Search Documents

By Robert J. Willard

This chapter includes tables from 1983 that were not available in time for publication of the 1983 Minerals Yearbook, but does not include corresponding tables for 1984. The value of raw nonfuel minerals produced in the United States during 1984 was estimated at $23.2 billion, an increase of $2.1 billion over the value for 1983. This is the second consecutive year that the value has increased, and except for a decrease in 1982, the value for each year has increased since 1971, or 12 out of 13 years. In 1984, 16 out of 21 metal commodities increased in output while 5 metals decreased; 14 metals increased in value and 7 decreased. Of 46 nonmetal commodities. 37 increased in output while 7 decreased and 2 remained unchanged; 35 nonmetals increased in value and 11 decreased. These statistics are grounds for continuing the cautious economic optimism expressed in 1983. Despite the note of optimism, however, numerous problems plague the mining industry, weakening its stability and inhibiting its growth potential. The problems are a complex mix of international and domestic factors that have been building in the recent past, but have become even more troublesome in 1984.

Jan 1, 1985

By Jacqueline V. Rich

The relationship between surface and ground water quality and copper mining in the Globe-Miami area is investigated in this three-year study. Methods to prevent, minimize, mitigate, or treat polluted waters are identified and evaluated. Best Management Practices are incorporated in a recommended plan to manage the area's water quality.

Jan 1, 1983

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959

By R. L. Marek

The number of Persons fatally injured in the petroleum industry in California in 1930 was 50, a decrease of 20.6 per cent from 1929, when 63 men accidentally lost their lives. The decrease in the number of fatalities for 1930 has caused the first downward trend in the fatality curve of the California petroleum industry since 1927 and is coincident with a period of little active development in new fields, the shutting in of many wells, and reduced activity in the older fields of the State. That a direct relationship exists between the number of accidental deaths and the rapidity of new field development is particularly emphasized by the fact that in 1929, a year of intensive field development in California, 48 men were killed in the drilling and producing division, whereas in 1930, a year of less development work, only 25 men were killed in this division. The figures for the average number of drilling and producing wells in 1930 decreased appreciably from comparable figures for 1929 and a greater percentage of producing wells were shut-in in 1930 than in 1929.

Jan 1, 1931

By R. L. Marek

The number of persons fatally injured in the petroleum industry in California in 1930 was 50, a decrease of 20.6 per cent from 1929, when 63 men accidentally lost their lives. The decrease in the number of fatalities for 1930 has caused the first downward trend in the fatality curve of the California petroleum industry since 1927 and is coincident with a period of little active development in new fields, the shutting in of many wells, and reduced activity in the older fields of the State. That a direct relationship exists between the number of accidental deaths and the rapidity of new field development is particularly emphasized by the fact that in 1929, a year of intensive field development in California, 48 men were killed in the drilling and producing division, whereas in 1930, a year of less development work, only 25 men were killed in this division. The figures for the average number of drilling and producing wells in 1930 decreased appreciably from, comparable figures for 1929 and a greater percentage of producing wells were shut-in in 1930 than in 1929.

Jan 1, 1931

Maps To Accompany Bulletin 494

Jan 1, 1950

By K. Shimamoto

This study has been prompted by the anticipated demand for rhenium by the petroleum industry and the concern for an adequate supply of rhenium to meet the demand. The present and projected outlook for rhenium relative to its distribution and occurrences, the recovery factors involved in ore beneficiation, capital and operating costs, changing technology, and the projected uses and market growth of rhenium are presented in this report as part of the Bureau of Mines program to determine the availability of recoverable rhenium in a developing market.

Jan 1, 1973

By Bernard Lewis

This report summarizes fundamental research and technical studies conducted by the Explosives and Physical Sciences Division of the Bureau of Mines from July 1, 1949, to June 30, 1950. It is the fourteenth of a series of annual reports whose aim has been to bring to the reader a résumé of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report.

