Search Documents

By H. H. Smith, G. J. Danek, M. R. Achter

Nickel, Type 316 stainless steel, and copper show decreases in reversed bending fatigue strength with increases in air and oxygen pressure. The leveling off of the log N us log p curve for nickel at 300" and 816°C is discussed in terms of a model in which surface saturation gives rise to a critical pressure. A metallographic study indicated that the effect of environment on crack initiation and growth rates is a function of temperature. It is shown that small amounts of impurities in inert gases may substantially reduce the fatigue strength of nickel. 1n a previous investigation1 of high-temperature bending fatigue in air and in vacuum, reversals in the effect of environment with changes in test conditions were atrributed to a mechanism consisting of two processes acting in competition. One of them, oxidation strengthening, has been demonstrated in a straightforward manner by measuring the rupture strength of a sintered nickel-oxide bond.' The detailed operation of the other process, facilitation of crack propagation by surface absorption of oxygen, is uncertain. Thompson et UZ advanced the possibility that the formation of an oxide layer prevented rewelding of cracks during the compressive part of the cycle, while Wads worth and Hutchings4 further proposed that the reaction of oxygen with atoms at the tip of the crack helped the metal to break there, a possibility which has also been advanced to explain crack formation in creep.5 A difficulty in arriving at a mechanism for this lowering of fatigue strength in air is the inconsistency of some of the data. For example, Wadsworth and Hutchings4 found an approximately linear decrease of log cycles-to-fracture (N) with an increase of log pressure-of-air (p) for copper and aluminum at room temperature, while snowden,' although finding a similar linear dependence for aluminum, observed a stepped curve for lead. Between l0-' and 10"1 torr there is a sharp decrease in the fatigue life of lead with increasing air pressure, but plateaus, signifying no dependence on pressure, are found at higher and lower pressures. If, as discussed elsewhere: these environmental effects arise from the adsorption of gas on crack surfaces, it would be expected that as the pressure is increased a saturation point would be observed, beyond which there is no further effect. To gain further information about the form of the log N vs logp curve, it was decided in the present investigation to repeat this type of measurement at elevated temperature on nickel, copper, and Type 316 stainless steel. An additional object of this program was

Jan 1, 1963

By E. E. Wark, J. Rogers, I. W. Wark, K. L. Sutherland

SOAPS have been used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xanthates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present eminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies.[t] A broad, semi quantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. THE PARAFFIN CHAIN SALTS The basic requirements for a "collector" in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polarnonpolar compounds is the paraffin chain salts: CH3(CH2) „X where X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -CO2Na, -SO3Na, -SO4Na, - PO4Na2, or an aminonitrogen group, the

Jan 1, 1946

By J. Rogers. K. L. Sutherland, E. E. Wark, I. W. Wark

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By E. E. Wark, I. W. Wark, J. Rogers. K. L. Sutherland

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By P. G. Shewmon, J. Y. Choi

The surface-diffusion coefficient for , has been measured on (111) and (100) surfaces of copper from 1000" to 620°C. D,(Ge) on the (111) is two to three times that on the (100) as was found earlier for copper and gold on copper. D, (Ge) on both (111) and (100) is about thirty times that found for gold or copper tracers on the same surfaces, while in the temperature range where both D,(Ge) and Ds(Au) have been measured the activation energy for germanium is the same as that for gold. The apparent activation energy for Ds(Ge) is not a constant, but decreases with temperature. In a recent paper we reported on the application of a new tracer technique to the determination of the surface-diffusion coefficient (D,) for gold and copper on (111) and (100) surfaces of copper.' In this paper, we shall give the results obtained when the same technique was used to measure Ds for germanium on the (111) and (100) surfaces of copper. In addition to providing data on D., for an additional element on copper, the longer half-life of germanium (275 days) meant that Ds could be measured down to a much lower temperature and thus over a much wider temperature range (1000" to 620°C) than was used in our gold-tracer work (1060" to 780°C) or copper mass-transport studies (1060" to 800). The apparent activation energy for D, (Ge) is essentially the same as that found for gold or copper in the same temperature range, though the values of D, (Ge) are thirty times greater than those found for gold or copper tracers. The most interesting new result found is that the apparent activation energy for Ds(Ge), and thus Do, definitely increases with temperature. Such a trend was much more apparent in Gjostein's mass-transport work on copper than in our own, though in an earlier paper we mentioned the difficulty of fitting all of our points with one straight line:= No real explanation of this is given though experiments done on grain boundary groove growth at various ambient pressures demonstrate unequivocally that vapor transport plays no part in the increase in activation energy with temperature.

