Search Documents

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By L. Michael Kaas

The mineral industries are striving to expand their use of the computer's ability to process exploration, geologic, and mining data. Digital plotting programs and devices are continuing to gain wider use for lowering the cost and the time required to produce many types of maps and cross-sections commonly used by mining companies. Mineral engineers and geologists will soon be using a new tool, computer graphics, to greatly facilitate the use of computers to solve a large number of industry problems. By means of cathode-ray-tube (CRT) displays, an engineer can search large files of geologic data; display elevation contours, geologic structures, and ore grades; construct geologic and mining cross-sections; and compute tonnages for mining plans or ore reserve estimates. Examples of both digital plotting and cathode-ray-tube problem solving approaches are discussed in this paper.

Jan 1, 1969

Jan 1, 1965

Jan 1, 1944

Jan 1, 1950

Jan 1, 1904

By Claude P. Heiner

mountain region to M tht Coast points for domestic consumption and for export are shown in Table 11. There is considerable disparity in rates from both Rock Springs, Wyo., and Castle Gate, Utah, to the four coast cities where the slack coal is to be used for purposes other than export. The rate on coal to be exported is the same from either starting point to any of the four coast cities even though there is a difference of as much as 341 miles in the shipping distance. It is interesting to note that the freight rate between Sunnyside, Utah, and Fontana, Calif., on coking coal is $5.05 per ton and that coal up to 8 in. can be moved on this rate if it is suitable for coking. This rate was published late in 1942 on a contemplated annual movement of more than 500,000 tons. There have been decreases in freight rates since 1923 on movements of slack coal from Utah into Seattle and Portland due to pressure on the railroads and to greater. quantity of coal shipped. It is the author,', opinion that a movement of slack coal in excess of 3 million tons of coal per year from Utah to any point in central California would justify a freight rate equal to that puhlished for Fontana, Calif.. or $5.05 per ton. The movement of 3 1/2 million tons of coal per year on the basis of 240 mine working days per year would require that 14,600 tons be handled each mine working day. If it is assumed that shipments could be arranged for a 6-day week, the average railway movement would he 11,200 tons, or approximately 3 trains containing fifty-five 70-ton coal cars per day. Such movements of coal would require railroad equipment represented by the investment amounts stated in Table 12 and entail the services of 250 men. Table 12 ... Railroad Equipment and Investment Required To Move 11,200 Tons of Coal a Day from Utah to California Railroad Equipment Cost 2800. 70-ton coal cara at $6.000 each $16,800.000 32 locomotives at $310.000 each. 9.920.000 Miscellaneous eauiument:.......... .5;000:000 Total........................ $31,720,000 It therefore appears that, under presently known mining methods, the lowest price at which coal could be sold f.0.b. the mine in amounts of 3 1/2 million tons per year for generation of power in central California would be $4.60. It also appears that the lowest freight rate that could be expecled between intermountain points and the central California area would be $5.05 per ton, making a total cost of coal delivered at a plant site of $9.65 per ton. Conelusions The following are the author's conclusions: 1. Coal mines in Utah and in the Kemmerer and Rock Springs districts of Wyoming could increase annual production by 6 1/2 million tons per year. 2. Under present conditions coal could probably be delivered to any steam electric plant in central California at a price not to exceed $9.65 per ton. 3. The use of coal at such a price, while higher than the equivalent present price of fuel oil, is entirely feasible. 