Search Documents

By A. L. Irwin

THE disposal of tailing or waste material, which is generally a very large proportion of the ore treated, is a major problem in the location and operation of any concentrating enterprise and especially so where the life of the operation is expected to continue for many years. Many factors need to be taken into consideration in the selection of a tailing site, chief among which are economical handling of the material, subsequent re-treatment of the tailing, and precaution against stream pollution by waste water. The final location of many mill sites bas been governed largely by the selection of a sui table area for tailing storage. The Sullivan concentrator of the Consolidated Mining and Smelting Company is situated about three miles from the Sullivan mine at Kimberley, B.C., and one of the deciding factors in its location at this distance from the mine was the availability of a suitable area in which tailing could be deposited. In view of the indicated long life of the property, a far-sighted policy bad to be adopted in the matter of tailing storage, for not only would it be necessary to accumulate a huge tonnage of finely ground material, but also reclamation for iron recovery at some future date bad to be considered. Some idea of the extent of the problem may be grasped when it is noted that, by the end of 1938, over 18,000,000 tons of tailing bad been impounded in an area of some 200 acres.

Jan 1, 1939

By J. C. Li, Y. Zou, L. He

"The effect of rock joints is significant in characterizing dynamic behaviors of discontinuous rock masses. To reveal the relation between the transmission coefficient and the contact situation of the joint surface, an experimental study on stress wave propagation across an artificial rock joint was carried out using a modified Split Hopkinson Pressure Bar (SHPB) apparatus. All the bars and specimens were norite cored from the same site, and one surface of the specimen which contacted to the transmitted bar was sawn with a number of notches to simulate the artificial rough joint. According to a wave separation method, two strain gauges were mounted on each pressure bar at a specific spacing, then the incident, reflected and transmitted waves across the joints were obtained from the test data. It was found that the contact situation of the rock joint surface makes a different on the wave propagation. Finally comparisons of the transmission coefficients with different contact area ratios and different joint thicknesses were made respectively. The results show the effects of contact area ratio and thickness of joints on wave transmission.INTRODUCTIONJoints affect the dynamic mechanical behaviors of the rock masses significantly. When propagates across the rock masses, wave usually attenuates in amplitude and frequency due to the presence of the joint as a discontinuous interface in the rock masses. Rock joints are the main factor that affects the behaviors and properties of rock masses. Many researchers have focused on the mechanical properties of rock joints under quasi-static conditions. Nowadays, the effect of joint dynamic properties on wave propagation across rock masses is gradually taken into account in theoretical and numerical studies.The effective contact area, joint roughness, and properties of the asperities and filling materials have been found to influence the normal stiffness of joints (Bandis et al. 1983). As suggested by the International Society for Rock Mechanics (ISRM), the roughness of the discontinuities can be generally characterized by large-scale “waviness” and small-scale “unevenness” (Brown 1981). Many researchers focused on the roughness of rock joints that affects the mechanical properties of rock masses and wave propagation. For example, Brown and Scholz (1985, 1986) presented theoretically and verified experimentally a closure model of contact between two random nominally flat elastic surfaces, which showed that the joint closure property depended both on the surface topography and material properties. Pyrak-Nolte et al. (1997) presented the quantitative aperture data for three-dimensional interconnected fracture networks, which were imbedded in intact opaque rock samples several centimeters in length, using x-ray computerized tomographic (CT) imaging. Fardin et al. (2001) systematically investigated the effect of scale on the surface roughness of rock joints and concluded that samples should be equal to or larger than the stationary limit for surface roughness to be accurately characterized on a laboratory scale or in the field. Zhao et al. (2006) conducted excellent ultrasonic tests across intact cement mortar specimens, singlefracture specimens, and two-fracture specimens."

Jan 1, 2015

By M Reza Afshar

In this work a mathematical model was developed to study the effect of electromagnetic force on the magnesium melt containing nonmetallic inclusion in an electrical isolated channel. The electromagnetic force exerted on the inclusion induced by DC current field was calculated. A three dimensional turbulent flow equations were solved numerically to compute the velocity field within the channel. On the basis of computed velocity and magnetic fields, the trajectories of inclusions were calculated using the equations of motion for inclusions. Parametric studies were carried out to evaluate the effect of various parameters such as current density, channel diameter and particle density on the removal efficiency of inclusions from magnesium melts.

