Search Documents

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By Alla D. Mah

Compilation of data on materials of metallurgical interest is one of the important activities of the Berkeley Thermodynamics Laboratory of the Bureau of Mines. Recent renewed interest in metallurgy of vanadium renders the present compilation a timely guide for experimentation to improve present methods or to develop better methods of extractive metallurgy. Thermodynamic data for vanadium and its inorganic compounds have been critically surveyed, selected, and compiled into one convenient reference from which information can be readily obtained for evaluating heat balances, determining trends, and establishing limits of metallurgical processes. By indicating the direction of experimentation, this report enables the saving of time, effort, and expense which would otherwise be necessary for trial and error experimentation. Much of the data has been obtained experimentally at the Berkeley laboratory. Other data were collected through an extensive survey of worldwide literature through April 1965. Estimates were made when no data were avail-able. Data on the vanadium halides was sparse, and the results derived from existing data were at times divergent. Some of the selected values for the halides may need modification as more or better experimental data become available.

Jan 1, 1966

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

By Mark Sheppard

This paper is the third of a series recording the results of tests made at various quarries throughout the United States to determine (1) the relation between the size gradation of feed to, and product from, primary crushers, (2) the particle shape of the crushed product, (3) the differences in gradation and particle shape produce- by different types of primary crushers, and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Progress reports 1 and 2 dealt with comparisons of different types of crushers crushing the seine tyre of stone. This report deals with relationship between feed and product of two different limestones, as to size distribution and particle shape, when crashed in the same crusher.

Jan 1, 1938

By Cleo G. Rall

The value of brine analyses in the study of petroleum-engineering problems was recognized early in the history of petroleum. The Bureau of Mines before 1928 had indicated in several reports.3/ ways in which analyses might be used. Because of the confusion resulting from attempts to correlate the work of different chemists using greatly varying methods of analysis and systems of computation and expression of results, a paper presenting the methods used by the Bureau of Mines was prepared and published in 1928. This system of determining the characteristic constituents of oil-field waters and of calculating and reporting results has been widely adopted by the petroleum industry. The earliest and most obvious use of water analyses is determination of the source of water infiltrating into petroleum and natural-gas wells. For this purpose it is necessary that an analysis of the connate water of the formation from which the oil is produced be available and that an analysis of the contaminated water be made. By comparing these analyses with those of connate waters from formations higher in the structure, the formation from which the infiltrating water comes may be identified.

Jan 1, 1953

By Summer S. Smith

The year 1916 broke all previous records of mineral production in the Territory. As a consequence, there has been a noteworthy increase in the number of mines in active operation or under development, though the greater part of the increased output is the result of greater activity at mines already producing rather than of opening new mines. Owing to available funds not being sufficient to meet the cost of travel in the interior of the Territory during the winter months, the Federal mine inspector was unable during the spring to visit the placer mines of the interior as has been his custom in the past. However, by working in close cooperation with the Territorial in- spector, who left Juneau in June to take the first boat down the Yukon to Fairbanks after the spring break-up, it was possible to visit hurriedly all the larger mining centers of the Territory. The Territorial inspector covered the districts from Fairbanks to Nome and the Federal inspector covered those of southeastern and south- western Alaska. A number of applicants have begun mining coal on ground held under free-use 10-acre permits, and have furnished coal for local use. The larger leasing units in the Bering River and Matanuska coal fields have been advertised and applications for leases have been submitted. These applications came too late in the fall for active development to begin before the end of the year. The Government railroad has been built from Anchorage to the center of the Matanuska coal field, and private interests have under- taken the building of a standard-gage road from a point known as Goose City on Controller Bay to Canyon Creek, in the Bering River field. Capital has become interested in the oil fields on Controller Bay, and plans have been made for more active exploration and production. The work of the Federal mine inspector is still handicapped by the lack of funds for additional field assistants and of the office ac- commodations necessary for carrying on the work with the efficiency that its importance warrants.