4. There are adequate railroad facilities for movements of large quantities of coal from the intermountain region to the Rest Coast. 5. In a national emergency it probably would be extremely difficult, if not impossible, to obtain sufficient oil to meet requirements of the greatly expanded West Coast steam electric generatsing capacity. 6. The intermountain region contains ample coal reserves to supply all conceivable demands for West Coast power generation for a number of generations. 7. Increasing demands of labor threaten to lessen, if not eliminate, savings in cost of coal production through the use of new mining machinery. 8. Continuation of experiments in socialism by the Federal Government through construction of hydroelectric generating plants, particularly those unrelated to land-use reclamation, defies justification. Rates under this concept of a governmental function are subsidized through greater taxation of its people. Private capital is available to construct steam plants, or hydro plants where feasible, and should be permitted to continue in order to preserve the principles of our free enterprise system. DISCUSSION (L. C. McCabe and Robert P. Koenig, presiding) C. C;. BALl*—I was asked to lead off the discussion, but it is not with the thought that I might be able to add anything to the paper. The thoroughness with which it was prepared rather forestalls the asking of many questions. Your treatment, Mr. Heiner, is a very valuable contribution. I do want to suggest—that although you have limited your study to this specific question, with certain geographic limitations, many of the things in your paper apply just as well to the eastern coals. I want to agree 100 pct with your final conclusion concerning government-subsidized construction. Id. C. McCabe*—It is certainly worthwhile to take stock occasionally to see where we are going in problems of this nature. I agree with Mr. Heiner that ultimately the only reliable source of fuel that the West Coast has is coal hut the time factor is the difficult element to evaluate. Just before I came here I discussed this subject with N. B. Hinson, Vice President and Executixe Engineer of the Southern California Edison Company, and Chairman of the West Coast Inter-Power Exchange Committee. He has given much thought to utilities' fuel supply and it was very helpful to me in preparing a discussion of the paper to talk with him beforehand. Stock taking and forecasting of future development are essential to the continuing success of any enterprise. Mr. Heiner has called attention to the unprecedented growth of central and southern California and to the increased demands for fuel and power which have accompanied it. He discusses the increased fuel oil and natural gas requirements and the probable limits on the future use of these fuels and of hydroelectric power. In contrast to the calculable limits of these sources of electric energy, the author points to the availability of enormous reserves of coal in the Rocky Mountain States adjacent to the Pacific Coast which can be utilized for power generation. That there will be increased use of coal for power generation in the area under discussion is generally accepted hut it is in the timetable of such development that there is not complete agreement. In a recent report, Mr. Hinson reviewed the future power outlook for the Pacific southwest area. He pointed out that the use of steam plants in connection with water power plants in this region has made the maximum use of hydroelectric energy possible, and that the correct balance between hydro and steam generating plants produces the most economical overall system. Steam plants in the area which had been installed to protect against deficiency in hydro energy in dry years were used to carry war loads. Fortunately, no dry

