Search Documents

By W. H. Gross

To pollute means to make impure or unclean. We tend to forget that man defecates, urinates, sweats, expectorates and exhales and in himself is a beastly little pollutor-but then so is Mother Nature! The object of this paper is to try to put what man and nature do into perspective. The facts indicate that although man may sweat a little, Ms. Nature is by for the greatest pollutor of all.

Jan 1, 1979

By Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY?s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By R. J. Mitchell

"A lest apparatus has been developed for obtaining the relations among confining stress, porosity and percolation rate for hydraulic sand backfills. The apparatus can also be used to evaluate internal drainage characteristics and the effects of partial saturation on percolation rates. The test apparatus, test procedures and typical test data are presented in this paper.IntroductionAlthough the standard percolation test has become an accepted method of evaluating the drainage characteristics of hydraulically placed tailings backfill, it is recognized that the test results require considerable interpretation due to the following factors: (I) The results can be markedly influenced by varying sample preparation procedures, which vary the amount of material segregation in the sample . In particular, a thin layer of slimes on the top of a sample can control the flow of water into the sample. Wall edge effects can also affect the test results. (2) The in-place porosity of the backfill is not duplicated in the test sample and empirical formulae must be used to estimate the variation of percolation rate with porosity. (3) Internal drainage characteristics and the percolation rate of partly saturated fill cannot be evaluated in the standard percolation test.In addition to eliminating these problems, the compression percolation test apparatus also provides additional data on the mechanical properties of the backfill. Compressibility (or bulk modulus) is measured at different stress levels during the course of a test and this information can be used in evaluating the usefulness of the fill in providing ground control and in limiting ground subsidence. The engineering design of mine backfill is becoming an important part of the over all design of underground mine operations. The design problems are sufficently different from conventional civil engineering soil mechanics problems that new test methods and design procedures are required."

Jan 1, 1981

By Tapio Leskinen, Jouko Koskinen, Timo Nlltti, Lappalainen Seppo, Pentti Vanninen

"The Courier 300 on-stream analysis system manufactured by Outokumpu has now been in operation at five of the company's concentration plants long enough to give a reliable basis for closer examination of the benefits achieved in control of these processes. The first system was installed at the Pyhiisalmi mine at the end of 1967. Since November 1970, two analyzers have been in operation at Pyhiisalmi feeding the assay data to a process computer which controls the whole plant and does the optimization of the process. In October 1970 the Courier 300 analysis system was installed at S. T. O. LESKINEN J. KOSKINEN the Keretti concentrator of the Outokumpu mine, followed soon by installations at the Vihanti Mine in May 1971, at the new Vuonos mine in November J 971 and at t he Kotalahti mine in December 1971. Since installation of the Courier analysis systems, considerable improvements have been achieved in the control and the economy of the plants. Immediate knowledge of the changes in the process and the possibility for rapid action has resulted in evener production and higher capacity and recovery. The recovery has been increased most significantly at the Vihanti concentrator, which operates on a complex ore. Consumption of chemicals has been reduced at all concentrators. Due to the fact that process control and partly also bilance analysis are not achieved by conventional methods any more, it has been possible to reduce the personnel of the laboratories drastically. Two of the plants, viz. the Pyhiisalmi and the Vuonos concentrators, are computercontrolled. The Vuonos concentrator started operation in January 1972 under computer control from the very beginning. The Pyhiisalmi concentrator has been computer-controlled since 1970. The Courier 300 analysis system was described in detail at the AIME Centennial Annual Meeting (1971). In this paper, less attention is paid to the analysis system. Only the sampling system of the Courier 300 is described in more detail. In the development of sampling equipment, effective use has been made of the company's wide knowledge of the problems involved and the test field offered by its concentrators. The sampling equipment includes secondary samplers and six basically different types of primary samplers, with which most sampling situations can be managed."

