Search Documents

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By L. Dufourm

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By E. Burdukova

Long-chain primary amines are utilized as collectors in potash ore flotation. Krafft temperature of long-chain amines in brine is about 100 °C, and this makes such amines practically insoluble in brine at room temperature. When dodecylamine, melted at 70 °C and dispersed in hydrochloric acid (or acetic acid) aqueous solution, is added to a KCl-NaCl saturated brine at room temperature, the amine precipitates. The experimental results demonstrate that the precipitating amine hydrochloride particles are selectively abstracted by KCl particles, but not by NaCl particles.

Jan 1, 2009

By William James Kempson

This paper discusses ore handling systems in shafts. These are considered from the loading facility at shaft bottom all the way through to the discharge mechanism in the headframe. These systems will be discussed from the following perspective: i. Intrinsic safety of the systems ii. The efficacy of the systems to perform consistently iii. The maintainability of the systems iv. Overall system cycle times Particular emphasis is placed on the following specific areas: 1. The Shaft Bottom Loading Facilities The various shaft loading systems currently in use are discussed, the selection parameters surrounding these are quantified and the specific selection criteria are outlined. 2. The Various Skip Configurations In this section the various skip configurations in use around the world will be described and the specific design details associated with these will be highlighted. The advantages and disadvantages of these systems will be compared and the overall efficacy of these will be discussed. 3. The effect of the loading and skip configurations on the Load Cycle Times. The overall cycle time which can be achieved by a shaft system is strongly dependant by the speed and efficiency with which the ore can be loaded and transported out of the mine. The potential of the various systems to be optimized will be discussed. The emphasis of this paper is to highlight the lessons which have been learned with respect to ore transport system design and provide a common basis against which these can be compared in future applications.

May 1, 2013

By J. F. Harkom

Introduction The importance of the preservative treatment of mine timbers need scarcely be stressed here. Increasing the life of mine timbers will reduce one of the major costs of mining and also conserve the available timber supply which lies within easy access of the mines. When treated, several species of timber may be used which otherwise could not be considered, owing to their short life. Another feature which should appeal to the mining industry is that wood preservatives are a mine product, and the benefit to be derived from the increased consumption of wood preservatives due to the example set by mine owners is not inconsiderable. Mine timbers may be divided into three classes when considering preservative treatments. (1) Timber obviously not profitable to treat owing to long natural life or short period of time in service. (2) Timber that obviously should receive protection from decay. (3) Timber installed in locations where the length of service required will depend on future developments, so that preservative treatments might or might not prove to be a profitable investment.

Jan 1, 1930

By J .. Carignan, Y. Dembele, J .. Guha, A. Fowler, A. Gobeil

The Barlow Lake stratigraphic section comprises the top of the Gilman Formation, the Blondeau Formation and the three sills of the Cummings Complex. Representative samples were analysed to allow characterization of the chemo-stratigraphic profile and geochemical affinity of the six rock facies found in the section. All the mineralized horizons are associated with sedimentary units. Geochemical signatures associated with the mineralizations are either very weak or very localized and shown by increases in K20 around the mineralizations and Fe203 near them. The mineralizations are stratiform, synvolcanic but resedimented and remobilized by regional metamorphism and possibly by hydrothermal activity initiated by the intrusion of the Cummings Complex. The evolution of the sedimentary basin with the decrease of its depth is confirmed by the chemo-stratigraphic profiles. Stratigraphic position in the section is important in order that the chemo-stratigraphy may serve as a guide for mining exploration in the distal facies of the Blondeau Formation.

Jan 1, 1984

By E. F. Evoy

"The Gunnar uranium deposit was within metasedimentary rocks of the late Archaen Tazin Group. These rocks were intensely altered by albitization so that the immediate host to the ore consisted dominantly of albite, and by the subsequent introduction of calcite. The ore consisted of disseminated pitchblende and uranophane in a pipe-shaped breccia zone. Oxidation of the ore was more intense near surface than at depth, but there was no near-surface enrichment.IntroductionThe Gunnar Mine site is on the tip of Crackingstone Peninsula, on the north shore of Lake Athabasca, Province of Saskatchewan, Canada. The peninsula forms the southern part of the Beaverlodge mining area. The ore consisted of disseminated pitchblende and uranophane in brecciated metasedimentary rocks of the Tazin Group, and the deposit was characterized by extreme albitization and subsequent carbonatization of the host environment.Production from the mine began in 1954 and the ore was depleted by 1963. In that interval the deposit yielded about 5 million tonnes of ore containing about I. 75 kg/tonne U3O8. It was mined initially from an open-pit and subsequently from underground; the open-pit contributed about 55% of total tonnage. Uranium was recovered by atmospheric leaching in sulphuric acid, ion exchange concentration, and precipitation with magnesia.This paper is based on studies made during the productive life of the mine and is concerned primarily with pre-ore alteration of the rocks containing the deposit, and with the ore mineralogy."

