Search Documents

By Fathi Habashi, Ernesto Bourricaudy, Fouad Kamaleddine

Ilmenite occurs in black sand at the mouth of great rivers as in India, or as massive deposits like in Quebec Province in Canada. It is unsuitable for processing into pigment or for metal production because of its high iron content and its low grade. Pyrometallurgical and hydrometallurgical methods have been developed to cope with this problem which resulted in the production of two commercial products that became known as synthetic rutile and Sorelslag. Attempts are also underway to produce TiO2 pigment directly from ilmenite. This report presents a newly developed process called the Magpie process, which enables the production of high-grade synthetic rutile (over 95% TiO2) from low grade ilmenite (10-12% TiO2). Naturally, if such process is applied for low-grade ore it can be applied with advantage to high grade material as well.

Jan 1, 2014

By M. Pötsch, W. Schubert

"The kinematic analysis of rock blocks is one part of a block stability assessment. It provides information about a block’s movability, i.e. if a block can detach from the adjacent rock mass and move towards the free space. This paper introduces an analytical method for the analysis of pure rotations of arbitrary finite polyhedral blocks. It enables the engineer to judge a block’s rotatability about a corner or an edge. The method is presented using a graphical and computational method. The application of the method is illustrated with an example. INTRODUCTIONThe kinematic analysis of rock blocks deals with the determination of the movability of blocks. Established methods typically cover: (a) translational motion (John 1968, Markland 1972, Londe et al. 1969, 1970, Goodman & Shi 1985, Warburton 1981) and (b) the specific rotational cases Toppling (Goodman & Bray 1977) and Slumping (Kieffer 1998). Mauldon & Goodman (1990, 1996) and Tonon (1998) introduced rotational kinematic analyses for three-joint pyramids and tetrahedral blocks extending Goodman & Shi’s block theory.All mentioned methods are subject to assumptions that limit the applicability to engineering problems. For example, the kinematic test of daylighting joints or intersections inherently assumes a finite block, which only can be proved by the finiteness theorem (Goodman & Shi 1985). Daylighting of an intersection or plane is not a sufficient condition for removability. Goodman & Shi’s and Warburton’s methods are limited to translational block motion. The methods for block rotations so far address tetrahedral blocks only. They also address only pure rotational modes and neglect the general motion of a rigid body. This paper introduces an analytical method for the analysis of the kinematic rotatability of finite rock blocks. It extends Mauldon's and Tonon's theory of rotatability of tetrahedra to arbitrary polyhedral blocks. A graphical method using the stereographic projection and a computational method are presented."

Jan 1, 2015

By K. Woo

"With ever-increasing global demand for mineral resources, mining companies are considering developing deeper, more complex and lower grade ore bodies. Recent years have seen the transition from surface to underground mass mining operations to access deeper resources, with mass mining methods such as block and panel caving being favoured due to the tonnages and economics achievable when dealing with lower grade ore. However, the rock engineering interactions involved with such plans are complex and challenging given the significant disturbance caused to the surface environment. If not properly accounted for, the unexpected propagation of a cave breaking through to surface or the differential surface displacements otherwise produced may threaten the safety and integrity of overlying mine and civil infrastructure.This paper reports the findings of a comprehensive research programme focussed on investigating and integrating new developments in remote sensing characterization and monitoring technologies with state-of-the-art numerical modelling to better manage the challenges and geo-risk associated with the transitioning from open pit to underground mass mining. Procedures were developed to integrate discrete fracture networks (DFN) into finite-element/discrete-element analyses to simulate the influence of rock mass fabric on cave propagation and the evolution of caving-induced surface subsidence and step-path failure of large open pit slopes through the progressive failure of rock bridges. The results clearly showed that caving-induced surface deformations tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Although parallel investigations of empirical design charts used to predict caving-induced deformations were found to be moderately sufficient for assessing the extent of macro deformations directly above the undercut (i.e. caving collapse features), numerical modelling was found to provide the only means to confidently estimate the lateral extent of smaller strain subsidence.These results were further supported by the use of high-resolution synthetic aperture radar (SAR) data to monitor the ground deformations associated with block caving production, and to use these to calibrate and constrain a series of predictive 3-D numerical models focussed on Rio Tinto's Palabora mine in South Africa. The InSAR data was obtained from Canada’s recently launched RADARSAT-2. The close fit achieved between the predictive 3-D numerical model and InSAR monitoring data demonstrates the significant value of InSAR calibrated 3-D numerical models applied to subsidence prediction.Collectively, the results from this research programme have helped to further the characterization, assessment and understanding of mass mining-induced subsidence, and its evolution, by addressing existing limitations in the use of empirical and numerical design methods. The limitations and uncertainty arising from mine site data were detailed, specifically the representation of mine geology, rock mass properties, in-situ stresses and cave propagation, together with means to constrain these inputs and calibrate sophisticated 3-D numerical models through back analysis and integration with high resolution monitoring data."