Jan 1, 1964

By R. S. Dean

THE commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in MINING AND METALLURGY for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for "the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. PRACTICE AT BOULDER CITY The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: I. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By Carl S. Westerberg

Coal preparation practice and trends follow, among other factors, production trends in any given area. Considering an area the size of a state, some broad predictions may be made after a review of the annual production records. As this paper is concerned with coal cleaning in Utah, data on its production record are pertinent. Table 1 shows the percentage relation of coal production in Utah to the national total as a single figure up to 1935 which includes all recorded production. From 1935 through 1947 these data are presented by years. It is evident from these data that the production of Utah coal is ascending. The reason for this trend is industrial growth in the West resulting in a population shift which accounts for more people than the normal increase would supply together with Utah's relatively fortunate geographical location and its abundance of good-quality coal. Utah is also hopeful of supplying more coal in the future for West Coast power generation.I Utah is not unique among coal-producing states in anticipating greater production in the future. Coal Age states, " . . . it is now evident that a billion-ton yearly production of anthracite and bituminous by 1960 is not impossible." At present it is about 610,000,000 tons, the all-time high in 1947 was approximately 687,803,000 tons. In view of the trend outlined above, obviously more new mines will be required to produce the necessary tonnage. These in turn will require more mechanical cleaning capacity. Whether the required new plants will be built by present operators of mines and mechanical cleaning plants or by others now in the business of producing coal or expecting to enter it is of no consequence in this discussion. The fact is— they will be built.

Jan 1, 1950

SEVERAL distinctions can rightfully be accorded the Bagdad enterprise. For one thing, it has the most romantic name among the Porphyry Coppers and this is said with all due deference to Copper Queen and Inspiration! Bagdad was one of the richest and most magnificent cities of the glamorous world of the Arabian Nights. The record does not say who was responsible for applying the name Bagdad to the company that in 191 1 took over the property of the Arizona-Nevada Copper Company; but whoever it was must have had visions (or at least hopes) of a fabulously profitable mine. So far as I know, Bagdad is the only Porphyry whose owners, or officials, ran afoul of the law because of alleged sins of omission or commission in vending shares of the company's stock. E. B. Bronson, of New York, had been interested in Bagdad since 1909; and, during the lean period of the 1930's he had, as president of the corporation, endeavored to raise needed funds by the sale of 140,000 shares of treasury stock. Some legal questions arose as to the need for registration under the Securities and Exchange Act; but, when Mr. Bronson finally filed a registration statement, the New York office of the Securities and Exchange Commission found 155 "deficiencies" in the document. According to the judge who later heard the criminal case against Bronson, no evidence was introduced to show that he had personally benefited "to the extent of one dollar." However, it was charged that the setup was such that he was in position to profit if he had wanted to! A somewhat quixotic position, it would seem. In any event, he was convicted, on highly technical

Jan 1, 1957

By W. L. Maxson

GRINDING is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grind-ing installations. There have been some tests published, notably those of Lennox,1 which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was .then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the compari-sons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating, load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to he expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method.

Jan 1, 1933

By Donald C. Moore

INTRODUCTION Published laboratory procedures used by the major crusher manufacturers for estimating crusher size are based upon techniques developed in the mid 1940's. Specifically, the two largest U.S. crusher manufacturers are using the Bond impact procedure. Although the procedure is still in use, there is little confidence in the results. Unless the laboratory results fall within a preconceived range, personal experience is used for selecting the number of crushers and connected horsepower (Coleman, 1978). There have been numerous theoretical studies of the communition of particles. However, no procedure has been widely acclaimed for predicting crusher power requirements. Experimental studies have included breakage by slow compression, slow speed impact and high speed impact. Theoretical results have increased our knowledge of the comminution process, but the procedures have not been capable of analyzing the complex mechanism of industrial crushing machines. The purpose of this chapter is to review the empirical crushing procedures that have been used, including advantages and disadvantages. A new procedure which has been in development at Allis-Chalmers Corp. from 1977 to 1982 is detailed. Actual results of the new procedure on a concentrator feasibility study are included. EXPERIMENTAL GOALS The goals of a laboratory crushability procedure are accurate predictions of: (1) Rock crushability, measured as energy per unit mass. (2) Crusher product size analysis. A procedure capable of predicting these parameters should be inexpensive and require a minimum amount of sample. CRUSHABILITY TESTS Bond Impact Procedure F. C. Bond (1946) detailed the development of the pendulum impact device that is still used by the leading crusher manufacturers (Bond; Rexnord, 1976). The device (Fig. 1) is comprised of two bicycle wheels with 13.6 kg steel hammers tangentially attached to the rims. The hammer faces are 50 mm apart at rest. On opposite ends of the hammers lifting

