Search Documents

By Romano J. Micciche

One of the largest scale uses of a multiple, high-strength steel bar tiedown system is described. Tiedowns were installed to resist hydrostatic uplift forces acting on a section of the Interstate Highway Route I-90 southern approach roadway to the Third Harbor Tunnel, in Boston, Massachusetts. Site specific information is discussed regarding design, testing, and installation of Tiedowns. Conclusions are presented regarding the overall performance of this system and the application of this type of tiedown system on future projects.

Jan 1, 1994

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By Haijian Shi, Drew Pizzo

This article focuses on the appropriate application of subsurface investigation methods for transmission structures, which are typically designed to resist lateral rather than vertical loads. Currently, the three methods used most often for the subsurface investigation of transmission structures in the field are the Standard Penetration Test (SPT), the Cone Penetration Test (CPT), and the Flat Dilatometer Test (DMT). Each of these methods has advantages and disadvantages, and each is more applicable to some scenarios than to others. To gain a better understanding of these test methods and the implications of using them for various kinds of applications, a comparison study was conducted in the field in Maryland, for three boring locations. Each boring location was explored using each of the three tests as stated. The results of the tests and lessons learned are presented and compared, and these comparisons show that the three test methods agree on the majority of the findings. The results from each test method were also used to derive key parameters such as the soil friction angle for given foundation designs considered in order to establish a clear basis for comparison. Recommendations for performing transmission structure subsurface investigations are made in order to optimize the use of each method and thereby optimizing subsequent foundation designs. INTRODUCTION For overhead transmission structures, the most important structural requirement for determining the foundation design differs from the requirement for other structures such as buildings and bridges in accord with the conditions the transmission structures will need to withstand. In addition to the ability to bear a given vertical load consistent with its use, the foundation must bear lateral loads arising from wind and other weather conditions. The foundation types used most often for overhead transmission monopole structures include concrete drilled pier, vibratory caisson, and direct embedment. In order to determine an appropriate and even an optimum foundation design for any given set of conditions, an appropriate subsurface investigation method or approach is needed. Currently, the standard penetration test (SPT), the cone penetration test (CPT), and the flat dilatometer test (DMT) are the three most commonly used subsurface investigation methods.

Jan 1, 2018

By J. C. W. M. de Wit

An excavation, within which a tunnel is sunk as a part of the Centraal Station underground station (platform section) of the Noord/Zuidlijn ('North/South Line'), is to be created beneath the Amsterdam Centraal ('Amsterdam Central') station. The section beneath Amsterdam Centraal Station is characterised by the application of a particular technology in the form of, inter alia, the so-called 'sandwich wall'. This is a composite wall consisting of two rows of Tubex piles with a body of jetgrout columns in-between. This wall acts both as an excavation support wall and also provides vertical bearing. The installation of the wall, including both Tubex piles and jetgrout columns, within these specific conditions (limited height, sensitive historical building), within the design requirements set in terms of construction tolerance and water and soil retention, may be regarded as being a pioneering achievement. The environmental constraints are that the trains should continue to run, the inconvenience to passengers should be kept to a minimum and the historic station should not suffer any damage. Because of the complexity of the working conditions, the project is being overseen by a steering group of experts in the specified construction processes. In order to manage the project risks, jet grouting trials were initially carried out, in order to highlight and control execution problems; the practicability of the design is then tested. Work commenced on the sandwich wall in 2003, when the wooden piles were extracted at the locations where the sandwich wall was to be constructed; in 2004, the steel Tubex piles for the southern wall sections were installed. From May 2005, the construction of the sandwich wall got under way; in addition to the described process supervision, an extensive measuring programme was established, so that the process could be adjusted as necessary and the quality of the finished product determined. This applied to both individual columns and for the end product, the sandwich wall. The measurement results were processed for each column, interpreted and the effect on the work still to be conducted was assessed for each future column. Preventative and corrective measures were, if necessary, taken in order to control or counteract the measured defect. In addition to the process-oriented and qualitative measurements, various independent measurement systems at the station building served as a further control in order to prevent damage to the building.