Jan 1, 2015

By A. Dolatmoradi

Nanocrystalline structure formations produced by severe plastic deformation in Fe-0.15C with initial ferritic-pearlitic and IF steel with ferritic microstructures have been studied through microstructural observation and microhardness measurements. It was found that the nanocrystalline region first forms near the surface of samples due to localized severe deformation. It was also observed that the nanocrystallization rate of Fe-0.15C and IF steels and the deformed layer thickness in these two materials are different with similar milling conditions. The crystallite size and structural evolution of the samples during milling was studied by employing XRD and SEM.

Jan 1, 2010

By A. Mykytiuk, I. E. Puddington, W. D. Macleod, F. W. Meadus

"A laboratory-scale continuous procedure for the up-grading of naturally occurring tin ores, based on the principle of spherical agglomeration, is described. High recoveries are indicated. A proposed second stage suggests useful fractionation steps.IntroductionA LABORATORY-SCALE batch process for the upgrading of a tin ore using the principles of spherical agglomeration has already been described (1). This procedure consisted of milling, for about an hour, a precrushed ore with at least 200 per cent water, 0.2 per cent of a reagent such as tall oil (to render the de-sired ore particles hydrophobic) and about 3 per cent of a viscous petroleum oil. The feed material passed an 8-mesh Tyler sieve, and the percentages of re-agents are based on the dry weight of the feed. Du-ring the grinding, the hydrophobic particles transfer into the oil phase to produce coherent semi-solid bodies while the gangue stays preferentially in the aqueous phase. The concentrate can be separated from the gangue easily by a mechanical operation. Using an ore containing about 0.3 -0.5 per cent tin, grades of from 1.5 to 7.0 per cent were obtained by varying the pH of the system. Recoveries fell from about 80 per cent to as low as 50 per cent as the grade in-creased."

Jan 1, 1966

By J. Yue

The particle breakage kinetics, product size and size distribution, as well as grinding limit for quartz suspensions in a horizontal stirred mill are investigated. Results of grinding studies on quartz suspensions in a horizontal stirred mill confirm "first-order" particle breakage rates. A comparison of equation fits reveal that the product size distribution from stirred mill is best represented by the Rosin-Rammler equation when compared to the Gaudin-Shuhmann equation, but results fit poorly as particle size below five microns. A method of determining breakage rates versus particle size is demonstrated which shows that the 10% top size fraction is most appropriate for the determination of specific breakage rates. The method is used to demonstrate the relationship between particle breakage rate and particle size. As the feed particle size becomes smaller, the size reduction ratio decreases and approaches a grinding limit which depends on the effective stresses created in the mill.