Jan 1, 1986

By S. E. Malouf, W. Thorpe

"The Chibougamau Explorers property comprises 35 claims or 1,726 acres in La Dauversiere and Rohault Townships along the west shore of Norhart Lake. The property is serviced by a twelve-mile all-weather high-way leaving the main St. Felicien-Chibougamau highway at mileage 121. This road junction will be a railway siding on the C.N.R. St. Felicien-Chibougamau branch line in early 1957. The property lies 30 miles due south from the town of Chibougamau. The mine-sponsored Chibougamau Explorers town has a population of 250 with 28 residences and a well equipped recreation centre.The original showing was found by Rider Storn, a prospector financed by Val d'Or interests during the 1950 field season. This showing did not stand up to detailed prospecting but it did lead to the discovery of the main zone by A. Oakley during the following winter.The company was incorporated in I 950 under the presidency of E. Ayrhart. Financing following the initial drilling involved an increase of capitalization from 3 to 5 million shares and the advent of financing and management control by Anacon Lead Mines Limited.Exploration and development to Jan. I, 1956, has included 42,331 feet of surface diamond drilling; 31,363 feet of underground drilling; a 3-compartment shaft to 1,245 feet, with 8 levels at 150-foot intervals; and I 1,054 feet of drifts, crosscuts, and raises. Ore reserves to the 900-foot level, proven and partly developed, total 546,725 tons averaging 0·30 ounces gold and 0·93 per cent copper. A mill with capacity of 500 to 750 tons will be installed by January 1956.GeologyThe Chibougamau Explorers property lies along the belt of Keewatin volcanics striking through Bachelor Lake, Opawica Lake, Doda Lake, Coapatina, Norhart Lake, and Rohault Lake, where it is in close proximity to the paragneisses of the Grenville series. The boundary of the paragneisses, a gradational contact, lies within a mile of the Chibougamau Explorers shaft collar."

Jan 1, 1949

By G. Couture

In the introduction to this presentation, we will cover the market of motorized recreational products. We will introduce the public to what is produced and sold worldwide, what is the nature and general behaviour of the customers for such products. We will cover the evolution of this market and put in evidence how drastic must be the changes in the manufacturers organizations in order to, in one hand, constantly adjust to the customer demand, and in the other hand, react to the competitors' offensives on the market.

Jan 1, 2006

By P. Au, P. Patnaik, H. Saari, D. Y. Seo, S. Bulmer

Ti-48Al-2Cr-2Nb-xW (where x = 0, 0.5, and 1 at. %) powders were consolidated by hot isostatic pressing (HIP). The consolidated samples were solution heat treated above the a-transus followed by stepped cooling to room temperature. Selected samples were subsequently aged at 950 °C for up to 72 hours. The post-heat treatment microstructure was examined by optical and electron microscopy. It was found that increasing holding time above the a-transus generated a more homogenous microstructure. Utilizing the stepped cooling sequence, especially with a transition temperature of 1270 °C, massively transformed gamma (Ym) was diminished. Aging caused coarsening of the fully lamellar microstructure in the 0%W and 0.5%W samples while almost no coarsening occurred in the 1 % W sample. Precipitates began to form during aging in samples containing W. The precipitates at the lamellar interfaces are fine and have a needle like shape, while precipitates at the lamellar grain boundaries are coarse and circular in shape. The size and number of the precipitates depend on aging time and the level ofW content.

Jan 1, 2006

By Forrest A. Kerr

The subject of the Coast Range batholith and its eastern contact zone needs no introduction to British Columbia mining men. Because of its reputed potentialities, this zone has aroused much interest. Because it has touched the pockets of the people by actually producing dividend-paying mines, it has been able, more particularly in certain isolated sections, to retain and accentuate that interest. However, the Stikine River section of the zone has never had the good fortune to have a mine developed, which, through profits or lack of profits, could create such interest. The Cassiar district, beyond the Stikine River area, has been a lure to the prospector for over half a century and was still strong enough in the last few years to attract close to a million dollars in capital and labour. All of this has passed through the Stikine river area, has looked at it, and ignored it. Sufficient interest has never been aroused in the area to bring forth an effort to see what is there, in spite of the fact that it belongs to the same zone in which some of our richest mining camps are located. Because the contact zone of the Coast Range batholith has long been recognized as an ore producer of considerable potentiality, the Geological Survey some years ago formulated a plan to map as much of this area as possible in order to assist in promoting its development. This plan has been furthered during the last fifteen years whenever opportunity presented itself, until today a fairly large part of the area has been covered. The work which has been done on the Stikine during the last two years is the beginning on what is the largest remaining gap in the general plan.