Jan 1, 1973

By Neil Campbell

Abstract Following discovery on the Giant property of very promising gold deposits, some of which terminate against the steeply-dipping West Bay fault, a geological study was initiated co locate possible faulted extensions of the ore. Geological mapping revealed that the ore and the shear zones to which the ore is confined are older than the fault and therefore subject co displacement by it. It also disclosed several diabase dykes which seem co provide the best basis for determining the fault movement. After applying various techniques co determine their strikes and dips, the dykes were used as structural markers and it was estimated that, subject co certain possible errors, the movement on the fault was 16,140 feet (3.06 miles) south and 1,570 feet (0.297 miles) down on the west side relative co the ease. Evidence supporting this conclusion was obtained when subsequent deep diamond-drill holes intended to test the hypothesis cut an ore-bearing major shear zone which, so far as can be determined, is nearly identical with its present correlative on the Giant property. Introduction The fault under consideration follows a northerly trend past the west side of the original settlement of Yellowknife, which is situated 600 miles north of Edmonton and 400 miles from the Northern Alberta Railway terminus at Waterways, Alberta. The mining properties chiefly concerned include the southern part of the Giant claims, on the east side of the fault, and the Con-Rycon-Demelt claims, on the west side, 3Y2 miles to the south. Geological data were also obtained from the eastern part of the A. Y.E. property, which lies south of the Giant claims, and from the Negus, Meg, Yellorex, and Kam properties, which are south and southeast of the Con-Rycon-Demelt claims. Recognition of the major faults in the Yellowknife Bay area, including the West Bay fault which appears to be the greatest, resulted from the work of Dr. A. W. Jolliffe (McGill University, formerly of the Geological Survey of Canada) in 1935 and subsequent years. It has been stated with little exaggeration that these faults rank with the largest known steeply-dipping dislocations of the earth's crust. In the winter of 1939, a mineralized shear zone named the Creek Vein was found on the Giant property. It was noticed that the space relationship between the new shear zone and a body of quartz-feldspar porphyry is roughly the same as that between the Con C-4 shear zone and a body of acidic flows lying north of the Con property. Coupling this relation with the assumption that the movement along the fault is dominantly horizontal, it was postulated that the Giant shear zone represented the faulted extension of the Con C-4 shear.

Jan 1, 1947

By R. Boom

Corus Umuiden, formerly Hoogovens, was the first steel plant in Europe after Voest to introduce oxygen steelmaking. In the decision-making process contacts with Dofasco in Canada about the production of formability steel grades were crucial. In developing oxygen (LD-) steelmaking high liquid steel output rates had to be combined with accurate process control. For ingot casting static models with input control and sampling during interrupted blowing were sufficient to deliver liquid steel within the required carbon, phosphorus, sulphur and temperature windows. Computers were introduced to perform the complicated charge calculations. Continuous casting called for strict control of composition and temperature at process end point and made predictable timing crucial. Dynamic control was introduced based upon sub lance measurements and waste gas analysis. Reliable disposable measurement sensors were developed in a concerted international action. Dissolved oxygen at blow end deteriorated the quality of low carbon aluminium killed steel grades. Blowing gases through the converter bottom improved process kinetics, resulting in lower carbon-oxygen products, yield increase and better phosphorus removal and generated new families of hybrid blowing processes. Introduction of secondary metallurgy facilities such as argon stirring stations, vacuum degassers and ladle furnaces relieved the demands for strict BOF end point control. Desulphurisation of hot metal became standard practice. In regions with scrap shortage hot metal desiliconisation followed by dephosphorisation, was introduced in the blast furnace cast house and hot metal transfer ladles. Later redundant converter vessels were used for pre-treatment, resulting in a two-stage process. The fundamentals of oxygen steelmaking are described and a vision on the future is presented.

Jan 1, 2004

By B. W. Smee

Glacial lake sediments or glaciolacustrine deposits form a significant portion of the Canadian, Scandinavian and Russian landscapes. Furthermore, 50 per cent of the Archean volcanic belts within the Canadian Shield area are covered wholly or in part by these deposits. Because of the high electrical conductivity and low hydraulic conductivity of these compact sediments, the application of geophysical (electrical) and geochemical techniques in such areas becomes a difficult task. The presence of these sediments has therefore hampered exploration for metallic sulphide deposits in some of the most important metallogenic environments of Canada. Similar problems exist in some tropical countries, such as Australia, where the overburden may be very conductive. In this paper, the extent and provenance of the glaciolacustrine deposits within the Canadian Shield are described. The geochemical and geophysical factors that hinder exploration in the clay belts are reviewed, with case histories of successful and unsuccessful applications of some of these techniques. The most successful geochemical technique used within glacial clay belts is the sampling of lodgement till beneath the clay cover, and the analysis of the heavy mineral fraction of that till. Surficial sampling has not been successfully applied. Some geophysical techniques, more specifically electromagnetic and magnetic induced-polarization techniques, have detected mineralization beneath substantially deep clay or saline overburden layers. Some suggestions have been made, such as the use of anions in hydrogeochemical surveys and the use of wide-band multi-frequency EM systems. When implemented, they will hopefully make the current geochemical and geophysical methods more effective in exploration for base metal sulphides within clay-covered terrains.