May 1, 2004

By Ron Jessulat

"IntroductionBrunswick Mining and Smelting Corp. Ltd. is a IO 500 tid base metal producer. Development is carried out by Jarvis Clark MJM-21 3-boom development jumbos, using Tamrock E400, 410 and 550 pneumatic drills. Typical drift size is 13 ft by 18 ft with a 12-ft advance per round. Blast holes are 1 ½ in. in diameter while reamed holes are 3 in. in diameter. AN/FO is the principal blasting agent, being loaded by C-I-L model60R intermediate loader. The detonators are NONELS and DETINELS. Sulphide dust explosions occur during blasting when dusts from certain minerals such as pyrite and pyrrhotite are ignited by name from the detonating shots. The result is a secondary unwanted explosion with a characteristic shock wave and name front that are very destructive to mine services such as ventilation ducting, electrical cable, and ventilation control doors.A typical reaction in the Brunswick orebody occurs according to the chemical formula:4FeS 2 + IIOs-2Fe2O3 + 8SO2 + 3458--(Enright , 1988)The hematite (FeO3) is deposited as a red dust in the blast area while the toxic sulphur dioxide gas (S00 contaminates the underground workings . The presence of S02 gas disrupts production until it is purged from the area by the mine ventilation system or dissipates slowly in those areas where the vent ducting has been melted by the name front or torn down by the shock wave.Sulphide dust explosions exact a high economic toll. Direct costs in damaged materials and wages are probably exceeded by the value of lost production and disruption to the mining cycle. In addition, the health and safety concerns associated with sulphide dust explosions cannot be ignored."

Jan 1, 1993

By Alex Luyima, Michael Moats

"In the present work, the oxidation of manganous and chloride ions on a mixed metal oxide (MMO) anode from a 40 ºC electrolyte containing 160 g/L sulfuric acid (H2SO4) with various concentrations of Mn2+ and Cl- was studied using cyclic voltammetry. These results indicated that Mn2+ concentration does not affect Cl2 evolution on a non-MnO2 coated MMO anode. However once MnO2 deposits on the MMO anode, Cl2 evolution is inhibited. The effects of manganous concentration and chloride concentration on the amount of MnO2 deposited in one hour were also evaluated. Cl- concentration did not affect the amount of MnO2 generated. Increasing Mn2+ concentration resulted in an increase in the amount of MnO2 deposited.INTRODUCTIONThe electrolytic recovery of zinc (Zn) is a well-known process and is estimated to produce approximately nine million tons of Zn per year worldwide (Recendiz, Nava, Lartundo-Rojas, Almaguer, & Gonzaleza, 2009). The Zn produced by this process is of high purity and has a wide range of applications, such as galvanizing (car body parts, pipes, metal wires, etc.), sacrificial anodes in offshore industries, casting alloys, alloying of brass, primary and secondary battery industries, etc.The electrochemical production of Zn employs aluminum cathodes and lead-silver anodes (Pb- Ag) (Recendiz et al., 2009). The Zn containing mineral (ZnS) is usually associated with other elements such as Mn, Mg, Ca, Cd, Cu, Cl, Fe, F, Co, Ni, Al, As, Sb, Si, Sn, Ge, Hg etc. (Nijjer, 2000). After processing of ZnS concentrates, the electrolyte obtained still contains residual metallic and non-metal impurities. Some of these impurities can impact the corrosion rate of Pb-Ag anodes."

Jan 1, 2016

By A. Welty, T. Garn, K. Lyon, B. Jakovljevic, R. S. Herbst, M. Greenhalgh, Cytec Solvay Group

"Industrial rare earth separation processes utilize PC88A, a phosphonic acid ligand, for solvent extraction separations. The separation factors of the individual rare earths, the equipment requirements, and chemical usage for these flowsheets are well characterized. Alternative ligands such as Cyanex® 572 and the associated flowsheets are being investigated at the pilot scale level to determine if significant enhancements to the current separation processes can be realized. These enhancements could be defined as higher separation factors, reduced stage requirements, or reduced chemical consumption. Any of these enhancements can significantly affect the costs associated with these challenging separation proccesses.A mid/heavy rare earth element (REE) separations flowsheet was developed and tested for each ligand in a 30 stage mixer-settler circuit to compare the separation performance of PC88A and Cyanex® 572. The ligand-metal complex strength of Cyanex® 572 provides efficient extraction of REE while significantly reducing the strip acid requirements. Reductions in chemical consumption have a significant impact on process economics for REE separations. Partitioning results summarized Table 1 indicate that Cyanex® 572 offers the same separation performance as PC88A while reducing acid consumption by 30% in the strip section for the mid/heavy REE separation."