Jan 1, 2006

By Donald J. Murphy

Longevity of structural units, as compared to the planned useful life of a facility, always is a design consideration. Typical concerns include slow decay due to environmental factors, and changes in constitutive relationships governing the performance of the material involved. With respect to foundations, the usual items of interest are corrosion of steel and concrete, and time dependent behavior of the soil/structure system. For piles, as with other foundations, deterioration is precluded, mitigated or otherwise accounted for by assessing properly the ambient situation (sulphates, pH, stray currents, resistivity) and providing safeguards, such as resistant construction products, oversizing, coatings, and/or cathodic protection. On the other hand, long term performance of the pile foundations, as affected by time dependent characteristics of the supporting soil or rock, can be predicted and controlled only with a synergetic coupling of analyses and field tests. The history of a project for which this approach was followed forms the basis for this paper.

Jan 1, 1986

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By Tom A. Armour

Different variations of soil nailing techniques have been used in the United States since the late 1970's. Such techniques owe their origins to French developments, which began in the early 1970's as a spin-off from European tunneling excavation support practice. The growing demands of urban infrastructure development and rehabilitation and environmental protection have created an active and expanding soil nailing market demand for earth retention and slope stabilization in the United States since its early developmental years. There is a clear need for a fundamental review of the large number of soil nailing techniques that are currently being used in the United States. Following a brief summary tracing the historical development of soil nailing and a generic classification of applications, this paper provides a review of the different recent advances in the design and construction of soil nailed systems. Discussion topics include nail design advances, permanent "top-down", structure support/underpinning, alternative face stability measures, composite systems, hollow bar and fiberglass nails and architectural reinforced concrete/shotcrete facings. Case histories will be presented to illustrate each of these advances.

Jan 1, 2003

By Andrew L. Peterson

CATOH Inc. of Weedsport, New York recently completed a very challenging Bored-In Pile project which features unique construction techniques in the installation and load testing of 45 and 100 ton capacity piles. The bored-in piles were installed on a twenty-nine million dollar New York State Department of Transportation project which began in the fall of 1995 and ended in March of 1997. The project included the construction of 5 new bridges to alleviate a very congested traffic network which had come to be known as the "Octopus" in the small city of Ithaca, New York. CATOH Inc. was awarded the piling contract by general contractor Santaro Industries in the fall of 1995. Piling installation work was completed in March of 1997. BACKGROUND The project is located at the southern tip of Cayuga Lake which lies in the heart of Upstate New York's Finger Lakes Region. This region is popular not only for wine making and vacationing, but also for its impressive geological history. The glacial activities that helped to form the deep valleys of this scenic area are also responsible for creating challenging underground conditions for deep foundations work. CATOH developed two pile designs to accommodate differing site conditions on the project. Internally reinforced piles were developed for use in the center of the valley and externally reinforced piles were developed for locations close to the valley wall.

Jan 1, 1997

By Ingemar Hermansson, Thomas Bjerendal, Mattias Grävare, Carl-John Grävare

"AbstractHigh strain dynamic pile tests (HSDPT) on driven piles have been carried out on a routine basis in Sweden for more than 30 years. The Swedish Commission on Pile research established, in the early 1980s, safety factors based on the percentage of piles tested. The safety factors could then be reduced, creating economic incentives for the contractor to carry out testing.Energy formulas adopted by our neighbour countries, Norway and Denmark, were not accepted in Sweden as a reliable method since the dynamic testing method was considered to be a more scientific and reliable method. It has become almost the only in-situ method used to verify geotechnical bearing capacity on driven piles.The typical Swedish geology of soft soils overlaying very hard strata makes it possible to verify high design loads, typically 20 kN per cm2 of pile cross sectional area for steel piles and 1,5 kN per cm2 for concrete piles.Conventionally a certain percentage of the piles have been tested in Sweden. The EC7, on the other hand states a number of piles to be tested, regardless of the total number of piles. The Swedish NA (National Annex) states a maximum distance between tested piles, which results in better distribution of the test piles over the foundation.For shaft-bearing piles in soft clays, dynamic pile tests have to be correlated by static load tests.Historical backgroundOn a research basis stress-wave measurements have been carried out for a long time in Sweden. One example is a project in the city of Gothenburg, conducted by Fellenius and Pejrud (1964). Strain gauges were glued on the reinforcement bars in 60 m long, precast concrete piles at 3 m and 25 m above the pile tip respectively. Evaluation was done with different methods such as dynamic formulas,stress-wave measurements and in addition compared with static load tests.In the 1975 Building Code in Sweden, driving criteria for concrete piles based on stress-wave theory were introduced, as summarized in Table 1. The driving criteria are intended for 3 and 4 tonne gravity hammers. For hydraulic rigs, which have free-falling hammers, the drop height indicated should be reduced to 80 % of the values in the table. The criteria were considered to include a safety factor of 3,0. For 330 - 450 kN pile load, pile with a standard a cross sectional area of 235 mm x 235 mm was used. For 600 kN load, the standard cross sectional area was 275 mm x 275 mm."