Jan 1, 1979

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By John J. Deutsch

"1T is a great pleasure for me to be present at the Annual Dinner of the C.I.M.; a pleasure which is combined with a mutual opportunity that I value highly. First of all, this occasion gives me a chance to meet again many Members of your Institute and to become more fully informed of the special problems of the mining industry. This alone is ample reason for me to welcome the invitation to join you tonight. In addition, this occasion provides me with an opportunity to tell you something about the work of the Economic Council which might be of particular interest to your industry.In the mining industry, keen competition and constant change are basic facts of life. The continuing prosperity of the Canadian mining industry depends fundamentally on how successfully it is able to adapt both to the changing conditions within the industry and to major trends which operate throughout the world.First of all, the scale and organization of the industry are evolving to new and different dimensions. As one authority has put it, ""The cream of the small high-grade, easy-to-mine ore deposits of this world have been consumed and mining is becoming more and more an industry of very large scale, complex operations. It has already become in most countries a capital intensive industry and its problems, scientific, technical and economic, are growing in difficulty."""

Jan 1, 1966

By D. W. Euler, D. G. Brophey

"In an attempt to address the issue of rising labour costs, and to improve productivity, a laser-based system to guide underground LHDs and trucks has been developed. This comprehensive system is known as the Opti-Trak system.Essentially, the vehicle is equipped with front and rear-mounted lasers which scan a reference strip mounted on the drift back. The vehicle follows this reference strip and in addition, based on reflective bar codes mounted beside the reference strip, initiates certain functions (i.e. dump cycle, speed change, brake check, etc.). Any programming that is drift-specific is handled by the positioning of the reference strips and bar codes. Consequently, the vehicle can easily travel to many different haulageways or branches, providing the reference strip and bar codes are in place.The advantages of this system are an immediate elimination of haulage operator costs and an increase in available hauling time to 7 hours out of an 8-hour shift as compared to the typical 5Y2 out of 8 hours that a manned haulage system offers.This paper describes the Opti-Trak system and the benefits to be realized from automation of mine haulage requirements."

Jan 1, 1994

By W. J. Farley

Location and History The Sherritt Gordon mine is in northern Manitoba, one hundred miles north of The Pas and forty miles northeast of Flin Flon. The original discovery was made by a Cree indian, Philip Sherlett, in 1922. The claims lapsed in 1924 to be re-staked and optioned by various mining groups who carried out a certain amount of development work before relinquishing their options. In 1927 the present Company, Sherritt Gordon Mines, Limited, was formed to take over the property. Production commenced in 1931, but in the following year operations were suspended and it was not until 1937 that the prevailing price of copper pemitted resumption as an economic operation. The mine has operated continuously from that time to the present. Total production to the end of 1947 has been: Copper . . . . . . . . . 301,813 . .,345 pounds Zinc . . . . . . . . . . . 112,636 tons of concentrat (50% zinc) Gold . . . . . . . . . . 83,070 ounces Silver . . . . . . . . . 2,651,317 ounces General Geology The consolidated rocks in the vicinity of the mine, all of Precambrian age, are a series of gneisses and form a part of a great area of what are known as the Kisseynew gneisses. The Sherritt is the only known economic base-metal deposit to occur within the Kisseynew series. Extreme metamorphism has produced recrystallization that has imparted a decided igneous-like texture to many of the units. However, the gneisses are predominantly of sedimentary original although the most basic member, a hornblendegarnet gneiss, is considered to be an altered basic flow. Figure 1 illustrates the intricately folded structure and the succession of roe types. The footwall enclosing members are of sedimentary origin and represent quartzite and arkosic and greywacke derivatives. The contact footwall member is gneissic quartzite, a medium to coarse grained rock composed mainly of quartz with minor altered feldspar (orthoclase and plagioclase), muscovite, chloritized biotite, and magnetite. Most phases of this unit show varying degrees of granitization.

Jan 1, 1949

By Julie Hunt

Rimfire Minerals Corporation: early stage precious metal exploration specialists with discovery opportunities in partnership with major and mid-tier gold producers or prominent junior exploration firms. Mike Roberts, Senior Geologist

May 1, 2006

The Daly-Judge Tunnel, begun in 1887 to drain mine workings, is now a source of potable water for the Municipality of Park City. The water is exceptionally clean; however, when roof falls occur, suspended solids levels become too high and water from the tunnel cannot be used in the treatment plant. In 2001, the tunnel was inspected and rehabilitated to ensure that the water supply for the 2002 Winter Olympic Games would be uninterrupted. Twenty-five timber tunnel sets were removed, and 86 steel sets were installed. Timber lagging was installed or replaced over about 230 m (750 ft) of tunnel length.