Jan 1, 1917

By R. R. Backer

The Bureau of Mines investigated the typical physical and chemical properties of coal waste materials from the western part of the United States. The results are compared, in so far as possible, with the properties of waste materials from eastern coal operations. The authors found a disparity of mines and preparation plants among western U.S. coal operations and dissimilarities with typical operations in the East. The relatively cleaner product from the predominance of surface mining and the occurrence of thicker seams in the West reduces the amount of coal preparation required and the size of the waste piles. Because of the abundance of land available for waste disposal, many of the piles are low and extended over large areas. New concepts relating statistical shear strength data to liquifaction potential are presented. The somewhat limited data indicates that western coal sludge is coarser with higher permeabilities and shear strengths than the eastern deposits.

Jan 1, 1977

By P. R. Tisot

Knowledge acquired from this research contributes to a better understanding of the physical structure of Green River oil shale and provides fundamental data and concepts that may serve to improve oil-shale technology. This study by the Bureau of Mines indicates that oil shale is a highly consolidated organic-inorganic system with no significant micropore structure, pore volume, or internal surface. This system is a form of physical structure that precludes rapid diffusion of either gases or liquids. The mineral matter consists essentially of nonspherical particles that tend to follow a log-normal size distribution. An excess of 99 weight-percent of these particles have equivalent spherical diameters of less than 44 microns--75 weight-percent are from 2 to 20 microns, and 15 weight-percent are less than 2 microns. The surface area (3 to 5 square meters per gram) of these mineral constituents is mainly external surface. The mineral constituents contain some micropore structure--pore radii ranging from 10 to 100 Angstrom--with the pore sizes randomly distributed. Distribution of the organic matter within the inorganic matrix is essentially interparticle and not intraparticle. The organic matter within the micropores of the mineral constituents is less than 4 percent of the total. Estimates made from surface area data suggest that perhaps only a small amount of the organic matter is bonded either physically or chemically to the mineral constituents.

Jan 1, 1963

By H. D. Jacobs

A process for recovering both iron and manganese from four manganiferous ores of the Cuyuna Range was evaluated. It comprised: (1) Low-temperature gaseous reduction to convert nonmagnetic iron minerals to magnetite and manganic minerals to manganous oxide, (2) acid leaching to extract manganese, and (3) magnetic separation to reclaim iron from the leach residue. Iron recoveries from the magnetic products ranged from 70 percent to 90 percent; manganese recoveries from leach filtrates ranged from 75 percent to 95 percent. Two ores, from the Hillcrest and South Alstead properties, yielded magnetic products considered adequate for use as blast furnace feed. Although good yields of manganese were attained on all ores, appreciable iron accompanied the manganese into solution. Previous work, however, has shown that this iron can be precipitated almost quantitatively under autoclave oxygen pressure with very little loss of manganese.

Jan 1, 1970

By D. S. Burgess

A commercially available Halon 1301 extinguisher has been evaluated as part of an explosion-suppression system for use in coal mines. Studies were made both of the dispersion pattern of the Halon 1301 at an initial pressure of 280 psig, and of the efficacy of this suppressant against 9.5 percent methane-air flames. These flames were quenched successfully only when the suppressant was applied before the fireball diameter exceeded 18 inches.

Jan 1, 1971

By R. V. Higgins

This paper describes a method and a computer program for calculating shape factors and areas of channels that turn more than 90° and conduct fluids into the backs of wells. The program represents an improvement over a previous Bureau of Mines investigation by using a 4-point Lagrange interpolation equation instead of a 3-point and by summing areas of trapezoids with either x altitudes or y altitudes. Some of the techniques reported in this paper can also be used to compute the areas between contours and the lengths of lines that turn more than 90°.