Jan 1, 1951

By Lloyd Williams

1. Reserves have been estimated for three coal beds in Bledsoe County, Tenn.: Morgan Springs, Lantana, and Sewanee. The Richland and Nelson beds occur in Bledsoe County also, but there was not enough information on them for making an estimate of reserves. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated at 43 million tons as of January 1, 1954. Of this total, 22 million tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves deter-mined by this investigation.

Jan 1, 1956

By Robert F. Randolph, Dana C. Reinke, Richard L. Unger

Purpose The NIOSH Hearing Loss Simulator is a software training and communication tool for promoting hearing loss prevention. It allows a user or trainer to demonstrate the effects of noise exposure on hearing without experiencing an actual noise-induced hearing loss. Estimates of the effects of different levels of noise exposure are based on the American National Standard Determination of Occupational Noise Exposure and Estimation of Noise-Induced Hearing Impairment, otherwise known as ANSI S3.44. This standard specifies the predicted hearing loss for noise-exposed populations of individuals based on risk factors that include gender, age, sound levels (in A-weighted decibels or dBA), and years of exposure. Algorithms specified in the standard were derived from empirical studies of populations that had no exposure to loud noise and other populations that had experienced various levels and durations of noise exposure. This manual explains the major objectives that can be addressed with the simulator and training scenarios that can be applied to real-life, real-worker scenarios. The majority of this guide explains the simulator's functions in detail. Simulator users are encouraged to read this manual while learning how to run the software. [ ] Training Objectives The main objective of the Hearing Loss Simulator is to increase motivation for taking effective hearing prevention action by demonstrating simulated noise-induced hearing losses. [The Simulator can also help teach the following facts about hearing loss. Hearing loss is affected by noise levels. Hearing loss worsens as the noise exposure duration increases. Hearing loss can become permanent. Hearing loss makes it harder to hear what others say. Most hearing loss is not caused by age. Speech is made up of both low and high pitch sounds. Hearing loss due to noise makes it harder to hear high pitch sounds. Hearing loss due to noise has less of an effect on hearing low pitch sounds.]

Jan 3, 2008

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By R. B. Anderson

As a part of a Bureau of Mines program on the conversion of coal to liquid and gaseous fuels, the kinetics of the Fischer-Tropsch synthesis on iron catalysts was investigated. Nitrided catalysts were studied at 21.4 atmospheres using feed gases ranging from 2H2+1CO to 0.25H2+1CO, and at 7.8 to 21.4 atmospheres using 1H2+1CO gas. The overall apparent activation energy increased with increasing carbon monoxide content of the feed gas from 19.5 kcal/mole for 2H2+1CO to 23.7 for 0.7H2+1CO. The rate of synthesis with 1H2+1CO feed increased linearly with operating pressure from 7.8 to 21.4 atmospheres. A semifundamental rate equation of the form [r=a'PH2 0.6pco 0.4- ?r0.5PH200.5] was shown to fit the data satisfactorily. The relative usage of hydrogen to carbon monoxide decreased with increasing conversion, passed a minimum, and then increased. Apparently water is the principal primary product and carbon dioxide is produced by subsequent water-gas shift reaction. In another group of experiments water, carbon dioxide, argon, and methane were added to 1H2+1CO feed to a nitrided iron catalyst. Argon and methane were only diluents. Carbon dioxide was a slight inhibitor and water vapor was a strong inhibitor to the rate of synthesis. Water accelerated the water-gas shift and usually increased methane production. Important factors of catalyst geometry in determining rate were found to be particle size and extent of reduction. Apparently the active portion of the catalyst is confined to a layer of 0.01 to 0.02 cm from the external surface of particles. A special solution was made of differential equations relating re¬action at the catalyst surface to diffusion in pores of the catalyst for spherical particles with an active layer surrounding an inert core. The equation derived expressed the experimental data reasonably well. Diffusivities determined by this equation varied from 3 to 24X10-6 cm2/sec; these values are of the same magnitude as observed for the diffusion of gases in liquid. The appendix presents a group of synthesis experiments at pressures of 21.4 to 103 atmospheres. In this range the rate of synthesis on nitrided iron catalysts increased with pressure to the 0.74 to 0.84 power.