Jan 1, 1982

By H. C. Vacher, C. J. Newton

EXTENSIVE investigations in the field of residual strain measurement by X-ray diffraction have been made by Bollenrath, Hauk, and Osswald,1 by Smith and Wood,2'3 by Greenough; by Rosenthal and Norton." and many others. Since X-ray strain measuremeits apply only to those crystals of the test body which are of the proper condition and orientation to diffract and since the residual strains revealed may be accompanied by either body or tex-tural stresses, there has been considerable disagreement among investigators with respect to the validity of conclusions in this field. Although the experi-mentors have employed a variety of loading schemes, surface preparations, and X-ray wave lengths, the observations almost invariably have been made only on the outer surfaces of the specimens. The present note is not to be construed as an exposition of a new method of stress analysis by X-ray strain measurements on sections but as a presentation of some results which point to interesting possibilities for further experiments with sections. The two test rods used in this study were of ingot iron annealed at 910°C. The initial length of the gage section was 2 in. and the diameter was 0.415 in. Cross-sections were cut from the ends of the annealed rods to provide strain-free material. The tensile rod was axially loaded the desired amount in a commercial testing machine. A 1 in. portion of the gage length was cut from the other rod and was subjected to compression in the same machine. Details of this plastic straining of each rod are given in the upper half of Table I. A half-cylinder piece about 1/4 in. long was obtained by making a short longitudinal plane cut containing the axis of the rod near the center of the gage length. From adjacent material a disk about 1/8 in. thick was cut to provide the cross-section specimen. Later another section was cut from this same region with an angle of 30" between the normal to its surface and the axis of the test rod. A cross-section and a longitudinal section were cut from the compression rod in a similar manner. All of these as well as the strain-free cross-sections were mounted in Bakelite and used as specimens for the following X-ray strain measurements. During the course of the study, it became apparent that the condition of the surface of a specimen was a highly critical factor. One of the annealed strain-free specimens as a control was subjected to about 24 hr of polishing with fine alumina, interrupted about every 2 hr for etching with 1 pct nital. Its lattice parameter was determined at intervals from measurements on back-reflection X-ray diffraction patterns, which were calibrated with diffraction from tungsten powder. The parameter gradually approached the value found in the literature for strain-free iron and remained there, within the limits of the experimental error. This determined a long polishing and etching procedure which was adopted for all the specimens and which gave X-ray results from the surfaces believed to be representative of each specimen as a whole. A large number of back-reflection patterns were made with cobalt and chromium radiation, all at normal incidence. Except for some preliminary stationary exposures made to monitor the removal of cold work from the surfaces, each exposure was made with the specimen slowly translating and the film slowly rotating. In appropriate cases a thin layer of a standard metal powder, tungsten with cobalt radiation and silver with chromium, was dusted over a film of vaseline on the surface of the specimen to serve to calibrate the X-ray patterns. After the preliminary work, four films were made,

Jan 1, 1956

By Jennifer Drake, Edward T. Moriuchi, Jennifer A. Hill

SEAMSYS and CSD/SMP are sets of computer programs that assist geologists and mine engineers in modeling and evaluating coal properties. The systems are tailored for treatment of waste and coal quality data, including metallurgical coal product capabilities. The gridded SEAMSYS model honors all drillhole data and incorporates user- defined mining parameters, losses and dilutions, and operational constraints. A variety of reserve reports and graphic displays are available from the model. Preliminary mine planning is accomplished through automatic cut generation and production targeting. CSD/SMP refines the preliminary plans to help anticipate the consequences of various mine schedules and evaluate equipment capacity requirements.

Jan 1, 1983

By H. H. Pentz

THIS paper gives the derivation of a practical formula for the calcu-lation of slopes in seismic reflection prospecting. The derived formula is an approximation and can be used where the slope of the reflecting horizon is less than 250 ft. per 1000 and the depth to the reflecting horizon is greater than 2500 ft. The slope of sediments in oil regions is generally considerably less than 250 ft. per 1000. This is particularly true of the Gulf Coast, with the exception of the salt domes, which usually have the sediments at a greater slope than 250 ft. per 1000.