Jan 1, 1950

By J. B. Hess, C. S. Barrett

TO reach equilibrium between different phases in cobalt-rich alloys requires prohibitively long annealing cobalt-richalloystimes when temperatures are below about 700°C. The fact that a transformation from face-centered cubic to close-packed hexagonal readily tered takes place at temperatures below this in the cobalt-rich solid solutions is not an indication that thermally activated processes occur at an appreciable rate, for the transformation is well established as martensitic in nature. Wide divergence between heating and cooling experiments and high sensitivity to prior heat treatment make it difficult to judge temperatures of equilibrium between the phases.&apos; One object of the present work was to see if the information object of on the relative stability of phases could be gained by substituting plastic deformation for thermal agitation. Procedures were worked out that led to the determination of a diffusionless type of phase diagram, which represents the temperature of of phase equal stability for phases of the same composition, and the technique was applied to the Co-Ni system. Another object of the work was to see whether or not deformation would generate frequent stacking faults when these were thin lamellae of quentstackingfaultsa phase having higher free energy than the parent phase. The alloys were prepared in 80 to 100 g melts from cobalt (with metallic impurities estimated spectrochemically as follows: Ni, 0.05 pct; Fe, 0.001 pct.; Mg, Si, Cu, Cr, Al, < 0.001 pct) and Mond Car-bony1 nickel (with Fe, 0.05 pct; Si, 0.003 pct; C, 0.61 pct.; Cu, 0.001 pct; Co, Cr not detected, < 0.01 pct). The metals were melted in pure Al2O3 crucibles. An atmosphere of argon, that had been purified by passing over hot magnesium chips, was used for the alloys that, by analysis of the portions of the ingots actually used, were found to contain 15.3, 25.7, and 35.0 pct Ni, and vacuum melting (after degassing) was used for those containing 29.4 and 31.5 pct Ni. After induction melting the alloys were allowed to solidify in the crucible, and slices % in. thick x ½ in. in diam were annealed 12 hr at 1350°C for homogenization. These same specimens were used throughout the series of experiments, with annealing treatments of 4 hr at 900°C in purified hydrogen followed by furnace cooling, alternating with the deformation and X-ray tests discussed below. Results Spontaneous transformation was observed on cooling to room temperature in all alloys containing 29.4 pct Ni or less and by cooling the 31.5 pct alloy to — 195°C but was not observed in the 35 pct alloys after cooling to —195°C. These results are in satisfactory agreement with the cooling experiments of Masimoto.4 From these data it is clear that the temperature of beginning transformation M,,, drops to 20°C with the addition of about 30 pct Ni. The test for spontaneous transformation was metallographic. Specimens were thermally polished by annealing 10 hr in hydrogen at 1350°C, then furnace cooled; if trans- formation had occurred there were relief effects visible on the thermally polished surfaces. These markings were narrow straight lines, usually resolvable at high magnification as clusters of fine lines that resembled slip lines. It was concluded that they resulted from displacements on (111) planes, for the number of directions in individual grains often reached but never exceeded four, and lines could always be found parallel to the thermally etched (111) boundaries of annealing twins. The markings were thus consistent with the idea that the transformation occurs by (111) plane displacements (Shockley partial dislocations moving on (111) planes). This was further confirmed by X-ray tests for stacking disorders. Using an oscillating crystal technique previously employed to detect strain-induced faulting in Cu-Si alloys," streaks indicative of the stacking faults were looked for and found on X-ray films of the spontaneously transformed 25.7 pct Ni alloys, as expected by analogy with Edwards and Lipson&apos;s results on pure cobalt." The streaks were much intensified after rolling at room temperature. Transformation induced by plastic strain was investigated as a function of alloy composition and temperature of deformation. A series of tests was made to determine suitable straining and X-raying techniques. Filing was found inferior to abrasion in converting cubic samples to hexagonal, and abrasion was less effective than peening in producing smooth unspotty Debye rings in the X-ray patterns. Because the diffraction lines were broad, Geiger-counter spectrometer records of filings were less sensitive in revealing small amounts of transformed material than X-ray patterns recorded on films in a small diameter camera. After these exploratory tests the following methods were adopted. Specimens that had been annealed at least 4 hr at 900°C and furnace cooled were mounted in a block of aluminum, brought to temperature, and peened thoroughly with a mullite pestle preheated to the same temperature. The specimens were then quenched to room temperature. In peening, a circular area of % in. diam was given 500 blows. A few control tests showed that an additional 1000 blows did not detectably change the proportions of the phases present. The amount of transformation was judged by X-ray reflection patterns from the peened surface, using the innermost four lines of the cubic and the hexagonal patterns with filtered CoKa radiation,

Jan 1, 1953

By H. S. Munroe

The accompanying figures illustrate the dumping-device used at the new dressing works of the St. Joseph Lead Co., at Bonne Terre, Mo. It is a dumping-cradle, of a type much used abroad, in which the car is turned upside down to discharge its load. The main

Jan 1, 1889

By AIME AIME

THE Employment Bureau of the F. A: E. S., conducted under- the direct supervision of the secretaries of the four Founder Societies, has wanted to extend its activities and usefulness but it is operating right up to the limit of its budget; consequently, anything which requires the expenditure of more funds cannot be -undertaken, for the present. A great deal of time has been spent in recording, classifying, and interviewing the men listed, but owing to the business depression, only a comparatively small number of men have been placed&apos; luring the last few months. There are men in New York from all over the country. What the Bureau needs is more positions available. With this in view, a number of high-grade engineers, themselves in need of employment, volunteered their services for a publicity campaign in the City of New York. A definite mode of procedure was evolved, and the success of the movement has been considerable, so much so that it has been thought well to call it to the attention, of members elsewhere, so that similar committees &apos; and campaigns might be organized in other cities. Following is a chronological arrangement of the methods used.