Jan 1, 1964

By David C. Oyler

Three long horizontal holes were drilled from a directionally drilled surface hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diameter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a vertical depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 ill (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By Frederick W. Horton

With large deposits of low-grade molybdenum ore and a latent market for molybdenum, which with development might perhaps equal that for tungsten, the United States has for years made no pro- duction of molybdenum ore worthy of mention. In fact, during the decade previous to 1914, there was no output of molybdenum ore in this country except in 1905, 1906, and 1907, when a few small lots of molybdenite and wulfenite were marketed." To ascertain why this possible source of economic wealth should remain undeveloped, the United States Bureau of Mines undertook an investigation in 1914, with a view of assisting the establishment of a molybdenum industry in this country. A preliminary review of the situation showed the following conditions: Briefly there was a lack of any considerable demand for molyb- denum for the one known use that might consume any large tonnage of it, that is, for the manufacture to certain alloy steels to which molybdenum imparts properties roughly similar to those produced by tungsten. It was at once evident that the market for molybdenum in alloy steels must be developed, or that extensive new uses for the metal must be created, before the demand would be sufficient to war- rant any extensive mining of molybdenum ore. Investigation showed that one of the chief factors in retarding the development of any demand for molybdenum by the alloy-steel trade was that manufacturers who might use, or might investigate the possibilities of using, the metal were kept out of the market by the fear of not being able to obtain steady supplies. On the other hand, those who might be interested in the development of some of the extensive low-grade molybdenite or wulfenite deposits in this country were prevented from doing so by the small visible demand and the fear that any large production would glut the market. Owing to these conditions the mining of molybdenum has in the past been confined almost entirely to small-scale operations on high-grade streaks of molybdenite ore, and the methods of recovery have been limited largely to cobbing and hand picking.

Jan 1, 1916

By E. C. Lane

"INTRODUCTION The first important discovery of petroleum in New Mexico was near Dayton, Eddy County, where the Brown well was drilled in 1909, and small quantities of oil were produced. In 1911 and 1912 wells were drilled in McKinley County, but commercial production did not begin until the discovery of the Hogback field, San Juan County, in 1922. The discovery well in the Artesia field, Eddy County, drilled in 1923, gave impetus to active drilling in many areas. Since 1924 New Mexico has produced petroleum in commercial quantities and since 1930 the State has joined the ranks of the big produc¬ing States, being sixth or seventh in total production in recent years.Production by years. 1924 to 1940, inclusive, taken from annual figures in Bureau of Mines Minerals Yearbook, are given in table 1. The total production shown is 274,331,000 barrels. Andreas 3/ has published production figures for the year 1940 and a resume of all production to the end of 1940. Data from his report are presented in table 2 for each field sampled. The cumulative production, as given by Andreas, is 270,618,575 barrels."

Aug 1, 1942

By E. H. Rose

This paper, describing the concentrator practice of the Moctezuma Copper Co., is one of a series being prepared by the Bureau of Mines. The Nacozari concentrator of the Moctezuma Copper Co. (the Mexican subsidiary of the Phelps Dodge Corporation) is located about 75 miles south of Douglas, Ariz., in the Moctezuma District of the State of Sonora. Nacozari is the southern terminus of the Nacozari Railroad, ever which all concentrate is transported to Douglas for smelting.