Jan 1, 1937

By Alden B. Greninger, Alexander R. Troiano

THE crystallographic mechanism for the austenite-to-martensite transformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite-and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite undergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.-Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about -70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of I mm. or more. Four martensite cystals from four different ingots were prepared in this manner; the largest crystal of this group is illustrated in Fig. I. Back-reflection Lane patterns were obtained from martensite [ ] crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution (±0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to {112} and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Harold Vagtborg

Equilibrium vaporization ratios were obtained for light hydrocarbons, nitrogen, carbon dioxide, and hydrogen sulfide in a reservoir fluid containing 35 mole per cent hydrogen sulfide. The data cover the range from 700 to 2500 psia at 154°F. The results of this study are compared with results obtained by other investigators on systems containing less hydrogen sulfide. When large amounts of hydrogen sulfide are present, the equilibrium vaporization ratios for ethane and heavier hydrocarbons are greater than the ratios for systems containing little or no hydrogen sulfide. Large amounts of hydrogen sulfide have the reverse effect on the ratios for methane. Routine PVT studies were performed on the reservoir fluid including flash and differential liberations of the dissolved gas. The pressure-volume relationships of the saturated fluid were also determined. It is shown that the use of published correlations on physical properties of reservoir .fluids can lead to gross errors when applied to systems containing large amounts of hydrogen sulfide. INTRODUCTION Equilibrium vaporization ratios for various components in naturally occurring crude oil and condensate systems have been reported in the literature.1,2,3,4 Recently, several papers have been published with emphasis on non-hydrocarbon components such as nitro- gen, carbon dioxide and hydrogen sulfide.5,6,7,8,9 The increased discovery of reservoir fluids having high concentrations of these non-hydrocarbon components, particularly hydrogen sulfide, has created a need for a further study of their phase behavior. Equilibrium vaporization ratios are known to vary with pressure, temperature, and overall composition of the system.'" It was anticipated that ratios for systems containing large amounts of hydrogen sulfide would differ from the ratios for systems containing small amounts of hydrogen sulfide. Therefore, the present work was undertaken in order to obtain reliable equilibrium vaporization ratios for the reservoir-fluid in question. PROCEDURE The procedure followed was evolved after considerable experimentation on methods of handling the very sour crude. It was found that drying agents (e.g. CaCl2 and CaSO4) absorbed an appreciable amount of hydrogen sulfide from the gas used to prepare the recombined samples. The concentration of hydrogen sulfide dropped as much as 10 mole per cent in a single pass through a 3-ft drying tube. It was also found that when undried gas was agitated with mercury in the PVT cell, a black scum, believed to be mercuric sulfide, was formed and the hydrogen sulfide content of the gas dropped several mole per cent. Because composition changes during a run could not be tolerated, separation of the mercury and sour fluid was necessary. In order to effect this separation, a stainless steel piston, equipped with Teflon O-rings, was placed in the PVT cell between the mercury and the sour fluid. This piston had to be constructed in three parts because

Jan 1, 1955

By J. C. Landenberger

Freezeproofing waste dump cars during winter months has long been of concern at Kennecott's Utah Copper Div. open pit property. Waste mining operations at Bingham Canyon use trains of seven 40-cu yd side-dump railroad cars with electric locomotives to service stripping shovels. Waste is transported an average of nearly 3 miles from the mine benches to dumping areas. During winter months, usually beginning in late October or early November, intermittent and continued periods of freezing together with varying amounts of snow cause waste material to freeze or stick to the sides and bottoms of the cars. Because of the physical layout of the pit, it is not feasible to freezeproof all waste trains at one or even a limited number of locations. A waste haulage line usually serves one or two mine benches, so that freezeproofing facilities must be maintained at many locations. For example, at the time of writing 27 salting stations were in use.