Jan 1, 2014

By K. Rambha Devi

The paper is an attempt to co-relate the findings of pile capacity using a number of formula suggested by various authors with the actual field load test results. Five locations consisting of wholly sandy or clayey soils were selected for this purpose. The clayey soils are on a hilly area having clays of medium to stiff consistency upto a depth of 20 m The sandy soils are near the bank of a river having angle of internal friction 'Ø' value ranging from 30 to 35 Degree. The details of the soil properties are given in Table-1 Bored cast-in-situ piles of 30 cm diameter and a length varies from 6.5 m to 13 m were designed and cast for load test to be carried out. The load applied was twice the design load. The load vs settlement curves were obtained. The theoritical values obtained by formula suggested by various authors were superimposed on the curves. From the careful study of these curves it is seen that De Ruiter and Berigen values are close to the actual results for clayey soil. For sandy soil it is found that both the BIS method and Meyerhof method found to give conservative resuslts. A multiplication factor is suggested to theoritical values for obtaining satisfactory results.

Jan 1, 1996

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By B. B. Broms

A method for calculating the bending moment induced in misaligned or bent piles is described, The maximum bending moment varies with the angular rotation between the pile segments, the coefficient of horizontal subgrade reaction of the soil and the flexural rigidity of the piles. A case history involving damages to misaligned 365 x 365 mm square precast concrete piles is described.

Jan 1, 2010

By Cristhian C. Mendoza, Renato da Cunha, Bernardo Caicedo, Max Barbosa

"Abstract This paper shows that a raft alone is not sufficiently appropriate to address the uncertainty of underlying soil variability; therefore, a piled raft system is a better option for mitigating such uncertainty. To study the variability of soil, the behavior of the Piled-Raft Foundation was analyzed with a type of self-drilling micropiles: the ""Alluvial Anker"" (common name for this pile type in Brasilia city). These micropiles have been used in the city and have the advantage that the drill pipe also serves as reinforcement. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soil; variability of these parameters can be intrinsic and/or epistemic. Simulations were performed for a hypothetical Piled-Raft Foundation subjected to vertical loading using the random finite element method. The average parameters of the constitutive model were obtained through laboratory tests. The simulations of the load test were compared with results of a real scale experimental test conducted exclusively for this work in the field. It is analyzed the relative importance of the variability of some geomechanical parameters and their variation with depth is considered. In addition, it is discussed a comparison between the uncertainty of the geomechanical parameters and the uncertainty of the results of the vertical loading test. Finally, this paper shows that a decrease of the safety factor may occur when taking into account the variability of the parameters.IntroductionBrasilia is located in a highly weathered residual tropical soil (lateritic & latossol on pedogenetic concepts). This soil presents high content of alumina and iron due to the lixiviation process of the upper layers. As a consequence, the cemented structure is highly unstable and it can generate strong changes of volume (i.e. collapse) due to changes in both moisture and state of stresses. Therefore, a greater understanding of the construction of Piled-Raft Foundation systems on this particular soil conditions is needed – especially because it covers more than 80% of the surface area of the Brazilian Federal District.Thereafter, this work investigates the influence of the variability of the soil parameters over the uncertainty of the Piled-Raft Foundation design. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soils. The simulations were performed for two hypothetical Piled-Raft Foundations subjected to vertical loading by using the stochastic finite element method. The results were compared to real load tests in Piled-Rafts with “Alluvial Anker” pile types."

