanical conversion varies with frequency. Analysis of the design parameters shows1 that the frequency of maximum efficiency (the fundamental or resonant frequency) is that frequency at which the transducer is approximately half the wavelength of the ultrasonic wave in the material. As the frequency increases, the ultrasonic wavelength, and therefore the optimum transducer thickness, decreases and in practice the fabrication of quartz transducers with fundamental freauencies above 100 mc becomes extremely difficult due to the extreme thinness required. For frequencies above 100 mc quartz transducers can be used in overtone-mode operation, and for very high frequencies (500 to 24,000 me) a technique using a quartz rod inserted in a high-Q microwave cavity4 is available. These techniques, however, exhibit comparatively low fractional bandwidths and rather poor conversion efficiencies. The present trend in ultrasonics is towards high frequencies and greater bandwidth to allow the use of shorter pulses which can give increased discrimination in radar-system delay lines and greater storage capacity in computer applications. The increasing demand for more efficient transducers with greater bandwidth

Jan 1, 1964

By K. L. Young

The general energy equation, including change in kinetic energy, was solved by numerical integration and used to evaluate simplifying assumptions and application practices over a wide range of conditions. When extreme conditions were encountered, sizable errors were caused by large integration intervals, application of Simpson's rule and neglecting change in kinetic energy. A maximum error of only 1.31 percent was caused by assuming temperature and compressibility constants at their average value. It was discovered that a discontinuity can develop in the integral for the injection case. This discontinuity indicates a point of zero pressure change and is an inflection point in the pressure traverse. INTRODUCTION When a pressure in a gas well is to be calculated, one of the first decisions is to select a method of calculation. In many instances, this selection becomes a problem because the literature, at best, provides an evaluation of any method for only a limited range of conditions. Once a method has been selected, a question often arises as to the size of the calculation interval which should be used. The question regarding calculation interval arises because an analytic solution is not obtainable and approximate solutions must be used. This paper presents an evaluation of major assumptions and application practices of probably the two most widely used methods for calculating steady-state single-phase gas well pressures. The two methods are Cullender and Smith1-" (numerical integration), and average temperature and com-pressibility. The Cullender-Smith method assumes that change in kinetic energy is negligible and is normally applied in two steps with a Simpson's rule correcton. The average temperature and compressibility method, in addition to neglecting kinetic energy change, asumes that temperature and compressibility are constant at their average values. This method is normally applied for wellhead shut-in pressures of less than 2,000 psi, and in one step. Computer programs were written to compute bottom-hole pressure with and without the assumptions, using various approaches. Values of input parameters investigated are shown in Table 1. Flow rate was limited to a maximum of 5,000 and 10,000 Mcf/D for tubing sizes of 1.610 and 1.995 in. ID, respectively. Flow rate was also limited to 10,000 Mcf/D for a tubing size of 2.441 in. ID when wellhead flowing pressure was 100 psia. These limitations were imposed on flow rate so as not to exceed sonic velocity. The z factor routine available necessitated limiting bottom-hole temperature to 240F and wellhead pressure to 3,000 psia. Pressures were compared on the basis of percent deviation from the trapezoidal integration of Eq. l or 2 at 100-ft intervals. A preliminary investigation indicated that a 1,000-ft interval solution would differ from a 50-ft interval solution by less than 0.25 percent; therefore, the 100-ft interval was chosen for a base. For the purpose of comparison, deviations less than 1 percent were considered insignificant. where 111.1 qeC2/d p = kinetic energy term. Eqs. 1 and 2 can be evaluated numerically at specific depths using the trapezoidal rule as shown by Cullender and Smith. If change in kinetic energy is neglected and temperature and compressibility are assumed constant at their average values, Eq. 1 can be integrated to give the average temperature and compressibility equation,

