Search Documents

By Q. Dong, S. A. Nightingale

An investigation has been carried out to assess the effects of an applied voltage on the dissolution rate of MgO refractory in a steelmaking like slag. In this study corrosion results obtained from dip tests using a dense direct bonded MgO refractory in a CaO-SiO2-Fe2O3-FeO-MgO slag are presented. These results demonstrate that the application of a voltage across a dense MgO refractory-slag interface can change the rate of refractory dissolution. For the slag composition used and the voltage range tested, it was found that a maximum corrosion rate was obtained at a voltage setting of -0.45V. The results of this investigation have been explained in terms of voltage affects on Marangoni (interfacial tension induced) stirring and its effect on the MgO dissolution reaction that is at least partly controlled by mass transfer in the slag.

Jan 1, 2004

By M. Kawahara, H. Sunayama

Oxidation rates of the cubic specimens, which were prepared by cutting the shaped magnesia-carbon bricks, were measured continuously with a thermo balance in the temperature range from 1273 to 1 823 K in N2-02 and Ar-02 mixed gas with 2.1 x 104 and 3.7x 102 Pa of oxygen partial pressure respectively. The effect of the graphite content, the maximum grain size of magnesia clinker and the oxygen concentration in the atmospheric gas on the oxidation rate for the MgO-C refractory has been investigated. The value of effective diffusion coefficient of O2, which diffuses through the porous decarburized layer, decreased with the decreasing of the porosity and the oxygen concentration in the external gas phase. It was speculated that the dense layer formed easily due to the high tortuosity of pores and the low recession speed of the carbon interface in the MgO-C bricks.

Jan 1, 2004

By S. Afshar, C. Allaire

Several studied have recently shown that the use of non-wetting additives is not always a sufficient solution to improve the corrosion resistance of refractories against molten aluminum. Once in contact with liquid aluminum, the coarse aluminosilicate aggregates, which do not benefit from the protective effect of non-wetting additives in the matrix, may be corroded. In some cases, the corrosion of aggregates, especially those containing a significant amount of free silica and/or alkalis, promotes corrosion in the surrounding matrix. The present work explores the possibility to protect the poor corrosion resistant aggregates via a lining procedure. A slip casting method, using either alumina or celsian-like composition based slurries, has been applied for lining of a series of aggregates. The results from this study show that such linings may prevent efficiently the corrosion of aluminosilicate aggregates. This work also analyzes the effects of firing temperature and lining quality on the corrosion behavior of aggregates

Jan 1, 2004

By P. Stantke

Glue, thiourea and chloride are the common reagents which are used in copper electrorefining to achieve fine-grained and smooth copper deposition. While thiourea and chloride are clearly defined chemical substances, glue is a natural product consisting of a mixture of amino acids in different constituent parts. The amino acids are continually degraded in the electrolyte by hydrolysis until they finally become completely inactive. This effect is well-known, largely constant and balanced by the continuous dosing of glue. In contrast, the behaviour of glue in the batch container is not always foreseeable. The glue can become partly or completely inactive by contamination with acid or bacteria, for instance. Usually this is not noticed, and partly or fully inactive glue is added to the electrolyte over a longish period, with the result that the copper growth is significantly impaired. Examples from operational practice show that, with the help of the CollaMat system, partly or fully inactive glue batches can be quickly detected.

Jan 1, 2007

By Inga Tuzovskaya1i

Three types of gold species were observed for gold-zeolites, prepared by reduction of ionexchanged Au species in a series of zeolites: (i) Au3+cations, (ii) neutral Au0 n or charged Aus+ n clusters suggested to be inside the zeolite channels, (iii) Au nanoparticles with diameter varied from 2 through 20 nm located on the external surface of zeolite microcrystals. Contribution of the gold species formed in zeolite after the ion exchange was found to depend on zeolite type, acidity of zeolite, temperature of reduction and time of storage of the exchanged and reduced Au-containing zeolites. Au3+ ionic species and clusters Aun were formed after the ion-exchange procedure (in contrast with the familiar production of Agn in same zeolites). Gold nanoparticles were observed only as the result of reduction of the Au-exchanged forms at elevated temperatures due to reduction of Au3+ species and aggregation of clusters.