Jan 1, 2004

By D. F. Sangster, P. J. Hood, G. A. Gross

"Some results are presented of an integrated geological and geophysical study of Precambrian magnetite-quartz iron-formation in the Kapiko Iron Range north of Nakina, Ontario. Detailed geological and topographical mapping was carried out in conjunction with detailed geophysical investigations such as vertical magnetic field, vertical magnetic gradient, hammer seismic, horizontal-loop electromagnetic and magnetic susceptibility surveys. In addition, oriented drill cores were obtained for magnetic polarization studies.Vertical-force magnetic anomalies within individual rock units showed a strong positive correlation with topographic relief. Moreover, magnetic intensity was found not to be quantitatively proportional to the magnetite content in the rocks, due to the presence of high remanent magnetization of the magnetite. Also, the remanent polarization direction was sub parallel to the plunge of the fold structure and mineral lineation in associated rocks.Vertical magnetic gradient measurements were found to be more accurate in locating buried contacts between magnetite-quartz iron-formation and country rock than the vertical magnetic force data.An in-situ magnetic susceptibility meter was used to measure the magnetite content of iron-formation, and the measurements were subsequently compared with vertical-force magnetic results.The results of the EM survey were inconclusive; some magnetite-rich zones produced anomalies in the out-of-phase component. whereas others did not. The reasons for such inconsistencies are not yet apparent.Longitudinal seismic wave velocities measured parallel to the bedding in magnetite-quartz iron-formation ranged from 10,600 ft/sec. to 14,500 ft/sec. The seismic velocity appears to increase with an increase in deformation of the rocks."

Jan 1, 1966

The dissolution of chalcopyrite has received a significant amount of attention. The predominant paradigm of investigation is that its rate of dissolution is limited or passivated by a surface coating or film of material. The common candidates for such a passivating coating are numerous: polysulfide coating, metal deficient layers, copper sulfide coating, bornite layers, jarosite precipitates, and elemental sulfur films. While this line of explanation, that is, the explanation based on passivation, seems to have won some form of consensus with researchers, there is another explanation for the results that can account for all the results observed. Crundwell (1988) proposed that the solid state properties of chalcopyrite, in particular, the semiconducting properties, are responsible for the observed behaviour of chalcopyrite. The purpose of this paper is to outline the semiconductor mechanism of dissolution, and to show how this mechanism accounts for all the observed phenomena recently reported in the literature. The paper outlines the semiconductor mechanism of dissolution, shows how this mechanism accounts for the dissolution

Jan 1, 2014

By A. Singh

Deformation structures after tensile and compression tests on Mg926Zn64Y alloy extruded at 250°C and 400°C are studied, in as-extruded and heat treated conditions. The icosahedral phase particles stimulate recrystallization during extrusion, resulting in fine grain size. Tensile and compression tests at room temperature show comparable yield strength, with a yield asymmetry ratio up to 0.98. c-type dislocations are observed in the grains near the submicron size icosahedral phase particles. The source of these dislocations is believed to be dissociation of <c+a> type non-basal dislocations. No dislocation pile-ups on icosahedral phase particles are found. {10 1 2} type twinning occurs in compression.

Jan 1, 2006

By R. Kong, X. W. Zhang

"High pressure (up to 50 MPa) isotropic compression tests were performed on marble, gneiss and sandstone specimens, of which represents the typical rocks, to investigate isotropic compression deformation characterization at room temperature. Experimental data with respect to volume change in loading and unloading are presented. An apparent volume change inflection point (sensitive stress) was observed at a lower pressure range for porous sandstone, indicating that the elastic-plastic behaviour arising in the isotropic compression stage, but for tight crystalline rock, the sensitive stress is much higher, not probed prior to 50 MPa. The irrecoverable volumetric strain in the unloading can be seen for sandstone as well. The anisotropic deformation was discussed in terms of the axial and radial strain measurement. It was found that essential features of mechanical anisotropy are the irreversible in deformation range. The deformation feature in the isotropic compression tests is a very complex issue due to the factors concerning the stress history, unloading in sampling and in-situ stress. INTRODUCTIONThe isotropic or hydrostatic compression condition that stress is compressive and has the same magnitude for all direction, which is expressed as s1=s2=s3 in principal stress space. A yield locus of soils subjected to the isotropic and anisotropic compression was widely known, for instance Cam Clay model, which forms a closure cap model. However, the similar isotropic compression yield curves for rocks, especially for hard rock, was not established due to the geo-stress in the rock mass is much less than the socalled isotropic yield stress. And hence, the previous experimental studies on the hard rock have been made tend to on the stress-strain-strength relationship (Handin & Hager, 1957; Edmond & Paterson, 1972; Menéndez et al., 1996). Perhaps the yield curves related to an increasing in the hydrostatic pressure is not forced to construct for hard rocks, undoubtedly, the deformation data in this processing is valuable to assess the bulk module (Fabre & Gustkiewicz, 1997), anisotropy (Niandou et al., 1997), field stress (Hakala et al., 2007). Furthermore, many rocks store much elastic volume strain energy link to the hydrostatic pressure exerted, following a deviator stress applying, to drive the unstable brittle fracture for hard rock. Latter was studied to interpret the incentive of rock burst. However, volume change characteristic in the isotropic compression behaviour have been scarcely studied experimentally to our knowledge, less application related to the fracture in hard rock as well. The mechanical behaviour in the isotropic compression of hard rock is notably affected by the original structure anisotropy, stress history and stress condition before sampling, all of which need reasonably assess. It is also a useful understanding to study isotropic compression that elastic and plastic volume change in the isotropic loading and unloading, and the micro crack evolution throughout it."