By John C. F. Randolph

(Read at the Amenia Meeting, October, 1877.) Tits establishment being now in full working order, it has seemed of considerable professional interest to collect together, in a concise form, the various points as to its plan, method of dressing, and equipment. The data contained in this paper have been largely drawn from the able paper of E. Kutscher, constructing engineer. of the works, contained in the Zeitschrift fur Berg-Hütten-und Salinenuesen im Preussischen Staate, 1873, supplemented by some personal memoranda made while the works were under construction and by memoranda on the works appearing in various German technical papers from their completion up to date. This is probably the largest dressing works in the world devoted to the beneficiation of argentiferous lead ores, and it is doubtful if any establishment for the concentration of mineral of any description can compare with it in size. As showing the final practice adopted in an old and very conservative mining region, in which the concentration of ores has been a matter of constant practice and experiment for a very long period, these works are of peculiar interest. The fact that the Clausthal ores strongly resemble a very large and abundant class of ores found in the United States has always attracted the attention of American mining engineers and mine owners to the methods employed in dressing and smelting them. The study of their methods of concentration of ores has, however, always been full of difficulty,

Jan 1, 1878

By Anal J. Mehta, Theodore D. Tiemann

Growing demand for steel and increasing dependence upon foreign ore makes the need for developing the technology for treatment of low-grade iron ores greater than ever before• Representative of these added interests were the studies carried on at the University of Wisconsin• These studies included among others: anionic and cationic flotation, magnetic separation, roasting followed by magnetic separation, electrostatic separation, a hydrogen reduction process,6,7 and caustic digestion• The idea of removing silica by caustic extraction is not new•-1; The principle of concentrating siliceous iron ores by this method is based on the fact that silica is soluble in sodium hydroxide solution while iron oxides are essentially insoluble• For this process to be economically feasible, it is believed that some method of recovering silica from solution as a marketable by-product, with recycling of spent liquor is necessary. Precipitation of silica with carbon dioxide will allow subsequent causticizing of the spent liquor with lime• Caustic thus produced can be recycled for digestion• A flowsheet of the envisioned process is given in [Fig• 1] The purpose of this paper is to describe results obtained from the investigation of carbon dioxide precipitation of silica from sodium silicate solutions, which could be later applied to the caustic extraction process to treat low grade siliceous iron ores, particularly taconites.15 Theoretical Considerations The soluble silicates of sodium include sodium orthosilicate (2Na2O•SiO2), sodium metasilicate (Na20•SiO2), sodium disilicate (Na1O•2SiO2), and more highly siliceous products approaching Na2O•4SiO2• These materials have been described in detail by Vail•16 Stones has reported that the extraction of silica is not significantly affected by the amount of silica in solution until the Si02/Na20 ratio exceeds that of orthosilicate (Ratio = 1/2)• However, as the Si02/Na2O ratio exceeds that of metasilicate (Ratio = 1), silica extraction is significantly impaired• The present experimental work was confined to orthosilicate and metasilicate solutions, as to be successful the envisioned commercial process for the extraction of silica from siliceous iron ores would operate in this region. The mechanism of extraction of silica from aqueous sodium silicate solutions is complex in nature. For the carbon dioxide process-18 of core and mold making in which silica is also precipitated from sodium silicate solutions by gassing with carbon dioxide, the reaction of aqueous silicates with gaseous carbon dioxide has been represented by the equations: [ ] However, these equations are very much oversimplified• It has been shown that the reaction between aqueous sodium silicates and carbon dioxide gas is ionic in nature 18 Considering this fact and the mechanism for digestion of silica in aqueous sodium hydroxide, the overall conversion of aqueous sodium silicates to solid silica may be represented in ionic form by the following equations: [ ] Silicon in the silicate ion is shown here with a coordination number of 6• This may be in doubt, but it is known that ion (SiF°)-2 exists; it seems logical that the Si (OH) e 2 ion should be equally capable of existence•