Nov 1, 1955

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956

By J. K. Edgar

For a number of years the production and use of super-purity aluminum (better than 99.99 pct) has been steadily increasing. High-grade lots of. such aluminum show certain outstanding characteristics not found in lower grades containing principally silicon, iron and copper as impurities. One such characteristic is the so-called "self annealing," that is, the re-crystallization of the heavily cold worked metal at room temperature.' Interest therefore is aroused as to the effects of the impurities. It is well known that the amounts of silicon and copper which occur in aluminum of better than 99.95 pct are completely soluble, at least at elevated temperatures (above 200°C). Iron, on the other hand, is known to be fairly insoluble in solid aluminum. Thus, a knowledge of the limits of this solubility would he of considerable use in studying the characteristics of the high purity metal. All investigators have agreed that iron has very low solubility in solid aluminum. Rosenhain, Archbutt and Hanson2 reported traces of an aluminum-iron phase in the "purest samples of aluminum obtainable." Gwyer and Phillips3 reported that an iron constituent was visible under the microscope in metal containing ".0088 per cent iron." Roth4 found that in the solid state the solubility of iron in high purity aluminum was 0.01, 0.01, 0.017 and 0.022 pct at 225, 320, 500 and 600°C respectively. Dix5 working with alloys containing less than 0.03 pct impurities, concluded from microscopic and chemical analyses of eutectic areas that the eutectic composition was close to 1.7 pct iron. Dix placed the eutectic temperature at 65s°C. Archer and Fink,6 using high purity aluminum-iron alloys, found that the hypoeutectic liquidus intersects the eutec-tic horizontal at 1.7 pct. This is in fair agreement with the investigation of the aluminum-iron system by Gwyer and Phillips who placed the eutectic at 1.89 pct iron with a freezing point of 653'C. Preparation and Chemical Analysis oP Alloys Electrolytically refined aluminum (99.991 pct aluminum) and a high purity alumi-num-iron alloy (11.45 Pet iron) were used in the preparation of the alloys for this investigation. To aid in controlling the iron content of the experimental alloys, an alloy of lower iron content was prepared first from these materials. The high purity aluminum was melted and heated to about 700°C in a plumbago crucible coated with alundum cement and the aluminum-iron alloy was then added. The alloy was thoroughly stirred, fluxed and skimmed and then chill-cast into notch bars. The aIlalyses of the three materials are given in Table I. The alloys for the determination of the solid solubility of iron in aluminum were prepared by melting 600 g total of the aluminum plus the required quantity of the aluminum-iron alloy (No. 92531). These

Jan 1, 1949

By Roger E. Barthelemy

PRIMITIVE mining and metallurgy has today almost disappeared. Probably the only remaining tribal tin mining and smelting is practiced by the Laotian natives in one of the less known tin areas of the world. This district lies almost a thousand miles from the sea along the Mekong River, one of the longest rivers in the world, that marks the border between Siam and Laos, one of the five states forming French Indo-China. Less than twenty years ago it took more than two weeks' travel on elephant-back to reach the spot and today it still takes many days of travel, using all kinds of transportation from automobiles to native

Jan 1, 1938

By J. L. Huitt

Some of the problems associated with the acid treatment of oil wells are related to the control of the composition of formation treating acid. One test usually made at the well site is the determination of the acid concentration. Heretofore, the concentration of the acid delivered to the well site usually has been interpreted from a hydrometer measurement of the specific gravity of the acid solution. Experience has shown that this indirect measurement of acid concentration can give erroneous results. More reliable results are, of course, obtainable by the titration method; however, this method is not easily adapted to well-site testing. To overcome these objections, a device was developed for use in the field which permits determination of the concentration of treating acid both quickly and accurately at the time of the acid treatment. Its purpose was three-fold, namely, to determine: (1) the concentration of the fresh treating acid, (2) the concentration of the spent acid returning from the well, and (3) the solubility of formation samples in treating acid. The device was designed to operate on the principle of the stoichiometric relation between the calcium carbonate—hydrochloric acid reaction and the carbon dioxide gas resulting from the reaction. By confining the carbon dioxide gas within a reaction cell of the type shown in Fig. 1, the pressure inside the cell is increased. Since the pressure is an indication of the quantity of carbon dioxide gas produced, it may be used to estimate the concentration of the acid, provided an excess of calcium carbonate is used. From information on the volume of the reaction cell, the volume of acid used, and the pressure and temperature of the gas after the completion of the reaction, the concentration of the treating acid may be computed. The reaction cell is essentially a pressure vessel equipped with a pressure gage, temperature indicator. pressure release valve, and a special sample holder. Plastic and metal construction makes the cell both rugged and acid-resistant. The sample holder is so designed that a sample of calcium carbonate (or sample of carbonate rock) can be dropped into the acid

Jan 1, 1956