Jan 1, 2014

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

By A. Lyndon

Vertical and lateral load tests were carried out on two 13 m deep bored cast-in-place instrumented piles, socketed into weathered sandstone. The first pile, 1200 mm in diameter, was loaded vertically to a maximum of 16000 kN and then loaded to failure under lateral load (1900 kN). The second pile, 1500 mm in diameter, was tested under lateral load up to a maximum of 2400 kN. It was found that the deflections of the 1200 mm pile were more than twice those of the 1500 mm pile under similar loads. The soils on the site are not easily tested in the laboratory, or by conventional insitu site investigation techniques, parameters needed in design can only be reliably obtained from pile test results. In this report shear moduli are back analysed from the vertical load test and the two lateral load tests. For these similarly installed piles very different design parameters were determined from the lateral load tests, the only known major difference between the piles being that the 1200 mm pile was loaded vertically before it was loaded laterally. Changes in G values needed to match performance under vertical load if applicable to lateral loading could have accounted for a significant amount of the difference.

Jan 1, 1989

By Upendra L. Karna

The pile capacity gain with time evaluated and implemented for the construction of the Route 21 Viaduct in Newark, NJ, U.S.A is discussed in this paper. The project consisted of the replacement of more than 3.2 km of viaduct and ramps. The project site consists of thick residual materials deposited by the Wisconsin Glacier over sedimentary rocks. The upper portion is glacial-lacustrine deposit underlain by marginal morainic till and stratified drift. Subsurface investigations identified significant variations in layer thickness and grain size consistency. The site was characterized into 4 Soil types, based on subsurface soil behavior. Closed end 600 mm and 450 mm diameter driven pipe piles were used for the foundation. Loading tests conducted during an advanced construction contract, established that a significant soil set-up could be expected. For the first construction contract, a pilot loading test program consisting of 112 dynamic loading tests and 77 re-strikes (at 2 to 4 weeks) using the PDA (Pile Driving Analyzer) with CAPWAP (Case Pile Wave Analyses Program) was conducted to establish the soil set-up behavior. Nine (9) quick static loading tests were conducted to substantiate the long-term pile capacity. Based on the loading test results, average set-up factors were established and utilized for developing production pile driving criteria. Bearing resistance with depth was analyzed and reviewed. The set-up factors varied significantly, ranging from 1.05 to 1.89, and averaged about 1.30. Conclusions are derived. Set-up factors behavior for each soil type plotted by linear regression are presented and discussed. An appropriate set-up with time relationship for a glacial soil is suggested.

Jan 1, 2006

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2005

By Hodjat] [Shiri

A 4-legged jacket structure was installed by an Offshore Installation Contractor (OIC) in the Persian Gulf. In addition to four open-end pipe piles, six conductors were installed by OIC. During the installation of the piles and conductors, some cemented layers were encountered, which had not been accounted for in the foundation design performed by an independent well known offshore geotechnical site investigation contractor (OGSIC). Six months later, the Drilling Company (DC) hired by Client to execute the wells, reported that all of the six conductors were presenting anomalies, such as vertical misalignments up to 10o and/or collapse of the conductors tip and mid height. The DC faced with serious problem in drilling of the wells and in spite of several times milling the conductors and spending 40 days unpredicted extra time, some of the routes could not be opened and Client lost millions of dollars due to direct and indirect associated costs and expenses. This paper presents a complete overview of all engineering, construction and specially geotechnical investigations and shows that how an inaccuracy in interpretations of the results of an offshore geotechnical site investigation as the main reason in this case study can cause serious damages to whole project with unbelievable time and cost impacts some times up to millions of dollars.

Jan 1, 2006

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002