Jan 1, 1977

By Cyril Wells, Robert F. Mehl

The two earlier papers in this series1,2 presented data on the rate of diffusion of carbon and of manganese in gamma iron. Apart from their scientific interest, these data are needed chiefly in order to treat data on carburization, on rate of formation of pearlite, and on rate of austenit-izing in a quantitative way.1'2'9'10 In the present investigation rates of diffusion of nickel in ?-Fe over wide temperature and concentration ranges have been determined, and the effects of carbon, of im- purities, and of grain size on these rates have been studied. Claussen,3 using the data of Fry,4 has calculated the diffusion coefficient of nickel in y-Fe as 9.2 X 10-11 sq. cm. per sec. at 1200ºC., but had no data from which to calculate the variation of D with concentration, temperature, and percentage of carbon. Method and Materials Method.—Nickel was diffused along the axis of a cylindrical specimen across a concentration gradient, concentration-penetration curves were determined and D values calculated from Grube or Matano solutions.5 Details of the method are given

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The two earlier papers in this series1,2 presented data on the rate of diffusion of carbon and of manganese in gamma iron. Apart from their scientific interest, these data are needed chiefly in order to treat data on carburization, on rate of formation of pearlite, and on rate of austenit-izing in a quantitative way.1'2'9'10 In the present investigation rates of diffusion of nickel in ?-Fe over wide temperature and concentration ranges have been determined, and the effects of carbon, of im- purities, and of grain size on these rates have been studied. Claussen,3 using the data of Fry,4 has calculated the diffusion coefficient of nickel in y-Fe as 9.2 X 10-11 sq. cm. per sec. at 1200ºC., but had no data from which to calculate the variation of D with concentration, temperature, and percentage of carbon. Method and Materials Method.—Nickel was diffused along the axis of a cylindrical specimen across a concentration gradient, concentration-penetration curves were determined and D values calculated from Grube or Matano solutions.5 Details of the method are given

Jan 1, 1941

By S. N. Sharma, William Davis

Because of diminishing energy resources and rising energy costs, every industry is forced to carefully examine its pattern of energy consumption. The copper industry is no exception; current smelting practice begs for technological innovations that would improve the efficiency of its energy utilization. The thermochemical simplicity of copper metal production, as shown in Fig. 1, is deceptive. Designed from the same basic principles, there are four major commercial processes either in use or under construction; and others, such as the Mitsubishi process, are being developed.

Jan 5, 1977

By P. Rama Rao, D. H. Sastry, T. R. Anantharaman

Deformation (a) and twin (a') stacking-fault densities in cold - wor ked filings of fcc silver alloys containing 2, 4, and 6 wt pct Sb have been estimated from Debye-Scherrer peak shifts and asymmetries, respectively. Evidence has been obtained for a possible strain-induced transformation in a two-phase alloy containing 9.0 zut pct Sb. Using Fourier analysis of X-ray line profiles, the effective particle sizes and root mean square strains have been determined for the three fcc alloys in the cold-worked condition. The values of the compound fault probability 0.5a + a') evaluated from peak shifts and asymmetries are in reasonable apeement with those derived from peak broadening. COLD work of fcc metals may produce both deformation and twin (also called growth) stacking faults, which can be detected and quantitatively estimated by X-ray diffraction techniques.' In addition to peak broadening, deformation faults produce a shift in peak positions and twin faults an asymmetry of the Debye-Scherrer reflections. Besides stacking faults, a reduction in the size of coherently diffracting domains and distortion within these also broaden the powder reflections of deformed fcc metals and alloys. Fourier analysis' of peak shapes provides quantitative infor- mation about the effective domain sizes, lattice strains, and also the compound fault probability (1.5a + a'), where a and a' represent deformation-and growth-fault density, respectively. The Paterson method2 for determination of a from peak shifts, the warren3 or wagner4 method for evaluation of a' from peak asymmetries, and the Fourier analysis for quantitative estimates of all the contributory causes of peak broadening have, in the course of the last decade, been extensively applied to obtain data for a number of deformed fcc metals and alloys. One of the useful results of earlier measurements of a in several solid solutions is a correlation between a and the solute valence as well as electron concentration per atom (p) in alloy systems based on a particular solvent. The work of Smallman and westmacott5 on Cu-Zn, Cu-A1, and Cu-Sn, of Foley, Cahn, and ~aynor' on Cu-Si and Cu-Ge, and of Rama Rao and Anantharaman7 on Cu-Si and Cu-Sb has revealed a common trend in the increase of a with p and also a with valency of the solute. Cahn and Davies' and Ad-ler and wagnerg have observed similar trends for silver alloys containing cadmium, indium, and tin. Data on a for silver alloys with a pentavalent solute element are not, however, available. It is primarily to fill this need that the present investigation on Ag-Sb alloys was undertaken. Utilizing the Patersonand Warren methods, values of a and a', respectively, have been determined in three silver alloys containing 2, 4, and 6 wt pct Sb. By Fourier analysis of the broadening of Debye-Scherrer peaks, effective particle sizes, lattice strains, and the compound fault probability (1.5a +a') have also been evaluated.