Jan 1, 1928

By D. J. Charlton

"IntroductionMaintenance is a business, which to be successful, requires good management, systems and reporting. The prime objective of the maintenance management group, be they large or small, must be to anticipate and prevent interruptions in operations by keeping equipment in good mechanical condition. This objective should be carried out at minimum cost consistent with maximum productiveness.The objective of this chapter is to give an insight into the various aspects of maintenance management that must be considered to effectively and efficiently operate a mill complex. The degree to which the maintenance sub-systems are developed in an operating mill will be determined by the size of the mill and the needs of the operation.The criterion of the management system used is that the system serve the operation and not vice versa. The systems presented should be considered as tools and, as with all tools, they must be sharpened and replaced as the need arises or as more effective tools become available.To understand what is involved in maintenance management, it is worthwhile to consider a systems approach to analyzing management problems. This approach was developed by J.A.B. Rae while reviewing maintenance management systems for Cominco Ltd.A very simple system involving managing results and objectives is shown diagrammatically in Figure 1.The systems approach to organizational development involves four basic elements: an objective, a result, an activity and feedback. In the analysis, the activity element is broken down into individual actions that people could be held responsible for. If we introduce the action of operating into the diagram of Figure l, we arrive diagrammatically in Figure 2."

Jan 1, 1989

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

By Brian Putland

Single stage semi-autogenous / autogenous (S/AG) milling has become a common design for a variety of ore types with the advantages of being comparatively low capital cost and flexible for future expansion. The single stage SAG/AG milling option is ideal for starter projects with significant exploration and expansion potential. Currently a number of the largest SAG mills designed are installed in single stage configuration. This paper discusses the challenges associated with the process design of single stage SAG/AG milling circuits, the design flexibility required to ensure a robust circuit and the operating techniques adopted at successful installations.

Jan 1, 2012

By A. A. Bakke

"The Fort Knox gold deposit is hosted within the Fort Knox Pluton, a Cretaceous multiphase granitic body that intrudes the Fairbanks schist. Gold occurs along the margins of stockwork veins and veinlets, quartz-filled shear zones, and along fractures within the granite. The mineralization is generally sulphide-poor and closely associated with trace amounts of bismuth, tellurium and to a lesser extent with molybdenum and tungsten. At present, proven/probable reserve estimates, based on a cutoff grade of 0.39 g/t Au, are 158.3 million tonnes grading 0.83 g/t Au.The Fairbanks schist comprises the bulk of the country rock. The dominant lithologies present include muscovite-quartz schist and micaceous quartzite. Immediately north and south of the main orebody, mixed metamorphic lithologies of the Cleary sequence, a subunit of the Fairbanks schist, have been mapped. Development of local zones of weakness, most likely due to a broad regional warping event, resulted in brittle-ductile deformation and activation of a northwest-southeast shear couple between contrasting lithologies.The Fort Knox Pluton consists of at least three phases based primarily on textural differences. Intrusion of a fine-grained granite was followed by a medium-grained porphyritic granite. The youngest intrusive phase is a coarse-grained, seriate porphyritic granite, the Vogt Stock. The Vogt Stock forms an elongate dome with the axis in the east-west direction. Structures displayed in the overlying units, believed to be the result of doming, include tension fiSSUres and longitudinal fractures.Premineralization fractures, the result of the magmatic doming, provided conduits for initial stockwork quartz vein development and quartz enrichment in shear zones. Weak development of vein-controlled phyl/ic, potassic, albitic, and argillic alteration styles are present. Evidence of a late thermal event resulting in a low-temperature alteration assemblage of calcite + zeolite (stilbite) + chalcedony + clay occupies breccia zones, joint surfaces, and fractures within the granite."

Jan 1, 1995

By Charles "Chick" Rodgers, Anthony Sarion

"With declining feed grade and increased production targets, it became necessary to upgrade Key Lake's eight stage counter current decantation (CCD) circuit. Following laboratory trials, mill operations recognized that dilution of the feed slurry and buffering of the feed density variations would improve thickener throughput. Plant testing resulted in the installation of Outokumpu's Supaflo ""Floe-Miser"" system. The circuit's flowsheet, instrumentation and control strategy were also upgraded along with the thickener feedwell modifications. The paper will also discuss these modifications and the implementation of the current control strategy.IntroductionCameco Corporation's Key Lake operation is the largest single uranium producer in the world. Current production is fourteen million pounds of uranium oxide (U 308) per year. It is owned 2/3 by Cameco and 1/3 by Uranerz Exploration and Mining with Cameco as the operator.The mine is 570 kilometres north of Saskatoon on the southern edge of the Athabasca basin. Access to the mine is by an all-weather road and a private airstrip.Process DescriptionThe Key Lake milling process consists of five individual plants: crushing and grinding; leaching and counter current decantation (CCD); solvent extraction; yellowcake precipitation and ammonium sulphate crystallization; and bulk neutralization (Figure 1 -Simplified Mill Flowsheet). A detailed mill flowsheet can be found in the appendix."