Oct 1, 2003

By D. Harris, S. Murugesan, G. Ye, G. Oprea, J. Rigby, T. Troczynski

The spinel-added and in-situ spinel bonded castables have been developed and widely used in steel industry. It is challenging to develop magnesia-based castables for the non-ferrous industry because the temperatures in industrial furnaces are significantly lower than those in the steel industry and therefore the binding systems of these castables must have the capability to develop a ceramic matrix below 1300°C. It is also challenging to develop a good binding system without addition of fume silica, because the hydration of magnesia may take place during installation, curing and firing of the castables. This work presents the experimental results on developing magnesia-based cement-free, silica fume-free refractory castables using hydratable alumina as the hydraulic binder and a spinel phase as the final ceramic binder. In order to activate the sintering and have a ceramic matrix well developed at the relatively low required temperatures, ultrafine aluminas, chromia, magnesium-aluminate spinel and aluminum titanate powders were used as components of the binding system.

Jan 1, 2004

By Larry Urbanoski

"This paper describes the application of a radioisotopic energy dispersive X-ray aY1alyser to complete on-stream analysis in a base metal concentrator.The major components of the system are outlined and some description of the application, operating experiences and benefits are provided.IntroductionThe ma1n intent of this paper is to describe the on-stream analysis system in operation at the Geco concentrator. X-ray analysis systems installed in Canadian concentrators to-date may be broadly classified as wavelength dispersive analysers whereas the installation described herein is an energy dispersive x-ray analysis system. Energy dispersive x-ray analysis techniques may utilize radioactive sources to provide primary x-rays for excitation of elements and separate the secondary x-rays on the basis of energy levels. In contrast wavelength dispersive analysers apply high voltage x-ray tubes to provide primary x-rays and utilize crystals to disperse and thereby separate x-rays generated by bombardment of the sample."

Jan 1, 1978

By Christopher McElman

Real-time mine management solutions have evolved over time from closed, proprietary solutions, to a "system of systems" that may include a wide variety of off-the-shelf components and technologies. Modular Mining Systems has embraced open standards for their NextGen products to bridge the technology gaps between these systems. However, the remaining logical gaps must be overcome, in order to achieve truly seamless integration between discrete systems. When dealing with volatile real-time management problems, the effectiveness of business process modeling and middle-ware can break down. Scientific principles of military command and control applied to mining domain help to achieve better alignment and reach the highest level of integration. The combination of open standards and off-the-shelf hardware and software with a deliberately structured command-and-control approach provides a clear evolutionary path from ad-hoc connected systems towards real-time management of a seamlessly integrated digital mine.

Oct 1, 2009

By R. Farhat

Coating systems that yield a thermally grown oxide (TGO) protective layer have been proposed as a potential method for extending the lifecycle of components exposed to high temperature corrosion. This is particularly relevant to the petrochemical industry, where any reduction in corrosion rates can yield substantial cost reductions. The primary goal of this project is to develop a coating repair procedure and to investigate the oxidation performance of the repaired location. Electrospark deposition (ESD) was used to repair spalled segments of TGO grown on MCrA1Y substrates using various electrodes possessing mixed crystal structures. Specifically, electrodes of NiCoCrA1Y (BCC-FCC mixtures) and CoNiCrA1Y (FCCBCC mixtures), were deposited and oxidized to develop the TGO using a heat treatment of 24 hours at 1000°C in air. This presentation will focus on the microstructural evolution of the base metal and ESD repair on damaged area, in both as- deposited and oxidized forms. Results of SEM and XRD analysis will be presented.

Jan 1, 2011

By Robert S. G. Chapman, Kieran M. J. Downes

The Sulphide-Preview Lakes area is located 45 km northeast of La Ronge in northern Saskatchewan. It lies within the southern portion of the Proterozoic La Ronge Volcanic-Sedimentary Belt. Two styles of gold mineralization are present in the Sulphide Lake area , stratabound gold mineralization is intimately associated with a pyrite-pyrrhotite-arsenopyrite-bearing graphitic argillite unit within a sequence of intermediate to felsic volcaniclastics. Past operators established three mineralized zones along this horizon with combined reserves for two of the zones, of about 175,000 tons at 0.22 oz/ton Au. In the Preview Lake area , gold mineralization occurs in variably sheared gabbro/quartz diorite sills within a mixed sedimentary-felsic volcaniclastic sequence. Gold occurs with arsenopyrite, pyrite and minor chalcopyrite associated with quartz veins and stringers. A sulphidebearing graphitic argillite unit occurs in close proximity to the mineralized shears. Past operators delineated seven mineralized shear zones, two of which were drilltested. Average gold grades reported are in the 0.1 to 0.2 oz/ton range with erratic values up to 5.0 oz/ton.