Jan 1, 1921

By J. Murray Riddell, George A. Morrison

This paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.‡ Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Bar-berton constitutes the world&apos;s deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 2-40 ft. Fractured sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra- turn of oil-bearing sandstone one foot thick was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), ? by 4 by 4-in. angle irons; spacing of sets. 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. The Shaft-sinking Operation The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (1) a storage pocket of 300 cu. ft, capacity with truck servicing facilities, and (2) pneu matically operated dump doors, which mere actuated by the hoistman, thus caring

Jan 1, 1946

By Joseph G. Wargo

A meteoric rise in selling price has revived gold exploration activity throughout the world. In the United States the effort is, in large measure, channeled toward discovery of disseminated gold deposits such as the Carlin-type, i.e., with size and grade characteristics similar to Newmont&apos;s Carlin mine in Nevada. The subtle surface indications characteristic of Carlin-type gold mineralization have been examined by a number of geologists, and the more obvious prospects have been tested by surface sampling and drilling. It is likely that most of these readily recognizable deposits have already been found and, as a consequence, prospectors are now entering a new, second stage of exploration for Carlin-type and related disseminated gold deposits.

Jan 9, 1979

By Persifor Frazer

From the easternmost point reached by the Ural excursion of the VIIth International Geological Congress (the city of Tschéliabinsk, a little more than 30&apos; of longitude east of St.

Jan 1, 1899

Following the usual custom, three meetings are planned for the year. The Mid-Continent meeting will be held at Oklahoma City, Okla., Oct. 7 and 8, and the California meeting is planned for Los Angeles, probably also early in October. A program along the usual lines is under way for the annual New York meeting. Discussion and planning of the year&apos;s activity started in March. An effort is under way to secure papers dealing with some overlapping phases of engineering, petroleum geology, geophysics, law, economics, refining, etc. The main reason for attempting a program along these lines is the belief that unusually interesting technical papers can be obtained. The degree of specialization in the technical and related fields has permitted but few individuals to develop a sufficiently comprehensive viewpoint. Also, at times the developments in a particular field are capable of giving great stimulus toward much needed solutions of difficult problems in others fields of activity. With the coming of the period of restriction of production to market demand, many changes have occurred in policy and technique of petroleum production. Some changes have been advances, others have been of retrograde nature. It seems doubtful whether the adjustment to the condition of excess producing capacity has been complete or sound in some major respects. Many changes are in progress and others need to be initiated. The industry has excessive producing capacity so far as immediate market demand is concerned, but reserves for several years hence are generally believed insufficient. Exploration and discovery should go forward but development should proceed with caution and under control. Property rights should be clarified and protected for the new condition— without excessive cost for drilling wells that serve no purpose except that of giving some protection to property rights at the cost of an increased price to the consumer. Under the more steady condition of assured supply for the immediate future, as compared to the hand-to-mouth condition of wide-open production, a greatly advanced technique of development and production is possible and is being developed. Great progress has been made, but much remains to be done. Along some important lines progress can be effected only by better understanding between the engineer and the geologist, the lawyer, the politician, the geophysicist, etc. There is need

Jan 1, 1937

Jan 1, 1940

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

CERTAIN titanium alloys when quenched to retain the 0 phase at room temperature show extensive transformation of 0 to martensitic a during deformation. Alloys of this type are usually characterized by low tensile yield strength, a large spread between yield strength and ultimate strength, and high uniform elongation. A previous investigation of this phenomenon concluded that the principal contribution of the martensitic transformation was to increase the amount of deformation prior to fail-

Jan 1, 1964

[ ]

Jan 1, 1938

Elected Died 1884 *ADDY, MATTHEW 1896 1894 *ALLFN R B 1896 1874 *AMIOT, H 1892 1886 *AMSLER, CARL 1894 1895 *ÅNGSTROM, CARL 1901 1895 *ARMSTRONG, JOHN F 1898 1882 *ARNOLDS, HUGO 1886 1875 *ASHBURNER, CHARLES A 1889 1872 *ASIIBURNER, WILLIAM 1887 1883 *ATKINS, C M , JR 1885 1897 *AYERS, WILLIAM 1898 1885 *BABCOCK, GEO H 1893 1884 *BAILEY, EDWARD 1889 1880 *BAILEY, JACKSON 1887 1900 *BALLOU, FRANKLIN 1903 1886 *BARNES, F W 1892

Jan 1, 1910