Jan 1, 2006

Flotation works very well for particles that are typically in the range 20 to 150 µmin diameter, for base metal ores. In this range, it is possible to get quite high recoveries in conventional flotation machines. Outside this range, the recoveries decline progressively, whether it be with the very fine or the coarse end of the size spectrum. In this paper, the reasons for the drop-off in recovery are briefly reviewed, together with strategies for future work. Recent progress in the author's laboratory will be described. These include the Concorde Cell, which takes advantage of the high dissipation rates in the shock wave created when a gas-liquid mixture reaches supersonic velocities. The environment thus created is very beneficial for the flotation of ultrafines. For coarse particles, the reasons for the drop-off in recovery can be related to the highly turbulent nature of the pulp in a conventional flotation cell. To improve recovery, it is necessary to find a way of bringing particles and bubbles into contact in a quiescent environment. A new process for coarse particle flotation will be described, in which a fluidized bed is created in the flotation cell. The flow conditions are very gentle, and the high solids concentration leads to rapid rates of capture of the particles. Experimental results are presented. It is apparent that the maximum floatable size for coal and minerals can be increased by a factor often over the limits found in current practice. Advances

Jan 1, 2009

By G. M. Hutt

Introduction The major development of industrial minerals in Manitoba has been in building materials. 'The building-stone industry is developed far beyond the needs of the Province, and the well known Tyndall limestone is marketed over a wide area throughout the other provinces to Canada. Similarly, gypsum and gypsum products are produced in excess of local requirements and are exported to adjacent provinces. The crushed-stone, sand and gravel, limestone, and lime industries are sufficiently developed to supply the needs of the Province and, notably in the case of lime and lime-stone, there is a surplus for export to the adjacent provinces and to the United States. The manufacture of common brick is well established, but for face-brick and other clay products the Province is dependent largely on importations. Production of silica-sand will increase as Canadian markets become available through recognition of the utility value of the Black Island sand as foundry-sand and for other purposes. There is some possibility of the export of feldspar, of lithium ore and concentrates, and perhaps of salt. A considerable part of the Province has not been seriously prospected for industrial minerals and it may be expected that, as time goes on, other deposits of non-metallic minerals will be discovered and opened up, especially as the prairie provinces become more industrialized. At the present time, there is some activity in the southern part of the Province based on gas and oil indications. Whatever may be the outcome of this work, it should yield valuable information concerning the geological structure of the area.

Jan 1, 1934

By Jim Excell, Jim Rothwell, Mike Rylati

"LocationThe Ekati Diamond mine is located at Lac de Gras, Northwest Territories.Brief Description of OperationBHP Diamonds Inc. has developed Canada's first diamond mine in the Northwest Territories (NWT), Canada. BHP Diamonds Inc. is part of the BHP World Minerals Division ofBHP Minerals. The project is a joint venture between manager and operator BHP (51%) and the Blackwater Group (49%). The Blackwater Group comprises Dia Met Minerals Limited, Charles Fipke and Stewart Blusson.Production at the NWT diamonds project began in October with the mine officially opened October 14, 1998. The project is situated on an 853 000 acre claim block located in the Lac de Gras region of the NWT. It is about 300 km northeast of Yellowknife and 100 km south of the Arctic Circle. The seasonal winter ice road to the Echo Bay Lupin mine passes along the eastern margin of the project area. This allows road access each year from mid-January to mid-April. For the remainder of the year, the project is accessible only by air.HistoryIn 1980, Charles Fipke traced indicator minerals east from the Mackenzie River area. He discovered indicator minerals in the Lac de Gras area and staked mineral claims in 1989. A joint venture was formed between BHP and Dia Met in 1990, and in 1991, the first diamonds in the NWT were discovered at Point Lake by BHP and Dia Met. This initiated the largest staking rush in Canadian history. The joint venture launched an aggressive exploration program.Koala, Fox, and Leslie were identified in 1992 as potentially economic pipes.As soon as the project's potential was established, it was recognized that an enormous amount of work had to be completed in several areas before a mine could be developed, namely: technical evaluation of the resources; environmental and socio-economic evaluation to procure the necessary permits for the development; and engineering design to optimize mining and processing of the resource and to comply with specific environmental requirements."