Jan 1, 2016

By Michele L. Kimble

A fast-flow reactor mass spectrometer has been utilized to investigate the reactions of gas-phase gold cluster anions with CO and oxygen. Addition of CO to Aun - produces species of the form Au(CO)m -, where m = 2-5. However, CO does not bind to Au2 - or Au3 -. With oxygen addition in the cluster source, gold oxide species with both molecular and atomized oxygen are produced. The addition of carbon monoxide to these preoxidized gold cluster anions reveals that select species with 1, 2, and 3 gold atoms participate in the oxidation reaction to produce CO2. Bimolecular rate constants for the reactions between these species and CO are also discussed.

Oct 1, 2003

By Donald Lindell

Safety Share ?Dad receives fryer for Christmas 2009 and makes delicious sweet potato fries ?When the oil fryer was pushed back on the stove for cooling, the back edge comes into contact with the stove top controls, unknowingly activating the cooking element, family leaves kitchen. ?Faint smell of smoke from the melting plastic alerted the family; teenager arrives first and pulls the fryer forward causing oil to spill onto hot stove and burst into flames that reach the microwave ?Teen runs for sink to grab pan of water but is stopped by Dad ?Dad opens refrigerator, grabs baking soda and pours it on fire, extinguishing flames Lessons 1.DO NOT USE WATER ON GREASE FIRE 2.Where is the baking soda in your kitchen?

May 1, 2010

By K. Tsuchihashi, A. Kishimoto, T. Uda, Y. Kado, S. Maruyama

We recently proposed a continuous production process for titanium metal with some experimental results. In the process, titanium tetrachloride is reduced by Mg in the presences of Bi to form a Bi-Ti alloy at 900ºC. At this temperature, the obtained alloy is liquid and allows for the continuous removal of product and heat from the reaction vessel. The obtained Bi-Ti alloy was vacuum-distilled at 1000ºC for 24 hr, and 98 at % (92 wt %) titanium, which was easily crashed to powder, was obtained. Bi solvent was selected because of the highest titanium solubility at 900ºC and the moderate vapor pressure among the candidate metals (Bi, Sn, Pb, Zn, and Sb).

Jan 1, 2014

By Christopher A. Jacobs

Project managers aim to maximise the NPV of their projects, but don't always appreciate the relationship between mine throughput, project value and the discount rate being used to evaluate their projects. Rate of production or throughput is perhaps one of the most crucial decisions a project manager must make, but if this choice is made arbitrarily, much effort may be spent on a feasibility study that does not optimise project value. The timing of the study in relation to the stage of exploration is examined and simple techniques are presented that project engineers and managers can use to home in on a production rate which will give their project the greatest chance of success.

May 1, 2006

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By Z. Zhao, B. Li

"Fractures are the key channels for fluid flow and mass transport in fractured rocks of low/negligible matrix permeability. In single rock fractures, surface roughness causes fluid flow in tortuous paths, and reduces the overall fracture conductance. A number of empirical models have been proposed to relate the reduced hydraulic aperture to the mechanical aperture due to surface roughness, which were revisited and compared. Using two of those relationships between hydraulic apertures and mechanical apertures, we studied the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks. The results show that fracture roughness can affect the flow rates and residence time to varying extent, mainly depending on the empirical models between hydraulic apertures and mechanical apertures. However, fracture roughness has negligible influences on the general patterns of fluid flow (channeling) and solute migration (e.g., travel paths and shape of breakthrough curves). This is because the connectivity of a fracture network is mainly determined by other geometrical parameters (fracture positions, orientations, and lengths), rather than roughness or apertures. INTRODUCTIONIn fractured crystalline rocks of low or negligible matrix permeability, fluid flow and contaminant migration mainly occur within the connected fractures. An understanding of fluid flow and contaminant migration in fractured rocks is a crucial issue in many deep underground projects, e.g. underground repositories for radioactive waste, CO2 sequestration, enhanced geothermal systems, oil and gas production, etc. Rock fractures are typically rough-walled, and surface roughness appears to have first order control on the mechanical and hydraulic behavior of single rock fractures (Boutt et al., 2006).It is well known that the mechanical aperture of a rock fracture is usually larger than its hydraulic aperture, due to fracture surface roughness (Tsang and Witherspoon, 1983). However, for naturally fractured rocks including numerous discontinuities, the effects of this reduced hydraulic aperture in local fractures on macroscopic fluid flow and solute transport in complex fracture systems still remain unclear. Many previous studies assumed identical hydraulic and mechanical apertures in discrete fracture network models for simplicity (Min et al., 2004; Zhao et al., 2011). Therefore, the main objective of this study is to evaluate the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks, by employing the empirical models that relate the hydraulic aperture to the mechanical aperture."