Jan 1, 1998

By LUKE O. LINDOE

A major clay products industry in the Medicine Hat area since before 1910 has maintained a continued interest in the clays of the Cypress Hills. For the first forty years the materials used were local red-burning Cretaceous and Pleistocene clays and sands and high-quality stoneware clays of the Whitemud Formation at Eastend, Saskatchewan. Recently a much broader spectrum of raw materials has been brought into use. Including the exposures of the Eagle Butte structure, the Cypress Hills present a 1200 m section of clay-like sediments. Of this 1200 m about 94 per cent, the high montmorillonite shales of the Upper Cretaceous, can be considered useless, or nearly so; the remaining six per cent, all fresh-water beds, presents a wide variety of potentially useful materials. The development of these clay resources is complicated by deep surface creep on the south flank of the Cypress Hills, by largescale slumping on the north flank and by a structural complex in the Eagle Butte area.

Jan 1, 1984

By K. G. Chipman

The Geological Survey is the oldest map making department in the Canadian Government service, and when organized in 1842, one of the first principles to be recognized was the absolute necessity of having good maps. The primary purpose of the Survey has always been geology; but because a graphic representation by means of maps makes the written report .more readily intelligible; because the correlation of known geological facts is often difficult or nearly impossible unless they can be represented on a map; and, because the public demand information shown in this way, the Geological Survey must continue to supply maps; and the supplying of these maps must be considered as an essential part of the work of the Survey. It is a commonly recognized principle of pedagogics that an appeal to the eye is quicker than one to the ear; that children (and others) learn more quickly when a thing is presented to them through the eye rather than through the ear. The application of this principle to the work of the Geological Survey is that, to a large number of people, the message of a map is more quickly grasped, is more readily intelligible, and is in many ways of more interest and value than is the same information in a report. I do not mean that the maps are of more importance than the reports.

Jan 1, 1924

By A. Monballiu, J. A. Martens, Y. W. Chiang, A. Van Audenaerde, R. M. Santos, T. Van Gerven, B. Meesschaert

In this work, bioleaching of non-sulphidic materials by applying chemoheterotrophic bacteria and fungi is studied. It was found that the tested fungus, Aspergillus niger, leached substantially more nickel from olivine than the tested bacterium, Bacillus mucilaginosus. A. niger also outperformed fungal species Humicola grisae and Penicillium chrysogenum in the leaching of olivine. Contrary to traditional acid leaching, the microorganisms leached nickel preferentially over magnesium and iron. On average, a selectivity factor of 2.2 was achieved for nickel compared to iron. This can potentially facilitate postprocessing of the leach liquor and reduce the cost. The impact of ultrasonic conditioning on bioleaching was also tested, and substantial increase in nickel extraction with A. niger was observed. This was credited to an increase in the fungal growth rate, the promotion of particle degradation, and the detachment of the stagnant biofilm around the particles. Furthermore, ultrasonic conditioning enhanced the selectivity of A. niger for nickel, resulting in a selectivity ratio for Ni/Fe equal to 3.5. The chemical resistance of the selected microorganisms to several heavy metal and metalloid (As(III,V), Cd, Cr(III,V), Ni, Pb, Zn) was evaluated. It was found that, with the exception of As(v) and Cd, A. niger has high tolerance to these components. Therefore, this biohydrometallurgical route can potentially be applied to non-sulphidic wastederived materials, such as industrial slags, ashes and sludges.

Jan 1, 2014

By E. C. Keeley

Some Safety Measures at Ontario Mines The following safety precautions have of late been taken by several of the Ontario mines: installation of water crossovers; washing clown of faces to show-up missed holes; insistence on gloves being worn as a protection to men's hands; wearing of safety boots and hats by underground men; and wearing of goggles by all men using hammers, starting holes, etc. In the summer of 1924 the Mclntyre mine began experimenting with means of removing powder smoke from headings by installing fans and pipe-lines of various designs, also with different means of introducing water into the air-blast when blowing smoke. By October of that year they had devised a scheme of water connection between the water and the air line, at a distance of about one hundred and fifty feet back from the face, using two valves and a short hose. By this means a limited amount of water could be introduced into the air which blew into the face, resulting in a fine spray of air and water combined. This spray not only helped to eliminate fumes but also introduced fine particles of water into the air, raising it above the dew point, with the result that when these fine particles of water settled they had attached to them fine dust particles, thus eliminating, to a great extent, the injurious dust caused by blasting. The combined air and water is turned on immediately after blasting and allowed to blow continuously for from four to five hours, until the muckers come on shift.

Jan 1, 1931