Jan 1, 1968

By A. J. Barry

Recent developments in mechanizing longwall it mining in Europe have aroused considerable interest among American coal-mine operators because this method provides an opportunity to improve safety, production, efficiency, and recovery. The success of longwall mining in Europe has depended to a large degree on development of effective roof-control systems. One of the major contributing factors in designing these systems is development off improved supports, which combine high load-bearing capacities with controlled yield characteristics, to use in the face areas. Other factors that relate to successful longwall mining involve knowledge of the structural properties of the strata above end below the coal bed being mined, movements of these strata induced by mining, and effects of the strata movements on the strata itself, as well as on the support system used. Extensive studies of the above factors relating to long-wall mining have been made in coal-mining countries abroad, and corresponding studies (1, 2, 3, 4, 5)3/ of room-and-pillar operations have been made in this country. Although descriptions and results of experiments of mechanized longwall operations in the United States have been published (6, 7, 8), this is the first instrumented study of roof behavior on a longwall operation. In view of the possible widespread application of this method of mining to American coal mines, where underground mining conditions are different from those found in European mines, an investigation was conducted at a mechanized longwall operation inn the Lancashire No. 15 mine, Barnes & Tucker Co., Cambric County, Bakerton, Pa., to study the factors that affect roof control. This report describes this investigation and discusses the results. ACKNOWLEDGMENTS This investigation was made under a cooperative agreement between the Bureau of Mines and the Barnes & Tucker Co., Barnesboro, Pa., end was conducted in the Lancashire No. 15 mine located at Bakerton, Cambria County, Pa. The authors acknowledge the cooperation given by Richard Z. Todhunter, Sr., president, Richard T. Todhunter, Jr., general manager, and other mine officials and employees of the Barnes & Tucker Co. Mr. Edward Thomas, chief, Roof Control Section, Bureau of Mines, Washington, D. C., and Dr. Leonard Obert, chief, Applied Physics Branch. College Park, Md., collaborated in the planning and promulgation of the program investigation.

Jan 1, 1954

By D. P. Schlick

As of June 30, 1970, Federal regulations required the operator of each underground coal mine to maintain the average concentration of respirable dust below legislative standards. As of March 1, 1971, over 152,000 respirable dust samples have been processed by the Bureau of Mines. Approximately 75 percent of underground working sections are being sampled in accordance with Federal regulations. Results indicate that 72 percent of the sections which have completed at least one basic sampling cycle are below 3.0 mg/m3, the standard in effect under the Federal Coal Mine Health and Safety Act of 1969 (P.L. 91-173). Notices of Violation were issued on 1,670 underground mines for failure to begin a sampling program; Withdrawal Orders were issued in 64 of these instances. Notices of Violation were issued on 1,121 sections where applicable dust levels were exceeded; Withdrawal Orders were issued in seven of these instances. There are 381 mining sections currently operating on permit; from the interim Compliance Panel.

Jan 1, 1971

By N. S. Dalal, Xianglin Shi

"Electron spin resonance (ESR) measurements provide direct evidence for the involvement of Cr(V) in the reduction of Cr(VI)· by NAD(P)H. Addition of hydrogen peroxide (H2 O 2) to NAD(P)H-Cr(VI) reaction mixtures suppresses the Cr(V) signal and generates hydroxyl (·OH) radicals (as detected via spin trapping), suggesting that Cr(V) reacts with H2O 2 to generate the ·OH radicals. Reaction between H2O 2 and a Cr(V)·glutathione complex, and between H2O 2 and several Cr(V)-carboxylato complexes also produces ·OH radicals. These results suggest that Cr(V) complexes catalyze the generation of ·OH radicals from H2O 2, and that ·OH radicals might play a significant role in the mechanism of Cr(VI) cytotoxicity. KEY WORDS: ESR. spin trapping, Cr(VI) reduction, Cr(V), hydrogen peroxide, free radicals.INTRODUCTIONThis communication reports an ESR spin trapping detection of hydroxyl ( OH) radicals.in reactions between some Cr(V) complexes containing biologically important ligands and hydrogen peroxide (H2O 2 ). This work was undertaken because while the reduction of Cr(VI) to lower oxidation states has been suggested as a key step in the mechanism of Cr(VI) toxicity, the reaction· mechanism is not yet clear. 1 Mutagencity has been well documented for Cr(VI) via various bacterial assays, while Cr(III) has been shown not to be mutagenic.2 • 3 Since it has been reported that compounds containing Cr(VI) do not react with isolated DNA,4 the reduction of Cr(VI) by other cellular constituents has been thought to be important in the mechanism of Cr(VI) induced DNA alteration.1·4 • 5 For cellular systems earlier studies include those on the reduction of C~(VI) by microsomes,6-8 rat liver DT-diaphorase,9 and aldehyde oxidase. 10 Regarding the reduction mechanism, Jennette used ESR spectroscopy to show that a long-lived Cr(V) complex is formed as an intermediate in the microsomal reduction of Cr(VI) in the presence of NADPH.8 She postulated that Cr(V) is the ""ultimate"" carcinogenic form of chromium compounds. This conclusion has led to many further investigations of the formation of Cr(V) in the reduction of Cr(VI) under biologically relevant conditions.11 - 19 More recently, however, it has been suggested that oxygen-derived radicals generated during the Cr(VI) reduction are the species responsible for the DNA alteration.20.2• To the best of our knowledge, however, no information is available on the generation of such radicals in the reduction of Cr(VI) under biologically relevant conditions, except some preliminary results on the glutathionyl (GS·) radical formation in the reduction of Cr(VI) by glutathione (GSH). 11 - 19 We, therefore, undertook a systematic investigation of the reaction of Cr(VI) with NAD(P)H, GSH, ix-hydroxycarboxylic acids, and H2O 2 • NADPH was chosen as a model reductant because of its ubiquitous existence inside the cells, its critical role in the enzymatic Cr(VI) reduction,1·6-9 its representation of important cellular Cr(VI) reductants, and its ability to reduce other metal ions.22 GSH was chosen as another model Cr(VI) reductant because GSH also exists inside cells, it represents another important category of cellular Cr(VI) reductants, the thiols, and it also plays an important role in the Cr(VI) toxicity .1• 1 ""- 19.i3.i4 For further clarification, we also studied the reaction of Cr(VI) with several '1'.-hydroxycarboxylic acids in the presence of H2O 2 since these acids are definitively known to reduce Cr(VJ) to form stable, isolable Cr(V).25 .2 6 The results obtained indicate that Cr(V) complexes, produced in the reduction of Cr(VJ) by cellular reductants, react with H2 O 2 to generate ·OH radicals, which might be the initiators of primary events in Cr(VI) carcinogenicity."