Jan 1, 2015

By I. Protkova

Versa Power Systems solid oxide fuel cell (SOFC) stacks operate at intermediate temperatures 700 ? 800 °C allowing the use of metallic interconnects. Thermal expansion good matching with other stack components and cost restriction led to selecting ferritic stainless steels as interconnect material. Analytical tools and techniques were developed to understand the ferritic stainless steel behavior at high temperature while exposed to dual environment. Analytical tools such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) have provided valuable information towards describing interconnect degradation in a variety of testing conditions. Several examples are presented to demonstrate interconnect oxidation and its relation with SOFC testing results.

Jan 1, 2005

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By O. A. Ojo, O. A. Idowu, N. P. Wikstrom, M. C. Chaturvedi

Transient Liquid Phase Bonding (TLP) of a Nickel base superalloy, Inconel 738, was performed to study the influence of holding time, filler gap size, and temperature on the joint microstructure. Insufficient holding time for complete isothermal solidification of liquated insert caused formation of eutectic-type microconstituents along the joint centerline region. An increase in the eutectic thickness with increase in initial filler gap size was observed in joints prepared at a constant temperature and holding time. In agreement with prediction by conventional TLP diffusion models, an increase in bonding temperature for a constant gap size, resulted in decrease in the time, tf, required to form a eutectic-free joint by complete isothermal solidification. However, a significant deviation from these models was observed in specimens bonded at and above l 175°C. A reduction in isothermal solidification rate with increased temperature was observed in these specimens, such that a eutectic-free joint could not be achieved by holding for a time period that produced complete isothermal solidification at lower temperatures. Considerable enrichment of the liquated insert with base metal alloying elements at higher temperatures is suggested to be an important factor contributing to the observed departure from conventional TLP prediction.

Jan 1, 2006

By T. Rahimzadeh, C. W. Trueman, S. Farzaneh, S. V. Hoa, I. Abdalla

This paper presents the shielding effectiveness (SE) of woven continuous carbon/epoxy composite materials. The theoretical and physical concepts behind the experimental results are demonstrated in details. The influence of frequency, the overlapping angle between overlapped layers and the number of overlapped layers upon the EMI shielding of composite sheets are discussed. In this work, in particular, the epoxy layers are considered as dielectric apertures of the conducting carbon fiber slab for the interpretation of the experimental results. The experimental results, using ASTM standard D4935-89, indicate that the SE can reach values greater than 90 dB above 500 MHz.

Jan 1, 2006

By A. M. Reyes

Flow field hydrodynamics of serpentine flow channels was investigated numerically using computational fluid dynamics (CFD). The velocity profile simulated by the CFD model was evaluated with respect to experimental results from the literature. Rectangular and tapered flow channels were compared with respect to mixing and water management capabilities, and pressure drop. The CFD model was further developed to account for electrochemical reaction on the cathode side to determine which channel configuration was most effective in reactant conversion. The velocity profile differences between the channels were found to impact reactant conversion, as the rectangular channel had the highest conversion. With respect to water management, although the tapered channel was found to have a higher overall pressure drop, the rectangular channel was found to have higher shear and pressure forces acting on simulated liquid water droplets in the channel.

Jan 1, 2005