Jan 1, 1967

By M. E. Nicholson

IT has been suggested by a number of investigators, I including Hume-Rothery and Raynor,' that certain intermediate phases in metal systems take on interstitial crystal structures because of an appropriate ratio of radii of the two atoms. If the size factor is an important parameter in determining whether or not an intermediate phase will have an interstitial structure, then it would appear reasonable that the relative sizes of interstitial atoms should have a direct relation to their solubilities in interstitial compounds. It was on such a basis that Petch,' in his discussion of the cementite structure, concluded that nitrogen is the only possible element which could replace carbon. Recent X-ray studies by Jacka indicate that the solid solubility of nitrogen in cementite is negligible. If this is the case, then on the basis of size factor it would not be expected that any element can replace carbon in FeaC, since according to Schwarzkopf and Kieffer4 the covalent atomic radii of nitrogen, carbon, and boron are 0.71, 0.76, and 0.87A, respectively. Nevertheless, Vogel and Tammann in 1922 indicated that a quasi-binary relation exists between the interstitial compounds FeaC and Fe2B and that the solid solubility of boron in FeaC at approximately 1150°C is 1.4 pct B by weight. Because of the apparent disagreement between theory and experiment, the solid solubility of boron in FeaC has been reinvestigated. In addition, the influence of boron on the saturation magnetic moment (per gram) and Curie temperature of cementite was determined. Experimental Procedure A series of Fe-B-C alloys which varied in boron content from 0 to 5.4 wt pct B were prepared by arc melting a 50-g ingot using carbonyl iron, Ache-son AUC graphite, and Cooper grade A boron for starting materials. The composition of these alloys is listed in Table I and shown graphically in Fig. 1. The samples represented by the solid circles were used for X-ray analysis and Curie temperature measurements; by the squares, samples used for quantitative metallography; and by the triangles, samples used for saturation magnetic moment measurements and Curie temperature measurements. After arc melting and subsequent quenching from 1000°C, so that all phases in the resulting microstructure were brittle, one half of the 50-g ingots were pulverized until a powder was obtained which was less than 100 mesh. These powders were then homogenized in evacuated Vycor capsules at 1000°C for 24 hr and water quenched. Although the homogenized powder had sintered somewhat, it was suitable for saturation magnetic moment and Curie temperature determinations, for which the 60 to 100-mesh fraction of the powder was used. For X-ray analysis the homogenized powder was crushed again until a 300-mesh powder was obtained. After crushing, the powder was mixed with Alundum of approximately the same grit size to prevent sinter-