Jan 1, 1990

By D. A. Rice

As part of its mission, the U.S. Bureau of Mines continues to develop technologies that will enable cost-effective compliance with environmental requirements. To this end, investigations to improve the kinetics of chalcopyrite dissolution by simultaneous grinding-leaching in ferric sulfate solution were conducted using the Bureau-designed turbo mill. The development of such a hydrometallurgical process would provide a nonpolluting alternative to conventional smelter technology. The effects of mill rotational speed and volume percent solids on the leaching time and energy required for copper extraction from chalcopyrite were evaluated. The results of this laboratory study have shown that the simultaneous grinding-leaching of chalcopyrite concentrate using the turbomill is technically feasible with essentially 100 pet extraction of copper being possible at 90° C. An optimal energy consumption of 1,153 kW?h/st of copper leached was found in batch testing with the mill operating at 400 rpm with a slurry containing 35 vol pet chalcopyrite. This energy consumption, while higher than other proposed leaching processes (about 600 kW?h/st), is of the same order of magnitude. Further refinement of the energy requirements would require additional testing using a continuous circuit. Leaching times of less than 1 h, for 80 pct copper extraction, are achievable using the turbomill grind-leach process.

Jan 1, 2010

By K. S. Gritton

The Bureau of Mines investigated the feasibility of numerlcally modeling the sorption of cobalt, a vulnerable strategic and critical metal, from spent copper leach solutions in a multiple-compartment ion-exchange (MCIX) column. Equilibrium resin loadings, cobalt-sorption kinetics, and resin-fluidization characteristics were determined in simple laboratory tests, and a numerical model was developed to predict cobalt extraction and the MCIX-column resin inventory based upon the test results. The model was implemented on a microcomputer to approximate the solution to the set of differential equations that govern model performance. Results compared very well with data from 12 pilot-scale MCIX-column experiments. The average difference between predicted and actual cobalt extractions was 3.2 pct; the maximum difference was 9.3 pet. The actual and predicted resin inventories differed by an average of 5.8 pet, and the maximum difference was 12.0 pct.

Jan 1, 1987

By W. H. Coghill, B. W. Gandrud, F. D. DeVaney

"The self-fluxing iron ores of Alabama are the foundation of the thriving iron and steel industry of that State. In addition to these deposits of self fluxing ores there are seams containing practically the same percentages of iron but too much silica. These ores at present are valueless, but if they could be concentrated by reducing the silica content, the ore reserves of the Birmingham district would be greatly augmented. A detailed report on the iron-ore deposits of the district, describing the types of ore and their extent, has been published.In forwarding its mineral conservation policies the United States Bureau of Mines has given some attention to the siliceous ores of this district.The low cost of gravity concentration gives this process first rank in the beneficiation of iron ores. For this reason many experimenters have tried to concentrate the Alabama iron ores on tables. In the face of the early failures a new trial has been made and the results have justified the effort.In this work more attention than formerly has been given to the physical, properties of the ores. The removable siliceous gangue is in the form of oolitic grains which ""shell"" out like corn, leaving the hematite as rich high-grade ""slime"" and as clean granular grains. The ""slime concentrate"" may be recovered by well known desliming processes. The oolitic grains and granular hematite are separated on tables."