Jan 1, 2015

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By A. J. Russell

"This paper investigates why it is critical for a mine to accurately determine thermal rock properties and virgin rock temperatures. Theoretical simulations of deep mining production zones have demonstrated that thermal conductivity (k), virgin rock temperatures and specific heat (cp) significantly impact rock heat predictions which can be the dominant component of a mine’s heat load. Natural variability in these factors showed that realistic errors can have a significant effect on mine heat loads. This can ultimately affect miner safety and introduces risk to the viability and sustainability of a project. INTRODUCTION Accurate heat load determinations are critical to ensure that underground working conditions are maintained within legislated and mine specific parameters to safeguard the safety and productivity of employees. Underpredicting mine heat loads will result in hot underground conditions, which risk the health and safety of employees, reduce the productivity of employees or stop production if legislated temperatures in working areas are exceeded. Overestimating mine heat loads will result in increased capital and operating costs reducing the viability of the project. Over- or under- predicting the heat load for a project will increase the project risk. Heat sources in a mine can broadly be broken into two categories. These two categories are defined by Hemp and Rawlins (2014) as natural and artificial heat sources. Those sources which depend on the size, location and depth of the mining areas are defined as natural heat sources, whereas those heat sources which are a result of the actual mining activities are defined as artificial heat sources. Autocompression, or the conversion of potential energy, to enthalpy is an important consideration when determining the air temperature in the mine and its interaction with natural and artificial heat sources. It is documented by Jones (1985) and Hemp and Rawlins (2014), that the heat flow from rock in deep mines can dominate other heat sources; information from BBE’s archives show that this is between 40% and 60% of the total heat load. They also point out the importance of accurately measuring both the thermal rock properties and virgin rock temperatures (VRTs) for determining and planning the ventilation and refrigeration requirements for a mine. Both of these texts cite multiple methods for calculating the heat-flux and ultimately the heat load for the different working areas in a mine. All of these methods demonstrate that the heat flux and heat load will increase proportionally with increased thermal conductivity (k), specific heat (cp) of the rock or mineral, and VRT depending the area of the mine or mining method."

Jan 1, 2019

By Finch. J. A., C. Perez, J. M. Ortiz, G. Cortes, A. B. Yañiez, F. Coddou, P. Morales, H. Elgueta

A campaign to perform characterization tests in a TankCell®-300 flotation cell installed at Chuquicamata Codelco&apos;s concentrator was conducted. The campaign included integrated gas dispersion measurements (gas velocity radial mapping and single point gas holdup and bubble size) and determination of frother concentration. Cell streams were sampled to assess metallurgical performance at the same time. The experimental program was designed to establish the bubble surface area flux operating range and its effect on performance, and the effect of using longer residence times and of a device designed to enhance mixing in the collection zone (FlowBooster(TM)). The gas dispersion results and their relationship to metallurgical performance are discussed.

Jan 1, 2009

By Mustafa Kumral

Monte ? Carlo simulation is often used to assess the risks associated with uncertain variables in mining operations. The success of Monte-Carlo simulations depends upon reproducing the dependencies among variables to some extent. However, some variables may exhibit different dependency patterns. In these cases, classical techniques for dependency quantification cannot capture dependencies. As an alternative, the copulas allow modeling nonlinear dependencies. Furthermore, any choice of marginal distributions can be used. Especially, for the data, which is sensitive to extreme case such as financial crisis, the copulas arise as a means to reproduce the correlations among variables. In this paper, the copulas are introduced to mining practitioners using Monte-Carlo simulations for risk assessment. Then, a case study is given to show the superiority of the copulas over classical techniques using ModelRisk Software. In conclusion, it was observed that the copulas enhance the quality of Monte-Carlo simulations by capturing variable dependencies.