Jan 1, 2000

By R. E. Johnson

Seventy years after the start of the Industrial Revolution in Great Britain, as reckoned from Arkwright's water frame patented in 1769, there was a significant development of the metallurgical industry in Virginia. In Britain, crucible steel had been rediscovered by Benjamin Huntsman in 17~0, and this made spring and tool steel more generally available. The metal-turning, screw-cutting lathe, including the basic principles recognized in today's engine lathe, was developed by Henry Maudslay about 1797. Wrought iron, as manufactured by Henry Cort's process patented in 1784, was readily available. Richard Trevithick's highpressure steam locomotive had met its test on the Pennydarren tramroad in 1804, and George Stephenson had built his famous Rocket, along with several other locomotives, at Newcastle around 1828. Puddling furnaces and a rolling mill had been placed in operation at the Tredegar Iron Works in Glyn Sirhowy, Monmouthshire, Wales, in 1807. In the United States, expanding commerce and a growing population resulted in continuing development from the Chesapeake to Virginia's Blue Ridge, and this demanded improved means of transportation. Ore deposits rich in hematite had been found in Virginia's Piedmont during the Colonial period, and a number of blast furnaces now dotted that area. The products of these operations were mostly pots, kettles, stove parts and like items for local trade. The James River and Kanawha Canal was incorporated in January 1785. Its eastern leg, winding along the slope of the high bluffs overlooking the river, was completed about 1800. About two dozen railroads were chartered in Virginia between 1830 and 1837. With expanding population and steady industrial development came a need for metallurgical products. Throughout the eastern United States, numerous metallurgical enterprises sprang up, and many of these flourished. The purpose of this article is to outline the development of one Southern metallurgical company, the Tredegar Iron Works, which was to have a significant impact on the industrial development of Virginia and the fighting of the American Civil War. Although the Tredegar Iron Works no longer exists, remnants of the early operations have been restored, and the current status of the site is also presented.

Jan 1, 1999

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By W. C. Whittaker

COMPLETED in November, 1943, at a cost of over $1,500,000, Elk River colliery of the Crow's Nest Pass Coal Company, Limited, has been laid out and equipped for an ultimate annual production of 1,000,000 tons and replaces the recently closed Coal Creek plant, which has been operated by the Company for the past forty-five years. The project has involved the opening of mines in three seams, the construction of a complete set of colliery buildings, including a modern preparation plant of 360 tons per hour capacity, and the laying out of the necessary yard tracks and spur connecting the new development with the Company-owned Morrissey, Fernie and Michel railway, which, in turn, connects with the Canadian Pacific railway at Fernie. The colliery is three and a half miles east of Fernie, B.C., near the southern end of the Crow's Nest coal field, which contains the largest and most important body of coal in the Province of British Columbia. The coal-bearing horizon is the Kootenay formation, present in the form of a syncline covering an area of 230 square miles. Most of the coal seams occur in the lower 2,000 feet of the formation, the covering beds being largely coarse sandstones and conglomerates of great thickness, the presence of which accounts largely for the preservation of the coal measures. James McEvoy, in the report of the Geological Survey of Canada for the year 1900, states that the basin appears to contain a fairly constant coal content of nearly 172 feet in 23 seams of a thickness of one foot or over. Coal has been mined in the Fernie district since 1897 and the first shipments were made from Coal Creek colliery in the following year, over the then newly constructed British Columbia Southern railway. Since that time, a total of over 16,000,000 tons of coal has been produced, an average of 350,000 tons per year. The7ears of peak production were 1910, 1912, and 1913, with an all-time high of 924,000 tons in 1913. The lowest output in the history of Coal Creek was that for the year 1933, when only 60,340 tons were produced, the colliery being closed for some months. Present production from Elk River colliery averages 1,150 tons per day, the output being considerably less than it could be were sufficient man-power available.

Jan 1, 1944

By S. C. Tadolini, J. M. Goris, J. L. Gallagher

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines (USBM), researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road entries in a western U.S. coal mine. With the cooperation of industry, methods were developed to install and evaluate cable supports in a tailgate area using traditional resin cartridges. The cable-bolted areas successfully maintained roof support throughout the developed entries. Cable supports have replaced wood cribbing as secondary support in the bleeder entry system and have minimized or eliminated the use of cribbing in the longwall tailgate entries. This paper describes the theory, application, and advantages of cable supports and presents some mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1999