May 1, 1929

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By William C. Smith

Roof support, an important aspect of ground control, involves maintaining roof competency to ensure a safe and efficient mining environment. Wide variability in rock quality and stress distributions requires a systematic approach to roof support design that satisfies specific goals. The success of past roof sup-port in reducing the incidence of roof falls has been primarily attributed to safer roof bolting practices. However, roof falls continue to be the number one occupational hazard in underground coal mines. This U.S. Bureau of Mines report presents a general overview of roof bolting and other roof support methods used in the United States. Characteristics of bad roof and associated roof failure theories are briefly presented as background to roof support. Methods of detecting and monitoring roof behavior and/or bolt performance provide essential feedback on roof support requirements. A discussion follows on roof bolt design that assimilates roof and support parameters into useful equations or nomographs to help decide what bolt types to use and how they should be installed under different roof conditions.

Jan 1, 1993

By F. G. Miller

[Petroleum technoloF;istz and 1 rot-re s s ive OT e:?ztors. con stantl;, are striving to increase the percentage of oil that y to recovered from reservoir rocks throe::;:: wells. The exhaustive studies that have been made of the function of natural r:; as in t h-_ T r odI action of oil, for cx<n.mTnle, have aidedd of.erators greatly in incroasin,&apos; the q-:Arrntity of oil recovered from reservoirs. i.rtural gas dissolv3d in ar--d otinerwwisa &apos;1s&apos;.,ocintjd under rre3suro with oil in roscrvoir roci.s, howover, i:; not the only source of energy available for moving oil through sa&apos;:&apos;l to wells. l becoming "reservoir-energy conscious&apos;t engineers hr-vo -d o^.rued t}:-Lt in many petroleum reservoirs the edgewater flanking t -,e oil accum.-,lation conetitutos a potential source of onergy capable, tL-ou;_h rro? gr control, oil&apos; increasing oil-recovery efficiencies materially. i o ]enter is ti-.-,, on-cronchinunt of water into the oil- and gas--fillod ?art of the reservoir considered as an evil to be combatted by devious mot&apos;:r:ci :i,.t r,ttL er a natural conseque::c4, incident to the withdrawal of oil nna gas from the wells, that nay be T.usod advantrt eou ;ly in lonr`t}toning tr e r&apos;lowin g lift of wells a.nd, i norcas in:; the economic recovery of oil and Little is known about the by which water off: oratos in driving nil throe:gh reservoir roc:-.:,, nd i:. a scorcity of rubli:;Lad informs-¬t .on nn rates of :)Ov.:m.,:- t of : r.tcr ..at v:1:11 res,-_lt in ^r i-nu oil recoveries. Bureau of :fines engine_:? ; - reciate. the r,aucity of scientific knowledge or. the &apos;test methods of a,r.lying the natural water arive to in¬crease oil-recovery efficiencies ant ,i.;?l __-itir?,~ ting irties that will, they hope, Contribute to t.1&apos;.e T ros?Jr.t. small _ %nd of information now av tilable on tt:e cubjoct. This r».crt a oyno-.::is or brief comrilnt.ion of r,ublished data and thought accuinulnt.~d so far, to la)or;~.tory ox-:erimnntrr¬tiorn and, further rosoarch on the z_rrinciplos unri;rlyir..g the natr.rr+1 eater drive no it nffocts oil recovery. :Lie writer:: Lore that t.i.c cx-nositiorn of a?rzilable inforr-at ion i rcs?r.toi in the rernrt r .-II .i ,.1rtt cor_jt_-i:ctive tho.-_.I_t and efforts loadir,-z to -:ard more con.r .ote extraction n;&apos; o tl from reservoirs.]

Jan 1, 1938