Jan 1, 1958

By John M. Sharp

John M. Sharp, Jr. (Assistant Professor of Geology, University of Missouri, Columbia, Mo.)-Geothermal gradient and surface temperature data anomalies are potentially useful tools in mineral exploration, These data, however, may reflect a number of geologic and hydrologic processes as well as the thermophysical properties of the geologic materials. The author presents a relatively simple model which may be of value in mineral exploration. The lack of consideration of other processes, however, limits its usefulness. For instance, because of erosion or sediment deposition over geologic time the land surface must be considered a moving boundary in such a model. Evaluation of this effect coupled with annual surface temperature and thermal conductivity variations can result in temperature profiles such as shown in [Figs. 4 to 7]. These effects and others, such as ground-water movement," must be considered and filtered from the data before proper interpretation is possible. Another assumption which should have been discussed is, why were the observed mean surface temperatures not used for extrapolation of the gradients in [Figs. 4, 6, and 7?] Conductive heat transport responds to the actual boundary (land surface) temperature, not to theoretical temperatures in the absence of perturbations. Benfield presents a theoretical model for calculating perturbations in the geothermal gradient for erosion and sedimentation. The temperature (T) at any time (t) and any depth below the surface (x) is given by [ ] where T is the mean surface temperature, G, the geothermal gradient, v, the rate of erosion (or sedimentation),[ ], the long-term rate of change of T0, and k is the thermal diffusivity of the rock. Using the author's values and a rate of erosion of 1.54 cm per yr for a period of 10,000 yr, a thermal profile as shown in [Fig. 10] will be generated. A thermal diffusivity of 0.0164 sq cm per sec was used, corresponding to a thermal conductivity of 0.0082 cal per cm per sec per C. In [Fig. 11], a sediment deposition rate of 3.0 cm per yr for a period of 1000 yr was used to generate the subsurface temperature profile. A surface temperature of 24.3°C was used, as specified in [Fig. 9, 7], was set equal to zero for both cases. Superposition on the generated profiles in [Figs. 10 and 11] of the annual surface temperature variation perturbation (which may be calculated in a number of ways) will yield profiles similar to those in [Figs. 4 and 7]. Similar profiles can also be produced by regional ground-water flow. Models like the author's can be of value in mineral exploration. Other processes, however, which affect surface temperatures and gradients must first be considered, calculated, and filtered from the data if anything but the crudest qualitative interpretation is to be made. Robert C. Edmiston (Author's reply)-Professor Sharp has raised three objections to my interpretation of the subsurface temperature data I collected at Silver Bell. These are: 1) No correction was made for erosion or sedimentation,

Jan 1, 1977

By P. M. Robinson, M. B. Beaer

The heat of formation at 0°C of the intermetallic compound AgMg as a function of composition has been determined by tin-solution calorimetry. In this technique, the heat of formation is determined as the difference in the heat effects, at infinite dilution, on dissolution of the compound and a mixture of its components added alternately to liquid tin from a reference temperature, such as 0°C. The experimental technique and method of calculation have been described elsewhere.' The compound AgMg is a 0 electron compound with a CsCl structure.2 In nonstoichiometric compositions of the compound, atoms of the excess component are substituted on the AgMg lattice.3,4 The homogeneity range is approximately 43 to 52 at. pct Mg at room temperature and 38 to 65 at. pct Mg at 500Oc.2 Single-phase alloys outside the homogeneity range at room temperature can be prepared by quenching. The specimens used in this investigation contained from 39.0 to 54.8 at. pct Mg. They were made available, together with analyses, by the Research Laboratory of the General Electric Co. Metallographic examination of the quenched specimens containing 39.0 and 54.8 at. pct Mg gave no indication of the presence of a precipitated phase. The measured heats of formation are listed in Table I. In a calorimetric run, four to six additions each of a specimen and the corresponding mixture of the components were made. One or two calorimetric runs were carried out with each composition depending on the amount of samples available. The limits stated in the table represent the experimental precision and not the absolute accuracy of the measurements. Thermodynamic investigations of the compound AgMg have been made by Trzebiatowski and Terpilowski 5 and Kachi.6,7 The heats of formation at 500°C derived from the combined electromotive-force values of these investigators8 are more exothermic than the heats of formation at 0°C reported here, Fig. 1. The differences cannot be explained by the difference in temperature. This is shown by the published heat capacity of the stoichiometric compound, which obeys the Kopp-Neumann rule from 0" to 500oC.9 The heats of formation derived from equilibrium data are generally considered to be less accurate than those determined by calorimetric methods because small errors in the change of the equilibrium values with temperature have a large effect on the calculated value of the heat of formation. The heats of formation derived from the combined published electromotive-force values reach a maximum at 56.0 at. pct Mg.8 Kachi reports a maximum of -4.7 kcal per g-atom at the stoichiometric composition.7 The present results also indicate a maximum at or near the stoichio metric composition, Fig. 1.