Aug 1, 2013

By Joseph B. de Hart

Two papers recently published on the subject of mine ventilation: "The Theory of Ventilation," by Douglas Hay. and "The True Effect of Natural Ventilation in Deep Mines," by Robert Clive, form the first and second reports respectively of the committee on the Ventilation of Mines appointed by the Midland Institute of Mining Engineers. The purpose of the present paper is to draw attention to these two papers and the discussion thereon. The theory of ventilation as taught in our schools is based on Atkinson&apos;s formula, which is a variation of Chezy&apos;s formula for the flow of water in pipes. The formula depends on two assumptions : 1. That air is an incompressible fluid within the limits ordinarily encountered, and; 2. That the pressure required to produce ventilation varies as the square of the rate of flow. The Atkinson formula has been assumed to hold good over the entire range of conditions met with in mines.

Jan 1, 1924

By H. Clare Horwood

"In the Little Long Lac-Sturgeon River area of Thunder Bay district, Ontario, most of the known ore deposits occur in fractures, shear zones, and zones of brecciation, in folded sedimentary rocks . In two or three instances, however, deposits occur in Keewatin greenstones and in later granitic rocks of probable Algoman age.The principal regional features in the area are the long narrow bands of Keewatin volcanic rocks and Timiskaming sedimentary formations that extend east from lake Nipigon to Long Lac, a distance of about 65 miles. The belts continue to the east for many miles beyond Long Lac and probably for some distance to the west under the waters of lake Nipigon. They are intruded in places, particularly in the north, by large masses of diorite, granodiorite, and granite. Small intrusive masses of diorite and porphyry also occur in many localities throughout the area.The Little Long Lac-Sturgeon River mining area is the youngest camp in Ontario and has been in production only since 1934.The district is readily accessible from the branch line of the Canadian National railway between Longlac station on the main line and Port Arthur, and from the Trans-Canada highway No. 17. Both these means of communication traverse the area in a general east-west direction parallel with the principal structural trend of the rocks of the region.In the Little Long Lac section discoveries were made by W. W. Smith in 1931 (Hard Rock property) , by T. A. Johnson in 1932 ( Bankfield property) , by T. A. Johnson and T. Oklend in 1932 (Little Long Lac property) , by F. MacLeod and A. Cockshutt in 1933 (MacLeod-Cockshutt property) , and by George and Frank Papineau in 1935 (Hutchison Lake property).In the Sturgeon River section discoveries were made by Powers and Silam in 1925 (Northern Empire property), T. A. Johnson in 1931 (Dik-Dik property) , and by Russell and James Cryderman in 1935 and 1936 (Sand River and Leitch properties)."

Jan 1, 1954

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By C. Lapointe

"IntroductionTen years ago, when nuclear fission became practical, the element uranium, until then a not very desirable by-.product of the radium industry, became overnight the strategic material par excellence. One of the several important problems that had to be solved at that time was the rapid and precise determination of uranium in ores and concentrates.GeneralThe chemical analysis of uranium ores is a long and difficult business and is complicated by the presence in most ores of a large number of interfering elements. True, much progress has been made, during the past few years, toward simplification of the analytical methods, but the chemical determination still remains the job of a skilled operator. For this reason, the chemical method has been replaced, whenever possible, by a physical determination based on the measurement of the radiations emitted by the elements of the uranium family. There are several types of instruments suitable for these measurements, but of all the radiation detectors known to the physicist, such as ionization chambers, crystal detectors, scintillation, proportional counters, and the like, the Geiger-Mueller counters have proved to be the most satisfactory for routine determinations, because of their simplicity.The Geiger-Mueller counter is a very versatile instrument; it can be constructed to detect any type of radiation, corpuscular -0r electromagnetic. Here, however, we are interested in these counters because of their ability to detect the beta and the gamma radiations, both emitted by some members of the uranium family. The beta radiation is corpuscular, and is composed of fast electrons, while the gamma radiation is electromagnetic."

Jan 1, 1950

By D. Bouchard, J. Langlais, A. Lemieux, N. Andrade

A concerted effort between Akan International Limited and the National Research Council of Canada (NRC) has been initiated to develop a liquid-based slurrymaking process, dubbed SEED (Swirled Enthalpy Equilibration Device) for semi-solid forming. The technology is presently entering the industrial and commercial stages, and will be used by the first customers at the end of 2006. Semi-solid processing of aluminium alloys offers many advantages in fabricating economically near-net-shape parts of superior quality. The SEED process helps to overcome problems experienced with thixocasting and especially the high cost of feedstock. The SEED process involves two main steps: 1) heat extraction to achieve a desired liquid/solid mixture, and 2) drainage of an excess liquid to produce a self-supporting semi-solid slug that is formed under pressure. The heat transfer plays an important role (enthalpy equilibrium) during the manufacture of the semi-solid slurry and its analysis is briefly described. The semisolid material is obtained using different processing times and initial conditions. The impact on the solid fraction distribution and the morphological evolution of the microstructure is presented. The influence of the SEED processing parameters (slurry preparation) and the resulting mechanical properties for the alloy A356 are also reported.