Jan 1, 1986

By M. Boussuge

Ceramics and refractories have many common constituents and consecutively exhibit several analogous properties. For example, concerning the thermomechanical properties this paper will focus on, the type of creep that can be observed in both materials is often the same (kinematic hardening). Changes in microstructure (phase transformation, dehydration, sintering, crystallisation,...), induced by heating and/or cooling, can also drastically modify the mechanical behaviour of ceramics and refractories. But the coarse granulates, the porosity and the impurities contained in industrial refractories may lead to specific responses of this material to thermal and/or mechanical loadings. In particular, some differences can be observed with technical ceramics in the main type of damage observed in service : diffuse damage in refractories (microcracking) and localised damage in ceramics (macrocracking). In this paper, the possibilities of transferring a part of knowledge from ceramics to refractories will be discussed, in the field of thermomechanical properties : experimental characterization techniques, mechanical behaviour models. Finally, some problems caused by scale effects and by the integration of thermomechanical properties of refractories in the numerical simulation of industrial structures will be evoked.

Jan 1, 2004

In recent years, China and India have emerged as major players in the copper sector. Over the last decade, around 50% of additional global refined copper usage growth can be attributed to them. The paper provides an overview of the current and future copper supply and demand situation in both countries. Results from two market studies commissioned by the International Copper Study Group (ICSG) are complemented with recent copper statistics on North-East and South-East Asia, as well as further sectoral analysis. Developments and trends in copper mining and metal production, semis production, and major end use areas are highlighted. While providing insights into sectoral patterns and growth trends, the paper provides the basis for comparing structure and output of the copper sectors in some of the major copper-using countries in Asia. Afterwards, the current copper reservoir in use associated with infrastructure, buildings, industrial equipment, transportation systems and households is assessed using the ICSG Copper Flow Model. Finally, the identified copper flows are analyzed regarding the potential impact on the future world supply and demand situation.

Jan 1, 2007

By N. Schmitt, E. Blond, F. Hild

Working linings of steel ladles progressively damage during the steel manufacturing process due to both severe thermomechanical and chemical stresses. In the framework of the coupling scheme proposed by Blond et al. (1), this study examines the effects of the thermomechanical loading on the onset of microcracking by considering that the complex microstructure of the slag-impregnated brick is fixed during the steelmaking process. The behaviour of the refractory is identified by using thermoelastic-(asymmetric)viscoplastic constitutive equations. Numerical simulations of a simplified geometry of the lining subjected to cyclic thermal loadings at the inner side are shown. Two cases are analysed, namely, i) the material is a homogeneous continuum with a thermoelastic-(asymmetric)viscoplastic behaviour, ii) the material is porous and saturated by liquid slag, and the skeleton has the previous non-linear behaviour. The stress and strain fields are shown, and for the porous medium the interstitial pressure of slag as well. Comparisons between these assumptions are made to assess the role of slag on the degradation of the working lining.

Jan 1, 2004

By K. L. Eastwood

The ISA PROCESSTM cathode plate is characterised by its copper coated suspension bar, coupled with a blade employing austenitic stainless steel alloy 316L. The blade material has become the mainstay of the technology and has been closely copied by competing cathode designs. Improvement to the cathode plate design remains a key area for research, and ongoing developments by Xstrata Technology's ISA PROCESSTM have recently been commercialised. Two such developments are the ISA Cathode BRTM and ISA 2000 AB Cathode. The ISA BR cathode is a lower resistance cathode that has proven to enhance operating efficiencies. The AB cathode was designed to improve stripping inefficiencies in the ISA 2000 technology. These developments have now had time to mature and their long term performance will be discussed. Rising material costs and the desire to extend the operating boundaries of the standard 316L cathode plate has triggered a number of significant advances. These involve the use of different stainless steels as alternatives in some operational situations. The technical aspects and results of commercial trials on this development will also be discussed in this paper.