Jan 1, 1964

By H. F. JR. Miller

(Butte Meeting, August, 1913.) THE major cause of the deterioration of the open-hearth furnace as its length of service increases, is the melting down, or rather the slagging, of the checker-brick, together with the deposition of dirt in the form of iron oxide, etc., which helps to close the openings, as well as to slag the brick by chemical action. Any construction that will do away with the necessity of having the waste gases come down through the checkers will eliminate the main reason for their deterioration. There are some other well-defined reasons which are subordinate to the main one given above. Some of the defects of the present type of regenerator chambers are as follows: 1. The checkers cannot be cleaned while the furnace is in operation, nor can they be cleaned at the end of the run without taking out all of the checker-brick. This causes high costs for labor and brick. The labor cost is high because all checker-brick have to be handled twice. The brick cost is high because many of the bricks are spalled in the double handling, rendering them useless because a spalled brick will not stand up. 2. The top courses of brick become coated with iron oxide, etc., melt clown, and large amounts of dirt are deposited throughout the checkers, especially at the bottom. The draft of the furnace is decreased by the closing of the top and bottom openings, especially the top ones, and the entire working of the furnace is affected. If an effort is made to clean the checkers the dirt and brick falling down into the holes still further diminish the draft. 3. The distribution of the air or waste gases through the checkers is in many cases uneven, resulting in a lower temperature of pre-heated air and therefore a slower working furnace. Also, the passage of air and waste gases is so crooked that sometimes the chimney is not powerful enough to overcome the friction.

Jan 6, 1913

By Frank M. Stephens, Robert D. Macdonald

As processes for handling low-grade or complex ores become more complicated and as new methods are found, the need arises for more complete and detailed pilot-plant studies to protect the capital investment required for a full-scale plant. Occasionally a process is firm technically, but there is a need for a demonstration plant that will convince nontechnical men of the wisdom of investing in a full-scale operation.

Jan 5, 1959

Edwin H. MessiteR, New Pork City (communication to the Secretary*):—Under the heading " Flues," Mr. Edwards refers to the Bee-hive construction, a cross-section of which is shown in Fig. 4 of his paper. A flue similar to this was designed by me about six years ago,' in which the walls though much thinner than those described by Mr. Edwards gave entire satisfaction. These walls, from 2.25 in. thick throughout in the smaller flues, to 3.25 in. in the larger, were built by plastering the cement mortar on expanded-metal lath without the use of any forms, or cribs, whatever, at a cost of labor generally less then $1 per sq. yd. of wall. Of course, where plasterers cannot be obtained on reasonable terms, the cement can be molded between wooden forms, though it is difficult to see how it can be done with an interior core only as stated by Mr. Edwards. In regard to the effect of sulphur dioxide and furnace-gases on the cement, I have found that, in certain cases, this is a matter which must be given very careful attention. Where there is sufficient heat to prevent the existence of condensed moisture inside of the flue, there is apparently no action whatever on the cement, but if the concrete is wet, it is rapidly affected by these gases. At points near the furnaces there is generally sufficient heat not only to prevent internal condensation of the aqueous vapor always present in the gases, but also to evaporate water from rain or snow falling on the outside of the flue. Further along, a point is reached where rain-water will percolate through minute cracks caused by expansion and contraction, and reach the interior, even though internal condensation does not occur there in dry weather. From this point to the end of the flue the roof must be coated on the outside with asphalt paint or other impervious material. In very long flues a point may be reached where moisture will condense on the inside of the malls in cold weather. From this point to