Jan 1, 2006

By Vincent H. Hartung

The process of estimating tailings deposition for a given basin is a relatively tedious process without dedicated software tools. The amount of time required to generate a tailings surface for a given set of conditions tends to limit the number of design alternatives that can be considered for a particular project. Recent innovations in the Surpac Vision mining software include the widely used scripting language TCL (Tool Command Language) that brings with it the ability for non-programmers to extend the software functionality beyond mining applications alone. A software tool was developed using the Surpac Vision scripting language to take advantage of 3D visualization and create a flexible tailings modeling solution. The result is an application that removes much of the drafting overhead required to produce a tailings surface. It provides the means for reviewing alternatives and performing sensitivity analysis with variables such as pond elevation, dam or spigot location and height without a significant increase in overall time for a project.

May 1, 2001

By G. R. Guillet

Salt is restricted to five major beds in south western Ontario, totalling as much as 200 m in thickness. These beds are located at depths ranging from 270 m to 750 m below the surface, fringing Lake Huron and the Detroit River from Windsor to Kincardine, and extending inland as far as London. Manitoulin Island, the Bruce Peninsula and the north part of the Niagara Escarpment form the northeastern rim of the Michigan Basin, a major structural depression in which the salt was deposited 400 million years ago when much of North America was covered by the Silurian sea. Salt is mined underground at Windsor and Goderich; it is also brought to surface as brine through deep wells at Windsor, Samia and Goderich. Artificially- created caverns in salt beds are extensively used for storage of liquid hydrocarbons at Windsor and Samia.

Jan 1, 1984

By L. Xia, B. Hart, J. Nigim, Z. Chen

"Grinding ore is an important step in the flotation process. Not only does grinding reduce particle size and liberate minerals, it also creates conditions for reactions to occur on particle surfaces that can aide or inhibit flotation. There have been numerous studies examining various grinding regiments and the effect on flotation pulp chemistry, including autogenous grinding and using media of variable composition. There have been however, few studies looking at the effect of variability in grinding media size on pulp chemistry and subsequent flotation. This study attempts to link changes in pulp chemistry in response to variations in grinding media size to flotation recovery. It uses probes mounted in the grinding chamber (pH, Eh, DO, and conductivity) to monitor pulp chemistry changes during grinding of a Cu-Zn ore. Surface chemistry analysis by ToF-SIMS was performed on sphalerite from the mill discharge. Activator and depressant species were monitored on the mineral surfaces and their presence was evaluated in the context of variability in pulp chemistry linked to differences in grinding media and its ball size.INTRODUCTIONIt has been widely recognised that not only does grinding reduce particle size and liberate minerals but the grinding environment has a large effect on the flotation of sulphide minerals. This effect is attributed to Eh change, iron hydroxide coating on surfaces, oxygen reduction, precipitation from solution and galvanic coupling (Grano, 2009). As early as 1960, it was reported that after grinding the ores in an iron mill the natural floatability of sphalerite was reduced significantly (Rey and Formanek, 1960). Kocabag and Smith (1985) studied on the industrial circuits showing that the depression of sulphides flotation in a steel mill is possibly due to the coating of iron oxidation products. Peng, Grano, Fornasiero, and Ralston (2003a, 2003b) found that iron contamination from grinding media plays a dominant role in depressing galena and chalcopyrite flotation. Huang, Grano, and Skinner (2006) reported the same observation in the flotation of arsenopyrite."

Jan 1, 2016

By S. J. Buckler

Many metallurgical processes use submerged gas injection to increase the contact area between gas and liquid phases in order to promote faster overall reaction rates. The work presented in this paper is part of an experimental investigation to measure the gas-liquid interfacial area available in bubble plumes within molten metal baths. Measurements of the nitrogen absorption rate during submerged injection into molten iron baths have been used to estimate the interfacial areas of the bubble plumes. A theoretical model was used to predict the superficial nitrogen transfer rate under mixed liquid phase mass transfer -interfacial reaction control. The interfacial area was calculated by dividing the overall nitrogen absorption rate by the superficial rate. Reasonable agreement was obtained between the interfacial areas measured in our laboratory with data from a comparable system reported in the literature. The experimental results were compared with the predictions of three theoretical models and one empirical correlation. The models of Turkdogan (3) and Zhao and Themelis (5) gave the best agreement with our data.

Jan 1, 2004