Jan 1, 2007

By J. Lu

The impact of acid treatment in agglomeration/acid curing on copper extraction and acid consumption was investigated with respect to acid dosage and moisture. Without the addition of water, no agglomeration occurred. At an acid dosage above 15 kg/t, the acid was not completely consumed during acid curing. With the addition of 6.2% water, the particles agglomerated together. Copper, iron, magnesium and manganese were dissolved as sulfates and enriched in the fine fraction of the ore. The copper extraction and net acid consumption increased with increasing acid dosage. The copper extraction for acid curing with the addition of 6.2% water was higher than that without the addition of water due to the improved permeability and the increase in the contact with acid-soluble copper. During acid curing, the reaction of sulfuric acid with muscovite, abite and nacrite mainly took place on the surface of the particles while the reaction of sulfuric acid with clinochlore occurred not only on the surface but also inside the particles.

Jan 1, 2007

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By A. G. Pentland

PROSPECTING is popularly supposed to be surrounded with an air of romance and adventure. The word 'prospecting' brings to mind high mountains, northern lakes, and aeroplanes. A note of urgency has been added to this by the war, particularly in the case of strategic, minerals. Prospecting for strategic minerals in a modern mine in full production, although it may Jack the romance of travel in little-known places, has the advantage of having all the necessary machinery at hand and ready to go into action at a moment's notice. HISTORY Tin was discovered in the Sullivan ore in 1925, when a white streak was noticed on a pilot table which was being used to check the amount of galena in the tailing. The mineral which made up this streak was identified as cassiterite. The amount of tin in the ore is so small that, while of scientific interest, it was considered to be of very little economic importance. Nevertheless, several attempts were made to learn something of the occurrence during times when other work was nor pressing. These studies were dropped when anything came up that seemed more important.

Jan 1, 1943

By K. Karan

Oxygen reduction reaction in PEM fuel cell cathodes involves participation of three reactants - oxygen, hydrogen ions, and electrons. Electrochemical reaction in the catalyst layer is, therefore, influenced by how these species are transported to the reaction site. The two-phase boundary locations at which percolating networks of ionically conducting electrolyte and electronically conducting Pt/C meet are feasible reaction sites. The electrolyte phase also provides pathway for the transport of dissolved oxygen. Most of the 3-D models describe the catalyst layer as an ultra-thin layer, thereby, losing useful information on the distribution of electrochemical reaction rate. In this paper, we extend our previous work on 2-D cross-the-channel modeling of PEMFC cathode based on agglomerate catalyst layer. In particular, we take a closer look at the influence of proton conductivity on the reaction rate distribution in the catalyst layer. As well, we re-examine the role of anisotropic transport coefficient of the porous transport layer (PTL), commonly known as the gas diffusion layer, on the current density distribution under the channel and the rib of the flow-field plates. Results from both a 2¬D and a 3-D models will be presented.

Jan 1, 2005

By G. Langlands

"R. Tenbergen Is this flotation machine suitable in the flotation ofInco ball mill discharges where we have a coarse feed at 60% solids?Reply Experience has shown that there is not a significant increase in the wear life of these machines when handling coarse material (8 mesh) at 60% solids. A common practice in Europe is shut down on the week-ends.The material is allowed to settle and on start-up an injectic of air for 15 seconds is sufficient prior to start-up. At,mining we put our unit in the middle of a bank of 44 cells and in order to ensure severe sanding we shut the aker cell down while the remaining cells kept running. After 20-25 seconds of air the cell started without trouble.P. Mahant Is there a build-up inside the impellor shaft housing? Falconbrige Ltd.Reply There is no sand build-up but rather a scale build-up which due to a flexing action frees itself periodically. Part of the design of the machine permits a water injection into the shaft housing to free any build-up. This is done in Europe during the week-end shut down."

Jan 1, 1984

By M. D. Viera

The purpose of the study is to show, through real cases of companies in Chile, the different problems concerning valuing or economically appraising a mining ore resource with the traditional techniques. The study demonstrates that, with the risk analysis and real options theory application, one could determine the most probable value for a mining resource or mining business, and the risks cover of uncertainty scenarios. The study discusses different methods and criteria employed in the ore resource evaluation or mining assets. It also shows a comparative analysis of the different methods in order to explain various distortions, errors, risks and imprecisions of each of them. the companies are becoming aware of the risks' importance and the impact they have on the commercial value and resource estimation models. Now, the real options are the techniques that somehow make it possible to value and control the risk cover of the business. The company valuation could help respond questions like: ? How much is my business worth? ? How much has the investment profitability of my business been? What could be done to improve this profitability and create value?

Jan 1, 2007