Jan 1, 1905

By V. Steve Reed, Ed L. Reed

The in situ leach mining process generates a waste stream that is high in sulfates, total dissolved solids, and radium 226. During the mining phase, the volume of the waste stream is relatively low and consists primarily of the bleed stream. During the restoration phase, larger volumes of waste water are generated. These waste streams require environrnentally sound disposal. The low net evaporation rate in the Coastal Bend area precludes pond evaporation as a feasible disposal alternative. Reverse osmosis is a practical method of reducing the volume of the waste water handled, but the concentrated waste stream from the reverse osmosis unit must be disposed properly. Deep well injection into highly saline reservoirs is considered a sound method of disposing of the liquid waste generated by in situ mining in the Gulf Coast uranium district. Thirteen injection wells have been permitted to serve the disposal needs of the leach mining industry in Texas. Of these 13, 11 have actually been drilled. Seven applications are pending. The injection zones for the permitted wells range from depths of 3050 to 6200 feet. Pressure limitations imposed on these wells range from 500 psi to 1350 psi. The following criteria are used to determine the desirability of a disposal well site: 1. A minimal number of nearby, improperly plugged borings which penetrate the disposal zone; 2. Minimal crustal disturbance; 3. Sufficient salinity of the water contained in the disposal zone; 4. Protection of oil and gas producing zones; and 5. Sand of sufficient permeability and areal extent to handle the desired volume without fracturing the reservoir. 1. Improperly plugged borings: During the early part of the century, oil wells, gas wells and test holes were drilled using cable tool equipment, often with a minimum amount of surface casing. Production casing, when it was set, was often partly removed when the holes were abandoned. Thus, wells drilled prior to 1940 frequently have less than 100 feet of surface casing and either no production casing or the upper part of the production casing removed. Additionally, these holes are often plugged only with mud. The close proximity of these holes to an injection well location are a concern in that they can provide an avenue for injection-depth fluids to migrate up the bore hole and jeopardize shallower fresh water reservoirs. Usually, where there are more than 6 or 8 poorly plugged borings in a 2 1/2 mile radius of the well site, it is preferable to examine deeper zones for disposal well potential. The deeper zones are especially attractive where the borings are not in a cluster, which renders monitoring more difficult. Often, even the deeper disposal zones are penetrated by a few improperly plugged borings. When this condition arises, the potential for leakage through the borings can be addressed in the following ways. a. Demonstration that the static head in the boring is higher than the anticipated increase in bottom hole pressure generated at the boring by the disposal well. A 100 psi differential between these two pressures is recommended. The calculated increased pressure at a boring caused by injection should be refined using annual bottom hole pressure measurements in the disposal well. Figure 1 illustrates an injection pressure map which can be overlain on the oil well map to determine the anticipated increase in pressure expected at each oil, gas or abandoned hole. b. Shallow ground water monitoring. A shallow monitor well is drilled next to the boring and both pressure and quality measurements are made periodically in the shallow well. c. Disposal zone monitoring. Recently there has been a tendency for regulators to require disposal depth monitor wells instead of shallow well monitoring. We consider disposal depth monitoring to be a less effective method of monitoring because it provides only indirect evidence of potential problems. Assumptions have to be made for the unplugged borings, such as mud weight, that are not addressed by the disposal zone monitoring program. There is little improvement with this system to that discussed in "a" above. A shallow zone monitoring program, however, yields direct evidence of a developing problem with an unplugged boring. Leakage by the boring will be detected quickly by an abnormal increase in pressure in the shallow well. Quality monitoring will detect upward migration of poor quality fluids. The pressure data provide an early warning of impending leakage; the quality monitoring will detect actual fluid migration.

Jan 1, 1980