Jan 1, 1930

By R. S. James, E. J. Gleim

Not long after electrically driven equipment was introduced into coal mines it became apparent that the spark-producing parts, such as controllers and motors, required safeguards to prevent the ignition of mine gas that might come into their vicinity. Many of the early designs attempted to provide protective enclosures having ventila¬tion and relief for pressures if ignition should occur within. The principal feature of the Davy safety lamp, namely, the wire gauze, was employed widely for this purpose. Other devices were developed to reduce the temperature of products of combustion escaping through the protected openings to a value below that which would cause ignition of surrounding explosive atmospheres. Although many such devices performed their intended function satisfactorily under laboratory conditions they were not so satisfac¬tory when subjected to the rigorous conditions encountered under¬ground. Corrosion, mishandling, and accumulations of grease and dirt reduced or destroyed their protective qualities after a period of service in the mines. In the United States this has led to abandon¬ment of special devices in favor of what is called " total enclosure " which means that no regular provision is made for ventilation and release of pressure but rather that the housings or enclosures are built strong enough to withstand the explosion pressures without rupture. As a further protection the joints usually are made of broad, closely fitting surfaces. It is impractical to make such joints absolutely gastight in ordinary machine practice when provision must be made for partial or complete disassembly to facilitate ad¬justments and repairs. Therefore, when an explosion occurs within such enclosures flames may escape through the joints. If the latter are broad enough and not separated too widely, however, the flames will be cooled by contact with the metal surfaces (flanges) of the joints, by rapid expansion, or by both cooling and expansion, with the result that an explosive atmosphere surrounding the enclosure will not be ignited. This is termed " flange protection." In testing parts of cutting machines and other equipment for coal mines, with the ultimate object of approving the equipment for use

Jan 1, 1935

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller:5 Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer's deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone.

Jan 1, 1931

"When a metal-mining company takes out a workmen's compensation insurance policy, it does so to relieve itself of its uncertain and variable financial liability under laps requiring payment to employees for lost-time accidents, there-by passing the liability or to the insuring agency. For this service, or rather for the assumption of the risk, the insuring agency charges the mining company a price, or in insurance parlance, ""a premium"".The insuring agency depends upon a volume and variety of business to average the losses incurred by its individual policy holders, and determines its price to cover losses that are suffered and its cost of doing business.It is generally known that all types of insurance are founded on the theory of probability applied to large groups of risks, Workmen's compensation insurance is no exception, and the average price paid therefor must be based on the frequency and severity of accidents in the particular industry or branch of industry under consideration. The frequency and severity rates are determined by statistics, which, of course, unless standardized, kept carefully and consistently, and analyzed properly, are liable to be inaccurate and misleadingThe importance of large groups in arriving at an average price for insurance service can not be overestimated, For example the writer knows of one small group of some twenty metal-mining companies whose losses during the past two years exceeded their premium charge by 54%. Not a single individual company during the two years kept its losses below the premium rate. For several years the group as a whole has persistently exceeded its premium rate, Such risks are not profitable to the insuring agencies and can only be carried where a large volume of good risks will balance the poor risks, but in order to conform to good insurance ethics the premium rate must be based on averages for the industry as a whole, and kept sufficiently low to induce operators to sell their risks."

May 1, 1924

By Albert L. Toenges

The production of coal from underground mines in Washington declined during the recent war owing to shortage of manpower, and coal was shipped to the Pacific Northwest from mines in the Rocky Mountain region. The movement of this coal into Washington required the use of railroad equipment that otherwise could have been used for transporting war materiel and personnel. Strip mining uses a minimum of manpower, and the development of coal areas in the Pacific Northwest that can be mined by the strip method should increase production in the area, thus releasing railroad equipment from the necessity of transporting coal long distances and also providing consumers with a lower-cost product. The development of a strip mine to supply the demand at low cost requires a large investment in heavy equipment. In order that the fixed charges due to large investment in plant and equipment may be kept at a minimum, large reserves of coal must be proved. A reconnaissance of an area near Toledo, Lewis County, Wash., indicated a large bed of lignite that could be mined by strip methods. The area is approximately midway between Portland, Oreg., and Tacoma, Wash. (refer to fig. 1), and the opening of a large mine in the area would supply fuel to these and other nearby centers.

Jan 1, 1947